OpenSUSE Install :: How To Adjust The Screen Resolution
Jul 17, 2010
Suffering from the expected error in detecting my video properly when installed 11.3.Have intel 915G onboard video. Up until 11.1 Opensuse struggled with loading this correctly. in 11.1 & 11.2 all was well. A couple of minor tweaks in sax2 and it worked perfectly. Now hat sax2 has gone I'm not sure how to make these minor tweaks.
My problem is I have been forced to a screen resolution of 1024X768 VGA Following the readme file adding nomodeset at boot fixes the problem but of course forces me back to an old video driver with pretty poor performance. Is there any way I can change the screen resolution and set the correct monitor - any GUI replacement for sax2? Krandrtray will only let me set a max res of 1024x768. I need to set res to 1280x1024
View 2 Replies
ADVERTISEMENT
Oct 28, 2010
On last boot it was fine but now it is showing 800X600 which is too low . How to adjust it
View 9 Replies
View Related
May 30, 2010
Have just installed my frist linux os and the screen has a big black border around it. Set the res on install to 1024x768 & this is displayed in display settings. If I run xrandr in a shell tool it only shows 640x480 available.xorg.conf has "1024x768" "800x600" & "640x480" available.Have search the web but nothing I've found works.
View 14 Replies
View Related
Aug 7, 2010
I just want to know how to adjust the screen resolution of my boot up screen. My PCs maximum resolution is 1366x768 but I think my boot up screen only uses 600x400. I doesn't look nice for me. The logo of Kubuntu is too big and the colors are not the true colors of the Kubuntu Boot up screen.
View 2 Replies
View Related
Jan 5, 2010
I've been trying for very long now to adjust my screen resolution to my desired setting. So far, no luck. Just today I went in to examine what my xorg.conf looked like and this is what I saw.
Section "Screen"
Identifier "Default Screen"
DefaultDepth 24
Option "AddARGBGLXVisuals" "True"
[Code].....
View 3 Replies
View Related
Jul 19, 2010
I have an HTPC mini computer, in which I've just installed Ubuntu 10.4 Lucid Lynx, and I tried all screen resolutions I could possibly use through the settings. And the top, bottom, left & right hand sides are out of the resolution. So for example the top and bottom taskbars are out of the screen. I'll be posting a photo later on today to show you people exactly what I mean. So that I can have Ubuntu's screen would fit all inside my LCD screen ? The HTPC runs an nVidia graphics card.
View 3 Replies
View Related
Mar 9, 2011
Can I adjust the screen resolution like windows system? Fedora 14.
View 6 Replies
View Related
Apr 26, 2011
The last update for 10.04 has really screwed my desktop. Several of the icons are off the bottom of the screen. All icons are too large. Can't adjust the screen resolution. Panel at the bottom when placed in autohide is so sensitive that it is almost impossible to use. Jumps up and down like a flea on a hot stove. I have reduced the sensitivity of the mouse to the minimum with no effect. There is no excuse for so many troublesome updates. The problem with using an external monitor with a laptop has never been resolved by Ubuntu.
View 3 Replies
View Related
Oct 18, 2010
I booted Hardy, because Karmic detects no screen, after trying to adjust to a previously recognized resolution. As good as it is, does it seem like some basic computer functions just do NOT improve?
View 2 Replies
View Related
Aug 27, 2011
I recently upgraded my graphics card from a Geforce 7600GS to a Gefore 560Ti. And while most things are normal, during boot up my screen isn't "full screen" until X is started, after which everything else is fine. Essentially, all display, the grub menu, the splash screen, console text, etc, is within a box on the screen, with 2" on the left and right, and 1" top and bottom of empty blackness.
From what I understand, this is because the framebuffer is using the wrong resolution, but the maximum resolution that hwinfo --framebuffer returns is 1280x1024 (which I am already using "0x031a".) (My monitors is natively 1920x1080) Is it possible to do something about this? If not increase resolution than at least stretch the screen to full screen?
sudo /usr/sbin/hwinfo --framebuffer
02: None 00.0: 11001 VESA Framebuffer
[Created at bios.459]
Unique ID: rdCR.GGyCBArXznD
Hardware Class: framebuffer
Model: "NVIDIA GF104B Board - 10400050"
[Code]...
View 2 Replies
View Related
Jan 12, 2010
I am installing 11.2 on an older machine, Athlon 2800+, GeForce 6800, 1 GB RAM. Install goes fine until try to reboot to the OS and just get massive garbage on the screen. Can't see anything just lines crossing the screen, it seems almost like the resolution is way off but don't know how to change that since I can't see anything. I tried two different install disks to make sure not the problem and got the same thing with both. I tried installing both KDE and GNOME on separate occasions and still same problem. I have used the same install disk to put this on an even older machine and that went fine. I do have windows 7 installed on another partition. I'm fairly new to linux but I'm learning.
View 9 Replies
View Related
Jan 20, 2011
Opensuse 11.3 with latest updates
KDE desktop
Whatever resolution I choose, 1600x1200 is preferred, it is reset to a default of 1024x768 when I log out. I use the "Configure Desktop" option to set the resolution. I can find no other method to do so. The graphics adapter is an ATI hd3200. I have installed the fglrx driver. I cannot fine the "Control Center" for the driver. How do I make the selected resolution permanent?
View 4 Replies
View Related
Feb 24, 2011
installation opensuse 11.3 and kde 4.4 after update to kde 4.6, work fine, but problem is login screen is low like 640x350...? i wanted to change from lowtion to high 1024x768?when i start opensuse and begin to login was low resolution and log in my user and it's low resolutiona dn i change screen from setting system (kde) after change high display is works fine and rebbot same low resolution for LOGIN MANAGER how i can change it??
View 1 Replies
View Related
Nov 10, 2010
I am trying to change the default screen resolution in Run Level 3 to 640x480. I have tried changing the menu.1st file and the vga=0x301 mode sticks until the system begins to boot and then resets to a higher resolution. This system does not have X, or Sax2 so no go on those options. This is OpenSuse 11.3 x64.
View 6 Replies
View Related
Mar 23, 2011
Is it possible to scale my screen to a bigger size? I have a huge TV as a monitor and at 1920x1080 on linux it is a bit of a strain for my eyes. on windows they have a feature to do this. You can make the text and other items, such as icons, on your screen easier to see by making them larger. You can do this without changing the screen resolution of your monitor or laptop screen. This allows you to increase or decrease the size of text and other items on your screen while keeping your monitor or laptop set to its optimal resolution
View 8 Replies
View Related
Jul 4, 2010
I got my hands recently on openSUSE 10.2 (ppc) to put on my b&w powermac g3. i can boot from the cd and it gives me a text prompt and the choices install, rescue, and something to do with the network (which is whatever), and a not-very-helpful help option. so i type install, and my monitor says "input not supported." i figure, "ok, that's cool, i'll just plug in one of my old crt monitors 'cause it must be trying to use a resolution lower than my fancy-schmancy one supports." plug in the old one, restart, type "install," same thing. i'm not new to linux, but i don't really have any options with this prompt that any manner of googling or thread-hunting can uncover which allows me to specify the resolution at which the yast installer starts (or refresh rate, maybe that's it...) or lets me keep it in text mode through the installation. I tried typing "install textmode=1" which seems to do nothing special (same result as just "install") and just "textmode=1" (which is a fundamentally retarded approach, but what else am i supposed to do?). Once the operating system is installed and i can boot into a terminal, i figure can edit the xorg.config to use the resolution i want, but i can't very well install the system without seeing what i'm doing! It's just confusing 'cause it doesn't seem to like any display i give it.
View 3 Replies
View Related
Jan 31, 2010
Some month ago I installed openSUSE 11.1. It worked not bad, but I wanted to get the newes release of Firefox. So I did an upgrade to 11.2. Yast2 refused to work with an error message: unknown option -s (or similar). The regular updates didn't work also. Then I decided to do a new installation. Now I'm having a new problem: Display settings (Anzeige-Einstellungen) reports: Monitor unknown (Monitor unbekannt).
Possible resolution settings are: 800 x 600; 640 x 480; 400 x 300; 320 x 240;
Possible refresh rates are: 60 Hz or 56 Hz @ 800 x 600
I need 1024 x 768 @ 76 Hz. In the previous installation it worked well. How I can teach openSUSE to run 1024 x 768 @ 76 Hz?
YAST2 Hardware information shows me in Monitor > Monitor > Resources > Resolution: High: 768; Vertical frequency: 76; Wide: 1024
The VGA controller is also correct shown in Display > 3d Blaster Savage 4
View 4 Replies
View Related
Mar 25, 2011
i changed the boot up resolution in the boot up loader to 1366*768 (native res of my monitor) the boot option is still set to quiet splash however, instead of showing the progress bar, it would now always display the complete boot up log ( the list of starting services and such) i then manually changed the boot option from to 1024*768 at boot loader screen, and teh splash would show up, but then on next boot up if i stick with 1366*768, it doesnt work again
View 4 Replies
View Related
Jun 11, 2010
I have just did a fresh install of Ubuntu 10.04 to a computer with a generic, low end, on board graphics card. It will not allow me to change the resolution to something other than 800x600 or lower. 8.04 allowed me to set the resolution to as high as 1600x1200 using the same monitor/graphics card.
View 4 Replies
View Related
Jun 10, 2011
I am installing CentOS 5.6 on an old PC with a small LCD monitor. Anaconda did not determine that the resolution of the monitor is limited and it configured the display to 1280 x 1024 which is out of range for the monitor. So I connected a different monitor and completed the install then set the resolution to 1024 x 768 which the monitor should accept. I connected the small monitor but it still displays "OUT OF RANGE" when the PC boots.
I then connected to the PC over ssh and changed /etc/inittab to start in runlevel 3 and rebooted the PC. At the moment I am downloading the necessary updates with yum and pondering the problem. Some Internet searching tells me that I can adjust the resolution with Xconfigurator. That beings back old memories of Red Hat 7.x.
However, Xconfigurator is not present on the CentOS 5.6 install. So... short of shutting down the PC I am on now and transferring the monitor back to the old PC and trying another resolution etc. Is there a way to change the resolution without running the gnome gui and using the System; Preferences;Display Resolution tool? I am not running any proprietary video drivers on the PC.
View 2 Replies
View Related
Jan 6, 2010
why both ubuntu and centos 5.4 will only give me 800x600 resolution on my monitor when opensolaris immediately gives me 1280x1024?The first time I tried ubuntu it gave me 1280x1024 and now will only make 800x600...This is a viewsonic VG930M Monitor..
View 4 Replies
View Related
Mar 23, 2011
I have a problem with my graphics (exactly this one: [URL] I've got an Intel 845G chipset and a LG Flatron F900P monitor.A friend of mine convinced me to try ubuntu and I installed the 10.10 version. Everything (except the monitor's resolution) works all right.
My computer is: IBM Net Vista 8305-21G
Chipset: FRU PN 49P1599 (Intel 845G)
View 9 Replies
View Related
Apr 12, 2011
How to adjust resolution in Mandriva 2009.1?
View 2 Replies
View Related
Jan 11, 2011
i have just put a Geforce 7300 GT graphic card into my machine the problem is the max resolution I can get is 1024x768 at 60 hz the screen is a benq fp71g+. also the screen goes blank when i click on the display icon in system settings. i know that the screen can be run at 1280x1024 so I don?t know where the problem is.
View 3 Replies
View Related
Feb 28, 2011
I'm trying to install Ubuntu Desktop 10.10 on an Intel Atom mainboard (Intel D945GCLF2) with CRT that has been running Ubuntu 9.x previously.
Both, Desktop live CD / installer and alternate install CD cause the screen to go black (and the status LED blinks).
I was able to get a bit further into the boot process with nomodeset as parameter with the Live CD, unfortunately I can't pass GRUB any parameters now that I have used the alternate Install CD by pressing 'e', it just boots.
So now I have Ubuntu installed, I get a terminal with CTRL-ALT-F1 but I don't know what I need to do now or how to adjust resolution or video settings from command line.
View 1 Replies
View Related
Jan 13, 2011
where the time to display media notifications is stored? When I put a CD or DVD into the player slot, a popup window shows possible actions to take but these old eyes can't read it fast enough to get through the list. Is it possible to get it to display longer and if so how?
When I put an audio CD in the slot, the display says there are six (6) actions possible but I only have time enough to read the first 2 or 3.
View 2 Replies
View Related
Mar 13, 2011
Computer boots up fine, but drops to commandline as it tries to go to the desktop. Just logging in and issuing "startx" brings up the desktop and all is well.
The Xorg logfile gives no fatals or clues (at least to me), but the "warn" file in /var/log gives the following at the end:
Mar 13 13:25:43 xxxxxxxx kdm[2328]: X server startup timeout, terminating
Mar 13 13:25:43 xxxxxxxx kdm[2328]: X server for display :0 can't be started, session disabled
Yesterday was fine, and never had it before; no harware changes (still same ATI 4770 and ATI 11.2 driver), nor BIOS changes/updates, for ages. First boot today this started. Does it continuously.
how I might slightly increase X's timeout parameter a bit, if this is the problem?
View 9 Replies
View Related
Aug 7, 2010
I have windows installed through virtual Box now but i have some questions. When i make it full screen it goes full screen but Windows stays in the middle of the screen small and doesn't adjust to the full screen. Can you make windows completely take up the full screen Can i access folders on my ubuntu drive ? i have a file in downloads i want in windows but don't want to reinstall it
View 4 Replies
View Related
Dec 1, 2009
I want to use secure file permissions within OpenSUSE, but having to provide the root password for every window I click is just a little too much.Wonder what the setting "paranoid" does then. And I also wonder how to adjust the safe settings to not get prompted with every single click.
View 9 Replies
View Related
Feb 16, 2010
I am having a problem with my touch-pad on my Dell Inspiron 1525. It needs to be adjusted for speed and it starts scrolling unexpectedly. I understand I need to install a driver for it but don't know how. The problem I see with Linux is that it's not easy to install software for new users. I have ran into a few One click Installs and managed to work them out quite easily. Usually the documentation you find online to install programs assumes the end user knows how to install.I need to know how to install the touch-pad driver from start to finish and all steps in between.
View 2 Replies
View Related
