i am running on suse 11.3 on a laptop i missing the wireless under network it said not connected i done everything that is writte n i have acer aspire 5742 intel core i3 370m
[Code]...
I've got a computer with a Netgear WG111 wireless dongle, however I don't have the setup CDs and I don't know how i'd get it working in 10.10 anyway.
View 3 Replies View Relatedso i have most recent ubuntu server installed (10.04 i believe) and currently i have a usb netgear WG111 v3 plugged into my computer server. However it does not supply internet. I was told to edit the /etc/network/interfaces file and put in
Code:
/etc/network/interfaces
auto lo wlan0
iface lo inet loopback
iface eth0 inet dhcp
iface wlan0 inet manual
wpa-roam /etc/wpa_supplicant.conf
wpa-roam-default-iface wlan0-default
iface wlan0-default inet dhcp
[Code]...
but i have no idea how to edit it properly let alone, And this assumes your wireless NIC is already supported and visible as wlan0. Could someone help me or perhaps walk me through the process to correctly set it up so i don't have to bridge my connection from my laptop please?
Lucid i386 Dell inspiron 1525 with 4695agn, iwlagn driver Just installed a new router, Netgear WNDR3700 Old inspiron laptop with Hardy installed connects fine to G wireless An Acer with Vista connects fine to G wireless My Inspiron with Lucid connected fine until I enabled WPA on the routers 5Ghz band. At that point I couldn't connect on any, 2.4 Ghz no enc, or the wired connection. The Windoze pc was connecting fine. Fired up the old Hardy laptop and it connected fine.
Now here's the weirdness!! As long as I had the Hardy laptop connected either wired or wireless, I could connect to the router with the Lucid laptop to unsecured wireless or wired. Soon as I turned off the old Hardy laptop, my Lucid machine could not connect? WTF? I then disabled security on the router and I could connect with my Lucid machine?
I have managed to setup ndiswrapper and am able to see my wireless network but cannot connect to it.
I am using NDISWRAPPER and a Netgear WNDA3100 driver (I think this is Atheros-based) to connect through a Netgear WN111 USB Wireless dongle to my existing wireless network. I am running 9.04 on a Fujitstu-Siemens laptop.
I am aware that the WNDA 3100 driver is not the intended driver for my WN111 dongle, but it is the only driver that showed "hardware present" when loaded. All others (I tried perhaps 5 or 6) showed driver installed but no info about hardware.
When I try to connect to the network it tries for a while, occasionally prompting me for the passphrase, and then eventually stops.
I would like some help figuring out what else I need to do. I feel I am nearly at the solution. My guesses are as follows (for what they're worth):
1. Could it be something to do with the WPA security?
2. Could it be something to do with this, output from dmesg?
Quote:
[ 20.737363] ADDRCONF(NETDEV_UP): wlan1: link is not ready
3. Could I need to set some further parameters in the network manager?
I have an Atheros ar2427 chip in my Asus EEE 1001P and I'm using WICD to configure it. I can scan for wlans, but I can not connect. I installed the compat wireless package from yast and I downloaded the source from the compat wireless site and tried to compile it (which seems to be the solution for Ubuntu) but I got an error and an interesting warning
Code:
Linux linux-0yl2.site 2.6.34-12-desktop #1 SMP PREEMPT 2010-06-29 02:39:08 +0200 i686 i686 i386 GNU/Linux
[code]....
I have an Ubuntu 10.04. It connects perfectly with a Netgear wireless to the internet at my work place. But i cant connect it to my home Netgear network. It connects to the router. Receives IP address. But no internet. But I'm able to connect to internet using ethernet. I'm also able to connect to internet wireless in my Windows.
View 5 Replies View RelatedAfter having scoured the internet and the forums for advice, I am still not able to connect via Wireless, which is being controlled by Network Manager.The following is info I obtained from running a script that I obtained reading these forums:
* Hostname: linux-8qpz.site
* Run date and time: Sun Oct 24 10:12:58 EDT 2010
---------------------------------------------------
[code]...
Im a Linux newbie and am running OpenSuse 11.3 (Gnome, 2.6.34.7-0.5-desktop Kernel) and Ive an Asus N13 wifi dongle (linux compatible). I currently connect using my laptopś internal wifi but I bought the dongle due to trouble with weak signal. It came with some sort of code that can be "compiled" but I havent got a clue how to do that (and I have been researching this matter for quite some time now). I then came across a post where someone with the same USB stick created and added only two small files to his filesystem and it worked...for him (maybe becasuse he was on a different Distro )
Ralink RT2870 USB Stick and created the two files mentioned in the post (network_drivers.rules and network_drivers.conf) and placed them in ETC... etc, etc! I rebooted the system but NetworkManager only lists it as "device not ready" ... So now back to square one.
[Code]...
wifi card:atheros ar5007egOS: openSUSE11.4My laptop can't connect on network after system hibernate. It has been asking me for enter the wifi password. But when I input the wifi password it still can't connect on network. I have to reboot it.
View 3 Replies View RelatedI recently got a lenovo w510 laptop and I installed openSUSE 11.3 KDE on it. the wireless works fine at home (802.11g WPA2) when I go to work I have tried to set up the wifi for the 802.1X PEAP network but it doesn't look like it even tries to connect.
The work network set up is as follows. non-brodcasting SSID (do I need to tell network manager of this? I manually enter the SSID no problem)
Dynamic WEP 802.1X
PEAP
blank anonymous identity
no CA cert (I suspect this might be the problem)
PEAP v 1
MSCHAPv2
I have verified my username and pw several times, as well as the SSID. Just yesterday I helped a co-worker get on the network under ubuntu and it worked like a charm.
The Hardware profile displays the wifi card as a "WiFi Link 6000 Series" It is an intel card.
I moved to Berlin recently and I got wireless internet through an access point. I'm supposed to use the laptop's built-in wireless netcard to access the internet. This usually works in windows (connection falls out from time to time), but I have yet to make it work in linux. I'm using OpenSuse 11.3 64-bit and the Knetwork manager. Most of the settings in the network manager are correct, but it keeps wanting to use system certificates for the server. By that I mean it keeps checking 'Use CA System certificates'.
So I can't choose the CA-certificate supplied by my internet provider. I keep removing the check-mark and pointing it to the 'hotzoneCA.der' certificate. I also got a 'personal' certificate, in lack of a better word. Its called 'jacob_collstrup.p12'. The Knetwork manager seems to accept the 'jacob_collstrup.p12' certificate, but not the other one.
I just put the certificates in a folder like this /jacob/home/hotzone/zertifikate/ I can see the network fine using the Knetwork manager, and the signal strength seems ok. Not too good, but it shouldn't be a problem. I might have messed up the system, since I first tried this guide, prior to experimenting with Knetwork Manager:
1. (had to run this one as su)
Code:
wpa_supplicant -w -i wlan0 -c /etc/wpa_supplicant.conf -Dndiswrapper -dd �t
2. (This was supposed to be put in a wpa_supplicant.conf file)
Code:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
opensc_engine_path=/usr/lib/opensc/engine_opensc.so
pkcs11_engine_path=/usr/lib/opensc/engine_pkcs11.so
pkcs11_module_path=/usr/lib/pkcs11/opensc-pkcs11.so
[Code]...
I have only had a few weeks worth of experience with linux, so I'm probably considered a newbie at this but I felt like giving it a shot. I just configured my new Toshiba Satellite A505-S6969 to jaunty. Most of the transition is going well but I'm stuck with a few issues, one of which is getting my wifi to work. Right now I'm working off of an ethernet cable.spci returns
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port
[code]...
Been doing some reading here and needing some help since all the forums here isn't for 11.2
i have the above mentioned usb wireless device and have downloaded the firmware and have renamed it now i need to know is where to put the firmware and get this wireless to work i hate the cable stretched across the
I have problems connection my wg111v2 to my AP. I am running opensuse 11.2 with kernel 2.6.31.12-0.2 The AP itselfe is working fine - as I am using it to access the inet with it from my laptop. However I also tried different channels and encryption schemes with no result. But with my Desktop it is really strange. When I boot up it seems as if I have a connection for a short time (I can start loading a webside but it will stop in the process before it is finished). I have searched for similar problems and found this post: Netgear WG111v2 RTL8187 - openSUSE Forums but some things are different: but I thing the comand line output will tell you more than my talking...
My device:
Code:
linux-tn7m:/home/ava/sourcecode/rtl8187L_linux_26.1039.0104.2010.release # lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 0846:6a00 NetGear, Inc. WG111v2 54 Mbps Wireless [RealTek RTL8187L]
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[Code].....
I'm having trouble installing my wireless card drivers. I've read a lot on this using Ndiswrapper to install my drivers but when I go to install I get this.
linux-8h6g:/wg311 # ndiswrapper -i wg311v3.inf couldn't open wg311v3.inf: No such file or directory at /usr/sbin/ndiswrapper line 219.
I'm giving the right path to the inf file tried moving to other folders and still nothing.
Above adapter can be installed on v10.2 and 11.3 using ndiswrapper:-
1. Copy the 3 driver files from Windows:- like netwpn111.inf, WPN111.sys & ar5523.bin.
(Be carfeul about the exact names, because they have changed over time).
2. sudo ndiswrapper -i netwpn111.inf
3. sudo ndiswrapper -m
4. sudo modprobe ndiswrapper (the adapter should light up at this point and networks will be detected shortly after - see network manager). (Be careful of paths here - e.g. I had to use /sbin/modprobe - so 'whereis' may be necessary to find these commands).
2nd When I reboot, I need to run the modprobe command again. How do I make the module load automatically on boot? Also (and this is minor), can I bypass the KWallet, keyring thing? it seems silly to enter a password for the keyring and then click another password dialog, when I can just as easily enter the password for the network itself.
When i click the networks icon on the toolbar, these options popup:
Wired Network - (disconnected)
Wireless Networks (device not ready--firmware missing)
VPN Connections
I can click VPN connections and that's it. How do i get the firmware needed to connect to a wireless network?
It's tooken me this long to get Ubuntu and now I can't connect T_T
lspci | grep Network
Quote:
04:00.0 Network controller: Intel Corporation Wireless WiFi Link 510
uname -a
Quote:
Linux ubuntu 2.6.31-22-generic #68-Ubuntu SMP Tue Oct 26 16:37:17 UTC 2010 x86_64 GNU/Linux
[Code]....
Tried this to enable the wireless
ifconfig wlan0 up
Using an old (5 year) laptop with XP loaded I installed wubi to save altering partitions etc. It all downloaded fine and connected to the internet by wire. I set up the wireless connection using WPA but could not connect. The wirelsss card does see my network and others. After lurking around the forum and trying various things I found that I could connect without encryption. The more I read the more I became confused.
Anyway what I could glean about my Wireless Card it is a Intersil Prism2 mini usb adapter - but also shows up as an Acer ?? Warplink 802.11.
Using lshw I found this reference to wireless
I became even more confused and got a bit lost using the various codes in the terminal and looking up things about drivers etc but would like to persist.
I have 10.04 lucid installed on a presario 2800t laptop(it's old and hasn't got much memory). Anyway, now I can't get my Netgear WNA1100 to work. I know it works right away with 11.04, but that isn't really an option for me. It's too slow on this old computer. get it working with 10.04?
View 9 Replies View RelatedI have a Netgear WG111v2 Wifi dongle, sadly there is no linux drivers for it. The only solution i can find is to use Ndiswrapper.
Will it be a major challenge writing a Linux driver ?
Where should i start ?
NB. I want to write my own driver for the following reasons:
Get a better understanding of Linux Device drivers. Probably, get a better understanding of C/C++ and Linux in general.
My wireless card is:
Code:
03:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1000 [8086:0083]
On Fedora 15, when I boot kernel 2.6.40, my laptop is unable to connect to my wireless-G AP. dmesg shows the following:
Code:
[ 43.866090] wlan0: direct probe to 00:27:19:14:c2:ca (try 1/3)
[Code].....
It works fine, however, when I boot using kernel 2.6.38 (from which I am posting) and in Windows. Also, I found some emails from the linux-wireless mailing list which appear to be talking about the same problem.
The system is fully updated. I've tried the 11n_disable=1 hint I came across on the ThinkPad wiki, but it didn't help. (I'm on an Asus K42Ja, in case it's relevant)
Although I'm fine with staying at 2.6.38 for now, are there workarounds/fixes for this?
Okay I've got a Netgear N-150 WNA 1100 USB WiFi adapter, it doesn't work in Ubuntu it's not supported. There should be a way to make it work with ndiswrapper. I tried and failed before and due to other non related circumstances I had to reinstall Ubuntu. What are the steps to install ndiswrapper and it's dependency's on a fresh Ubuntu installation that cannot connect to the internet.
View 9 Replies View RelatedI already have a wifi card- the netgear wg311v3. that had almost NO linux compatibility, so I won't make the mistake of buying any old wifi card again. What I want to know is, what's a good wifi card for Linux. Here are some requirements I have for it:
Preferably 802.11n support, but I could settle for "G" Out of the box support. As in, I don't have to use Ndiswrapper. Just pop it in, and let ubuntu do the rest I would prefer a USB based dongle, but PCI would be good too. I don't have any brand preferece.
When I select the wifi icon on the panel, it just shows "No network devices available". I know my network can be found when I search with my iPhone, so I know there are networks to connect to. So, I checked the drivers, and it informs me that the B43 and STA drivers are not activated. So thats not a big deal, I guess, but when I use my ethernet cord, my laptop doesn't recognize/acknowledge (I'm not sure what the right term would be)it. I'm fairly sure I can't activate these drivers without an internet connection because when I do try, a message pops up saying "failed to fetch" with some long link.
My only guess is that it could be a hardware problem, but I really have no idea. I guess the ethernet problem is my only real problem. Because after I establish and internet connection the the rest is easy to fix.I'm sure its obvious, but I'll go ahead say that I'm a novice ubuntu user. I've only been working with it for about a week, but I'm learning alot.
I just installed 9.10 and I can't detect any wireless networks. Is the card compatible with 9.10? Do I need to install any drivers? If the card isn't compatible with 9.10 is it compatible with later versions of Ubuntu? Marking this as somewhat urgent as I need to get internet access for some coursework soon, and also because my parents will kill me if they find out I've done anything unusual with the laptop because it's new and they think anything non -MS is a virus.
View 9 Replies View RelatedRT2500 wifi card could not connect to wireless router using WPA personal.OS - RHEL4; Dell Inspiron C600; interface detected ra0
View 12 Replies View RelatedI have a telephone connection of 1 mega internet modem huawei mt 880 SmartAX my desktop computer is connected via an ADSL PPPoE.I use Ubuntu 10.04 in Spanish and want to know how to connect a WiFi router TP-LINK TL- wr942nd to provide wireless Internet to other 2 PC, a desktop with a plaquet wireles G CNet CWP-854 and 500 series notebook olivetti olibook. The issue is that when I connect the router I can not even go online and do not know how to operate the network, I can not even connect the desktop to my internet provider
View 1 Replies View RelatedWG111v2 USB that works just fine on my Ubuntu 12.04 Dell can't connect on my Debian Gigabyte. It finds the network name just fine, remembers its password, and tries to connect 3 times before giving up. This tower is 4 days old, as is the OS.
View 1 Replies View Related