General :: Does Not Recognize - No Scanners Detected - Please Check Your Scanner Is Connected And Powered On
Aug 11, 2010
I have HP Scanjet 3770. UBUNTU 10.04 installed on my desktop. HPLIP also installed. This scanjet working well in Windows Xp but in ubuntu SimpleScan does not recognize it.
It shows:- No scanners detected Please check your scanner is connected and powered on.
I Also visited [url] & found as below-
ScanJet 3770 Unsupported. While an external binary-only backend exists, it works only on Linux i386. Therefore the scanner is unsupported on other platforms.
View 2 Replies
ADVERTISEMENT
Jul 11, 2010
I just received a Canon Pixma MX320 as a gift.
I am currently running the Ubuntu 10.04 OS
I was able to get the printer up and running by downloading the printer driver for debian linux (3.1) from the Canon site without any problems.
Unfortunately I am not having the same luck with the scanner.
I tried downloading ScanGear MP for Linux (deb) (1.3) from the same Canon site but have not yet been able to get the XSane Image Scanner to recognize this scanner driver for my Canon.
View 2 Replies
View Related
Sep 7, 2010
I've installed XSane Image Scanner. When I first opened it, it searched for my scanner and didn't give any error messages, and it had my scanner model in the heading of the scan window. But when I hit the scan button, it gave me saying, "Failed to start scanner: error during device I/O.I closed everything, and opened XSane again. This time it said there was no scanner available. The scanner is plugged into the USB port and uses that for both power and data. It's a Canoscan Model N650U.
View 9 Replies
View Related
Mar 17, 2010
After downloading and installing iscan and run it i see this message:
Could not send command to scanner. Check scanner's status.
After command sane-find-scanner:
And this message is result of scanimage command:
No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages).
View 4 Replies
View Related
Apr 9, 2010
Have Karmic 9.10 ,Changed from Epson RX595 all in 1 (uses a ton of ink)Got the Lexmark Pro 805 3 in 1 because it says it supports Linux and the ink cartridge only cost $5 downloaded drivers and printer works but using Xsane Image Scanner error reports
'Lexmark_1_0_0:libsub/001/009': Device busy Using Image Scan - reports Could not send command to scanner Check the scanner status. The RX595's scanner drivers had to been manually instatlled,, in the Printer box the Lexmark shows available..
View 3 Replies
View Related
Feb 25, 2011
I want to write a script and put it in /etc/rc.local so that
if lan is connected then
rfkill block all
else
nmcli con up id 'Network id' --nowait
How should I write the if part and how should I check for "lan is connected" ?
View 1 Replies
View Related
Sep 13, 2010
I have an Epson perfection V100 Photo scanner. When I open any programit will not detect the scanner. Simply plugging in the scanner and crossing fingers does not work.sane-find-scanner returns the following:
Code:
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
[code]...
View 6 Replies
View Related
Jan 13, 2011
I want to set up a home / file / torrent / web / print server at home. I am using a dell optiplex gx240 and my printer is a Epson dx8400. I was wondering if it is possible to use the printer and scanner connected to the server. Has anyone done this before? I hope to print from any computer in my house. Scanning would probably be the hardest part I guess.
View 2 Replies
View Related
Mar 24, 2011
I have a router Asus RT-n16 where i've connected my EPSON DX5000. I've configured the printer function, adding the printer as AppSocket, adding router IP and port 9100 (socket://Router_IP:9100), but now i can't get the scanner function.
I've installed packages from here[URL].do (iscan) and adding on /etc/sane.d/epkowa.conf the line
Code:
net 192.168.1.1 #my router ip
but it's not working. When i run scanimage -L i get this message:
No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). The scanner option worked fine when my printer is directly connected at my computer.
View 2 Replies
View Related
Jan 30, 2011
I have a Brother mfc-8890dw that is attached to my local area network.I can ping the static ip address of the printer and receive a reply. I can print from all applications.I cannot scan. I did modify the rules files but that only appears pertinent for usb attached devices. What do I need to do to get XSane to recognize my Ethernet attached scanner/printer?
View 2 Replies
View Related
Nov 16, 2010
Just upgraded from Fedora 13 to 14. My network Brother MFC-9440CN will not operate (worked fine in F13). Error message from both Simple Scan and Scanner Tool (xsane) states "No devices available".
View 14 Replies
View Related
Jun 1, 2011
I have an epson stylus sx425w which is a printer/scanner. ubuntu found and installed a driver for me and im able to use the printer fine but for some reason the scanner just isnt working. if i use the simple scan software it says connect a printer and if i press the scan button on the printer and select usb it says connection problem.
i saw a post about this already for ubuntu 10 or 9 and they provided a link for a newly released driver which turned out to be the drive ubuntu installed automatically and that hasnt fixed my problem.
anyone know what the cause could be and how to fix it?
View 1 Replies
View Related
Dec 6, 2010
I added myself to the scanner and saned groups, however scanimage -L only detects the device when run as superuser. I think this may be related to [URL].
root@icecream:/home/discord# scanimage -L
device 'epson2:/dev/sg0' is a Epson GT-9800 flatbed scanner
discord@icecream:~$ scanimage -L
No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages).
View 1 Replies
View Related
Mar 11, 2011
I've got a SCSI scanner that is being detected by the kernel on Fedora 14, but XSane does not see it. If I run "sane-find-scanner" it says that noSCSI or USB scanners are found.The scanner is a Cacham Splendeur 3024, model VM3552. I believe this scanner is the same as the Relisys Scorpio VM3552. In /var/log/messages, the following entries show up as soon as the scanner is warmed up:
Code:
Mar 11 13:34:45 dt kernel: [22595.116042] usb 4-2: new full speed USB device using uhci_hcd and address 41
[code]...
View 4 Replies
View Related
Mar 7, 2010
Have an Epson Expression 1640 XL A3 scanner (usb & network interface card). Bus=0002 Device=004 its usb ID is 0x04b8 0x0109 I have never been able to connect the scanner using the network - if anybody can advise, I would be very grateful. Quite happy to use this if usb is going to be a problem The scanner has worked very well through the usb and wask working well with 9.04(32bit). I have bought a new machine and did a fresh install of 9.10 (64bit) and the scanner is not detected.
xsane detects my webcams (vl4:/dev/video*)but no scanner Have run sudo xsane-find-scanner - only the webcams are detected Have edited /etc/sane.d/epson2.conf - added scanner usb ID, and added the lines:- usb /dev/usb/scanner0 usb /dev/usbscanner0 as advised in one of the threads in this forum sudo scanimage -L gave this-
WARNING: Unhandled message: interface=org.freedesktop.DBus.Introspectable, path=/, member=Introspect
device `v4l:/dev/video1' is a Noname Creative Labs Webcam Pro Ex virtual device
device `v4l:/dev/video0' is a Noname Logitech QuickCam Pro 4000 virtual device
[code]....
Do I need to select M for these three modules?
the following had [M] -
USB Printer support
Microtek X6USB scanner support
It looks like the scanner module has not been loaded, and possibly the usbfs yet usb webcam and card readers are accessible. I have tried to keep outputs relevant & short. If I have omitted anything, you would like full results or any other information.
View 1 Replies
View Related
May 7, 2010
Using xsane with HP scanjet 3970 scanner. It used to be that when I plugged the scanner in and started the xsane a window would come up asking if I wanted to use my HP scanner or my Hauppauge video card. Well, that window no longer comes up and the Xsane wants to use my video card. When I try to "scan" the program closes and all the windows associated with it disappear.
View 1 Replies
View Related
Mar 6, 2011
I have a problem here where sane no longer detects my scanner.
Code:
lsusb
reports
Bus 007 Device 002: ID 03f0:5b17 Hewlett-Packard
Code:
sane-find-scanner
reports:
found USB scanner (vendor=0x03f0 [Hewlett-Packard], product=0x5b17 [HP Color LaserJet CM2320fxi MFP]) at libusb:007:002
Code:
scanimage -L
reports
No scanners were identified. xsane reports no devices detected (I have it in French, "Aucun p'rif'rique disponible"). I get the same when I launch xsane as root, so I doubt it is a usb-rules issue. It used to work; I checked /proc/bus/usb, but that is empty.
View 3 Replies
View Related
Aug 2, 2010
I have an epson cx7800 printer/scanner that 11,3 doesn't detect on USB. I tried Yast-Hardware-printers and Yast-Hardware-printers and nothing is discovered/detected.
Are there repos for this stuff and is there a tutorial like the one for graphic card theory I could peruse?
View 3 Replies
View Related
Nov 13, 2015
I noticed that Debian 8 has a significant bug related to detecting presence of display(s). Today, I woke my computer from sleep while the LCD monitor was unplugged from power (the monitor is connected via DVI) then I powered the monitor but nothing was displayed. Next, I connected another monitor via HDMI and both screens started working. However after disconnecting HDMI cable from the second monitor the first one with DVI stopped showing anything. The conclusion of this situation is that HDMI monitor must be connected all the time.
I thought that this is caused by graphics driver, but I experienced the problem on different machines, one with nvidia driver and DVI, and the second with default free driver and DisplayPort.
I just checked that this is related to KDE. After switching to console using ctrl+alt+f1 the screen turns on, but when I am going back via ctrl+alt+f7 the screen disappears.
View 2 Replies
View Related
Dec 2, 2010
I just installed Fedora 14 i386, and Fedora can see the wireless network just fine. I try to connect and nothing happens. It asks for the PSK constantly (yes, I promise I'm entering it correctly), even after I enter it correctly (I guarantee). I've searched around here a bit, but due to my limited knowledge in linux system I can't figure it out
1.
Code:
lsusb
Bus 002 Device 002: ID 1737:0071 Linksys WUSB600N Dual-Band Wireless-N USB Network Adapter
2.
Code:
iwconfig
lo no wireless extensions.
[Code]....
View 1 Replies
View Related
Jan 28, 2010
I have a Prowler weather station connected via USB. Ubuntu does not recognize this. I am wanting to work with the data on the weather station on my computer. I would assume that the problem lies within 1941:8021 Dream Link USB Missile Launcher.
Terminal readout is:
user@user-laptop:~$ lsusb
Bus 005 Device 002: ID 1941:8021 Dream Link USB Missile Launcher
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[code].....
View 14 Replies
View Related
Apr 23, 2011
I have installed Imgburn and it wont detect my cd drive, I configured wine and everything and no matter what I can't get it to recognize my driver, what am I to do?
View 9 Replies
View Related
Aug 15, 2010
I've installed Ubuntu 10.04 32 bit version(dual OS) on my 64 bit Pentium core2 duo 2.2GHz processor. Everything seems to be working fine except it's not getting connected to wireless network, although it's detected the network .It was working fine(got connected to wireless network) when I had installed the same OS via virtual machine.
View 9 Replies
View Related
Apr 16, 2011
Well, i have some applications that i use everyday so i add them to the startup applications, but they require Internet, otherwise the configuration is lost. I'll like a command that first check if i'm connected to Internet and if i am, launch the app. If not, don't do nothing.
This is a problem because for some reason everytime i turn on my laptop the wireless adapter doesn't turn on automatically (it always did when i was running windows).
View 4 Replies
View Related
Sep 7, 2010
I've recently salvaged a computer I found gathering dust in the basement and decided I'll have it running on Fedora (I have a summer studentship coming up that needs Linux use so I thought I'd best start learning!). Following a clean install, Fedora can see the wireless network just fine. I try to connect and nothing happens. Half of the time it will ask for the PSK (yes, I promise I'm entering it correctly) and the other half of the time it will just stop. When it does ask for the PSK I enter it (correctly) and it will ask me again... and again.
Quote:
uname -r
2.6.33.3-85.fc13.i686
Quote:
lspci
00:0b.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
[Code]....
View 11 Replies
View Related
Mar 20, 2010
Yes, I was all excited when I plugged in an old dusty PC and found it still alive with a 32 gig hard drive & 260 Megs of RAM with an open slot for more memory, fit for my first Linux system. Then I navigated to device manager and found it was powered by a celeron, which was kind of a bummer.Anyway, can I get by with this setup? I'd like to use the slackware distribution, and my main purpose is to learn to administer a LAN, starting w/ 2 local clients, & a server that also runs Apache.
View 14 Replies
View Related
May 31, 2011
I upgraded F14 to F15; However, F15 no longer recognizes my 3 sata disks connected through Marvell controller. The controller is an integrated Marvell chipset 88SE6480. The controller has its own manufacturer driver but it was intended for RHEL 5.4 (mv64xx) and installation of this driver fails to generate mv64xx driver.
View 3 Replies
View Related
Mar 27, 2010
I've been getting a message on my monitor where "Input not supported" is floating around. This only happens when I manually turn the monitor off and then later turn it back on. Leaving the monitor on and allowing it to go to the screen saver doesn't seem to cause the issue (but I prefer to turn the monitor off if I'm going to be away from the computer for any length of time).
Specs:
Acer X203w monitor
Radeon 9600 Pro Video card
Linux Mint 8 (Helena)
Resolution 1680 x 1050 (16:10 - Preferred native resolution for the monitor)
Refresh Rate 60hz
[Code]...
I just had it happen again. I tried unplugging the DVI cable from the back of the computer and then plugging it back in. The monitor then displayed the desktop properly. I'm not sure if that makes a difference or not in what I may need to change settings-wise.
View 1 Replies
View Related
Feb 10, 2010
I am trying to write a script to turn my HTPC off automatically and turn it back on again at a specified interval.
I've got the turn on off bit sorted using /sys/class/rtc/rtc0/wakealarm but I want the script to not turn the machine off if say something is downloading, I am currently watching something etc and i dont think I will have any trouble with that.
But what I would really like to be able to do is tell if my TV is currently on. I dont think anything x11 related would work here and this may not even be possible. Does Ubuntu "know" if it's display device is powered on or not? if so can I interrogate this somehow?
View 5 Replies
View Related
Apr 20, 2010
Ive been wondering about an alternative method for checking to see if an external monitor is connected.
Currently I am using:
Code:
#!/bin/bash
EXTERN=VGA1
if $(xrandr --prop |grep -q "$EXTERN connected");then
echo -e "$(echo $EXTERN | tr -d [0-9]) is e[1;32mconnectede[0m"
else
[Code].....
So, what I am asking is, is there a way to ignore/over-ride compiz's texture size check, a different way to query xrandr, or is there a completely different method I can go about checking if an external monitor is connected?
View 3 Replies
View Related
