OpenSUSE Hardware :: Huawei E169 Messing Around With Its Settings
Dec 22, 2009
I've just installed Open SUSE 11.2 on my acer travelmate 250 laptop. Everything seems to work ok, it starts and shuts down without any complaints. I inserted my Huawei E169 USB modem to connect to my Mobile Broadband account and discovered a new icon appeared in the system tray that looks like a mobile phone. So i started messing around with its setings but do not seem to be able to get the think to work.
I'm with virgin mobile broadband in Australia, i've checked their website and the APN is virginbroadband and the username and password are both: blank However it still will not connect.
View 2 Replies
ADVERTISEMENT
Feb 7, 2010
I've just installed openSUSE 11.2 (KDE 4.3) on my Dell 1720 lapcrusher (a fresh install - had no space to install next to my old openSUSE 11.0, so had to wipe that). I have a huawei e169 (e620) that worked fine in 11.0 (after some initial trouble/configuring, details of which I cannot remember) using knetworkmanager, but try what I might in 11.2 I cannot get this HSDPA modem to connect to my ISP (Virgin Mobile Broadband in Brisbane Australia).
I'm looking for some advice on where to start - first up the modem is detected fine in KDE 4.3, I can setup a profile with the correct APN "VirginBroadband" and "blank" inserted for username/password, and PAP enabled and CHAP disabled - thats pretty much how it was setup under openSUSE 11.0, and it will try to connect but always will not authenticate - I'm not sure at which stage of authentication the process goes pear shaped. I've tried different combos of turning on/off compression/echo options etc, turning on/off MSCHAP/MSCHAP2, but to no avail.
View 9 Replies
View Related
Jan 4, 2009
I would like to get my Huawei E169 (aka. Vodafone Mobile Connect K3520, E620 etc.) USB UMTS/3G modem running with my openSUSE 11.1 x86 installation on my MSI Wind U100. The GPRS/UMTS connection works perfectly fine with the stand-alone application Vodafone Mobile Connect for Linux. However, there's the drawback that this app overwrites /etc/resolv.conf (leads to DNS issues if I would like to connect via NetworkManager again) and doesn't disable the off-line mode for Firefox automatically. Consequently, I would like to use NetworkManager for the GPRS/UMTS connection, too.
The NetworkManager configuration dialogue (I'm using the GNOME applet) seems to recognize the plugged USB stick without any issues (I get a radio button for "Huawei E620 USB Modem" in the respective add connection wizard). So I've created the configuration for my provider and saved it. After that I've tried to connect via the applet. However, approx. 2 seconds after I selected the connection, the applet says "Network disconnected" (German: Netzwerkverbindung getrennt) and the stick also obviously doesn't get connected (visible via LED). I created several new connections with different names, replugged the stick, rebooted with and without the stick plugged, but without any success. I also installed the special RPM package which is recommended in Huawei UMTS USB Stick - openSUSE, but - of course - the corresponding 11.1 package. I also used the application manually and got the following result: Looking up for HUAWEI modem and switching modem to BBO 06
[Code]....
Can this time out of the serial command be the reason for the unsuccessful connection? And if yes, how can I force the system to wait longer here? Moreover, I'm wondering, that the GNOME NetworkManager applet doesn't allow me to enter the DNS entries for my GPRS/UMTS connection. Where can I add these entries manually or is that not needed?
View 9 Replies
View Related
Nov 26, 2009
I am trying to get a Vodafone USB modem to work - Huawei K3765 (which is a rebranded E169). It's supposed to be recognized by the kernel and just added through Network Manager, but - no luck. I also installed vodafone-mobile connect from here: [URL] (as well as the other packages). What happens when I start it - it doesn't see the modem. It's seen as a CD drive, and clicking "eject", "unmount" or "remove safely" on it doesn't help - it disappears, then several seconds later appears as a CD drive again.
View 14 Replies
View Related
May 2, 2010
Connection is possible only after few reboot. Preferences I tried all.
View 9 Replies
View Related
Dec 26, 2009
I have a little bit of a prediciment with my Mobile Broadband dongle, even though I know I'm in a 3G area (Dongle Supports 3G connection) my internet still loads at the normal GPRS speeds max of 5kb/s. Is there anyway to change the speed of it or do I have to keep with GPRS at the moment?
View 2 Replies
View Related
May 4, 2010
How can I stop Mplayer from messing with my alsamixer settings?
View 2 Replies
View Related
Dec 23, 2009
What include support a driver for USB modem Huawei E219 (HSDPA/UMTS) and Huawei EC226 (3G/EVDO)?
View 1 Replies
View Related
Jul 6, 2010
For a long time, on my netbook Asus EEE pc1000 working fine with my wireless (connecting WEP, WPA). Running with kernel 2.6.29 + rta2860sta v2.2 (package downloaded from the software repository , a user repository)
After somes updates (kernel mainly), all stop working. So I recompile the module v2.2 but don't work. I download from the ralink site the last version , recompile and installed , and appear work fine, but I don't know why the opensuse like to be very annoying and the knetworkmanager don't recognize the device. So , again I download a package from a user repository with the version 2.3 , what appear starts working again. Knetworkmanager recognize the device, but isn't cappable to connect in a WEP network. With WPA works fine.
If I disable the device in knetworkmanager and try configure manually , sometimes work. Probably have some sequence of command what I don't figure out what is. To configure WEP network before this problems I always use only the "iwconfig" command. But I try with "iwconfig" and "iwpriv" and don't work. So , afiter trying a lot of sequence, now I got connected to WEP network, but is very weird how they show this connection,
[Code]...
View 2 Replies
View Related
Jun 11, 2011
one month at this stage and noticed recently that all automatic updates to my system have ceased, so I tried a zypper update from the terminal yesterday and believe it or not I got 1110 updates, about 7 deletions a 3 programs were changing architecture. This went all all day yesterday and finished sometime early this morning when I had to force a reboot as the shutdown button did nothing. After all those updates I do not notice any version upgrades for a few things I checked like Office, Amarok, DigiKAM etc but I am back to a most annoying problem that I had in my first few days i.e. my printer an Epson Stylus Color 760 is totally messing up 2nd and subsequent pages in a printout.
The last time this happened it seemed to sort itself out because deleting the printers discovered and their drivers did nothing. I am sorry to say it is putting me off SUSE 11.4 which I had liked BUT it is so frustating when I can't eben print more than one page correctly. I have come from Windows 7 where these problems did not exist.
View 9 Replies
View Related
Sep 28, 2010
I have a triboot windows suse 11.3 stable and suse 11.3 factory pc, I would like to share the browsers and email settings between the suse stable and factory, I succeed with thunderbird and firefox moving the /home/.thunderbird and /home/.mozilla in an ext3 shared partition and linking these in the respecive /homes, I found that there isn't a /home/.chromium folder, I found probably /usr/lib64/chromium could be the same as /home/.mozilla for firefox, but I don't know if is secure or can damage my system to move this in a ext3 partition and then link this to the respective /usr/lib64/chromium, /usr/lib64/chromium has root owner, root group, visible and modifiable for root and only visible for group and other.
View 5 Replies
View Related
Apr 1, 2011
Is there a way I can save system settings and have yast revert to a config file in case I ever need to reinstall the system again? I hate having to configure the firewall, runlevels, samba shares, samba workgroup, apparmor, and all the other junk after every install. It's not like I install often, but should suse 11.5 or 12 roll out, I'd like it to be a snappy upgrade.
View 6 Replies
View Related
Dec 31, 2009
I installed a new 11.2 and my huawei e1692 isn't recognized, before in suse 11.1 worked perfectly but now not. I also tried installing the software given by the provider that in 11.1 worked, now not.
kde=Versione 4.3.4 (KDE 4.3.4) "release 2"
kernel=2.6.31.5-0.1-desktop
View 9 Replies
View Related
Mar 17, 2010
My machine is running on a dual-boot Windows Vista/openSUSE 11.2 scenario. I have been trying to get my Huawei E1550 to work on Linux for the past few days trying numerous methods suggested in other forums from people with the same problem, but I have not produced any fruitful results.
Plugging in the USB modem results in Linux detecting it as a CD-ROM. I have installed usb_modeswitch in attempt to switch it to a modem, but Linux still fails to recognize it. Windows Device Manager and lsusb both give ProductID=1001 and VendorID=12d1 connected to USB1. I'm guessing since Windows detects the correct IDs, the Linux versions should also be correct. In any case, I ran usb_modeswitch with the Default IDs for /etc/usb_modeswitch.conf, which gave 0x1446 as the ProductID, not 0x1001. Upon running usb_modeswitch, the product ID could not be found so the program fails and quits asking if it's connected (and it is).
Just to test, I also ran wvdial which unsurprisingly did not detect the modem and could not send the init strings. All commands were done using root privileges. Also note that when after usb_modeswitch is run and upon plugging in the USB, NetworkManager pops up near the tray saying "attached" but still shows the device as a CD-ROM.
View 5 Replies
View Related
Jul 9, 2011
I am running OpenSUSE 11.4 on an HP 625 laptop and uses a Huawei EC1260 USB modem to connect to the internet. The configuration on NetworkManager worked prefect and the there is no problem connecting. The problem is when I disconnect the modem manually, I am unable to reconnect it via NetworkManager. I have to physically unplug the modem and insert it again, then only I can connect to the internet again
View 3 Replies
View Related
Sep 3, 2010
Although my Huawei e200 usb stick is working well under ubuntu, its not working in openSUSE. I think the udev rule provided by the vendor is suited for a debian system and not for openSUSE. When i see the dmesg output, it adds driver for ttyUSB0 and as soon as it adds it also removes it. This sequence goes on continuing till i unplug my usb stick from my computer. The udev file(78-haier.rules) provided by the vendor is as follows:
ACTION=="add", SUBSYSTEMS=="usb",
ATTRS{idVendor}=="201e", ATTRS{idProduct}=="1008",
ATTRS{bNumInterfaces}==" 1",
RUN:="/usr/sbin/haier.sh 201e 1008"
ACTION=="add", SUBSYSTEMS=="usb",
DRIVERS=="option",
ATTRS{bInterfaceNumber}=="00",
SYMLINK="ttyMODEM"
The haier.sh script that the udev runs is as follows:
[Code]...
# may not use this driver if the product id is already compiled into another driver modprobe -a option echo "0x${VID} 0x${PID}" > /sys/bus/usb-serial/drivers/option1/new_id
View 2 Replies
View Related
Oct 5, 2010
I am trying to connect my huawei e160 usb modem but it keeps failing and does not show on the Network Manager, checking on /var/log/messages this it what I get:
Oct 5 15:31:30 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:30 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
Oct 5 15:31:33 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:33 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
Oct 5 15:31:36 LPKENBITD002 modem-manager: (ttyUSB1): re-checking support...
Oct 5 15:31:36 LPKENBITD002 modem-manager: (Huawei): (ttyUSB1) deferring support check
View 9 Replies
View Related
Mar 26, 2011
I have a 3G modem Huawei e173s-6, the usb id is 12d1:1c0b. It's only detected as storage, not as modem. According to some tutorials I've found, I had to use usb_modeswitch and udev rules to make it automatically switch to modem mode, and usb id 12d1:1c05. I followed the tutorials, and the usb changes the id, but after the switch it is still recognized only as storage.
I have the suspicion that I have to add the driver to the kernel, since this is 11.3, but I haven't the slightest clue what to do. Does someone have experience making this modem work in 11.3? tutorial: USB_ModeSwitch ~ View topic - Huawei E173s working config
View 4 Replies
View Related
Jun 19, 2011
I am new to Linux and opensuse is lovely to me . However i have a problem, I dual boot windows and OpenSuse 10.3(because it plays mp3 out of the box) I actually tried newer versions but the problem is that I cant install this Huawei E1752 usb modem. I have failed people. Please help me. I need to use it for internet.
View 1 Replies
View Related
Jun 4, 2010
I tried to connect to the huawei cdma EC325 modem. using the network manager applet. System asked which tpe of connection i selected cdma and gave the username and password for the account and the password for my opensuse account.Still i cannot connect to the internet using huawei ec325 modem.How to rectify the problem What shall i do next.
View 2 Replies
View Related
Aug 31, 2010
I upgraded from 11.2 to 11.3 and with great disappointment I discovered that my HSPA modem, that worked out of the box under 11.2, work no more. At the first attempt NetworkManager is able to build the connection, I am able to use Yast to download new packages and online updating but at the first use of firefox the internet connection hangs up. Any attempt to disconnecting/reconnceting the usb stick gives the following error in the kernel echo:
[Code]....
View 2 Replies
View Related
Feb 5, 2010
I was absolutely dazzled, but my wife made me drop it after 20 days of not being able to get an internet connection.
I thought of trying again after so long to see if things had become easier for every Argentina user who has a Huawei connection (more than half of the country).
Unfortunately not.
The problem is the following:
I have a Huawei SmartAX MT810 usb-modem/router. In order to establish a connection, I need to run the following commands AS ROOT (which is why I cannot use a simple kde autostart bash script)
Code:
modprobe br2684 ; br2684ctl -c 0 -b -a 0.33 ; ifconfig nas0 up ; pppd call adsl
What's more, these commands cannot be run before the modem is operational, since they will end with an error.
In other distros I used to place these commands in /etc/rc.local. I tried placing them in /etc/rc.d/boot.local , but with no success: they are executed before the modem is operational.
In my complete ignorance of all things computer-related I thought it would be a good idea to place a caveat before the execution of the commands:
Code:
READYorNOT=$(dmesg | grep "modem operational") ; while [ "$READYorNOT" = "" ] ; do echo "Modem not operational" ; done
As a result the whole boot sequence gets stuck until I hit ctrl-c.
View 8 Replies
View Related
Aug 5, 2010
I can not get NetworkManager to handle my Huawei E220 usb modem. I have searched forums and tried a lot of things. I have just upgraded from openSUSE 11.2 to openSUSE 11.3 using zypper. It seems to work fine except that umtsmon stopped to work, so for now my laptop has no connetion to internet at all. Here are some information about my settings:
I have used usb_modeswitch to make the device a modem. Am I right if I say that usb_modeswitch is a one time command, or does it swap the setting each time it is called? Anyhow lsusb states that the device is a modem. (All the time.) code...
View 7 Replies
View Related
Oct 16, 2010
i tried to connect whit this key on opensuse 11.3 but i can't the device is recognized i start to connect it and the system show me "activating" but the light never comes blue , it's always green and it's impossible go to internet i use kde..
View 1 Replies
View Related
Feb 20, 2011
I am trying to use the HUAWEI E1756C USB stick to connect to the internet. Installing usb_modeswitch and usb_modeswitch-data allowed networkmanager to "recognize" the stick and set up a mobile broadband connection.
The result is that NM succeeded in connecting (one of every five attempts) but firefox does not surf, nor emails can be downloaded etc. Just like if not being connected. The USB modem shows the steady blue LED as connected.
A NM issue? I have tried disabling NM control and tried with PPP clients like NMTSMON, wvdial and even Sakis3g. All with the same results. They seem to connect and show flux up and downloaded but no surfing.
resolf.conf shows is pretty much empty and no DNS there.
The working settings in Window$ are:
Same settings with Sakis3G, or NMTSMON or NM result in connection with no action from applications that use the internet.
I have had a similar issue with WLAN each time I change to a different network. I solve that by forcing to update the DHCP. I mean using -su dhcpd wlan0
But attempts like dhcpcd ttyUSB0 or dhcpcd ttyS0 get the same result. So no idea if this is an DHCP, or DNS or another issue.
My box is an ASUS EEEPC 2005H netbook with OpenSuSE 11.2 and KDE
View 2 Replies
View Related
Jul 9, 2010
I have a weird problem on my laptop. Everything works okey on PC though.
I'm using kNetworkManager on my OpenSuse 11.2 on PC.
Everything works fine there with the following settings:
1. Make a new GSM Connection in kNetworkManager and enter settings there
2. Edit etc/sysconfig/network/config file and set .....DNS_Policy from "auto" to ""
3. Enter openDNS to /etc/resolv.conf (nameserver xxx.xxx.xxx.xxx)
It works like that on my PC.
I did the same on my laptop. The modem connects fine, but the DNS'es ain't resolved. So skype etc will work, but no pages will open in Firefox for example.
What else should I need to do to make this work?
It's weird it works the SAME way on my PC, but doesn't on my laptop.
View 3 Replies
View Related
Aug 11, 2010
I have opensuse 11.1 Gnome on Lenovo S10e. I'm wanting to establish a mobile internet connection. I have tried so far...*UMTSMON but when I click on it nothing happens. I have reinstalled the program several times to no avail. *WINE to run the Optus program, however the program doesn't find the HUAWEI USB stick & *Via a Bluetooth connection (use mobile phone as a modem) didn't work either Anyhow, I have tried these and some other ways to get mobile to no avail.
Also, have gone to network connections-mobile broadband-add-configure it- but what am I forgetting to do? Need a path I can take to get mobile internet working. (I even have a direct SIM card slot in this laptop
View 5 Replies
View Related
Aug 27, 2010
On google there is no information. Opensuse does not know anything about this chip. On that stick is a driver for Win 7 64 and a linux driver for debian. I shall " dial up" with an analog modem to get into the internet. All at the console over ppp and comands like pon and poff. there is no networkmanager. The web `n walk stick and its label is Fusion II. Perhaps anybody has similar problems.
View 2 Replies
View Related
Aug 24, 2010
I need a hand. I'm wanting to use mobile Internet but the UMTSMON program just simply doesn't seem to load, I click on it but nothing happens. I have re-installed several times, still doesn't start up.
adam@linux-7ipy:~> sudo zypper install UMTSMON root's password: Retrieving repository 'devel:languageserl' metadata [done] Building repository 'devel:languageserl' cache [done] Retrieving repository 'devel:languagesython' metadata [done] Building repository 'devel:languagesython' cache [done] Retrieving repository 'home:thomas-schraitle' metadata [done] Building repository 'home:thomas-
[code].....
View 1 Replies
View Related
Nov 29, 2010
I tryied to modify the root password, but instead of using the "passwd" command, i tried to use "usermod -p", without knowing what outcome exactly i would get. But since then, i can't log as root, neither with my old neither with my new password. And i can't install absolutely nothing on my machine.
Please, help me... i have a test next wednesday, and i can't work in my blueprint. In appendix, i've uploaded a print screen of the sequence commands, for you to be able to explain me this phenomenom and to tell me how to solve it.
View 3 Replies
View Related
