OpenSUSE Install :: ATI Radeon HD 3650 AGP Boot?
Feb 20, 2011
I have installed OpenSuse 11.3 . System doesn't boot in NORMAL mode, system boots only in Fail-safe mode. In NORMAL mode i have kernel panic (may be i am wrong, but Caps Lock + Scroll Lock are blinking synchronously during NORMAL boot). ATI Radeon HD 3650 AGP figured on thread Subject because i am sure that the problem is in this video card. 2 weeks ago i have installed ATI Proprietary driver for this card and system successfully boot in NORMAL mode without any kernel panic. You may ask me, "What the problem, install this driver again and have fun!". The problem is that when I install this driver and boot in NORMAL mode video sub system works very slowly. For example one mouse scroll in Internet browser takes 2 seconds to redraw the window. It is not only browser window problem. It refers to all windows. I even can see the wave from up to down on the screen when any window redraws. Very poor performance of 2D video. So , installation of this driver is not the solution.
In the Fail-safe mode 2D video performance is not so cool as at Windows XP but is much more better than in NORMAL boot with proprietary driver installed. Now I have clean installation of system without any drivers installed over distributive. now system configuration:
1. Motherboard: Intel 845D(has on board AC'97 sound, but this sound is disabled in BIOS currently)
2. CPU:Intel Celeron 1.7 GHz.
3. Main memory: 1,5 GB DDR 266MHz.
4. Video card: PowerColor ATI Radeon HD 3650 AGP (512 MB, 64 bit).
5. Sound card: CMI8738.
[Code]...
View 9 Replies
ADVERTISEMENT
May 14, 2011
I can not porpperly boot into live CD. I get the option menu in beginning and when i select the liveCD option it starts loading the kernel and then screen gets garbled. full of very small dots. Its liek the graphics card is not recognised propperly. I've read about similar issue here: ATI Radeon HD 3650 AGP boot problem
but as i see the user's specific problem in taht thread was caused by having an AGP card and on an older version. however my card is PCI. it should boot normally. i haven't tried nomodeset parameter mentioned in that thread, but the card shouldn't need it anyway.
View 5 Replies
View Related
Feb 19, 2011
I have installed OpenSuse 11.3 . System doesn't boot in NORMAL mode, system boots only in Fail-safe mode. In NORMAL mode i have kernel panic (may be i am wrong, but Caps Lock + Scroll Lock are blinking synchronously during NORMAL boot). ATI Radeon HD 3650 AGP figured on thread Subject because i am sure that the problem is in this video card.
[Code]...
View 3 Replies
View Related
Feb 2, 2009
I am running openSUSE 11.0 on a Toshiba laptop with the ATI Radeon HD3650 graphic card. After installing the ATI drivers using the "1-click-install" feature found in the suse wiki, the 3D acceleration seems to be working... sort of.
[Code]...
I haven't tried to launch Compiz. However when I try the OpenGL screensavers, they run fine in the preview but when I test them, they only show in what seems a 640*480 portion of the screen in the top left corner. The rest of my 1200*800 screen is blank.
View 4 Replies
View Related
Mar 15, 2010
I have a Dell 1737 laptop with ATI Mobility Radeon HD 3650. I have the ATI fglrx drivers installed.
All OK.... BUT
I have no hardware graphics acceleration to any application.
glxgears consumes 29% of the CPU to run.desktop compositing consumes 0-50% CPU depending on activity.
running opensuse 11.2 up to date...
View 9 Replies
View Related
Aug 20, 2010
For some time, almost since it came out, I've been using a single Radeon HD 3650 with two (dissimilar) monitors. It's fine and works well with fglrx and openSUSE. ( Although now that I come to think of it, openSUSE 11.3 does only have preview support in my current fglrx. ) I now have a second, identical card. My hardware is:
Video cards: 2x Sapphire Radeon HD 3650
Motherboard: Gigabyte GA-MA790X-DS4 1.0
Also...
CPU: AMD Phenom II X4 940 Black
[code]...
My video card did come, if I remember rightly, with a crossfire bridge but that has been thrown away (not by me). However the motherboard specifications do include support for CrossFireX. I've tried, although with very little understanding of how, to use aticonfig to set up my cards for crossfire. As it stands crossfire is not enabled and aticonfig claims that it does not support this platform:
Code:
# aticonfig --cfa --adapter=all --crossfire=on
CrossFire chain added
Warning: X needs to be restarted before CrossFire changes take effect.
CrossFire chain(s) enabled
[code]....
Is it possible to get this working?
View 2 Replies
View Related
Jun 1, 2011
I'm trying to enable power management on my ATI Radeon HD 3650 video card (GPU: ATI RV635; see my Smolt profile). I'm using the open-source radeon driver (xorg-x11-drv-ati-6.14.1-1.20110504gita6d2dba6.fc15).I've followed the instructions found on the Arch Linux Wiki.In order to verify if power management really works, I've tried to enable the "low" power profile through these commands:
Code:
echo profile > /sys/class/drm/card0/device/power_method
echo low > /sys/class/drm/card0/device/power_profile
I've also added the above-mentioned commands to /etc/rc.local to have them executed at startup.Although this page on the X.Org Wiki says that power management on my video card is supported by the radeon driver, GPU clock frequency doesn't seem to decrease: cat /sys/kernel/debug/dri/0/radeon_pm_info reports
Code:
$ cat /sys/kernel/debug/dri/0/radeon_pm_info
default engine clock: 725000 kHz
current engine clock: 722250 kHz
default memory clock: 500000 kHz
[code]....
Also, enabling dynamic frequency switching through
Code:
echo dynpm > /sys/class/drm/card0/device/power_method
seems to have no effect. how to actually enable power management on my GPU?
View 4 Replies
View Related
May 1, 2011
I've got big problems with ubuntu 11.04 (32 Bit, on Lenovo T500 with ATI Mobility Radeon HD 3650)First of all i have to boot from the installation cd with the option "nomodeset".Also for the first boot from harddisk i have to set this option. After i have installed the proprietary ATI drivers i can boot with the default options but unity won't start....n dmesg i found following messages:Quote:
[ 415.901678] unity_support_t[2357]: segfault at 4 ip b76b2824 sp bfaeee50 error 4 in libGL.so.1.2[b7639000+c9000]
[ 415.905490] unity_support_t[2359]: segfault at 4 ip b75a1824 sp bfd3fa90 error 4 in
[code]....
View 2 Replies
View Related
Nov 8, 2010
I'm having problems with my graphics. I have ATI mobility radeon hd 3650 and I get an issue with desktop effects. They can't be enabled even though the card is supported. I had some trouble with installation and used this thread's instructions: http://ubuntuforums.org/showthread.php?p=9133906. I finally seem to have it installed and configured but I still can't use desktop effects. Also this whole process started because I couldn't get minecraft working getting the GLX13 error.
View 1 Replies
View Related
Jul 19, 2011
As per the thread title, tried both 32 and 64-bit isos, also re-downloaded the isos in case of a problem with them
Fails to enter runlevel 5 (and start kdm), I've tried the usual nomodeset, setting no_kms_in_initrd isn't much help as mkinitrd fails after setting it
Here's the gist of the errormsgs:
Code:
(==) Using config directory: "/etc/X11/xorg.conf.d"
(EE) Failed to load module "fglrx" (module does not exist" (0)
(II) [KMS] drm report modesetting isn't supported
(EE) RADEON(0): Chipset: "AMD Radeon HD 6800 Series" (ChipID = 0x6738) requires kms Some things I've tried:
Blacklisting fglrx doesn't work with vi as it tells me 50-blacklist.conf is read-only even when I use the ! override read-only switch
Tried specifying both the radeon and radeonhd and even vesa drivers in /etc/X11/xorg.conf.d/50-device.conf when trying off a usb pen drive created with imagewriter
As mentioned earlier. tried nomodeset and no_kms_in_initrd to yes
It's a pain as I have tumbleweed on the machine and prior to putting the radeon card in it I would use a live usb drive to backup the system prior to updating, when I had an nividia card in the machine live usb and live cd would both boot no problem so it pretty much has to be something about the way it's handling the radeon card (like trying to load the non-existent fglrx driver regardless of what I do to try stopping that maybe?)
Don't know what else to try though and if I can't get it booting off a live opensuse I can see myself putting another os on it somewhere just for backing up the system before any updates
View 9 Replies
View Related
Jul 16, 2010
I've just performed a fresh installation of openSUSE 11.3. System specs include GA-MA790X-DS4, PhenomII X4 940 AM2+, Sapphire RadeonHD 3670, two monitors. What I'm trying to accomplish is to set up my KDE desktop to (as it did under 11.2) use a multi-desktop multi-output non-cloned setup, so that I can use my two monitors side by side and maximize windows in either one respectively, etc.
So here I am with my newly installed system. Obviously I can't use fglrx, as it doesn't yet support the 2.6.34 kernel, so amdcccle is right out. SaX2, I notice, is gone. I have tried using KDE's built-in configuration tools, but the dual-head setup doesn't persist between logins. Strangely, windows that were open on the second monitor do vanish off-screen, but the monitors return to their overlapped positions so it's useless. Monitor 2 doesn't even retain its resolution setting. As one does, I decided I'd manually edit the X configuration file. SHOCK HORROR! No xorg.conf So what I'm driving at is this: How oh how do I configure my X.org to remember that it has two, quite different, monitors under openSUSE 11.3 ? Sorry if this post is hard to follow, I got very little sleep while trying to sort out the myriad problems I caused myself in upgrading.
View 9 Replies
View Related
Jul 27, 2010
recently I have downloaded opensuse 11.3.tried to install latest version of graphic driver.but after uncompressing it says:
which: no XFree86 in (/home/muhammad/bin:/usr/local/bin:/usr/bin:/sbin:/usr/sbin:/bin:/usr/bin/X11:/usr/X11R6/bin:/usr/games:/usr/lib/jvm/jre/bin)
Error: ./default_policy.sh does not support version
default:v2:i686:lib::none:2.6.34-12-desktop:; make sure that the version is being
correctly set by --iscurrentdistro
Removing temporary directory: fglrx-install.fvzKbN
I have installed kernel sources,xorg x11 headers and gcc.
View 9 Replies
View Related
Mar 7, 2010
I have been having lots of trouble getting my system up and running after I installed a Radeon HD 5850 on my suse machine. I did as they told by uninstalling the previous drivers and installing the new ones as stated in ATI Catalyst™ 10.2 Linux Installer Note.
2)sh ./ati-driver-installer-10-2-x86.x86_64.run
7) /usr/bin/aticonfig --initial
This was all done from a terminal... And I did this for Suse distributions 11.1 and 11.2. Both times my mouse cursor disappeared, but this could easily be fixed by adding the option "SWCursor" "on" option under the Device section.
This was only part of the solution as I still have incredible lag on my windows e.g. when I scroll down a web page it takes incredibaly long to render and you can see it rendering the page in steps from the bottom up. As well as when I drag a window across my desktop it lags behind and you can se it reforming at the new position.
Finally I tried different releases of the proprietary driver. I tried 10.1 and this did not give me the mouse cursor issue, but the window lag still prevails. These are my xorg.conf and xorg.0.log files for my current setup. Opensuse 11.1 and proprietary driver version 10.1. I have an Radeon HD 5850 card.[URL]..
I should add that I am on a private network, and only have the oss, non-oss and packman repositories available. (Is it possible to add the AMD driver repository? Because I have trid and the firewall refuses connection.)
View 6 Replies
View Related
Mar 13, 2010
I tried to install the driver using the easy and hard way, but unfortunately I couldn't install it. When the file manager opens up through terminal after I type in the command using super user mode, I select the downloaded file and it opens it up in kwrite.
View 9 Replies
View Related
Nov 8, 2010
how to install ati drivers for the ati radeon x1200 chipset? i searched everywhere but i could not find a link to a repository for this chipset
View 7 Replies
View Related
Mar 15, 2010
Am trying to install the correct driver for my RV710 Radeon HD4350 grahics card.which version out of these two I should install: * x11-video-fglrxG02 (for HD2000 series and later) * x11-video-fglrxG01 (for Radeon 9500 - X1900)
View 3 Replies
View Related
Apr 20, 2011
I installed openSuSe 11.4 on a Lenovo W500 and noticed this error message upon bootup. The desktop login doesn't make it to the screen. I went into fail-safe mode as root. I know the issue is attributed to the R600_rlc.bin located in /lib/firmware/R600_rlc.bin. I attempt to make some config changes but the file is in binary. It could be a problem associated with the creation of the initrd but not certain. It's a dual-boot system running Windows 7 on the other partition
View 1 Replies
View Related
Jan 8, 2010
I can't print via our network printer (HP DeskJet 3650) which is connected to a WinXP PC on the network. My laptop is wireless connected to the network. My distribution is openSUSE 11.2 and I tried setting up the network printer via CUPS:
Went to http://localhost:631
Add Printer
Device: Windows Printing via SAMBA
Device URI: smb://UMBRELLA/SMOKE/HP3600
Make: HP
Model: HP DeskJet 3650, hpcups 3.9.8 (en)
Printer State: idle, accepting jobs, published.
Then clicked the "Print Test Page" button. At this point the printer actually starts making sounds.. the same sounds it makes when it's preparing to print something. But then, it stops. The printing job is still present in the printer queue at the WinXP PC, but it won't print.
So I looked at this documentation: [URL]
Step 2 from this documentation tells me to install a PPD file.. which I can't find anywhere. It's not on the original HP driver CD, neither can it be downloaded from this page: http://www.openprinting.org/show_pri...P-DeskJet_3650.
Also, I believe I have everything installed:
Code:
serrano@saibot:/usr/share/cups/model/HP> rpm -qa hplip hplip-hpijs foomatic-filters
hplip-hpijs-3.9.8-3.4.1.i586
foomatic-filters-4.0.1-2.1.i586
hplip-3.9.8-3.4.1.i586
View 11 Replies
View Related
Apr 4, 2010
I replaced an ATI Radeon 9550 with a Radeon X1300/X1550, in hopes of better performance.
My System: P4@3GHz, 1.5Gb RAM, Fedora 12, kernel 2.6.32.10-90.fc12.
Faults: Screen refresh is extremely low. Glxgears outputs 25 FPS. Dragging windows around is sometimes really slow.
What I did so far, in hope of fixing it:
1. Installed 'system-config-display', for providing an xorg.conf
2. Did: yum --enablerepo=rawhide update mesa-dri-drivers-experimental mesa*, fixing this, but to no avail...
I cannot find any errors in the log...I don't know what to do...
I am posting my Xorg.conf, Xorg.0.log and Glxinfo through links to pastebin.com
POST UPDATE:
When running GlxGears, I get a bit of motion, and then the gears freeze for 1 second. And this goes on and on. But...if I move the mouse around, I get 1100FPS!
Now I messed a bit with xorg.conf and the "SWCursor" Option, but the above happens when this option is on "true". On "false" there is no 1100FPS, only the freezing loop...
View 1 Replies
View Related
May 24, 2009
I been searching for months on how to get the s-video to work on my pci VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] card. I found a site with instructions.
This is how I got it to work.
I install Debian 5.0 Lenny Desktop
added the Driver "radeon" to my /etc/X11/xorg.conf file
This work and I was able to use my tv as a monitor however when I try to play a video file from totem or vlc all I could get was audio with no video; These files work and played fine in the CRT monitor.
View 2 Replies
View Related
Aug 18, 2010
Dual Booting my laptop and unable to change the Boot Records on the drive. Not because I dont know how, but my primary OS will fail to boot(win7).
I have drive partitioned as follows...
sda1 = Win7 system (default install)
sda2 = Win7 Main (default install)
sda3 = swap
sda4 = Extension (I think thats what its called)
sda5 = / (ext4)
What I need is a boot cd or perferably Grub installed on a 256MB Thumb drive with the options to load the installed system from sda5.
View 4 Replies
View Related
Nov 23, 2010
I tried to install 11.3 on my acer aspire 7530 notebook to have dual boot with xp.
I made 4 partitions: one for xp, and the three for linux were made automatically.Before installation I got the warning that the partition wasn't entirely below 128 gb, I installed anyway to give it a try.
The installation froze at 92% and after the laptop wouldn't boot.
Now I've formatted the hard disk and installed windows on a partition leaving a free un formatted partition of 100 gb.
View 9 Replies
View Related
Nov 4, 2010
Out of curiosity and stupidity, I configured 2 extended partitions to LVM in gparted. Now, I can't boot into X window, and there's only GRUB command line during boot.
View 5 Replies
View Related
Jan 4, 2010
does anyone know that if i can boot from an external hard drive with "openSUSE" installed on it?
how about FireWire, will it work?
i'm trying to set up a triple boot for me newly bought iMac.
View 4 Replies
View Related
Feb 14, 2010
I turn back to openSUSE and install it in my machine (win7 installed first),but i can't boot from win7. openSUSE doesn't boot from win7 (like ubuntu) and i can't see ntfs win7 partition from openSUSE. Why openSUSE is so complicated about dual booting
View 4 Replies
View Related
Sep 29, 2010
I have a Dell laptop with Windows XP installed, and for various reasons (Help: I borked my WindowsXP boot when installing OpenSUSE 11.3) I can not install a GRUB boot loader to the first hard drive (hd0).
I currently have a second hard drive in this laptop with a perfectly working OpenSUSE 11.3 instance, but no way to boot into it. I remember back in ancient times, a common option with Linux distros was to create a boot floppy to boot into Linux rather than installing GRUB or LILO to MBR. Since this laptop doesn't have a floppy drive I'd like to do the same thing with a USB stick. Is there any way to install GRUB (or something similar) to a USB stick? What I am not asking here is whether I can put a full, bootable Linux instance on a USB drive - I only want a boot loader on USB that launches to the appropriate mount point on (hd1).
View 6 Replies
View Related
May 26, 2011
I'm trying to dual-boot Windows 7 with openSuSE 11.4, i was told that i should install SuSE after windows 7 as it takes care of the boot-loader and automatically detects my windows installation and not vice-versa,
But that is not true in my case.
So i had 2 hard disks one had windows 7 installed and one was empty so i decided that i should get openSuSE 11.4 on the empty hard disk and dual-boot it with windows 7 (that i already had installed). Downloaded the DVD, put it on a USB and installed SuSE on the other hard disk normally, it detected my windows installation on my main hard disk but i didn't touch that, only formatted my other hard disk to ext4
After the installation it booted automatically into SuSE, but now every time on a fresh restart the system boots automatically into windows. Methods i have already tried to resolve this and it didn't work:
1. Booted from the DVD and selected an "Upgrade" not "New Installation" so i could boot again into my SuSE installation which did work, checked my "Boot Loader" options from YaST and checked the "Boot from MBR" option instead of the "Boot from root partition" option, That Did NOT work.
2. Used the same method to Boot into SuSE with the "Upgrade" Option opened up the terminal and tried to install grub manually again using this link
[Code]...
View 4 Replies
View Related
Jan 31, 2010
I got the serious problem after update my opensuse 11.2, after update the message appeared and said restart my machine to updates take effect and after restart system doesn't boot GUI workspace it boot into text like space named "Emerald - Kernel 2.6.31.8.0.1 - desktop (tty1)".What can I do to boot my machine into GUI again?
View 4 Replies
View Related
May 23, 2011
I have just installed Squeeze on my laptap with a radeon mobility equipped laptop. When it boots, I see the following message:r600_cp: Failed to load firmware "radeon/RV635_pfp.bin".and some others, too, but it stalls at that point, and I cannot use CTRL-ALT-F2 to get a text-based prompt - in fact, I can only seem to get it back with a ALT-SYSRQ (R-E-I-S-V-B) sequence to force a reboot. It is a multi-boot system, with a windows partition, Ubuntu partition, and the new Debian partition. The Ubuntu and Windows partitions will still boot, only the Debian stalls.
When I boot into Ubuntu, I can see the Debian partition, and can see (for instance) the /var/boot/dmesg file, but it only says:"(Nothing has been logged yet.)"So, being new to debian itself (even though, I know, that Ubuntu has a debian base), how can I make it boot without X, which is I presume, the center of the difficulty? Can I change some file on the debian partition using Ubuntu to get the debian partition to boot in text only mode, and then try to fix the radeon driver?
Alternatively, can I put the proper files for the radeon driver *from* the Ubuntu partition *to* the debian partition and expect it to load and boot correctly? I did, at one point, download and install the proprietary ATI driver files on Ubuntu, so can I put them in a proper place on the debian install?
View 5 Replies
View Related
Jun 24, 2010
I'm new to OpenSuse and also fairly new to Linux in general. I installed OpenSuse 11.2 on a secondary machine and I really like it. However, during booting it stops somewhere half way, giving me only a black page but with a functioning cursor arrow. I can't do anything with it though. I re-booted in recovery mood and managed to boot up as root using the command 'startx'. How can I get back to "my own" log-in from here, with my own settings etc? There's obviously something missing during boot-up but where do I look?
View 5 Replies
View Related
