OpenSUSE Wireless :: Dell Studio 1735 W/BCM4312 WEP Connect Fails?
Jul 31, 2011
Dell Studio 1735 w/BCM4312 WEP fails to connect even though I'm using the 10 character HEX key. It connects fine when there's no security on my Linksys WRT310N router. Ubuntu, Windows 7, my Samsung TV and TiVo all connect fine with the 10 character HEX key, but with opensuse 11.4 I can't connect.
Code:
lspci -nnk tells me I've got:
0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01)
Subsystem: Dell Wireless 1397 WLAN Mini-Card [1028:000c]
Kernel driver in use: wl
[Code]...
View 9 Replies
ADVERTISEMENT
Jul 29, 2011
My Dell Studio 1735 laptop fails to install openSUSE 11.4 install from DVD. The installation tells me it failed to install "kernel.desktop" then grub only has a Floppy entry. When I boot to Recover System /boot has no initrd or kernels.
View 5 Replies
View Related
Jun 10, 2010
I recently installed Ubuntu x64 on my dell studio 1535 using the windows installer (wubi).
All seems to be working fine apart from the built in wireless card, the proprietary driver (found in hardware drivers) installs and activates successfully and works perfectly. Until I shut down or restart the system. On the next boot the wireless card is 'disabled' and no longer works.
The card I have is a Broadcom Corporation BCM4312 802.11b/g
I am going to try a proper install on a second partition rather than using wubi later on but wondered if this was a commonly occuring problem?
The wireless card works as soon as the driver installs, however I am shown a "restart to activate driver" message and after restarting it's dead.
View 5 Replies
View Related
Sep 14, 2010
I have a Dell Inspiron 1545 with a Dell Wireless 1397 WLAN Mini-Card and a Marvell Yukon 88e8040 PCI-E Fast Ethernet Controller, and I cannot for the life of me get the internet to connect. I've tried both wired and wireless connection. I have a PPoE connection through a Verizon FIOS Actiontek router I believe, though the PPoE part may be wrong, I had one five years ago when I first got their internet so they may have changed it. Point is that the ethernet and internet won't work, and without a working ethernet I can't fetch the right drivers for anything.
I had also tried plain ubuntu 10.04 and couldn't get them to work then either. It said 'disconnected' at first, and then said 'device not ready' There is no hardware switch but there is a key toggle. It doesn't seem to matter what state the wireless was in before booting into Ubuntu Studio, so I'm lost as to where to even start. Even though the network manager isn't there like in regular ubuntu, I assume there will be a simple way to connect to the internet once the drivers are found, right?
I've seen issues and read about fixing them, but usually it uses an ethernet connection to fix the wifi connection and, being new to linux (<50 hours worth of experience lifetime), all I managed to do trying to fix it myself was screw up the installation to the point where the laptop couldn't access the home folder and I had to reinstall. Other than that, I am usually very good at following instructions, as long as they apply to my laptop's issue I guess
The only other issue is minor, I can't seem to control the USB mouse I have, but the trackpad works fine so it's no big deal, probably a matter of downloading the mouse driver once the internet works.
Currently I do have internet access via the same laptop while booting Windows 7 (I installed Ubuntu Studio 10.04 on a 10GB Partition with the idea of using an external HD for most data storage).
Oh and it is a 64-bit machine, the Studio version I installed is 32-bit.
View 3 Replies
View Related
Apr 2, 2010
turn wireless card on for the Dell Studio 16 (1645) for SUSE 11.2 64-bit.
View 3 Replies
View Related
Aug 21, 2011
I have a strange problem with my laptop and need your help in resolving it...i am using a Dell Studio XPS 1645..i have got everything working except the wireless.. and the real problem here is that the wlan detects the network but does not connect to it and will keep on looping back and forward doing the same thing again and again..I am using Opensuse 11.4 with Gnome 3 Shell..here is details of the commands that i tried using to fix the issue
# lspci
00:00.0 Host bridge: Intel Corporation Core Processor DMI (rev 11)
00:03.0 PCI bridge: Intel Corporation Core Processor PCI Express Root Port 1 (rev 11)
[code]....
View 8 Replies
View Related
Apr 10, 2010
I just bought a new Dell Studio 1558 and I can't turn the wifi on when logging to my account, the wireless card is installed correctly but the button (F2) doesn't work to turn the wifi on.
[You can see the keyboard shape here]
On windows there is a program from dell that associate these keys (wifi -F2- and Eject optical drive) to their functions.
I wonder how can I achieve this under OpenSuse.
View 3 Replies
View Related
Jan 16, 2011
I posted earlier and got no response, so here i go again. I installed openSUSE 11.3 KDE, it all works fine but the wireless doesnt work and i cant connect to the internet at all, i don't know how to, and i don't even know if the proper drivers are installed. I posted this in the last thread:
"i ran this this command in ubuntu:
Code:
lspci | grep -i network
came up with this result:
Code:
02:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)
I'm not sure if its going to help any but at least you have the name of the wireless card. Please help, Without internet.
View 4 Replies
View Related
Jan 22, 2011
Dell Inspiron 640m laptop, running 10.04. It previously connected via wifi & now fails to connect, although the wireless indicator shows a connection. Connection via ethernet works. Below there's some information that looked like might it be useful to diagnose the problem based on other posts in this forum.
[Code]....
View 2 Replies
View Related
Aug 25, 2010
I need a printer to connect with my Dell studio 15.I choosed this hp printerim not sure whether it works.
View 2 Replies
View Related
Mar 1, 2010
I tried to find my solution for hours now but no luck. I'm a medical student and the other day I finally found the time to set up ubuntu for my first time. Everything was working great and I had wireless up and running. However, I tried to set up tethering to my iphone and after that my wireless hasn't been working (I've noticed no other problems). [URL]..Then I used this tutorial [URL].. However, after doing these steps the computer needed to reboot (I actually forget exactly where but I had to reboot in the middle of the second tutorial). After my computer restarted my wireless no longer showed up. By this I mean that wireless network no longer even showed up as an option when I left clicked then connections. However, I did not lose the wireless profile under network connections. So I went to system and noticed that the Broadcom STA driver was no longer active. So I tried to activate again and received this message.
[Code]...
View 2 Replies
View Related
May 4, 2011
ISSUE SOLVED: FOUND SOLUTION ON LINUX MINT COMMUNITY[URL]... The solution is for debian, but it worked for me on Kubuntu 11.04. I just installed Kubuntu, and my wireless is not getting detected. I tried a variety of solutions I found online, but none worked. It worked perfectly for Ubuntu Gnome.
When I tried installing the Broadcom drivers in the "Additional Drivers", I got an error that the driver could not be installed.
[Code]...
View 3 Replies
View Related
Nov 13, 2010
I have just upgraded to 10.04 and can't get wireless connectivity because the STA driver for bcm4312 fails to activate. Does this sound familiar to anyone? I had had similar problems in 9.10 and tried to install bcmwl-kernel-source which apparently caused errors in the upgrade process. Not sure if this is part of the problem.
View 5 Replies
View Related
Feb 18, 2011
I have loaded the latest version of opensuse and I have everything working but I cannot connect to my wireless WPA2 network. I have downloaded the bcm43xx firmware using the method /usr/sbin/install_bcm43xx_firmware I then restarted the network. The computer will now read the network card and will find networks but I cannot get it to connect at all. At first it would connect using ifup in yast but would disconnect after a few seconds. It would never connect through NM. I have a usb network card that works just fine. I am lost as to how to fix this problem.
View 6 Replies
View Related
Feb 12, 2011
I read the thread about the b43-tools but the git command on there fails.
git clone [URL] Initialized empty Git repository in /sbin/b43-tools/.git/ fatal: [URL] not found: did you run git update-server-info on the server? I am assuming the server is them not me? I have installed the firmware per my dmeg request. And the firmware is installed correctly.
[Code]....
The card works it just will not connect. I think I have that rev 3 issue where I need to edit the SPROM but I can not seem to get the b43-tools installed.
View 9 Replies
View Related
Feb 5, 2011
I am having trouble getting my wireless internet working on Ubuntu 9.10 on a Dell Studio 1535 laptop. My wireless card works just fine in an earlier version (8.10) of Ubuntu. In fact, it worked right out of the box on Intrepid. However, in 9.10, I can not get it to work. I have installed Wicd Network Manager in it, and it shows no networks visible, even though if I reboot and go into my 8.10 version (I have a multiboot), opening Wicd will immediately show several wireless networks within range. So I'm thinking that the 9.10 version is missing a driver for my wireless card, which 8.10 has.
View 1 Replies
View Related
Feb 20, 2010
I have not used Linux in some time (I used to use it back when suse 8 was still out and mandrake linux was still around).
Recently I decided to give it another go and downloaded both the LiveCD and the DVD (both 64-bit versions AND 32-bit versions).
I have a Dell Studio 1747 Laptop (with the 17.3 screen). It has an Intel i7 1.6GB processor, 4GB ram and an ATI Radeon 4650.
My problem is that the LiveCD just will not work. It gets to its boot menu, but when I press enter on the boot KDE live CD option, it will either try to boot and then freeze, or it will boot, you will hear that startup music, but the display will go blank. Could it be that it cannot handle my display or the graphics card on the laptop?
Unfortunately I have Windows 7, which doesn't seem to be supported by the windows installer on the DVD, so I can't test if it would work that way.
I must admit that ubuntu has given me the same grief, and so I wonder if maybe the laptop isn't yet supported properly by linux yet?
how I could use a live system or something, to at least try linux for a few things (I would need to retain windows for games and stuff). I'm not into resizing partitions and things, so I would prefer something else that could work.
View 9 Replies
View Related
Dec 23, 2009
I am using a dell laptop which has Dell 1397 802.11B/G Wireless Mini Card. I not able to connect to internet and was not able to detect what actual problem is weather card is not supported (i.e. drivers are not available) .
Also, if any one can point to exact process to connect to wireless Lan using fedora12.
View 10 Replies
View Related
Oct 13, 2010
I am using OpenSuse 11.2 on a Dell Studio laptop. I have sound through the internal speakers, but no sound through the headphones.I am using KDE and Kmix does have a volume control for the headphone, and it is not muted. None of the sounds are muted.I have run the alsa update as described in another thread and that did not help.
View 9 Replies
View Related
Dec 24, 2009
Since my update to OpenSuse 11.2 knetworkmanager refuses to connect to WEP enabled networks (worked fine with knetworkmanager 11.1). I am sure that I use the correct password and I tried on 3 different networks. The manager is connecting to open networks and WAP protected networks without problems. I saw on other forums that there were similar problems with previous versions of networkmanager. But I could not find a solution for my problem.
View 9 Replies
View Related
Jul 3, 2010
I have tried a lot to get sound from my laptop Dell Studio XPS 16 having i7 CPU.
->uname -a
Linux Pakudidi 2.6.31-rc9-7-default #1 SMP 2009-09-08 18:49:15 +0200 x86_64 x86_64 x86_64 GNU/Linux
->
-> rpm -qa '*alsa*'
alsa-devel-1.0.21-1.1.x86_64
alsa-tools-devel-1.0.21-2.5.x86_64
[Code]....
Here, "enable_msi=1" was not initially included in sound.conf, I added. After adding I find that volume change buttons are working, but sound is not coming. Mixer channels are all set to active mode and vol is MAX to 100. Mixer channels show two tabs -- one showing HDA_Intel and the other showing HDA_ATI_HDMI. Mic Jack mode is Line_in.
View 5 Replies
View Related
Jul 6, 2010
I was trying to install openSUSE 11.2 on Dell XPS Studio, model PP35L, but loading kernel hangs at 94%, I tried F5 for Safe Settings, No APIC, No Local ACPI, Check Installation Media, but it still hangs at 94%. Installation works fine on older computer. Is it because openSuse kernel doesn't recognize the i5 Core processor yet? If this is caused by a driver, is there a way to display the kernel messages and what would be the kernel boot options to disable loading of that driver?
View 2 Replies
View Related
Dec 20, 2009
This is not strictly a Linux question, although I am interested in any Linux cautions as to what to avoid that could impact my Linux on the computer in question. I have Linux (openSUSE-11.1) setup on dual boot with MS-Vista on a Dell Studio 1537 laptop. My wife is "fed up" with Vista, and has asked that I replace Vista with WinXP on this Laptop. I would like to do this over the Christmas holiday break. The laptop's 1 year support warrantee has expired. can someone explain to me the function of the two Dell /dev/sda1 and /dev/sda2 partitions ?
This laptop was purchased with MS Vista installed, with 3 primary partitions (small /dev/sda1 (called "Dell Utility" ),10GB /dev/sda2 (unknown - appears to be some sort of Dell backup/recovery partition ? ), /dev/sda3 (MS Vista which had the remainder of the 250GB drive, although I have subsequently reduced this to 69GB ).
Again, I note /dev/sda3 is the 69GB MS Vista partition (I reduced it to 69GB when I installed Linux (openSUSE-11.1)). I also believe it may be in /dev/sda3 where I should plan on installing winXP. Currently I have openSUSE-11.1 Linux in /dev/sda4 (divided into extended partitions, with /dev/sda5 (swap), /dev/sda6 (root), and /dev/sda7 (/home) for Linux and it works well. I plan to keep openSUSE-11.1 Linux when Vista is replaced by WinXP Can I remove and merge /dev/sda1, /dev/sda2, and /dev/sda3 and replace them with one partition for WinXP ?
Or am I better OFF keeping /sdev/sda1 (Dell Utility) ? and am I better off to keep /dev/sda2 (some sort of Vista ?? recovery) ? and only put winXP on /dev/sda3 ? Aside from the MBR with Grub being destroyed (when I replace Vista with winXP) is there anything else I need to be careful of wrt keeping my openSUSE-11.1 Linux install on this laptop ?
I've also sent a slightly different version of this post as a question to the Dell Support mailing list. p.s. for information, here is some output from Linux commands showing the contents:
[Code]....
View 2 Replies
View Related
Jan 18, 2011
Everything look great but I don't get how to connect to ethernet connection or how to turn on wireless. I always had automatic connection on ubuntu since 8.04. For now I'll look for some repository and download the "nt" applet manager.
View 3 Replies
View Related
Feb 28, 2010
I do have an acer lab top with a BCM4312 wireless card. It is not running under OpenSuSE 11.2 how can I fix it
View 1 Replies
View Related
Aug 12, 2010
Question. How do I enable wlan0 and verify it worksSo far I get.
# /usr/sbin/iwlist scan
wlan0 Interface doesn't support scanning : Network is down
# hwinfo --wlan
[code].....
View 9 Replies
View Related
Sep 12, 2010
I installed OpenSUSE 11.3 with disabled WLAN (otherwise the installation process didn't start). Now the system boots only in Safe Mode with enabled WLAN card (when the WLAN card is disabled it also boots in normal mode though). But even if I try to configure the WLAN card in Safe Mode, the system doesn't boot next time (in Safe Mode) until I add "brokenmodules=ssb" parameter. As I understand after reading this forum I should install a firmware/driver, but there is no install_bcm43xx_firmware script in /usr/sbin directory.
[Code]....
View 3 Replies
View Related
Apr 18, 2011
I have installed b43 with the install script and I can see all wireless networks fine, but NetworkManager just keeps asking me for the WPA passphrase, despite it being correct. I tried disabling WPA on the router, but then the connection hangs at "Configuring interface" instad. I also tried with ifup, but I'm not sure I configured everything correctly. I don't get any smarter from the NetworkManager logs, maybe someone else can decipher them? tail -50 when connection doesn't work:
Code:
Apr 18 17:00:11 jan NetworkManager[1291]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Apr 18 17:00:11 jan NetworkManager[1291]: <info> Config: set interface ap_scan to 1
[Code]...
View 2 Replies
View Related
Feb 3, 2011
I am having a problem while connecting to a D-Link Access Point with Multiple ESSID. It keeps saying activating but in the end nothing. I am using KnetworkManager & there is no Encryption on the Access Point.I am able to get connected with another machine using windows.Here is my hardware info:
0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01)
Subsystem: Dell Wireless 1397 WLAN Mini-Card [1028:000c]
Kernel driver in use: b43-pci-bridge
& the logs:
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.188245] wlan0: authenticate with f0:7d:68:17:e5:a4 (try 1)
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191262] wlan0: authenticated
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191501] wlan0: associate with f0:7d:68:17:e5:a4 (try 1)
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.194008] wlan0: RX AssocResp from f0:7d:68:17:e5:a4 (capab=0x421 status=0 aid=1)
[Code]...
View 7 Replies
View Related
Apr 25, 2011
I have been upgrading (upgrade from 11.3 then fresh install to 11.4) and as usual with Broadcom I have problems. On 11,3 I used the Pacman STA and was working fine. for 11.4, I suppose that my BCM4312 will be supported after installing the b43 driver. It actually woks, few seconds (but never had time to verify) Some background
lspci gives 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Using KDE network manager I can see the wifi AP around, including mine, the problem is when I wan to connect, using WPA2 (TKIP + EAS), I have the right password (I can connect from another station), but when I try here it keeps coming back asking from password .. (I use the kwallet, but that should be out of scope) .. Basically it always fails..
[Code]...
View 7 Replies
View Related
