OpenSUSE :: KDE 4.5 Freezes From Time To Time With A INTEL GM45?
Oct 26, 2010
I don't know why but since I upgraded the KDE 4.4 desktop from openSUSE 11.3 to 4.5, the desktop just freezes some times.
If i was listening music, or watching a video I can still hear everything and even move the mouse, but nothing works.
So I switch to TTy1, perform a init 3, then init 5 to restart all the graphic system, and start again. This happens without message, without log, and without clue...
Should I downgrade to 4.4 or this has a Workaround?
Ever since I installed Ubuntu Natty, from time to time, for no particular reason, the entire computer screen freezes, and I am forced to hold the power button on my laptop to restart things with a hard reset. I cannot explain why it happens.
Such an issue never occurred in any of the past installations and versions of Ubuntu. This is a fresh installation of Natty by the way.
Also, I can currently be running a lot or nothing and it does this. Thus, it does not matter what I am actually doing (ie, what programs I might be running).
It has occurred about 10 times since I freshly installed Natty 6 days ago.
Just installed my first linux ever. The highest resolution I can get on my video card is 1024x768. I found out that I need to install iegd driver for my intell GM45 card. Can you tell me where I can download that driver and how I can install this?
11.3 installation appears to be completely unusable for mission critical workit's running/freezing on a Toshiba a300 laptop, intel 965gm gfx, using the drivers that where installed by 11.3whenever the unstoppable screen/monitor saver kicks in, it freezes the machine irrecoverably.same as: 11.3 kde constant lock upsthe unstoppable screen/monitor saver has been a pain in the neck in 11.2 too, is it possible to COMPLETELY REMOVE any code that will make the gfx go on standby? what a pain when you are watching a movie! disabling everything obvious never worked! wtf?
LIVECD of 11.3 Gnome works fine in my old PC. I installed several times and each time system freezes/crashes during boot. I am linux newbie, so, I am trying to figure out my problems. In Livecd I noticed Hardware info list's my SATA disk as IDE. Driver Modules: "ata_piix"Attached to: #24 (IDE interface). Is it right? I have posted Hardware information output in 01: None 00.0: 10105 BIOS [Created at bios.186] - Suse 11.3 install problem My machine specs are: Intel DG31PR motherboard, Intel core2duo, 3 GB DDR2 Ram, 250 GB SATA harddisk
I'm looking for a program that will digitally display the time in three different cities - all showing at once. I don't care if it is a panel applet or stand-alone. I'm using Suse 11.3 and Gnome.
Ok first off, I love debian, but on my new notebook I am getting a little frustrated with the terrible, video performance.Direct rendering is enabled on both systems, and openGL is working (I can if I wanted to use compiz etc...) fine on both systems, just running slow on debian.
I have tried Lenny, Squeeze and Sid, I have compiled the intel driver (and Mesa3D) from git and got it working (I am sure its working because its given me a slight boost), I ahve also tried building the latest stable (and RC2) kernel.If I install ubuntu 9.10 I get pretty decent 3D performance, its not ground breaking, but hey its an intel chipset so I am not expecting to kick the latest nvidia / ati card's backside.I really dont want to use ubuntu, I find it unstable when compaired to debian, but I also want to be able to play the odd game when I am bored, and at the moment I just cant do that under debian
New to Ubuntu. I've read all I can about the current mic issues with the Lucid 10.04 release. There does not seem to be any specific threads dealing with the GM45 chipset. I've had sound out of speakers on fresh install, and have done every single line addition (individually) suggested with:
Perhaps someone has run across this problem I loaded CentOS 5.3 on an AOpen MP45-BDR workstation. It uses the Mobile Intel 4 Series Express Chipset for the video graphics. It is officially identified as: GM45 chipset (Intel GMA X4500 MHD).
There are two problems. Using the "intel" video driver, the X11 server does not appear to support digital video cable (DVI interface). It is also stuck in 1024x768 resolution and I want it to display in 1280x1024 resolution. Using a DVI cable, the system boots and displays properly (GRUB and boot messages) until the X11 server starts, then the signal is lost. The system is configured with a dual boot (Windows XP Pro) and Windows operates properly and supports all of the features of the video graphics chipset (DVI and full resolution). So the hardware is ok.
The "intel" video driver has a description of "Experimental ..." so maybe there is an update to this driver or a replacement driver that supports this chipset. I checked the buglist and found CentOS bug ID 2951 which is somewhat similar. The user was utilizing the "intel" video driver and it locked his system but changing the driver to i810 was a work-around. My system does not lock. I did try the i810 video driver but the X server did not like it - it would not start. This makes sense since the description of this driver specifies support for the older Intel onboard chipsets.
Can someone tell my why every time I try to use 7z it freezes my system? I can't move my mouse, I can't type, I can't kill my xsession. I then restart my system and everything returns to normal. When I try to use 7z my system again freezes.
I have the problem using ubuntu 9.10 and 10.04 they both freezes after some time say like 2 or 3 min after login ..even the live cd freezes too but sometimes it works (its strange ) and when i select the advance option form live cd = acpioff, it works fine form the live cd. however my 9.04 ubuntu ultimate edition works fine. but i want to run 9.10 or 10.04. how to turn off the acpi form command like in regular installation i have xp installed side by side.
I'm dual-booting Vista and Ubuntu. Ubuntu freezes all the time, like every 5 mins so I don't ever use it. I just do a new installation every now and then to see if it fixes itself but it doesn't. It says that the battery has a low capacity, could this be the cause?it only freezes in Vista when I take out the charger, about at the same frequency as in Ubuntu.
I have two boxes that were originally used as workstations at a school - they upgraded and sold these.The two boxes are identical parts - Lenovo NetVista M42. I installed 5.3, installed RPMforge per the wiki instructions, did a yum -y update && shutdown -h now.The next day I turned the machine on and installed the UT2004 dedicated server. After a few hours I tried logging in via SSH - I could enter my user and password, but could not get farther. I rebooted the server. After another day the same thing happened. I moved the disk from the first box to the second and moved /etc/sysconfig/network-scripts/ifcfg-eth0.bak to ifcfg-eth0 but retaining the correct MAC address.
During this transition where the server "locks up" some things work and others do not. For example, if I type ping 4.2.2.2, wait 10 minutes and CTRL+C it looks like this (note the time of 0ms).
The system freezes all the time and I have no idea why, and the temp of core goes up to 56. Also, on the boot, right after grub menu selection, it restarts itself sometimes, again I have no idea why. I have lenovo y530. Which logs do you need?
I installed ubuntu 10.0.4 TLS version and my desktop freezes after a period of inactive time: the screen doesn't change and the apps do not response. It will resume after any key-stroke or mouse action. Is it a feature of 'power-saving' or something else? I need my ubuntu keep 'alive' all the time.
After some idle time Slackware hangs up/freezes. When, for an example, i turn on music i can hear it on idle time but after some time music still plays but i'm losing picture (monitor detects no signal), num lock is locked, led on keyboard are turned on but won't turn off while pressing num lock. I've switched off power saving options in Slackware and on bios setup.
My spec is:
X4 620 (without overclocking) AMD 760G (Radeon HD 3000) Catalyst 11.5 for Radeon graphic.
BTW - computer works fine with Windows. Also, with Slackware i can work for an hours, many hours and everything is fine but as soon as i leave it for some amount of time = it hangs/freezes. There is something wrong with hibernation. Not always computern is turned off correctly. TV is switched off, slackware logged off but i hear drives working and cooler fans. It should be switched off completly.
I just upgraded from F11 to F12. Everything seems to be nice except mouse. The mouse buttons (both left and right, except middle one) are accidently frozen for some times. It could happen when opening a new tab in Firefox, launching a program, opening a new windows. I cannot click anywhere but can use mouse wheel. I have to log off/ log in and it becomes normal. It does not happen so frequently (around 3-4 hours) but it is really annoying.
I installed network-manager-vpnc, configured cisco vpn through NetworkManager. It works slow, but the bigger problem is that after minute or so the connection just freezes.Then I tried kvpnc. It works like it should from speed point of view. But it also hangs up after minute or two.Tried to change MTU of my wired connection to 1500 - no good.Tried to uncomment line in /etc/ppp/options "mru 542" - no good.
Created /var/run/vpnc because it was giving some error "can't open pidfile /var/run/vpnc/pid for writing".From logs everything seems fine except for "nm-dispatcher.action:Script '/etc/NetworkManager/dispatcher.d/01ifupdown' exited with error status 1." in last line. If I use kvpnc it gives no errors.SO, how do I debug this thing or does anyone knows something I don't in this case?
I've been using Thunderbird 3.0.x for some time and found in it a good replacement of TheBat. However, few days ago, ubuntu being ubuntu crashed and since then, Thunderbird freezes after 10 seconds every time I try to start it, sending CPU usage through the roof. I have 8 imap accounts in it and my profile folder is ~2.8gb I tried purging the installation. I tried fsck on all partitions. Windows Thunderbird using the same profile folder works just fine.
Attempting to install 10.04... I can get to the "Where are you?" screen, then the little circular "please wait" cursor spins forever and ever.
Here are a few things I've tried, with no success:Leaving it alone for hours, hoping it was just taking a really long time. No Dice. Unplugging any hardware that might be causing a problem, including the network card. No dice. Burning it to CD, DVD, and booting from a USB key. No dice. Trying every combination of kernel options I could find in the forums, and setting most combinations found in the "more options" menu in the boot screen. No dice. Booting into the live environment, then installing from there (instead of just choosing "install" directly). No Dice. Booting both from the 32-bit and 64-bit ISOs (my machine is 64-bit)
Note: I have not tried just upgrading from my 9.10 install, and I will not try this. If I can't get a live CD to boot, there's no way I would voluntarily hose my current system by upgrading.
Also note: I checked the MD5 of the ISO, and did the "check the disk for defects" menu option as well. Everything checks out fine.
I installed Fedora 15 last week, on my main PC, and I absolutely love it. Defintely my favourite operating system. Now I have a few questions. I thought I would put them all in one thread, instead of making seperate ones. I did search before I posted, and I cant seem to find any solution to my problems. So here it goes.
First question, I am using evolution for my e-mail program/client. My email addresses are all hosted by hotmail. Now I have set them all up correctly, but cant seem to send e-mails(I recieve them perfectly fine). I am using the "smtp.live.com" server, and using SSL encryption. I have tried messing with the settings but have had no luck. Has anyone figured out how to fix this?
Second question, I play minecraft frequently, and I am currently starting the program via terminal [java -jar /home/username/minecraft.jar], which works flawlessly. However it is too slow(open terminal, type it in. I need a simple click), is there any other way to start minecraft?
Third and last question, What is the best way to close minecraft? I notice if I just close it(via right click, and close, or clicking the X) it freezes and stays open for a long time. Is there any better way to close it?
I am trying to install ubuntu netbook edition on my Acer aspire one D150. I have tried to do this before with version 9 with no luck so I waited until 10 to see if the problem goes away; apparently it has not. I put the ubuntu install files onto a USB stick according to the instructions from ubuntu here for windows (I have windows xp on the netbook now).
When I shut the PC down and turn it back on with the USB key inserted, the laptop just seems to hang at the ACER splashscreen. This screen is where I could press F2 for setup or F12 for boot order; the buttons do not respond, the USB key appears inactive. Again, it just seems to hang. I've waited for as long as letting it run all night to see if it goes anywhere by the morning with no luck.
I'm trying to fix a friends EeePC notebook (Asus) running a recently upgraded Ubuntu 10.04 from Karmic Koala. She used the update manager for the upgrade to 10.04 LTS and everything was fine until she had tried to install something from the Ubuntu Software Center (she doesn't remember what happened). After that, both Update manager and Synaptic stopped working.Update manager gives the following error:Quote:Software index is broken. ... Try to use synaptic for something?!...
Then Synaptic manager gives the following error:Quote:E: dpkg was interrupted, you must manually run 'sudo dpkg --configure -a' to correct the problem. E: _cache->open() failed, please report.And when I try that command, the terminal just keeps blinking with the cursor and does nothing for more than an hour. This is the output of the comand:Quote:
jasna@Jasna:~$ sudo dpkg --configure -a [sudo] password for jasna: Setting up moodle (1.9.4.dfsg-0ubuntu4) ...
When booting Fedora 11, my system hangs for a very long time on starting udev. Sometimes I get an I/O error. However, my hardware is fine. I do eventually get in to the system.
It takes me a while to log in the splash screen just sits there for ages before i get to the desktop. Never used to be this slow and I'm not sure why. Firstly, I'm running Ubuntu 11.04, standard DE. I do have conky starting up in a script but it has the & at the end of the line so I didn't think this would cause it (or is there some special case for log in time on how & is treated?). However as a test I will comment out the line in the script and see if it is the cause.
However just for general knowledge and in case that isn't the problem, how does one go seeing what is happening during the time from when one log's in and the desktop is displayed? Is there some kind of log that shows the date/time that can be enabled or is there a debug mode that can be enabled somehow via special keys or maybe from grub?
I am using Debian linux. I have 100 timers running. If a timer expired which will generate a signal and it was mapped to a same function handler. All the timers are mapped to one function handler. The problem is if the timer expires one at a time, the function handler called at a time. But if the 2 timers expires at a time, the function handler is called one time only instead 2 times. Is it possible to invoke the function handler as many times based on timer expirary happens simultaneoulsy?
I've got fedora 11 set up to use network time protocol to sync my laptop's date & time when I'm on-line. The question is simple really, I've added a local universality's time server (what is public) and it's live. but it's added to the end of the default time servers what come with fedora. How do I get fedora to just use the local time server, is it a case of removing the default time servers for fedora, but there is a box what says advanced options which are. sync system clock before starting service ???? & use Local time source (( is that the same as the local ntp server that I've got set up ))Hope some body can help me with the network time protocol part of Date/Time settings.
