OpenSUSE Network :: Serial Response Timeout With Huawei E169
Jan 4, 2009
I would like to get my Huawei E169 (aka. Vodafone Mobile Connect K3520, E620 etc.) USB UMTS/3G modem running with my openSUSE 11.1 x86 installation on my MSI Wind U100. The GPRS/UMTS connection works perfectly fine with the stand-alone application Vodafone Mobile Connect for Linux. However, there's the drawback that this app overwrites /etc/resolv.conf (leads to DNS issues if I would like to connect via NetworkManager again) and doesn't disable the off-line mode for Firefox automatically. Consequently, I would like to use NetworkManager for the GPRS/UMTS connection, too.
The NetworkManager configuration dialogue (I'm using the GNOME applet) seems to recognize the plugged USB stick without any issues (I get a radio button for "Huawei E620 USB Modem" in the respective add connection wizard). So I've created the configuration for my provider and saved it. After that I've tried to connect via the applet. However, approx. 2 seconds after I selected the connection, the applet says "Network disconnected" (German: Netzwerkverbindung getrennt) and the stick also obviously doesn't get connected (visible via LED). I created several new connections with different names, replugged the stick, rebooted with and without the stick plugged, but without any success. I also installed the special RPM package which is recommended in Huawei UMTS USB Stick - openSUSE, but - of course - the corresponding 11.1 package. I also used the application manually and got the following result: Looking up for HUAWEI modem and switching modem to BBO 06
[Code]....
Can this time out of the serial command be the reason for the unsuccessful connection? And if yes, how can I force the system to wait longer here? Moreover, I'm wondering, that the GNOME NetworkManager applet doesn't allow me to enter the DNS entries for my GPRS/UMTS connection. Where can I add these entries manually or is that not needed?
View 9 Replies
ADVERTISEMENT
Feb 7, 2010
I've just installed openSUSE 11.2 (KDE 4.3) on my Dell 1720 lapcrusher (a fresh install - had no space to install next to my old openSUSE 11.0, so had to wipe that). I have a huawei e169 (e620) that worked fine in 11.0 (after some initial trouble/configuring, details of which I cannot remember) using knetworkmanager, but try what I might in 11.2 I cannot get this HSDPA modem to connect to my ISP (Virgin Mobile Broadband in Brisbane Australia).
I'm looking for some advice on where to start - first up the modem is detected fine in KDE 4.3, I can setup a profile with the correct APN "VirginBroadband" and "blank" inserted for username/password, and PAP enabled and CHAP disabled - thats pretty much how it was setup under openSUSE 11.0, and it will try to connect but always will not authenticate - I'm not sure at which stage of authentication the process goes pear shaped. I've tried different combos of turning on/off compression/echo options etc, turning on/off MSCHAP/MSCHAP2, but to no avail.
View 9 Replies
View Related
Dec 22, 2009
I've just installed Open SUSE 11.2 on my acer travelmate 250 laptop. Everything seems to work ok, it starts and shuts down without any complaints. I inserted my Huawei E169 USB modem to connect to my Mobile Broadband account and discovered a new icon appeared in the system tray that looks like a mobile phone. So i started messing around with its setings but do not seem to be able to get the think to work.
I'm with virgin mobile broadband in Australia, i've checked their website and the APN is virginbroadband and the username and password are both: blank However it still will not connect.
View 2 Replies
View Related
Nov 26, 2009
I am trying to get a Vodafone USB modem to work - Huawei K3765 (which is a rebranded E169). It's supposed to be recognized by the kernel and just added through Network Manager, but - no luck. I also installed vodafone-mobile connect from here: [URL] (as well as the other packages). What happens when I start it - it doesn't see the modem. It's seen as a CD drive, and clicking "eject", "unmount" or "remove safely" on it doesn't help - it disappears, then several seconds later appears as a CD drive again.
View 14 Replies
View Related
May 2, 2010
Connection is possible only after few reboot. Preferences I tried all.
View 9 Replies
View Related
Dec 26, 2009
I have a little bit of a prediciment with my Mobile Broadband dongle, even though I know I'm in a 3G area (Dongle Supports 3G connection) my internet still loads at the normal GPRS speeds max of 5kb/s. Is there anyway to change the speed of it or do I have to keep with GPRS at the moment?
View 2 Replies
View Related
May 17, 2010
I am facing issues on few machines but rest all are ok. They have the same config but I don't know what is wrong. I tried as much as I could but couldn't fix it. Here is the rpms installed on this client
[code]...
The same config is working for all clients but have problems with few machines. May be I am doing something wrong in config or testing at very basic level.
View 1 Replies
View Related
Oct 19, 2010
i have this EM in /var/log/messages:
Oct 19 10:37:38 hoofdkwartier named[319]: client 192.168.66.201#37490: RFC 1918 response from Internet for 107.20.10.10.in-addr.arpa
I tried al lot of things trying to get rid of this, including blocking the host with denyhosts, removing it from dhcp.leases and adding entry's in /etc/named.conf,
following instructions I found on [URL]
Other info I found on the internet are too complicated for me.
We are running an OpenSuse 11.1 server, clients are both Linux and Windows
machines.
View 4 Replies
View Related
Mar 17, 2010
My machine is running on a dual-boot Windows Vista/openSUSE 11.2 scenario. I have been trying to get my Huawei E1550 to work on Linux for the past few days trying numerous methods suggested in other forums from people with the same problem, but I have not produced any fruitful results.
Plugging in the USB modem results in Linux detecting it as a CD-ROM. I have installed usb_modeswitch in attempt to switch it to a modem, but Linux still fails to recognize it. Windows Device Manager and lsusb both give ProductID=1001 and VendorID=12d1 connected to USB1. I'm guessing since Windows detects the correct IDs, the Linux versions should also be correct. In any case, I ran usb_modeswitch with the Default IDs for /etc/usb_modeswitch.conf, which gave 0x1446 as the ProductID, not 0x1001. Upon running usb_modeswitch, the product ID could not be found so the program fails and quits asking if it's connected (and it is).
Just to test, I also ran wvdial which unsurprisingly did not detect the modem and could not send the init strings. All commands were done using root privileges. Also note that when after usb_modeswitch is run and upon plugging in the USB, NetworkManager pops up near the tray saying "attached" but still shows the device as a CD-ROM.
View 5 Replies
View Related
Sep 3, 2010
Although my Huawei e200 usb stick is working well under ubuntu, its not working in openSUSE. I think the udev rule provided by the vendor is suited for a debian system and not for openSUSE. When i see the dmesg output, it adds driver for ttyUSB0 and as soon as it adds it also removes it. This sequence goes on continuing till i unplug my usb stick from my computer. The udev file(78-haier.rules) provided by the vendor is as follows:
ACTION=="add", SUBSYSTEMS=="usb",
ATTRS{idVendor}=="201e", ATTRS{idProduct}=="1008",
ATTRS{bNumInterfaces}==" 1",
RUN:="/usr/sbin/haier.sh 201e 1008"
ACTION=="add", SUBSYSTEMS=="usb",
DRIVERS=="option",
ATTRS{bInterfaceNumber}=="00",
SYMLINK="ttyMODEM"
The haier.sh script that the udev runs is as follows:
[Code]...
# may not use this driver if the product id is already compiled into another driver modprobe -a option echo "0x${VID} 0x${PID}" > /sys/bus/usb-serial/drivers/option1/new_id
View 2 Replies
View Related
Oct 5, 2010
I am trying to connect my huawei e160 usb modem but it keeps failing and does not show on the Network Manager, checking on /var/log/messages this it what I get:
Oct 5 15:31:30 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:30 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
Oct 5 15:31:33 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:33 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
Oct 5 15:31:36 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:36 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
View 9 Replies
View Related
Mar 26, 2011
I have a 3G modem Huawei e173s-6, the usb id is 12d1:1c0b. It's only detected as storage, not as modem. According to some tutorials I've found, I had to use usb_modeswitch and udev rules to make it automatically switch to modem mode, and usb id 12d1:1c05. I followed the tutorials, and the usb changes the id, but after the switch it is still recognized only as storage.
I have the suspicion that I have to add the driver to the kernel, since this is 11.3, but I haven't the slightest clue what to do. Does someone have experience making this modem work in 11.3? tutorial: USB_ModeSwitch ~ View topic - Huawei E173s working config
View 4 Replies
View Related
Jun 19, 2011
I am new to Linux and opensuse is lovely to me . However i have a problem, I dual boot windows and OpenSuse 10.3(because it plays mp3 out of the box) I actually tried newer versions but the problem is that I cant install this Huawei E1752 usb modem. I have failed people. Please help me. I need to use it for internet.
View 1 Replies
View Related
Dec 23, 2009
What include support a driver for USB modem Huawei E219 (HSDPA/UMTS) and Huawei EC226 (3G/EVDO)?
View 1 Replies
View Related
Jun 4, 2010
I tried to connect to the huawei cdma EC325 modem. using the network manager applet. System asked which tpe of connection i selected cdma and gave the username and password for the account and the password for my opensuse account.Still i cannot connect to the internet using huawei ec325 modem.How to rectify the problem What shall i do next.
View 2 Replies
View Related
Aug 31, 2010
I upgraded from 11.2 to 11.3 and with great disappointment I discovered that my HSPA modem, that worked out of the box under 11.2, work no more. At the first attempt NetworkManager is able to build the connection, I am able to use Yast to download new packages and online updating but at the first use of firefox the internet connection hangs up. Any attempt to disconnecting/reconnceting the usb stick gives the following error in the kernel echo:
[Code]....
View 2 Replies
View Related
Feb 5, 2010
I was absolutely dazzled, but my wife made me drop it after 20 days of not being able to get an internet connection.
I thought of trying again after so long to see if things had become easier for every Argentina user who has a Huawei connection (more than half of the country).
Unfortunately not.
The problem is the following:
I have a Huawei SmartAX MT810 usb-modem/router. In order to establish a connection, I need to run the following commands AS ROOT (which is why I cannot use a simple kde autostart bash script)
Code:
modprobe br2684 ; br2684ctl -c 0 -b -a 0.33 ; ifconfig nas0 up ; pppd call adsl
What's more, these commands cannot be run before the modem is operational, since they will end with an error.
In other distros I used to place these commands in /etc/rc.local. I tried placing them in /etc/rc.d/boot.local , but with no success: they are executed before the modem is operational.
In my complete ignorance of all things computer-related I thought it would be a good idea to place a caveat before the execution of the commands:
Code:
READYorNOT=$(dmesg | grep "modem operational") ; while [ "$READYorNOT" = "" ] ; do echo "Modem not operational" ; done
As a result the whole boot sequence gets stuck until I hit ctrl-c.
View 8 Replies
View Related
Aug 5, 2010
I can not get NetworkManager to handle my Huawei E220 usb modem. I have searched forums and tried a lot of things. I have just upgraded from openSUSE 11.2 to openSUSE 11.3 using zypper. It seems to work fine except that umtsmon stopped to work, so for now my laptop has no connetion to internet at all. Here are some information about my settings:
I have used usb_modeswitch to make the device a modem. Am I right if I say that usb_modeswitch is a one time command, or does it swap the setting each time it is called? Anyhow lsusb states that the device is a modem. (All the time.) code...
View 7 Replies
View Related
Oct 16, 2010
i tried to connect whit this key on opensuse 11.3 but i can't the device is recognized i start to connect it and the system show me "activating" but the light never comes blue , it's always green and it's impossible go to internet i use kde..
View 1 Replies
View Related
Jul 25, 2011
I have a problem with trying to connect to VPN over linux. From OSX and Windows the VPN connection goes through fine. It was working flawlessly, for the last one month I never used the laptop or the VPN, however after booting recently 1 week ago the VPN always show as timedout. Some details about the vpn / pptp connection details:
[Code]....
View 8 Replies
View Related
Jul 9, 2010
I have a weird problem on my laptop. Everything works okey on PC though.
I'm using kNetworkManager on my OpenSuse 11.2 on PC.
Everything works fine there with the following settings:
1. Make a new GSM Connection in kNetworkManager and enter settings there
2. Edit etc/sysconfig/network/config file and set .....DNS_Policy from "auto" to ""
3. Enter openDNS to /etc/resolv.conf (nameserver xxx.xxx.xxx.xxx)
It works like that on my PC.
I did the same on my laptop. The modem connects fine, but the DNS'es ain't resolved. So skype etc will work, but no pages will open in Firefox for example.
What else should I need to do to make this work?
It's weird it works the SAME way on my PC, but doesn't on my laptop.
View 3 Replies
View Related
Aug 11, 2010
I have opensuse 11.1 Gnome on Lenovo S10e. I'm wanting to establish a mobile internet connection. I have tried so far...*UMTSMON but when I click on it nothing happens. I have reinstalled the program several times to no avail. *WINE to run the Optus program, however the program doesn't find the HUAWEI USB stick & *Via a Bluetooth connection (use mobile phone as a modem) didn't work either Anyhow, I have tried these and some other ways to get mobile to no avail.
Also, have gone to network connections-mobile broadband-add-configure it- but what am I forgetting to do? Need a path I can take to get mobile internet working. (I even have a direct SIM card slot in this laptop
View 5 Replies
View Related
Mar 15, 2010
I have a DSL brodband connection. The internet connectivity was working fine but lately, I am am facing problems while connecting to internet.Upn connecting the cable to the eth0, the /var/log/messages shows repeated instances of:"kernel:corrupted packets received"Also, if i use pppoe-dicovery, I get " Timeout Waiting for PADO packets" error.There is nothing wrong with the cable. If I connect the cable to a windo$s xp laptop, internet connects fine without any problems.Any idea what could be going wrong? Since the internet was working fine earlier on my opensuse box, im not sure what could have gone wrong with the settings.
View 5 Replies
View Related
Mar 28, 2010
On a small network i have 3 WinXP computers and i've just installed a two new ones with Win7 pre-installed. As server i'm running OpenSuSE 10.3 and Samba with only one share. As i mount it to WinXP computers all get same volume serial number:
Code:
V:>dir
Volume in drive V is AppDrive
Volume Serial Number is 8CD5-975C
...and all Win7 computers get a diffrent one:
Code:
V:>dir
Volume in drive V is AppDrive
Volume Serial Number is A0D3-975C
We use application witch somehow only works when one/same volume serial number on a mounted drive is used.
View 1 Replies
View Related
Feb 21, 2011
im on node1 when i type the command ssh node2@ip the terminal hangs up a bit then an error message stating that connection timeout but here is a thing: i cant ping to node2
but i can terminate the ping manually using ctrl+c when i terminate the ping usual message appears stating 10 packets transmitted, 100% loss
ps: when i go to node3 and ssh to node2 it works fine and also i can ping from node3 to node2 very fine. and the firewalls are down at all nodes -all wired connection over a switch
View 6 Replies
View Related
Aug 19, 2010
icmp request from an ip that is in the same network as one of the local interfaces is not responded to, if the ping request is received via an interface in a different network. Is this some security feature?
Consider the below network
x.1|RTR1|-y.1---------y.2-|RTR2|-z.2------z.3-|LNX|-x.3
RTR - Router
x.1 -> 192.168.x.1
LNX - Linux machine
[Code]....
View 1 Replies
View Related
Mar 14, 2010
I've noticed over the past few months that my internet connection speed (D/Ls, browsing) are getting incredibly slow, but only on my linux box (my laptop, for instance, is fine - in fact, I'm dual-booting with WinXP and it isn't happening there, so I think I've managed to narrow it down to the OS alone):
View 8 Replies
View Related
Aug 4, 2011
I set the default os to boot as windows 7 with a timeout of 1 second. I thought that this would be enough time to switch os ubuntu when i need to, but I am unable to. How can i reset the timeout to 3 seconds? I also cannot view the ubuntu partition within windows because of ubuntu's file system.
View 9 Replies
View Related
Jun 2, 2010
My local area network is always time out for few seconds.I have check my memory with "free -m"There are still left 200+ mb left.I am hosting my own ubuntu server, and I share the same internet line with my server and pc. when I access to LAN, I need to type 192.168.2.2, at outside I can access to [URL]It is only the LAN access timeout, but when I access at outside, I didn't face this problem at all.
View 1 Replies
View Related
Jul 19, 2011
when I try to access any page even small html pages it stays like 3 seconds in HTTP request sent; waiting for response. state..even when I use Lynx locally on the server..bypassing any possible network issues..logs dont show a thing..the server itself is a high end server with nothing running on it apart from apache which is not serving anny clients now, firewall is disabled and hostnamelookups are set to OFF.
View 1 Replies
View Related
