The crash happened when I was reading a web page and the screen went black and the mouse pinterr dropped to the middle of the bottom of the screen and froze. I had to do a warm reboot to get going again. I'm using 11.4 with KDE.This is the section of the /var/log/messages from around the time of the crash at 16.42/16.44.
View 9 Replies
I'm running Scientific Linux 5.5 (equivalent to CentOS 5.5), and over the past two weeks, I have had a problem with my root partition filling up, preventing anyone from logging into the server.After searching for large files, and finding none, I was mystified when du told me that the root partition had only 660 MB of disk space used, whilst df showed it full. The problem was this: the /var/crash directory had been filled up by an 8GB crash file. Now, I'm a 'proper' sysadmin and make sure that /var has its own mount point, so the crash should not have touched the root partition at all. Except it did - instead of writing to /var/crash on /dev/mapper/VolGroup00-LogVol04 which is mounted as /var, it wrote the file to /dev/md0 directly, so when all the file systems were mounted, those files were hidden under the mounted /var.
View 4 Replies View RelatedAfter a fresh install of Suse 11.4 X-system comes up with the wrong screensize 1680X1200.
Instead I need 1600x1200. How can i set permanently the screensize I need ?
I switched today to slackware-current on one of my desktops to play with it and ran directly into a problem.
Since ages my lilo.conf has two entries for slackware. One for runlevel 3 and one for runlevel 4.
Code:
Since the upgrade this is no more possible because I get a kernel panic as soon as udevadm trigger is called. The stack says something about an unknown boot option. Because that i removed the append lines from my lilo.conf and i was able to boot the system. The crash happens when udev is called from within the ramdisk and afterwards. I tried both.
My question is now. Is this a bug in udev or expected? I have this setup since at least 5 years and had never problems with that. What do I have to do to be able to select the runlevel at boot time?
I am trying to install a Java based game to try it out and i keep getting a crash report can anyone assist me with getting this to work?
Code: Unexpected crash while launching login The error was: <null>
It's possible you might figure out what's wrong from the log file below.
Contents of temporary launch log:
Time is Mon Mar 28 06:40:58 EDT 2011
Running client version 2.7.5g
System information:
Executing from /home/jerry/Documents
Operating system: Linux (arch: amd64, version: 2.6.37.1-1.2-desktop)
Java version: 1.6.0_20 (Sun Microsystems Inc.) <http://java.sun.com/>
Jvm version: 19.0-b09 (Sun Microsystems Inc.) [OpenJDK 64-Bit Server VM]
Available CPUs: 2
Main thread exiting.
CLIENT CRASH
The /etc/profile said that i should do that in /etc/profile.local.I create /etc/profile.local, set the aliases, then i reboot.Now i've got a broken bash enviroment. Prompt has gone, ls colors gone, useful aliases (md=mkdir) gone.I've got this prompt: 'bash-4.0$' instead of the 'username@hostname:actual dir'.The root account has got the same errors, so i think i broke something system-wide.I removed the profile.local but the problem stays.What should i do to regain the standard bash enviroment?
View 4 Replies View RelatedWhat the right place to report errors in package descriptions ? There are more than two dozens categories mentioned on the openSUSE "reporting a bug" web page but none of them seem to fit. The packager of the concerned rpm is bugs.opensuse.org, no email printed out when launching rpm -qpi <package name>.
View 2 Replies View RelatedI'm just using a plop boot cd...it does what I need, boot from hdc 2. or (hd2,1) I'm having an issue, because Im not sure how to change the mbr so when I boot the computer from the third hdd, it just works...where is the MBR, and how do I edit it, or better, is there a GUI interface I can use?
View 9 Replies View RelatedI wrote a few minutes ago open Suse 11.04 instead 11.4, I got confused with Ubuntu's last version.
View 2 Replies View RelatedI've installed OpenSUSE 11.2 x64 on my Intel Core 2 Quad machine with 8GB of RAM nstallation went perfect. After the main installation, I've installed the XEN-kernel. Booting into the XEN-kernel goes fine.But, now I want to install the first domU (paravirtualized). I use the same installation disk but OpenSUSE 11.2 won't install. It crashes directly. Neither the x64 or the x86 version works.The strange thing is that I can install OpenSUSE 11.2 as "full virtualized".Also, OpenSUSE 11.1 (paravirtualized!) as a domU works perfect!!
View 9 Replies View RelatedI have tried install drivers of Ati ,9.10 and 9.11 always same result black screen, i think problem is information on installation system is on glibc 2.1 but, I have tested and glibc 2.3 and 2.2 are installed, for that the result is :
Unloading radeon module...
Unloading drm module...
[Message] Kernel Module : Trying to install a precompiled kernel module.
[code]....
I installed opensuse 11.2 on ASUS R2E nicely It have a 7" touchscreen and works nice. The screen is correctly settled to 800x480 on boot however after a S2RAM it is reinitialized as 800x600. I made an xorg.conf with only one fixed mode on 800x480 but daesn't seems to be considered on resume. After cold boot sax2 get the right size (800x480) and after resume 800x600 The video chipset is intel 945 GM.
May this be related to hardware reinitialization ? How to re-initialize X on resume ?
I just happened to lock myself out of ssh access on my xen virtual server since I changed the ssh port but forgot to open it in the firewall. No problem, I just access it through VNC in VM manager, I thought, however I have some special chars in my root password and the keymap through VNC seems to have changed somehow. So I cant login as root, nor do su or sudo. I can login as user. I need the sign " but can't figure out how.
View 1 Replies View RelatedJust completed a fresh netinstall of OpenSUSE. This machine previously had a Ubuntu install on it, but I was having all sorts of issues and decided I required a fresh start. The install itself went acceptably, although I ended up manually fixing GRUB.Now the system is running, I've got a ridiculous problem, in that I'm still seeing the old hostname- It used to be ubuntu-server, but should now be unimatrix-001.Checked both the obvious places (/etc/HOSTNAME & YaST), but the correct hostname is in both of them.
View 5 Replies View Relatedmy OpenSuse 11.3 worked absolutely perfect - till now ! It suddenly started not to load KDE, but instead prompts the login screen. When i then log in, it just crashes after a minute or so. I tried to boot in IceWm and it appeared more stable to me, but when i opened a programm like firefox or gimp, this Environment crashed too.
View 4 Replies View RelatedI am having plasma crashes for the past few days. I'm running KDE 4.5.2 and it was all running fine. Then the latest runs of updates happened and now I can't get a desktop. KDE runs but plasma fails to start leaving me with a black screen and a mouse pointer. This happens in both failsafe and normal, with or without a fresh .kde4 folder and consistently! Here's what the KDE bug window tells me.
[Code]....
Just installed OpenSUSE 11.3 64-bit. I have a program that uses libjpeg, so I installed libjpeg and the dev modules. It has both version 6 and 8 installed. When I run my prog and try to access the lib I get this error: Wrong JPEG library version: library is 80, caller expects 62 This seems a common problem elsewhere. Anyone know how to fix it in 11.3 ?
View 1 Replies View RelatedTrying to clean up my system having removed some factory repos so now I have the standard 4, update, oss, non-oss & packman. When updating and switchine to packman I get many Wrong Digest errors and when downloading many NO KEY messages.
What is the significance of the no key message. How can I renew keys from repo sites and what should I do about the Wrong Digest warnings?
Is there some better way of getting my display size set to 1280x960 when I launch openSUSE 11.4 under VMware Server? Here's what I've done so far: I am running Windows 7 on an AMD Phenom II system (motherboard: Gigabyte 880GMA-UD2H). I installed VMware Server (version 2.0.2) so that I can run openSUSE 11.4. The initial install went pretty smoothly. However, the display size was set to 800x500. I attempted to set it to 1280x960 by changing the /etc/X11/xorg.conf.d/50-monitor.conf file as follows:
Code:
/etc/X11/xorg.conf.d/50-monitor.conf
Section "Monitor"
Identifier "Default Monitor"
## If your monitor doesn't support DDC you may override the
## defaults here
# HorizSync 28-85
# VertRefresh 50-100
HorizSync 1-10000
VertRefresh 1-10000
## Add your mode lines here, use e.g the cvt tool
Option "PreferredMode" "1280x960_60.00"
# 1280x960 59.94 Hz (CVT 1.23M3) hsync: 59.70 kHz; pclk: 101.25 MHz
Modeline "1280x960_60.00" 101.25 1280 1360 1488 1696 960 963 967 996 -hsync +vsync
This resulted in a display size of 1734x1342 (or something close to that). I noted from the /var/log/Xorg.0.log file that the vmwlegacy driver is being used instead of the vmware svga driver. There is a note that the vmwlegacy driver does not support the "PreferredMode" setting in the monitor section of the xorg.conf files. For the time being, I have set my horizontal and vertical rates to 60kHz and 60Hz, respectively. This does limit the maximum display size to 1280x960, but for all the wrong reasons. How do I set up my system to get the correct display size?
I think I've totally destroyed my Suse install, but I have no idea what happened.
I was running Yast's "Create a backup" utility and my screen totally went black and kicked me to the login screen. I was unable to log in, except to a terminal.
So, then I tried to restart X (by typing startx) and I get "Fatal server error: Server is already active for display 0"
I've tried running the repair utility, and it doesn't work. Through a number of commands, I was able to start up a second X session, but that wasn't really much help.
My system just crashed and I had to reboot. The only interesting message I have found in the logs before the crash was :
Code:
2010-11-22 07:49:22 linux-lx7s smartd[2259] Device: /dev/sda [SAT], SMART Prefailure Attribute: 1 Raw_Read_Error_Rate changed from 114 to 115
2010-11-22 07:49:22 linux-lx7s smartd[2259] Device: /dev/sda [SAT], SMART Usage Attribute: 190 Airflow_Temperature_Cel changed from 61 to 60
2010-11-22 07:49:22 linux-lx7s smartd[2259] Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 39 to 40
[Code]...
So I installed this system with the net install disk. I really don't want to do that again. It said it needed one update shortly after install and I figured that a net install would pretty much be up to date and I would be fine to wait on that for a day or two. Wrong. I used bit torrent for about 20 hours and downloaded ~60 GB's to the external hard drive. After a while while clicked the little update button closed every thing else then hit apply.
Walk off, come back and the computer is completely non-responsive and the monitor is not getting a feed from the tower. Not even any num-lock blinky light action on the key board. I gave it a minute or two to show any kind of life then turned it off. It came back on well enough to get online and post this but, like the title indicates, that package manager appears to be broken in some way. In Debian based systems there is a command that clears this up. Is there an equivalent for this distro?
I attempted to finish the update but got this error:
Code:
installation of package failed.
Subprocess failed. Error: RPM failed: error: package NetworkManager-glib-0.8-7.4.i586 is not installed.
Why not just disable that update and see what happens? That's what I said; heres what happens:
Code:
Installation of package failed.
Subprocess failed. Error: RPM failed: error: db3 error(-30987) from dbcursor->c_get: DB_PAGE_NOTFOUND: Requested page not found
error: error(-30987) getting "" records from Requireversion index
error: db3 error(-30987) from dbcursor->c_get: DB_PAGE_NOTFOUND: Requested page not found
error: error(-30987) getting "" records from Requireversion index .....
The above pertains to a fire fox update of some kind. I still have the install disk handy but would rather not wait the 3 hours it takes to download the packages. How I can fix this. I switched from Ubuntu to SUSE because it is supported by online learning soft ware I have access to.
Bug-buddy tells me vmware-user crash on every-time I boot up. I don't know what to do about this just pop-up without i changed anything on my machine. I saved a "crash report" on the desktop but couldn't understand what was the "problem" when I read it.
Opensuse 11.3 gnome.
After upgrade KDE to 4.7, I restarted system, when login, the klasma-desktop always crash. can't start.See, below picture:https://picasaweb.google.com/lh/phot...eat=directlinkAnd got below info:
Code:
Application: Plasma Desktop Shell (kdeinit4), signal: Segmentation fault
[KCrash Handler]
[code]....
I updated from 11.1 to 11.2. Before some intelligent person says, I should never update but do a new install: a new install isn't better, then I have other problems to tackle. And I really would like updates to work.Well, I have the following problems and I hope you don't mind me listing them all in one post *it's difficult for me to type on this keyboard layout):1. home isn't found or set up. I have modified fstab to mount /dev/sda6, which is home, but it won't mount it at startup, and also not when it's just using the disk/by-id line that had been put in.
2. the keyboard layout is american, while the system language is set to German (I'm German and would like also my keyboard to know that). I had no chance to change that, even a loadkeys de-latin1 doesn't help3. OpenOffice drives me crazy. It just doesn't start properly, or at all. It doesn't open a number of documents, but it doesn't also give any error message. Sometimes soffice.bin is in the list of processes, but OOo is nowhere seen. After killing the process (or terminating it), I can start it, but have only the opening screen and cannot really open a document.4. printing doesn't seem to work, either.Needless to say that everything worked fine before the update
I am an openSuSE user for many years. My current installation is openSuSE 11.2. However, my first was SuSE 6.4 and I have been _constantly_ upgrading since then until reaching the current openSuSE 11.2. The technical issue I have been facing lately is with the kernel version of my current system: although it should be 2.6.31.5-0.1-desktop, as this is the one I have chosen via the online update mechanism and the yast2 system boot-loader procedure, grub shows it as preselected, the boot procedure in the end greets me mentioning this very kernel version, _but_ when I issue the command: uname -a in a command prompt, I am informed of using linux kernel version: 2.6.18.2-34-default #1 SMP PREEMPT
I am really quite puzzled, since I _cannot_ find any such vmlinuz file under /boot/ ! Could it be that my system properly runs with the expected kernel version, but uname mistakes it with a different one? Is there a way to determine the actual version of the linux kernel that my system currently runs with? If it's a problem with uname, have you got any suggestions that could potentially shed some light towards the origin/cause of the reported issue?
I did apply the updates on 11.1 32bit and upgraded the kernel from 2.6.27.45 to 2.6.27.56.
Now:
Code:
> uname -a
Linux myhost 2.6.27.45-0.1-default #1 SMP 2010-12-01 16:57:58 +0100 i686 i686 i386 GNU/Linux
but:
Code:
> cat /proc/version
Linux version 2.6.27.56-0.1-pae (geeko@buildhost) (gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP 2010-12-01 16:57:58 +0100
Used to run Gentoo, years ago, getting back on the linux train. Anyways, got a new media pc and am having some troubles getting it to function. I am using ImageWriter, an OCZ Rally 4gb flash drive and have tried both HTTP and BitTorrent downloaded copies of 11.3 with the same md5sum check wrong error. What am I doing wrong? Is it because it thinks it is a CD or am I getting bad copies of the ISO? I am so out of practice I can't remember anything about installation anymore and am at a loss.
View 5 Replies View RelatedMy wifes computor crashed during an update with a message to fill in a report. It would not respond to any key presses. The computor has been running 11.3 since it was realeased without problems other than jerky video. The computor will not boot it asks for the password but does not accept it, Although I can see the Home folder it does not mount. I have tried testdisk but although it sees the partions it cannot acess them.
View 5 Replies View RelatedI've borrowed a copy of 11.4 DVD install disc from someone at work, everything went fine install wise. Except Grub taking control, which I didn't ask it to, but easy fix with yast, problem is firstly my graphics resolution is wrong, but I'm trying to work that one out myself as it always seems to be happening with distros I use on my machine. The weird thing is my desktop blinks! Every 10secs or so the whole screen goes blank and then reappears? I thought it might be the wrong refresh rate, but that's at 60Hz which is correct, would it be the resolution problem?
My hardware:-
P4 2.8
1Gb ram
Geforce FX 5500
Dell 1703FP monitor
I was trying to running diagnostic's from Opensuse, but the blinking was getting on my nerves and I'm not familiar with a non Debian based OS......yet! I've got compiz and all running on the hardware in my Ubuntu install after editing the xorg.conf, could I simply copy that to my Opensuse install?
