Server :: Setting Up The Static Ip Address With A 2wire Gateway From Att
Oct 22, 2010setting up my ubuntu server I would also like to run ubuntu desktop for the GUI.
setting up the static ip address with a 2wire gateway from att.
ADVERTISEMENT
Networking :: Change Static Gateway Ip Address?
Mar 31, 2010when I do "route -n", I got:
Code:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
I need to change the static configuration, like I 169.254.0.0, I don't know how it got there also I want to delete 192.168.1.1 from a static gateway. How can I do this?
Networking :: Hold Static Ip Address From A Different Gateway Router ?
Jul 6, 2010I'm running Ubuntu 10.04 and my setup is as follows:
As you can see, I am directly connected to router 192.168.25.1, and so my ip address is 192.168.25.101. I want my ip address to be 192.168.13.101, and make router 192.168.13.1 my gateway router. Is this possible under the current physical layout (I do not want to have to connect directly into 192.168.13.1, but keep my computer where it is at)?
When I run tracepath, it shows 192.168.13.1 is one hop away.
What I've tried:
The problem is under this manual setup, I cannot ping 192.168.13.1 and running command netstat -rn returns the following:
Ubuntu Servers :: Setting Static IP Address ?
May 17, 2010I just upgraded to 10.04 and I want to set the static ip address but I can't find where to do it.
View 2 Replies View RelatedOpenSUSE Network :: Setting Static Local IP Address?
Feb 18, 2010how I can define a local static IP address (so that I can run a web server off of the same IP, rather than letting my router DHCP it)?I've tried doing the YaST->Network Devices->Network Settings->Traditional Method with ifup->Set NIC to desired IP->Set Default Gateway to router address method, and afterwards I can't even get into my router anymore (not even responding to ping).
View 8 Replies View RelatedNetworking :: Enable DHCP Setting In Fedora 12 / Using Static Address?
Jan 2, 2011My DHCP setting is disabled in fedora 12 . Previously i was using static IP address. I Want DHCP setting enable, any idea.
View 1 Replies View RelatedUbuntu :: Getting A Gateway To The Internet When Setting Eth0 With A Fixed IP Address - Lucid Lynx
Jul 7, 2010I have trouble getting a gateway to the internet when setting eth0 with a fixed IP address. The gateway address (192.168.2.1 my modem/router) resets to 0.0.0.0 whenever I apply the changes. DHCP works fine but I need a fixed address for my server.
View 6 Replies View RelatedCentOS 5 Server :: Trying To Assign Static IP Address
May 1, 2010i am trying to assign a Static IP address and for the life of my i cannot get it to work Can someone explain to me the easiest way to do it and if i restart the server it won't get lost either.
View 1 Replies View RelatedUbuntu :: Setting Up Static IP In Server?
Mar 21, 2010Well basically the title how to setup a static IP in Ubuntu Server?
View 3 Replies View RelatedNetworking :: DHCP Server - Losing Static IP Address
Nov 10, 2010I have an Ubuntu Server 10.04.1 that I have given a static IP address. Every six hours or so I will lose connectivity to it and when I type ifconfig to look at the network information, it has been given an address via dhcp. If I run the /etc/init.d/networking restart command the IP address goes back to my static address and things are fine for another 6 hours or so. Here is what is in my interfaces file:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 10.60.82.15
netmask 255.255.0.0
broadcast 10.60.255.255
gateway 10.60.254.254
This machine is also a DHCP server and I checked to make sure there are no other DHCP servers on my network. Right now my fix is to have a Cron job running that runs the reset command every 5 hours, but I would like to find a more permanent solution.
General :: Point Domain To Server With A Static IP Address?
Sep 4, 2010I am trying to point my domain to my server with a static IP address. My domain is registered with Network Solutions and they ask "Primary and Secondary DNS" settings in their setup. What primary and secondary DNS settings I need to give when I have a dedicated server with static single IP address with BIND installed.
View 1 Replies View RelatedUbuntu Networking :: Make Home Server Use A Static Ip Address?
Mar 15, 2010i have followed multiple guides to make my home server use a static ip address. no matter what i do it always reverts back to its dhcp address after about 2 minutes. how do i get the static ip address to stick, or be permanant.
View 9 Replies View RelatedUbuntu Networking :: Set A Static IP Address On A Server (to Be Used With Mythtv) And Is Running Mythbuntu 10.04
Aug 12, 2010Am attempting to set a static IP address on a server (to be used with Mythtv) and is running mythbuntu 10.04 (apologies if this is the wrong place to post this). I can set a static IP address that is in the range of 192.168.1.x on other machines on the network but when I try with the server it is not able to connect to the network. When using the DHCP rather than manually assigning the address it is assigned an address with the 10.0.0.x range. Why is it doing this I have never have this problem on other ubuntu boxes (and this one prior to a format of the OS).
The router/gateway is 192.168.1.1 I did have a DHCP server on the mythbox before formatting it and I was able to assign a static 192.168 address and retain internet connectivity. But I have re-enabled the DHCP server on my router since formatting the box.
Ubuntu Networking :: Static IP Address And The Install Configures For A DHCP Configured Address - Network Not Starting
Dec 16, 2010Version 10.04 LTS. Installed desktop version and network worked but I needed a static IP address and the install configures for a DHCP configured address. I tried changing to static address using the System->Preferences->Network Connections application but was unable to get the system to come up with the network up.
So I manually modified the /etc/network/interfaces and the /etc/resolv.conf files. I restart the system but when I do an ifconfig, I don't see a configured IP address on eth0 (only the loopback address). If I run /sbin/ifup eth0 everything then works fine and ifconfig shows the correct address bound to eth0.
My files are as follows:
Networking :: Static IP Address That Has A Reverse Lookup To "myipaddress.static.lyse.net" And Not Email Domain?
Apr 26, 2010I got this message on Friday from just one domain. uote:mailsrv.forthnet.gr #<mailsrv.forthnet.gr #5.5.0 smtp; 554 5.5.0 Your message was considered to be spam by the FORTHnet Antispamming Policy and was not delivered to the recipient. The following spam tests returned positive for this message:FORGED_RCVD_HELO,RCVD_IN_BRBL. For further information visitWe are not a spamming community but it seems we have a statice IP address that has a Reverse lookup to "myipaddress.static.lyse.net" and not my email domain. Would setting a cname mail.mydomain.no -> myipaddress.static.lyse.net cure this problem or are there more tricks to be performedOnce I have cured the FORGED_RCVD_HELO I can move to getting the IP removed from BARACUDA.
View 2 Replies View RelatedNetworking :: How To Add Gateway (Static IP)
Jul 12, 2011I have 2 lancard eth0 connected to local lan eth1 connected to bsnl broadband connection, I have centos 5.3 here I configure broadband in dial up mode. I am unable to ping outside world and unable to access some site but able to access internet like google etc, configure file is as:
eth0 Link encap:Ethernet HWaddr 00:14:85:96:1C:A7
inet addr:182.x.x.24 Bcast:1182.16.255.255 Mask:255.255.0.0
inet6 addr: fe80::214:85ff:fe96:1ca7/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:736487 errors:0 dropped:0 overruns:0 frame:0
TX packets:859918 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:122617961 (116.9 MiB) TX bytes:772581200 (736.7 MiB)
Interrupt:185 Base address:0x6000
eth1 Link encap:Ethernet HWaddr 00:08:A1:7B:A0:F9
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::208:a1ff:fe7b:a0f9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:658246 errors:0 dropped:0 overruns:0 frame:0
TX packets:620456 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:728744445 (694.9 MiB) TX bytes:100768525 (96.1 MiB)
Interrupt:193 Base address:0x4000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:21198 errors:0 dropped:0 overruns:0 frame:0
TX packets:21198 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5867015 (5.5 MiB) TX bytes:5867015 (5.5 MiB)
ppp0 Link encap:Point-to-Point Protocol
inet addr:59.xx.xx.xx P-t-P:59.xx.xx.1 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1460 Metric:1
RX packets:793 errors:0 dropped:0 overruns:0 frame:0
TX packets:968 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:528818 (516.4 KiB) TX bytes:148274 (144.7 KiB)
[root@venus ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
59.xx.xx.1 * 255.255.255.255 UH 0 0 0 ppp0
192.168.1.0 * 255.255.255.0 U 0 0 0 eth1
169.254.0.0 * 255.255.0.0 U 0 0 0 eth1
182.xx.0.0 * 255.255.0.0 U 0 0 0 eth0
default * 0.0.0.0 U 0 0 0 ppp0
I am unable to ping gateway of ISP IP i.e gateway of static IP.
Networking :: How To Setup Static Routes - Gateway ?
Jan 18, 2011I have a temporary system up with wlan0 and eth2.
I want the eth0 address to be the gateway for accessing the internet on wlan0.
How do I setup static routes?
I'm not too keen with networking...
Code:
Server :: Setting Up Email Address For Outgoing Mail
Dec 1, 2009I have setup mail server on Ubuntu 9.10 and it's is working fine.I am using Webmin to addministrate my mail server.My Ubuntu server name abcs.I send a test mail from Wedmin for user gom.Why it keep adding InfoNet. What I would like is setup as gom@abcs.com.
View 1 Replies View RelatedNetworking :: DHCP3 Server - Setting Double Range Of IP Address
Apr 27, 2010I would like to set a double range of IP address with my DHCP3-server. Now, I have eth0 (which is my only network card) with this IP address : 172.16.93.1 and I have created a second interface eth0:1 with this address: 192.168.3.1. The goal is to give an IP address 172.16.93.X to phones (with option 66) and the IP address 192.168.3.X to the computers.
This is my DHCPD.conf :
ddns-update-style none;
option domain-name "mycompany.com";
option domain-name-servers 172.16.93.1;
default-lease-time 3600;
max-lease-time 2347200;
authoritative;
log-facility local7;
option ip-forwarding off;
default-lease-time 20;
max-lease-time 20; .....
Right now my DHCP server work fine, (I means, no error at the startup ) but the server give always the same kind of IP address, whatever if it's a phone or a computer. I notice something "wired", if I put the :
subnet 192.168.3.0 netmask 255.255.255.0 {
range 192.168.3.100 192.168.3.199;
option routers 192.168.3.254; }
(Which is first in the dhcpd.conf) after the "subnet 172.16.93.0 netmask 255.255.255.0", the server will give IP address 172.16.93.X at all the clients. Is it possible to give more than one IP range with one network card at the same time? And how set the option 66 to only give IP address (172.16.93.X) to the phones?
Ubuntu Servers :: When Attempting To Switch To A Static IP Address, The Vent Client Will Not Detect The Vent Server At All?
Nov 18, 2010I've been attempting to figure this out for about 4 days straight, so far it has not been fruitful. I've installed Ubuntu 10.04 server onto my former gaming system, Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz, 2 cores with 2 GB ram. Overkill I'm sure, especially for a simple personal voip, htpc, storage server.
The problem is only noticeable when I have the vent server running, on the 10.04 server, and I attempt to connect to it through the LAN via the client on my windows computerEverything works fine and connects, LAN and from the outside, as long as the server is set to DHCP. However when attempting to switch to a static IP address, the vent client will not detect the vent server at all.Aside from an annoyance at having to stick with DHCP, I am still curious as to why the static settings will not function. Something so simple has turned into something quite difficult.
I can still connect to the Webmin interface and Putty into server with either DHCP or static IP enabled.I've performed the following troubleshooting steps so far:1) Followed the directions at https://help.ubuntu.com/8.04/serverg...iguration.html2) Edited the /etc/network/interfaces file through the CLI with nano and through notepad on the windows computer3) Through Webmin I've assigned the static IP, although for some reason it does not include a gateway field.4) I've rebooted the server5) I've issued the CLI
Code:
sudo /etc/init.d/networking restart
Here is the file /etc/network/interfaces:
[code]....
Fedora Networking :: Static IP Cannot Contact The Internet Or Even Gateway Router?
Jul 29, 2011I have a fedora 14 box which has a static IP and I can not contact the internet or even my gateway router.I know it has to do with my kernal IP routing table but I can not find the command to do what I need...Here is my kernal IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
My gateway is 192.168.1.1 and my static IP is 192.168.0.2.
Server :: OpenVPN Range Address / When Change Static IP To Dynamic IP In Config File OpenVPN Didn't Work?
Feb 13, 2010I want to configure a VPN over the Internet.I installed the 'openvpn' package, generated the key file, transfered it by a secure way to the client, and setted up the configuration file.
So, in that configuration file I input the IP addresses of the tunneled interfaces. Both IPs are static in the tunnel.
Then, I've heard somewhere that I can assign a dynamic configuration IP for the client. I do this registering a range.
Well, when I tried to change static IP to dynamic IP (changing '192.168.0.2' to '192.168.0.0/24') in the configuration file, the OpenVPN didn't work.
Obviously I don't know what I'm doing, and I really, don't believe that simply changing the IP will make it work, but I tried.
I hope I explained my problem as well.
My configuration file:
# OpenVPN Server Configuration File
dev tun 0
ifconfig 192.168.0.1 192.168.0.2
cd /etc/openvpn
secret key_file
In client I execute the 'openvpn' without the '--daemon' parameter.Then I want that my client uses a IP in a range (192.168.0.0/24, for example), instead of a static IP (192.168.0.2).I also thought to use a DHCP server, but I'm not sure that will work.
Programming :: How To Get Gateway Address
Nov 18, 2010you know ,we can get a Iface's MAC Address,IP Address,NetMask by function ioctl(), But how Can I get a Iface's Gateway by ioctl or other funciton!
View 5 Replies View RelatedCentOS 5 Networking :: How To Set Gateway IP Address
Apr 12, 2010I have a requirement of switch between wireless network with a single wireless device. First it should be switched to adhoc mode and then after sometime switch to infrastructure mode to establish internet connection. Everything works fine except the gateway settings.
I have used:
system("route add default gw x.x.x.x dev wlan0") to set the gateway, where x.x.x.x is gatewayip address.
I have used this whenever switching happens in addition to ifconfig command to set the ip address and netmask. But this is not setting the gateway ip address. How to set gateway IP address?
System details below
OS :CentoS 5.3
Kernel :2.6.18
Fedora Networking :: Change In Gateway Address?
May 26, 2009OS:Fedora core 6
I have just changed my gateway address,now I can access internet with my browser but unable to run add/remove software as it says no network connection available,system updates are not working as well. What should I do make these working?
OpenSUSE Network :: Gateway Changing The IP Address?
Mar 14, 2010I am coming across a strange error with my gateway. When I do a "ping", this is what I get below:
k-63a5b848c6cb4:~ # ping simba
PING simba.gateway.2wire.net (192.168.1.69) 56(84) bytes of data.
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=1 ttl=64 time=0.041 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=2 ttl=64 time=0.029 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=3 ttl=64 time=0.023 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=4 ttl=64 time=0.015 ms
Is the gateway doing something strange?
General :: Get Ppp Interface Gateway Address In Debain 6
Jun 10, 2011I am using debain 6 and using a Sierra modem c888 to connect internet. I am using wvdial package for connecting the modem. I am able to connect internet. The question I have is, how do get the gateway address of the newly created ppp0 interface?
View 1 Replies View RelatedNetworking :: Getting Default Gateway Ip Address On Interface From ISP
May 4, 2011Im trying to achieve the multiple uplinks/provider found on LARTC.org. I have to get the IP addresses from my interfaces (EF1 and EF2) by using a script, but i dont know where to look at for the default gateway from each interface which got their ip address from my ISP.
View 1 Replies View RelatedGeneral :: How To Configure IP Address / Gateway In Ubuntu 9.10
Mar 2, 2010As a new user I like to know how to configure ip address, gateway etc in ubuntu 9.10. I used opensuse 11.1, their I can manage to do these but ubuntu I did not find anything.
View 2 Replies View RelatedUbuntu :: Static IP Address Cannot Be Set?
Apr 20, 2010I have been fiddling around with my ip address configuration using several sources, and this is what I have in the /etc/network/interfaces file:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 192.168.1.122
broadcast 255.255.255.255
netmask 255.255.255.0
network 192.168.1.0
gateway 192.168.1.254
Yet, this is what I have in the ifconfig after I restarted the computer:
[Code].....
Could there be any mistakes I have made in the file? Why is it that I seem to have set a static ip address here and is not working?