OpenSUSE :: Dolphin Slow Wildly Down When Copy Files?
Dec 1, 2010
on my dell xps M1530 dualcore duo 2.2GHz 4GB ram 500GB harddisk suse 11.3 KDE 4.4 and KDE4.6beta1, when I copy big or a big number of files (20 or 30 files 500MB each) dolphin slow wildly down, especially when I copy from a smb:// to my disk, dolphin start immediately to copy but when I click on a tab or a folder (a one that I didn't opened before) dolphin shows it to me after a couple of minutes, is it possible to solve??
For anyone experiencing dolphin freeze ups after updating to KDE 4.5.00 For openSUSE 11.3 users experiencing Dolphin freezing up when cut and copying use the following link to update dbus-1:
For 64-bit users: http://download.opensuse.org/reposit...7.1.x86_64.rpm For 32-bit users: http://download.opensuse.org/reposit...-27.1.i586.rpm
When I copy files from one partition to another, or from one drive to another, the transfer rates hover around 5-8MB/sec which is kind of slow given that all my hard drives are SATA II. I have the same problem when copying either a single file or a group of files.
I'm running openSUSE 11.2 x64 here (KDE 4.3.5) with three SATA II hard drives that are all formatted with ext3. I have dropped to the CLI and used mv and cp instead - this seems to improve things but I shouldn't have to do this.
I'm not sure wether this is the correct forum for this, but this is the best place I can see at the moment, so I'll give it a try. Please redirect me if I'm mistaken.Running Suse 11.2, I have a RAID-5 device mounted, and a straigt disk. I want to copy data from the straigt disk to the array, using several methods: with Dolphin, with cpio. Copying runs for some time, sometimes one or some files are copied indeed, but after a short time (sometimes half a minute, sometimes 10 minutes or more) I get a
Message from syslogd@linux-wrth at Jan 9 22:44:03 ... kernel:[ 381.602651] Oops: 0000 [#1] PREEMPT SMP Message from syslogd@linux-wrth at Jan 9 22:44:03 ...
I've discovered that Dolphin seems to lose random files when copying many large folders.
I first noticed this a few months ago when I tried to copy my music library from one folder to another on the same HDD. It consisted of around 600 folders and 6500 files. During the copy there were no errors but after the copy I found that some of the newly copied folders were missing files. I put it down to human error or a glitch.
Yesterday I tried to copy 13 folders containing rips of some of my DVDs. Each folder basically had one film of either 700MB or 1.4GB. Again no errors showed up during the copy but I found 3 of the newly copied folders were empty.
It's not so critical with music or films but I can't afford to lose work data like this.
Has anyone experienced or seen a similar problem with Dolphin? I'm going to have to do some more extensive testing but this is not good.
The first time I noticed the problem I was running KDE4.3.4 (I think) and now the latest was with KDE4.4.0.
I get a window that shows a broken image which shifts to the left in bits - top half, bottom quarter, etc. - and the colours flicker wildly in separate parts of the image. The shell from which it was launched gives this output: Any of the controls I try gives me errors, such as:
Set Auto Exposure on error Set Auto Exposure on error Set Auto Exposure on error Set Auto Exposure on error
I closed this program and ran kopete, which showed me no image at all but gave this output on the shell: Calling appendChild() on a null node does nothing. Calling appendChild() on a null node does nothing. Calling appendChild() on a null node does nothing.
How do I edit a file (config file, etc.) in KWrite (instead of VI) from the bash shell?I can't seem to "see" certain files using Dolphin and the only way I can locate/see them is using the shell but I'm a complete VI newb and would rather use KWrite for the moment.
I recently got my D-Link DWA-556 pci card working with my new desktop with Ubuntu 10.04 64-bit. Connection speed is good, but local network file transfer speeds are pitiful. I'm trying to copy some files from my laptop(also running 10.04) and I'm getting around 300-500 kb/s, which is actually lower than my typical download speeds. Anyone know what the problem might be? output of iwconfig is this:
Since I've upgraded to KDE 4.5 on openSUSE 11.3. I am getting some instances of Dolphin hanging or lagging when navigating directories or opening files.
In Dolphin i have build an ssh-Connection to my homeserver. Now when I edit an file, the save to the remote location occures only when the editor is closing.This is for webdevelopment etc. not practical.Which alternatives are possible?(under Windows i love WinSCP )
I have just rewired my LAN using Cat 6 cables. Download- and Upload speeds to my main machine are great :However, it seems my LAN speed is very slow. when I copy large files from my main desktop pc to my mediaplayer, I only reach a speed of 3,7 MB/s in Ubuntu 10.10 using SMB protocol to connect to mediaplayer. I use a Sitecom WL351 Router that works fine as far as I can see. Using my dualboot Windows 7 I can copy the same large files using same setup (same pc to same mediaplayer) I can copy with almost 10 MB/s. I appreciate a little protocol overhead in Ubuntu, but this seems to be a little too much
When i try to copy files from my samba server (Ubuntu 9.10) to my windows seven media center, the speed is extremely slow. So slow that is better to download 100mb file from the internet, than from my lan. And on my lan, every card and switch is at 1000 mbps speeds on cat5 cables. And from XP or other linux machine
Few days ago formatted away winxp at office and installed OpenSUSE 11.2. In winxp USB speed was fine (actually full speed of my SDHC card using card-reader), but in SUSE it's about 1.13 MB/s.
The strange thing is - I have the same version of SUSE at home, on both desktop and laptop, with the only difference in kernel - at home both are default kernel, and desktop kernel at office.
Should I try default kernel and is there any way to determine the source of the problem?
Whenever I go into the folders they're stored in and try to open them. They close so fast, in fact, that it's only after switching over to Konqueror that I found the files simply will not open. VLC/Kaffeine appears to load for a few seconds and then closes again without any indication of a bug or problem - it just doesn't work.
Been trying to sort this out for the last two days now, but I'm a complete simpleton with computers/linux and don't know anything about using the terminal, etc. (I can't even install stuff without using webpins) but now I'm stuck and searching around for people with similar problems really hasn't turned up anything that is familiar or understandable.
All of a sudden, Dolphin is identifying .xls files as "OLE2 compound document storage (application/x-ole-storage)." I searched for xls in Configure desktop, file associations and it still appears as application-vnd.ms-excel. It does not appear as x-ole-storage.
Other spreadsheets (ods, xlsx) are still identified correctly and open automatically in the proper program. This is a new behavior, and I'm assuming it has to do with something I updated in Yast. I'm using KDE 4.6.2 under 11.4.
As a workaround, I added the .xls extension to the file association for x-ole-storage, which allows Dolphin to open the file automatically, but it still asks me to install software to handle the file type. I answer no and then the file opens in Libre Office.
Before adding .xls to the file association, I tried to get this to happen automatically by going through the open with other application menu and checking always use this application. This had no effect.
i'm used to copy dvdvideo from k3b and it always worked.But I got a dvd that was readable from dolphin (AUDIO and VIDEO folders) but when I tried to copy the dvd from k3b , it could not.I then copied the audio and video file and created an iso and burned it.My problem is that mplayer could play the original dvd but not my copy of the dvd either as the iso or on the dvd itself.
Every time I try to empty the waste bin I get dolphin error - 'The file or folder /.local/share/Trash/files/IMGP1676.DNG does not exist'I tried to recreate the file 'IMGP1676.DNG' , deleted it i.e. sent i to the waste bin and then tried the empty waste bin again, although this time it was there and deleted it still reported the same error.du -h .local/share/Trash/files/ 12K .local/share/Trash/files
I don't know where to begin figuring this out. On a total fresh install of kubuntu 11.04, everything went fine. When I do any copying in dolphin it crashes. Konqueror does the same thing. I installed samba and I can copy files when using samba from a remote computer, locally it crashes dolphin and konqueror. I turned off desktop searching, still crashes. I tried copying from konquorer to dolphin and vice versa, crashes everytime. The system notification acts like it started the copy and keeps whirring until I close it. What can I try?
my context menu in dolphin/konquerer is very slow -- 2-3 seconds to pop up.I have a dual core 1.4ghz pc, so pc speed is not an issue.My cpu pins during the delay that the context menu takes to pop up. I ran valgrind --tool=callgrind dolphin and attached the two files that it produced.I viewed them in kcachegrind but i dont know what to make of the data.
i am using dolphin 1.5 in kde 4.5.2. whenever i try to access movie file from remote samba server. dolphin copies the movie file to somewhere in local hard disk. so, i have to wait until a big file transferring complete. i know that it happens when i open .avi using mplayer. if i open the same remote file with kmplayer, it will player immediately instead of making local copy first. however, kmplayer is very slow and sounds and video stream breaking up, (i am sorry i do not know right english expression for this) i suppose this is not related to mplayer configuration. this seems to be dolphin problem. can i make dolphin to stop copying samba share to local disk and play instantly? there is a video in videos. it is comparing how dolphin and nautilus act differently when i play remote samba share movies.
I need to copy my music to a portable HDD in alphabetical order. My headunit in my car will only display the folders and files in the order that they were written to the disk so to have any form of logic to the album / track listings they need to be written to the disk in alphabetical order.
how to do this in openSUSE? I know dolphin doesn't do this.
I have an external hard disk with lots of big files and a lot of small matlab script files .m.I would like to grab all the files inside that harddisk that have the .m extension or the *.mat file extension (both are matlab files).Of course this is a -first-find the *.m files script and -then copy the files into the hard disk.What I do not know is how I can also keep the structure of the folders containing the *.m and *.mat files when I will copy them in my local hard disk.As this external hard disk contains 2TB of data it is not possible to copy all the files first and then remove the unnecessary.So I have to find and copy only the files I need but with also keeping the tree structure that the external hard disk has
inside my Linux I am using virtual box to launch windows xp. I have one shared folder between the operating systems so as to share my files As I can not trust virtual box and windows xp... can you suggest me an easy way to take daily backups of one of the folders I have inside that shared folder?The files are mostly html files so the file size is not so much of a problem (at least I think!)How can I take daily backups so to not lose something?
