In previous releases 11.2 and lower it was possible to load the dummy network module using modprobe dummy0. But this module is not available for 11.3. So how to setup a dummy network interface?
View 1 RepliesLast night while setting up wired & wireless connection in openSuse 11.2 Gnome version via YAST's ifup, I got wireless but lost wired connection (interface eth0). Dmesg shows that eth0 became eth1. I cannot get eth0 back. Is there any way to remedy this situation, eg. get info from the Ubuntu partition in my triple-boot laptop, without having to re-install openSUSE?
View 3 Replies View RelatedI would like to use zypper to update openSUSE 11.2 through the Virtual Terminals (tty1 thro' tty6).
Network Interface is wlan0 (Wireless LAN, home network through a Router) that requires a password using WPA2.
My question is how to start wlan0 through the command-line ?
Im trying to setup multiple domU through the default bridge setup. I am able to access only one of them through the network at a time. If you ping one of the domU it works perfectly but you cannot ping any of the others until you stop pinging the one and even then it takes a bit before you can. Ive looked around for a while and seen similar problems but nothing ever seems quite the same. Im probably missing something really stupid. Or is this the way the bridge is supposed to behave? Do i need to use a routed virtual network?
[Code]....
I have a little problem with my Linux Suse 11.2 Server. I have unused network card with one port, and one with 4 ports and two used ports.
so->
eth1 is connected to a dsl-modem
eth2 is connected to a switch
i want my suse server to route between modem and switch.
Somehow, I can't go in the internet via eth1. I have to create a bridge br0 to go in the internet. very strange, when i delete the bridge and set eth1 as primary device, i have no internet.
How can i route from eth2 (10.x.x.x) to (eth1 or br0 (80.109.145.x) to Modem (80.109.145.1)?
how can I go about adding an additional lo interface, like lo:0? I need to create this interface, give it an IP and set it to not arp, so this box can be behind a load balancer. Just copying ifcfg-lo and changing the requisite attributes did not work, got an error saying "Interface lo:0 is not available".
View 2 Replies View RelatedI have a ppp0 entry with post-up options like this
mapping ppp0
map none photon-plus motorola
map timeout: 12
[code]...
I am trying for the last many days to setup my opensuse 10.3 as Samba PDC Server according to the URL mentioned below, but in vain:How to setup SUSE 10.3 as Samba PDC - openSUSE When ever I try to join a Windows XP machine to the domain setup on Opensuse, I get the error:'The following error occured while attempting to join the domain. The network path was not found'. What could be the reason for this error despite of the fact the I am able to ping the FQDN of the PDC from the XP machine, but the XP machine simply denies to join the domain because of the above mentioned error.
View 7 Replies View RelatedI have an opensuse 11.3 install which I want to set up as a network boot server to install Solaris 10 on a Sun Ultra 10 client. According to what I've read, this requires rarpd and tftpd which I've set up on opensuse, but also bootparamd which I can't find for 11.3. It seems it was last included with opensuse 9.2. Does anyone know if it's available, if I could use the suse 9.2 version, or any alternative?
View 3 Replies View RelatedThere is a cable plugged in to the second network card, but that interface is not configured. I'm getting a lotof "martian source" alerts because of this.If the interface eth1 isn't started because it isn't configured, why am I getting these messages?
View 2 Replies View Relatedwhile trying to set up Xen Virtual Nodes we encountered one issue with the network (which is why it is posted here On the DomU the interface is provided by a bonding -bond0- of three NICS. Now the Xen network script a) does not take this bonding b) destroyes even this bonding From a number of posts I assume I have to configure this by hand, correct? Is there an instruction how to do this? Simply create a bridge on top of bond0??
View 1 Replies View RelatedI have 2 laptop with opensuse 11.2. One of them is connected to the Internet through a Mobile Connection with a CDMA/EDVO modem on the usb port. I want to share the Internet connection with the other laptop through the WiFi interface of each of them. How should I proceed?
View 3 Replies View RelatedI'd like to have a set up where my Ethernet card has a static IP set up but my WiFi card doesn't.Currently I have a profile for this set up in Network Manager, however on boot up and every time I replug the cable Network Manager chooses the default "auto eth1" profile. I manually have tochoose my own profile for the Ethernet card every time. How can I make it default??I know the workaround would be to use ifup but then I lose the ability to quickly change access points for my WiFi card so that's not a solution for me
View 9 Replies View RelatedI've just installed openSUSE 11.2, one problem is suse didn't find an internet connection when suse performed the ..."automatic system configuration. This routine attempts to configure your network and Internet access and sets up your hardware"... Where can I manually configure the network. I'm in the network folder now no luck. I've been using every documentation I could find Novell Documentation and DVD installation/11.2 - openSUSE Network Status: Unknown network status
View 9 Replies View RelatedI successfully added/shared a network printer in SUSE 11.3 32 bit, but when I try on the 64 Bit box it didn't work out very well.What ports need to be open ? Is it necessary to open port 631 in YAST->Firewall->Advance- >UDP and IPP ?(TCP 631 already open) What services need to be running? Here is the error log :
[16/Dec/2010:19:25:43 -0500] [cups-polld xxx.xxx.xxx.xxx:631] CUPS-Get-Printers failed: Forbidden
XXX is my server IP
I have a work desktop plugged into the work network. As I opened my firewall settings I noticed that it is turned off. My question is how should I configure it? I saw that the interface isn't assigned to any zone... I should assign to internal zone and open some port that I need in order to work? There are some guidelines for configuring the firewall?
View 2 Replies View RelatedWhere can I find set up information in order to share internet between my Ipod touch and my laptop? Laptop is connected to cable modem and has wifi interface (so no wireless router).
View 1 Replies View RelatedI have installed open suse 11.4, gnome but no luck with wireless settings so far. kernel version is iwl3945 here is stuff that i did but it says "scan is deprecated"
linux-1f6k:/home/rajbanul # dmesg | grep firmware
[ 7.249018] tg3 0000:18:00.0: vpd r/w failed. This is likely a firmware bug on this device. Contact the card vendor for a firmware update.
[code].....
I found multiple sites explaining how to add IPs to a network interface as virtual interface like eth0:0. However I can add IPs to an interface as well using the ip command: ip a a 192.168.2.2/24 dev eth0 What I want to know is how I can make this persistent on rhel/centos.
View 2 Replies View RelatedI am unable to do my network setup. I have a lan connection. I used to easily setup it in windows xp in network connections > internet protocol > properties. But I do not understand anything in linux. I have installed latest version of open suse 11.1 and KDE environment. Secondly I am unable to play mp3 files on it and I do not hear any sound at startup too. I *945* motherboard with a inbuilt realtek lancard and it is working fine on windows.
View 3 Replies View RelatedI have a laptop running 11.2 with an internal Broadcom-based Wi-Fi card that's working fine. I'm trying to get 802.11n going with the WUSB600N. The USB ID on this device is 1737:0079. I believe this means it's a "V2" with an RT3572 chip.
No driver loads for this device when it's plugged in. If I do a "modprobe rt2870sta", a driver loads, and syslog shows "rtusb init" and "usbcore: registered new interface driver rt2870". But ifconfig -a doesn't show a new network interface. I've also tried building the RT3572 driver from the manufacturer's web site. It builds fine, and modprobe will load it, but I get the same results as the rt2870sta driver.
i've just setup a vps server with 11.4 everything is almost look fine now, but i couldn't setup a nameserver, i've searched on the internet about that but directories is different in suse. anyway i registered a domain on onlinenic yesterday and i want to use this domain as a nameserver and my hostname. how can i do that ? and do i need to have at least 2 ip for that ?
View 7 Replies View RelatedI just installed Opensuse 11.2 today and I'm eager to start downloading and customizing, but I can't set up a network. I originally installed it with the GNOME desktop, and when I opened firefox i could only connect to [URL]... and [URL], other websites timed out, even if i got to them via search results or URL.
Now, I reinstalled using the KDE desktop because after a little thought I preferred it, but now I can't even connect to these search engines at all. I don't know how to configure the network! It's through the onboard ethernet port, ethernet cable direct to modem.
I have tried all kinds of DNS services. Like opendns, Google DNS, 4.2.2.x, Scrubit, DNS Advantage.In my experience none of them are consistent enough & there is a fluctuation in their performance.A guy told me to try enabling DNS cashing on my openSUSE box.I don't know much about DNS caching.So, I want to know
(a) Will enabling DNS caching improve my Internet experience ?
(b) Is DNS caching enabled by default in openSUSE 11.4 / How to find out ?
(c) If not enabled by default, how do I enable it ?
I have a printer/scanner/fax that's on the network. i have the printer part set up through cups but how do I set up the scanner? What programs can I use on opensuse to see the scanner?
View 9 Replies View RelatedI have several Windoz machines in a peer-to-peer network and now two SUSE machines, one 11.1 and another 11.2.I have a network printer accessible now to all the machines.My next step is to be able to share files between all the machines and several network drives. I know how to set this up between the Windoz machines, but the only way I can get the SUSE machines to see the network (and be seen) is to shut down their firewalls, and I don't think that's how you are supposed to do it?Can someone point me to what it is that I need to read, or is there a FAQ somewhere to help get me started?
I think that this has something to do with Samba and I installed Samba (client or server? I forget) on the 11.1 and 11.2 seems to have it already built-in, but I don't know how to set it up with the firewalls on the two Linux machines so that it is all seamless (as if anything can be seamless).
My Samba setup works just fine however whenever I do stop/start/restart. I get these errors in the logs:
Jan 17 00:21:14 neutrino smbd[4297]: smbd_open_once_socket: open_socket_in: Address already in use
Jan 17 00:31:20 neutrino smbd[4557]: [2010/01/17 00:31:20, 0] smbd/service.c:1009(make_connection_snum)
Does anyone know what to think of these? My thought is since it works just ignore and probably the SuSE team will get to cleaning this up sometime.
Just loaded Open SUSE EDU L I F E 11.2.2 on a Server and like what I see. The install went well and everything came up fine. I like the look and feel of this distro. The GUI features are impressive. Internet connects via eth1 . Sound, CD/DVD works and plays ok/ , grapics all working. I have two NIC cards installed.I am preparing (learning , testing, exploring) with a number of Servers that I want to take to schools in Africa.One of the key components that I need to get up and working is the LTSP. I was delighted to see that this version includes EASY-LTSP with a KIWI component. [SUSE KIWI-LTSP] So I printed out the LTSP/Quick start/Easy-LTSP (Guide) and tried to set up LTSP on my server.I went to KIWI/Prebuild in the Easy-LTSP presentation page.A box popped up with this info:
Prebuild Images:
IP 10.0.0.254
Interface eth0
[code]....
I am experimenting with Xen with the standard kernel (kernel-xen package) and utilities. I already got bridged setup to work with a single domU, but found out that because of my wireless card I cannot expect bridging to work when connected wirelessly. Now I am trying a NAT setup but I cannot seem to get any network connection from the domU to the dom0 and viceversa. Comparing the network devices and routing tables of others, I cannot see any problem.
The domU runs with IP 10.0.0.1 and the dom0 has a vif with IP 10.0.0.128 with a default gateway of 10.0.0.254. Pinging from the domU to the dom0 and viceversa does not show any traffic at all when I use tcpdump to monitor eth0 in the domU or the vif interface in dom0. It seems that basic connectivity of the vif interface and eth0 in the domU does not work. Any tips on how to debug this problem?
We have installed "openVPN" from openSUSE 11.2 repo and "openVPN - webmin module" (GUI).What it needs to be done .. "Road Warriors" need to be able to access websites through openSUSE box sitting in the data center, from remote locations (hotel, coffe shops, wi-fi hot spots,..)We're half way there but it gets stucked somewhere with the IP's
View 6 Replies View Related