Fedora Networking :: Scan From Network Multifunciton Device - Using Scanner
Jan 9, 2011
I have installed a new network multifunctional device Samsung CLX-3185FN using the drivers provided by the manufacturer (Samsung Unified Driver). The printing over the network works fine, I can administer the device using browser. The only problem I have is using scanner over the network. It works fine if I disable firewall, but is blocked with firewall enabled. I can not figure out which ports or port-range I must enable for this scanner. Do you have any information on this one or how can I found out the necessary ports to open?
View 3 Replies
ADVERTISEMENT
Apr 9, 2010
Have Karmic 9.10 ,Changed from Epson RX595 all in 1 (uses a ton of ink)Got the Lexmark Pro 805 3 in 1 because it says it supports Linux and the ink cartridge only cost $5 downloaded drivers and printer works but using Xsane Image Scanner error reports
'Lexmark_1_0_0:libsub/001/009': Device busy Using Image Scan - reports Could not send command to scanner Check the scanner status. The RX595's scanner drivers had to been manually instatlled,, in the Printer box the Lexmark shows available..
View 3 Replies
View Related
Apr 15, 2011
I'm using a scanner with Fedora. However, linux does something that is undesirable; It turns off the scanner light, everytime it does a scan, which the HP software, which comes for windows, doesn't do. The result? The light never warms up enough and all the images come with a blue tone on them. Only after using the scanner a few times, the light warms up enough and the images start getting their true colour.The question is, can I somehow force the light to stay on, even during scans, like it happens when I am using Windows? Or not? Anyone has ideas?
View 3 Replies
View Related
Jul 22, 2011
OS: CentOS 5.6 yesterday i bought a new HP network printer/scanner (OfficeJet Pro 8500). It installed correctly using hplip drivers. I can print and scan without any problem, very nice and fast device. I did some research where the information where the device port is stored in sane, but cannot find anything. I tried to remove my old network device port for my Brother scanner, but did not find the config file where this information is stored. Neither /etc/sane.d/* nor ~/.sane/xsane/* contains this information.
View 14 Replies
View Related
Jan 7, 2010
I just added a 2 port network card to a system that is running Fedora 11, but it is INACTIVE. I open the Network Device Control to activate it but there is no network ports in Network Device Control. It is empty.It looks like the system recognize the card and loaded correct driver.
View 4 Replies
View Related
Jul 13, 2011
I just picked up a second hand printer/scanner for free cuz I fixed it (which wasn't a lot of work). It works perfectly over wifi except that simple scan doesnt pick it up. I would just use a cable but we don't have an extra one and I don't get paid until friday. Anyway to get simple scan to work over wireless? The printer is an HP Photosmart C7280 all in one.
View 3 Replies
View Related
Jun 14, 2010
I have used ubuntu in the past but had a lot of hardware issues with it and unfortunately moved back to windows (( BUT i have tried Ubuntu again and all seems to work great except wifi My wifi connection is sort of working because when i run SUDO IWLIST SCAN it does pull up all available networks. But in the network manager icon on the panel i left click but i see no networks and can't connect to anything. I WOULD LOVE TO keep Ubuntu and use it permanently but I must get wifi working or else this won't be possible.
View 4 Replies
View Related
Oct 17, 2010
Recently, I bought the HP Officejet 4500 especially because of the automatic feeder for the scanner. The device is not supported by Fedora, but I found the driver for it at the HP driver site for Fedora 11 and / or 12.Now, I have two questions. First, I wonder why these drivers are not part of a Fedora distribution yet. Is there still some issue with it going on (something related to my second question or something completely different)?Second, the software (Sane) doesn't recognize different sheets of paper. When I place some 20 sheets of paper in the automatic feeder, the scanner scans them all, but only the first sheet is processed by Sane.Now, I saw that Sane in Fedora 13 is different than in Fedora 11 or 12. I expect it is improved, but I have not been able to work with it yet. Can I expect that it does recognize different sheets of paper from a scan with an automatic feeder?
View 2 Replies
View Related
Sep 8, 2015
I was wondering if there is anyway to adjust scanner settings less not plugging in a scanner with using Simple Scan?I recently found out (sadly) that I could change the DPI settings for document and picture scans when my USB wasn't getting the scanner.Gave a prompt notification bar above and asked me to select scanner (which I replugged it in) and was able to do the settings.Is there a shortcut or command I can use to trigger this any time I need to?
View 0 Replies
View Related
Jan 31, 2010
my all-in-one Epson scanner does not work. I tried to install the iscan drivers (free and/or proprietary) via repository and/or via Avasys website, but nothing happens: the scanner is not recognized. I use Gnome and openSUSE 11.2
View 3 Replies
View Related
Sep 21, 2010
I have just installed ubuntu 10.04, and now trying to get all the hardware working. The HP PSC2170 printer scanner will print, but nothing happens when I try to scan.
View 2 Replies
View Related
May 14, 2011
Ok, so a few weeks back my 6 year old daughter wanted to scan a picture she had made for a school project, I hadn't used my AGFA snapscan e20 for years, Infact it had been in a box for more than 5 years.
anyhoo I thought I'd give it a go and with some doubt plugged it in. Much to my joy and my daughters joy it just worked, there was life in the old dog still So two or three weeks on after I've installed a kernel update as well as others on my daughters Dell Optiplex GX620 Ubuntu 10.04 LTS (2.6.32-30-generic #59-Ubuntu SMP), my multi operating system literate 6 year old has drawn another master piece and popped it in the scanner only to recive the following error from simple-scan
What I'd like to know is,
1, How do I remove the entry for the scanner in simple-scan (ahh the old reinstall never fails)
2, why am I getting nothing back from my tail
3,Why did it break in the first place?
4, how to fix it (if not with a reinstall)
Please help as I don't want to break the "My Dad can fix anything" illusion my daughter has just yet.
View 8 Replies
View Related
Aug 14, 2009
I installed ZTE MF 626 modem in my F10 with kernel 2.6.27.12-170, i run usb_modeswitch and so far things happened normally. Watching through /var/log/messages it says that F10 detects two port device for this modem: ttyUSB1 and ttyUSB2, and in the sequence it disable port ttyUSB1 BUT Network Manager still set this port.I mean, when i connect via wvdial appointing to ttyUSB2 i get connection, but Network Manager fails to do it appointing to ttyUSB1. How to change device port in Network Manager?
View 1 Replies
View Related
Feb 10, 2009
Whenever I try to scan documents (OpenSuse 11.1) with any of the available tools (such as scanlite, kooka, or xsane), I can only scan in color. Moreover, the result is basically unusable. I shows a turquoise background of differing intensity at various places. Why isn't there a possibility to scan black and white, grayscale, etc.? Seems like scanning still is a problem in Linux. I really don't want to have to "fall back" to M$-Windows for scanning, but that seems to be the only solution at the moment
View 8 Replies
View Related
Jan 9, 2011
I installed squeeze on my eeepc 1015ped and downloaded the correct firmware-brcm80211 drivers but every time I scan for my network using iwconfig wlan0 scan or wicd, my computer completely freezes. I previously had a solid install running xmonad, and wicd was working like a charm (using the same broadcom driver) but i tinkered too much with it and decided to do a fresh install. I haven't quite run into a problem like this before.
View 2 Replies
View Related
Dec 28, 2010
It seems that they are not shown under xev ...Someone knows if old scanner, can be detected in terms of button pressing ?[URL]button pressing does not show up into deamon.log
View 1 Replies
View Related
Sep 1, 2009
I have recently installed Fedora11 and have managed to get the printer side of the above multifunction machine working but not the scanner . The computer recognises the scanner and sane, xsane, sanelib's etc are all installed . When I try to open it it gives the following:
Failed to open device 'brother3:bus5;dev1': Error during device I/O
View 6 Replies
View Related
Jan 19, 2010
I'm looking for a virus scanner to scan some removable media (USB drives, mp3 players, etc). Since there's so many choices to choose from, can anyone recommend any?
I've heard a lot of people recommending clam av, but everything I've read suggests that clam av is better used for scanning e-mail servers and not home desktop application...
View 1 Replies
View Related
Jul 6, 2010
scan my network and check for files within a LAN, in a mixed Linux and Windows environment.Something like LAN spy for Windows. Is there a package or program like that for Linux?
View 2 Replies
View Related
May 13, 2010
I just started messing with the networking tools in Linux, and I've discovered that when I run an intense scan in zenmap on 192.168.1.1-254, the network crashes. By network crash I mean - All clients on the network lose connectivity.
View 12 Replies
View Related
Jul 22, 2009
Having trouble with wireless and FC11, eth0 is ok. When I try to activate wlan0 through system-config-network 1.5.97, I get msg: Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Invalid argument. Determining IP information for wlan0... failed. This is a compaq laptop.
<uname -r>
2.6.29.6-213.fc11.i686.PAE #1 SMP Tue Jul 7 20:59:29 EDT 2009 i686 athlon i386 GNU/Linux
<lspci>
The wireless card is Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter
(rev 01)
View 7 Replies
View Related
May 1, 2011
I use fedora 14 and when I'm trying to run the network service on my system it gives me the following error -
# service network restart
Shutting down interface eth0: Error: Device 'eth0' (/org/freedesktop/NetworkManager/Devices/0) disconnecting failed: This device is not active [FAILED]
Shutting down loopback interface: Error: Device 'lo' not found. [FAILED]
Bringing up loopback interface: [OK]
Bringing up interface eth0: Error: Connection activation failed: Device not managed by NetworkManager or unavailable [FAILED]
RTNETLINK answers: File exists
RTNETLINK answers: File exists
RTNETLINK answers: File exists
RTNETLINK answers: File exists
RTNETLINK answers: File exists
RTNETLINK answers: File exists
RTNETLINK answers: File exists
RTNETLINK answers: File exists
RTNETLINK answers: File exists
And whenever I try to activate the device in graphical mode again it shows the above same error.
View 6 Replies
View Related
Feb 3, 2010
i have a hp 6500 e709a printer. have configured for network printing and would like to use the scan facility.i have tried to scan from the printer but it does not find the computer. the hp documents mention advanced firewall information on incoming udp ports and tcp ports etci believe it is with my machine as my son has a windows box with the hp software and i have managed to scan from that machine.
View 4 Replies
View Related
Feb 1, 2011
I use CentOS for the servers I am responsible for. This time, I inherited a piece of hardware that CentOS refused to boot up on, so I installed Fedora Core 14. I have NIS and autofs working -- mostly.The home directories reside on an EMC network storage device. The problem is that when I login as a regular user, all the files under the home directory are owned by nobody/nobody, instead of user/group. I believe this has something to do with NFSv3 vs. v4, but I have yet to find the right trick to fix it.
[Code]...
View 2 Replies
View Related
Feb 11, 2009
i am having problem in downloading and installing nmap network scanner program in my fedora 10 machine...can any body help me from where i can download and install nmap using command line or ssh session on my fedora machine...
View 4 Replies
View Related
Jul 11, 2010
I just received a Canon Pixma MX320 as a gift.
I am currently running the Ubuntu 10.04 OS
I was able to get the printer up and running by downloading the printer driver for debian linux (3.1) from the Canon site without any problems.
Unfortunately I am not having the same luck with the scanner.
I tried downloading ScanGear MP for Linux (deb) (1.3) from the same Canon site but have not yet been able to get the XSane Image Scanner to recognize this scanner driver for my Canon.
View 2 Replies
View Related
Jan 26, 2010
I just bought an hp 6500 wireless printer, and after taking 5 minutes to set it up (amazing how easy it is to get hardware working that supported by Linux) I was happily printing...But- I haven't managed to get it to scan from my desktop pc running 9.04. Tells me no device is found. I added the printer to a laptop running 9.10, and it scanned perfectly straight away...
I've been through the Ubuntu help documentation and haven't found a solution.I think that maybe Turbo Print (for our old Canon printer) might have messed something up. I had to uninstall Turbo Print to get the printer to work (it hijacked Ubuntu's built in printing stuff).
View 2 Replies
View Related
May 1, 2010
The one thing that has stopped me switching over to Ubuntu was getting my scanner to work. I finally resolved this issue. Here are the set I followed to get it working. When trying to scan with XSane I would get the device not found alert. Using the sane-find-scanner command would find the scanner as a USB device. found USB scanner (vendor=0x04b8, product=0x0851) at libusb:001:006 I amended the "rules" file for xsane /lib/udev/rules.d/40-libsane.rules added the two following lines
[code]...
Now I have a fully working colour scanner, bye bye windows
View 6 Replies
View Related
Apr 20, 2010
I just got a new scanner HP Photosmart C4640 and tried to set it up on Ubuntu 8.10SANE has it as supported, but I can't scan.Printing works fine. when I run xsane I get
Code:
Failed to open device 'v4l:/dev/video0': Invalid argument.
Poking around I found ScanningHowTo page. But I was unable to find the .fw, .usb, or a PPD
[code]....
View 3 Replies
View Related
Sep 14, 2010
I have the above bt dongle and I am unable to get the device to scan for remote devices. The dongle and bluetooth software is recognized and from a system point of view is working. Using Suse 11.3 64bits
[Code]...
When I scan the blue led comes on solid and goes back to blinking afterwords but nothing is found. I did try another adapter and the bluetooth worked. BTW The Bluedevel application is real nice and works much better then the kdebluetooth app,
View 1 Replies
View Related
