I know this question was asked hundreds of times,but I sy=till can not fix my wireless. On the HP2133 with openSUSE 11.3 I have wired but no wireless connection. The driver is ssb On Terminal I see
joseph@linux-t2w8:~> /usr/sbin/iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit:7 RTS thrff Fragment thrff
Power Managementff
I'm on a Dell Latitude E6500, and I'm switching from Windows 7 to Slackware 13.1; I've never used linux before. I'm trying to set up wireless internet, and it doesn't seem like there's any standard way of doing it for my system. When I run the "lspci -v" command, I find this:
I installed OpenSUSE 11.3 with disabled WLAN (otherwise the installation process didn't start). Now the system boots only in Safe Mode with enabled WLAN card (when the WLAN card is disabled it also boots in normal mode though). But even if I try to configure the WLAN card in Safe Mode, the system doesn't boot next time (in Safe Mode) until I add "brokenmodules=ssb" parameter. As I understand after reading this forum I should install a firmware/driver, but there is no install_bcm43xx_firmware script in /usr/sbin directory.
I have installed b43 with the install script and I can see all wireless networks fine, but NetworkManager just keeps asking me for the WPA passphrase, despite it being correct. I tried disabling WPA on the router, but then the connection hangs at "Configuring interface" instad. I also tried with ifup, but I'm not sure I configured everything correctly. I don't get any smarter from the NetworkManager logs, maybe someone else can decipher them? tail -50 when connection doesn't work:
Code: Apr 18 17:00:11 jan NetworkManager[1291]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete. Apr 18 17:00:11 jan NetworkManager[1291]: <info> Config: set interface ap_scan to 1
I have a Dell Vostro 1500 that has a Broadcom BCM4312 wireless card installed. I do not have access to a wired connection to the web so any thing I have to install is a download on my windows machine and then transfer that to the debian machine. I just finished installing Debian Squeeze but can not get my wireless card to scan for any networks. I found a tutorial at [URL] and followed the steps there. Finding all the dependances and installing them one by one (took me all day). My wireless card still will not scan for networks. After doing a 'sudo ifconfig eth1 up' it still will not scan for networks.
Output from ifconfig: raygo75@RayGo-2:~$ sudo ifconfig eth1 Link encap:Ethernet HWaddr 00:16:44:9b:e9:cc inet6 addr: fe80::216:44ff:fe9b:e9cc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 Base address:0xc000
How do I get around this? It wants to get something from [URL] and I do not have internet access. It looks to me like it just wants to download the wl dirver, again, which I have done in the previous instructions I found. I am a retired UNIX (hp-unix) administrator so I know my way around the system.
I recently purchased an Acer eMachines E525 laptop, and currently have it dual booting Windows 7 and Fedora 12 x86_64 with the 2.6.31.5-127 kernel. I've been completely unable to get the wireless card working in Fedora (it works fine in windows).
lspci lists the following about the wireless card: Code: Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) so I assume it's a BCM4312.
So far I have tried downloading the driver from [URL] and then trying to install it according to the accompanying readme file: [URL]. However, when I try to make the driver, I get the following message:
Code: KBUILD_NOPEDANTIC=1 make -C /lib/modules/`uname -r`/build M=`pwd` make: *** /lib/modules/2.6.32.10-90.fc12.x86_64/build: No such file or directory. Stop. The Readme says that if I get this kind of error, I need to install the "kernel-devel" package, but I have this installed and it still returns the same error.
I have also tried following the fw-cutter instructions for fedora from [URL], but it still doesn't work. I realise there's the option of using ndiswrapper, but I gave that a shot with Fedora 11 on the same machine and had no luck, and I'd really like to see whether any of the other options work before going down that route.
I am having a problem while connecting to a D-Link Access Point with Multiple ESSID. It keeps saying activating but in the end nothing. I am using KnetworkManager & there is no Encryption on the Access Point.I am able to get connected with another machine using windows.Here is my hardware info:
0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card [1028:000c] Kernel driver in use: b43-pci-bridge & the logs: Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.188245] wlan0: authenticate with f0:7d:68:17:e5:a4 (try 1) Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191262] wlan0: authenticated Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191501] wlan0: associate with f0:7d:68:17:e5:a4 (try 1) Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.194008] wlan0: RX AssocResp from f0:7d:68:17:e5:a4 (capab=0x421 status=0 aid=1)
I have been upgrading (upgrade from 11.3 then fresh install to 11.4) and as usual with Broadcom I have problems. On 11,3 I used the Pacman STA and was working fine. for 11.4, I suppose that my BCM4312 will be supported after installing the b43 driver. It actually woks, few seconds (but never had time to verify) Some background
lspci gives 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Using KDE network manager I can see the wifi AP around, including mine, the problem is when I wan to connect, using WPA2 (TKIP + EAS), I have the right password (I can connect from another station), but when I try here it keeps coming back asking from password .. (I use the kwallet, but that should be out of scope) .. Basically it always fails..
I had Karmic a while back, but i got rid of it becasue of my Bcm4312 Wireless Card would not recognize the STA driver, or bcm43xx.In that time i learned a bit of command line stuff. anyways now that I have my internet working, I was just wondering What I could do with ubuntu. I am interested in the command line and Programming. Where could I learn more about the 2 subjects?
I've just installed Ubuntu on 2 computers, and I'm new to it. However I'm not new to computers. The problem I'm currently running into on one of the computers is that the wireless will not detect any connections, despite there being many. The computer is a HP Compaq v6203AU using the wireless card Broadcom BCM4312 [14e4:4312]. I've went through dozens of walkthroughs, encountering errors in every single one of them, I've spent 8 hours on this one problem and extremely frustrated. It seem to be a problem with the driver that comes as default, and I'm lost at what to do.
The terminal command "lspci -nn | grep 14e4" returns the following: 03:00.0 Network Controller [0280]: Broadcom Corporation BCM4312 802.11a/b/g [14e4:4312]
ifconfig returns the following: eth0 Link encap:Ethernet HWaddr 00:23:8b:b2:ab:d3 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0x8000
I am new to Linux, nevertheless Ubuntu. I have Lucid Lynx on my laptop, with Windows Vista 32 bit along side of it. I have done some research, and found out thathe wireless connector on my laptop, a Broadcom BCM4312, doesn't work with Ubuntu 10.04. I know that I need a driver
I have a problem with the built-in wireless-card of my laptop. I can connect to the wireless DSL-router using wicd (wicd-1.7.0-486-2 from /extra), wicd reports that it connects and obtains an IP-address. It then changes the status to connected. Immediately after that (may be a second later) the status changes back to disconnected and I can't reach the network.
Here some specs: Kernel: self-compiled 2.6.37-6-generic, the only option I changed from the standard generic config was to enable PAE, but I also tried it with the standard generic kernel and the huge kernel. Wireless card: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Firmware installed with the packages from Slackbuilds.org: network/b43-fwcutter network/b43-firmware. The wireless card is working correctly under Debian, so I think this is not a hardware issue.
I have a problem here with my updated kernel. I'm currently using Fedora 14 kernel 2.6.35.9-64, and my wireless card Broadcom BCM4312, which had an issue before with Linux distros, is working fine already, thanks to the kmod-wl software driver. My problem now is this, after updating to kernel 2.6.35.10-72, fedora does not boot, and I noticed that the wireless card is the only thing not activating, compared to the working kernel. And when i looked at the log of the bootup (pressed right arrow key), I saw this:
I posted earlier and got no response, so here i go again. I installed openSUSE 11.3 KDE, it all works fine but the wireless doesnt work and i cant connect to the internet at all, i don't know how to, and i don't even know if the proper drivers are installed. I posted this in the last thread:
"i ran this this command in ubuntu:
Code: lspci | grep -i network came up with this result:
I just installed Ubuntu 11.04 on my Dell Mini 10v and for some reason I just realized that my wired network connection is not working for some reason. And not in windows either. But my wireless works in windows. So I have downloaded the latest Broadcom STA wireless drivers for linux and have tried to follow this tutorial to install it. But when I get to:
make -C /lib/modules/<2.6.xx.xx>/build M=`pwd` clean I can't get it to work. It says:
make: Entering directory '/usr/src/linux-header-2.6.38-8-generic' scripts/Makefile.build:44: /usr/src/linux-header-2.6.38-8-generic/pwd/Makefile: No such file or directory make[1]: *** No rule to make target '/usr/src/linux-header-2.6.38-8-generic
Dell Studio 1735 w/BCM4312 WEP fails to connect even though I'm using the 10 character HEX key. It connects fine when there's no security on my Linksys WRT310N router. Ubuntu, Windows 7, my Samsung TV and TiVo all connect fine with the 10 character HEX key, but with opensuse 11.4 I can't connect.
I tried to find my solution for hours now but no luck. I'm a medical student and the other day I finally found the time to set up ubuntu for my first time. Everything was working great and I had wireless up and running. However, I tried to set up tethering to my iphone and after that my wireless hasn't been working (I've noticed no other problems). [URL]..Then I used this tutorial [URL].. However, after doing these steps the computer needed to reboot (I actually forget exactly where but I had to reboot in the middle of the second tutorial). After my computer restarted my wireless no longer showed up. By this I mean that wireless network no longer even showed up as an option when I left clicked then connections. However, I did not lose the wireless profile under network connections. So I went to system and noticed that the Broadcom STA driver was no longer active. So I tried to activate again and received this message.
I recently installed 10.10 Maverick on a lenovo S12, and I've been having problems with the wireless connection. First I installed the Broadcom B43 driver. This driver seems to work well except upon resume, I'm no longer connected, and wireless is disabled, and the 'enable wireless' is grayed out and I can't seem to find a way to enable it besides a restart.
I tried what is suggested in this post: [url]
Namely:
Code:
Put:
Code:
This doesn't seem to have any effect
I also tried the Broadcom STA driver. This was only better in that after resuming it tried to reconnect, but never managed to.
I have just upgraded to 10.04 and can't get wireless connectivity because the STA driver for bcm4312 fails to activate. Does this sound familiar to anyone? I had had similar problems in 9.10 and tried to install bcmwl-kernel-source which apparently caused errors in the upgrade process. Not sure if this is part of the problem.
I recently installed Ubuntu x64 on my dell studio 1535 using the windows installer (wubi).
All seems to be working fine apart from the built in wireless card, the proprietary driver (found in hardware drivers) installs and activates successfully and works perfectly. Until I shut down or restart the system. On the next boot the wireless card is 'disabled' and no longer works.
The card I have is a Broadcom Corporation BCM4312 802.11b/g
I am going to try a proper install on a second partition rather than using wubi later on but wondered if this was a commonly occuring problem?
The wireless card works as soon as the driver installs, however I am shown a "restart to activate driver" message and after restarting it's dead.
I'm trying to install version 10.04 of the ubuntu netbook remix on my HP 2133 netbook. I'll try and be as thorough as I can with the information but I'm new to Ubuntu so there's a chance I'm missing something crucial. I'm using Universal USB Installer v.1.60 to make the boot disk. I've checked the MD5 checksums and they're fine. According to the compatibility list it should work straight out the box so I don't know what's going on.
Here's what's happening. I put the USB drive in and boot off it using the BIOS menu. I get a text cursor blinking in the top left corner of my screen for a few seconds and then it just jumps straight back into windows. This is really starting to bug me as I've checked and double checked everything. The only thing I can think of is that it's because my netbook has a VIA C7-M rather than an Intel Atom processor but, as I've mentioned, the compatibility page says it should work. If it is because of this, can I get around it and if so, how?
I'm trying to install fedora 10 onto the HP mini note, I have read how to install from another forum but it does not seem to work. I have setup a USB install using unetbootin. I only get white box lines for a mouse cursor the when it finally begins like it is about to boot into the live installation it freezes and can go no further.
