Ubuntu Networking :: Wireless Does Not Work (Broadcom BCM4312)

Jul 28, 2010

I've just installed Ubuntu on 2 computers, and I'm new to it. However I'm not new to computers. The problem I'm currently running into on one of the computers is that the wireless will not detect any connections, despite there being many. The computer is a HP Compaq v6203AU using the wireless card Broadcom BCM4312 [14e4:4312]. I've went through dozens of walkthroughs, encountering errors in every single one of them, I've spent 8 hours on this one problem and extremely frustrated. It seem to be a problem with the driver that comes as default, and I'm lost at what to do.

The terminal command "lspci -nn | grep 14e4" returns the following:
03:00.0 Network Controller [0280]: Broadcom Corporation BCM4312 802.11a/b/g [14e4:4312]

ifconfig returns the following:
eth0 Link encap:Ethernet HWaddr 00:23:8b:b2:ab:d3
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:20 Base address:0x8000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:96 errors:0 dropped:0 overruns:0 frame:0
TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:7072 (7.0 KB) TX bytes:7072 (7.0 KB)

The computer has no internet access as there is nowhere to connect except through wireless.

View 9 Replies


ADVERTISEMENT

Ubuntu Networking :: 10.04, Wireless Not Working, Broadcom BCM4312?

Sep 16, 2010

I am new to Linux, nevertheless Ubuntu. I have Lucid Lynx on my laptop, with Windows Vista 32 bit along side of it. I have done some research, and found out thathe wireless connector on my laptop, a Broadcom BCM4312, doesn't work with Ubuntu 10.04. I know that I need a driver

View 3 Replies View Related

Ubuntu Networking :: Broadcom BCM4312 Dell Studio - Built In Wireless Card - 'disabled' And No Longer Works

Jun 10, 2010

I recently installed Ubuntu x64 on my dell studio 1535 using the windows installer (wubi).

All seems to be working fine apart from the built in wireless card, the proprietary driver (found in hardware drivers) installs and activates successfully and works perfectly. Until I shut down or restart the system. On the next boot the wireless card is 'disabled' and no longer works.

The card I have is a Broadcom Corporation BCM4312 802.11b/g

I am going to try a proper install on a second partition rather than using wubi later on but wondered if this was a commonly occuring problem?

The wireless card works as soon as the driver installs, however I am shown a "restart to activate driver" message and after restarting it's dead.

View 5 Replies View Related

OpenSUSE Wireless :: Broadcom BCM4312 Working 1 Tries Out Of 10?

Apr 18, 2011

I have installed b43 with the install script and I can see all wireless networks fine, but NetworkManager just keeps asking me for the WPA passphrase, despite it being correct. I tried disabling WPA on the router, but then the connection hangs at "Configuring interface" instad. I also tried with ifup, but I'm not sure I configured everything correctly. I don't get any smarter from the NetworkManager logs, maybe someone else can decipher them? tail -50 when connection doesn't work:

Code:
Apr 18 17:00:11 jan NetworkManager[1291]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Apr 18 17:00:11 jan NetworkManager[1291]: <info> Config: set interface ap_scan to 1

[Code]...

View 2 Replies View Related

General :: What Distro Of Linux Will Work With Broadcom BCM4312

Sep 25, 2010

I am trying to start using linux, and am new, so sorry if this is dumb. I started out trying Ubuntu, but that didn't work. After that I had tried Mint, and had several problems besides the Network Connector. Now I'm trying Fedora, but if that doesn't work is there a different Linux distro that will work?

View 6 Replies View Related

OpenSUSE Wireless :: Broadcom BCM4312 WiFi When Using DHCP?

Feb 3, 2011

I am having a problem while connecting to a D-Link Access Point with Multiple ESSID. It keeps saying activating but in the end nothing. I am using KnetworkManager & there is no Encryption on the Access Point.I am able to get connected with another machine using windows.Here is my hardware info:

0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01)
Subsystem: Dell Wireless 1397 WLAN Mini-Card [1028:000c]
Kernel driver in use: b43-pci-bridge
& the logs:
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.188245] wlan0: authenticate with f0:7d:68:17:e5:a4 (try 1)
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191262] wlan0: authenticated
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191501] wlan0: associate with f0:7d:68:17:e5:a4 (try 1)
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.194008] wlan0: RX AssocResp from f0:7d:68:17:e5:a4 (capab=0x421 status=0 aid=1)

[Code]...

View 7 Replies View Related

OpenSUSE Wireless :: Broadcom With 11.4 (BCM4312) Get Deauthenticating (reason = 3)?

Apr 25, 2011

I have been upgrading (upgrade from 11.3 then fresh install to 11.4) and as usual with Broadcom I have problems. On 11,3 I used the Pacman STA and was working fine. for 11.4, I suppose that my BCM4312 will be supported after installing the b43 driver. It actually woks, few seconds (but never had time to verify) Some background

lspci gives 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Using KDE network manager I can see the wifi AP around, including mine, the problem is when I wan to connect, using WPA2 (TKIP + EAS), I have the right password (I can connect from another station), but when I try here it keeps coming back asking from password .. (I use the kwallet, but that should be out of scope) .. Basically it always fails..

[Code]...

View 7 Replies View Related

OpenSUSE Wireless :: Broadcom-wl BCM4312 9 Firmware Missing ?

Aug 11, 2011

By following the rules to post a new issue for my broadcom 4312 her it is:

Code:

Code:

Code:

Code:

Code:

Code:

View 9 Replies View Related

Slackware :: Broadcom Wireless BCM4312 Immediately Disconnects On 13.37?

May 5, 2011

I have a problem with the built-in wireless-card of my laptop. I can connect to the wireless DSL-router using wicd (wicd-1.7.0-486-2 from /extra), wicd reports that it connects and obtains an IP-address. It then changes the status to connected. Immediately after that (may be a second later) the status changes back to disconnected and I can't reach the network.

Here some specs: Kernel: self-compiled 2.6.37-6-generic, the only option I changed from the standard generic config was to enable PAE, but I also tried it with the standard generic kernel and the huge kernel. Wireless card: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Firmware installed with the packages from Slackbuilds.org: network/b43-fwcutter network/b43-firmware. The wireless card is working correctly under Debian, so I think this is not a hardware issue.

View 7 Replies View Related

Fedora Hardware :: Broadcom Wireless BCM4312 On Linux Kernel 2.6.35.10-72

Dec 26, 2010

I have a problem here with my updated kernel. I'm currently using Fedora 14 kernel 2.6.35.9-64, and my wireless card Broadcom BCM4312, which had an issue before with Linux distros, is working fine already, thanks to the kmod-wl software driver. My problem now is this, after updating to kernel 2.6.35.10-72, fedora does not boot, and I noticed that the wireless card is the only thing not activating, compared to the working kernel. And when i looked at the log of the bootup (pressed right arrow key), I saw this:

[code]...

View 3 Replies View Related

OpenSUSE Wireless :: 'Broadcom Corporation BCM4312 802.11' Can't Connect To The Internet?

Jan 16, 2011

I posted earlier and got no response, so here i go again. I installed openSUSE 11.3 KDE, it all works fine but the wireless doesnt work and i cant connect to the internet at all, i don't know how to, and i don't even know if the proper drivers are installed. I posted this in the last thread:

"i ran this this command in ubuntu:

Code:
lspci | grep -i network
came up with this result:

Code:
02:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)

I'm not sure if its going to help any but at least you have the name of the wireless card. Please help, Without internet.

View 4 Replies View Related

CentOS 5 Hardware :: Lenovo S12 Wireless - Broadcom Bcm4312 Rev01 - Using NdisWrapper

Oct 17, 2010

This is probably trivial for most linux users, but here is what I did to get wireless working with the Centos 5.5 LiveCD on my Lenovo S12.

For reference, here is the output of the lspci command:

View 3 Replies View Related

Ubuntu Networking :: HP Pavilion DV6 With Broadcom BCM4312

Sep 4, 2010

I'm relatively new to Ubuntu and Linux OS in general, hope this hasn't already been solved but after trying for 24hrs+ I think it may be time for me to start my own thread (sorry if there is already one). I have been desperately trying to get my Broadcom BCM4312 wireless card to work and after searching about 100 sites and threads I still can't get it going Here are some of the problems Ive been having(I am running Ubuntu 8.04 by the way):

1. Tried installing "Broadcom STA Wireless Driver" under System->Administration->hardware drivers but after install it didn't show any signs of working.

2. I tried getting the Linux driver off the website [URL]... and followed the instructions in the readme to the letter, yet when i am asked to type in one of the final commands: # sudo insmod wl.ko

I get the output: # error inserting 'wl.ko': -1 File exists I have also looked at this website where a guy posts the same problem but no one posted anything back: [URL]...

View 9 Replies View Related

Ubuntu Networking :: Broadcom BCM4312 Does Not Turn On?

Jun 11, 2011

Last night I turned off my Wireless Card Broadcom BCM4312 via button. Today I can't turn it on... any help?

More Info: System: Ubuntu 11.04 (same thing happened in 10.11 so I upgraded and it fixed itself) Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)

View 9 Replies View Related

Ubuntu Networking :: Broadcom BCM4312, Desperation Setting In?

Jan 11, 2011

I'm flummoxed, guilt-stricken and near my wit's end. The Ubuntu-preloaded Inspiron 1545 I persuaded my girfriend to buy contains the dreaded BCM4312, and nothing I can think of seems to be helping. I've tried various approaches with the STA and B43 drivers. Gad, I feel like I've tried EVERYTHING. Here's where her poor machine's at right now:

Code:
uname -r
2.6.35-24-generic
lspci -v -- omitting output from all the unrelated devices
0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)
Subsystem: Dell Wireless 1397 WLAN Mini-Card
Flags: bus master, fast devsel, latency 0, IRQ 17

[Code]...

View 6 Replies View Related

Ubuntu Networking :: Broadcom BCM4312 - 4315 - Activated But No Signal

Jun 16, 2010

I recently bought a Lenovo laptop which comes with a wireless card called Broadcom BCM4312 but in dmesg it says "bcm4315 hybrid wireless controller".

Jockey says the driver is installed, activated and in use. However I don't get any signal (I even moved the laptop to the same room the wireless router is).

I run iwevent and nothing appeared.

I run Kubuntu 10.04, fresh install from a USB stick, latest updates. I replaced knetworkmanager with the network-manager-gnome. network-manager-gnome works fine and I can connect to wired connection with no problem.

Network-manager-gnome says that the wireless is disconnected. What can be done to make the wireless work?

View 4 Replies View Related

Ubuntu Networking :: Network Disabled On Acer Aspire With BCM4312 802.11 B/g (Broadcom)

Aug 7, 2010

I'm running Kubuntu and Windows on the same machine but when I swap over to Kubuntu I can't get the wireless to work. The lshw command returns network disabled but the machine can see that there is a wlan0 connection.

I've been trying to install the broadcom Linux driver from their site but the instructions fall apart at step 3: cd bnx...version/ ( directory just created by tar). I'm guessing this is because I don't have a Live CD (after almost a week of trying to burn a disc I just broke down and got Wubi) but that doesn't change the fact I have no idea what to do now or if this will even work.

If it makes any difference, the wired connection will also occasionally die mysteriously after about 30-60 minutes of use and refuse to re-activate but work fine when I switch over to Windows or just plug it into the router.

View 3 Replies View Related

Ubuntu Networking :: Broadcom Wireless Doesn't Work

May 20, 2010

I'm working on Lucid, in HP Pavilion 9730us laptop.

My wireless broadcom card was working just fine until now as i installed it with the Hardware Devices manager, Today i put a new ALFA AWUS036H usb card to work with aircrack. both cards were working together for a while, but as i started playing around with aircrack the broadcom card of the HP has stopped working.

I made a mistake and followed the aircrack tutorial for R8187 / ieee80211 stacks driver, while i'm using RTL 8187 / mac80211 stack drivers, and blacklisted the RTL8187 , rebooted and then both card didn't work. I un-blacklisted it, and the ALFA is working but the broadcom not!

iwconfig shows me only one wireless card on wlan0 the blue light showing activity in the HP card doesn't go on.

Tried to uninstall and reinstall broadcom drivers, still no change.

View 2 Replies View Related

Ubuntu Networking :: Broadcom Corporation BCM4312 / Latest Ubuntu Version / HP 67352 Notebook?

Jul 30, 2010

My wireless isnt working on my HP 6735s Notebook.Theres no drivers in the driver manager nor does it find my network.The wireless indicator on my laptop also shows my wireless is turned off even when i press the button to turn it on.

lspci:

michael@ubuntu:~$ lspci
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge
00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx)
00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0)
00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3)
00:09.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 4)
code....

View 3 Replies View Related

Fedora Networking :: Wireless Network Doesn't Work After Kernel Update (Broadcom) / Sort It?

Aug 23, 2009

I wireless network card is Broadcom Corporation BCM431, but is doesn't work after I update kernel from
2.6.29.6-217.2.7 to 2.6.29.6-217.2.8.

Linux localhost.localdomain 2.6.29.6-217.2.7.fc11.x86_64 #1 SMP Fri Aug 14 20:53:08 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux

View 2 Replies View Related

General :: Actually Installing A .tar.gz. Broadcom BCM4312

Sep 20, 2010

I need a driver to work with my Broadcom BCM4312 Network Connector on my Dell Inspiron 1525 Laptop. I have already extracted the tarball, but I don't know what to do to actually install the driver. I am running Ubuntu 10.04.1 LTS, with Windows dual booting.

View 14 Replies View Related

General :: Broadcom BCM4312 Firmware In Ubuntu 10.10 Beta?

Sep 26, 2010

I recently switched from 10.04.1 Ubuntu that I had for only about a week, to Ubuntu 10.10 Beta. I switched because I heard that 10.10 comes with firmware right out of the box for BCM4312. I am new with Linux, and Ubuntu, but I do know what some of the commands do and etc. I got 10.10 installed, but the wireless options say "Not connected|Firmware Missing" What do I need to activate the firmware, or install it?

View 3 Replies View Related

Fedora :: Network Controller Is A Broadcom BCM4312?

Jul 12, 2011

I'm fairly new to fedora, and I installed it on my gateway kav60 netbook. Everything works fine, except that the wifi is saying that the firmware is missing. Is there a way to fix this?

View 1 Replies View Related

Hardware :: Lucid - Problems With Broadcom BCM4312?

Aug 6, 2010

I'm having problems using my wireless device on ubuntu lucid.

Here's the output of dmesg;

Code:
[ 2884.620307] b43 ssb0:0: firmware: requesting b43/ucode15.fw
[ 2884.648540] b43 ssb0:0: firmware: requesting b43/lp0initvals15.fw
[ 2884.654745] b43 ssb0:0: firmware: requesting b43/lp0bsinitvals15.fw
[ 2884.796399] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[ 2890.345264] ADDRCONF(NETDEV_UP): wlan0: link is not ready

[Code]...

View 2 Replies View Related

Ubuntu Networking :: Uninstall BCM4312 Wireless Driver?

Jul 10, 2010

I want to know how to uninstall the bcm4312 wireless driver from my ubuntu 10,04.

View 1 Replies View Related

Ubuntu Networking :: Installing Downloaded Wireless Driver BCM4312

Aug 24, 2011

I just installed Ubuntu 11.04 on my Dell Mini 10v and for some reason I just realized that my wired network connection is not working for some reason. And not in windows either. But my wireless works in windows. So I have downloaded the latest Broadcom STA wireless drivers for linux and have tried to follow this tutorial to install it. But when I get to:

make -C /lib/modules/<2.6.xx.xx>/build M=`pwd` clean I can't get it to work. It says:

make: Entering directory '/usr/src/linux-header-2.6.38-8-generic'
scripts/Makefile.build:44: /usr/src/linux-header-2.6.38-8-generic/pwd/Makefile: No such file or directory
make[1]: *** No rule to make target '/usr/src/linux-header-2.6.38-8-generic

[Code]....

View 9 Replies View Related

Fedora Networking :: BCM4312 Does Not Work In F12 - WiFi Not Detected

Oct 24, 2010

I am using fedora 12 with bcm4312 wireless card. But wifi is not detected by os. I am new to open source .

View 4 Replies View Related

Fedora Networking :: Cannot Get BCM4312 Wireless Card Working

Apr 9, 2010

I recently purchased an Acer eMachines E525 laptop, and currently have it dual booting Windows 7 and Fedora 12 x86_64 with the 2.6.31.5-127 kernel. I've been completely unable to get the wireless card working in Fedora (it works fine in windows).

lspci lists the following about the wireless card:
Code:
Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
so I assume it's a BCM4312.

So far I have tried downloading the driver from [URL] and then trying to install it according to the accompanying readme file: [URL]. However, when I try to make the driver, I get the following message:

Code:
KBUILD_NOPEDANTIC=1 make -C /lib/modules/`uname -r`/build M=`pwd`
make: *** /lib/modules/2.6.32.10-90.fc12.x86_64/build: No such file or directory. Stop.
The Readme says that if I get this kind of error, I need to install the "kernel-devel" package, but I have this installed and it still returns the same error.

I have also tried following the fw-cutter instructions for fedora from [URL], but it still doesn't work. I realise there's the option of using ndiswrapper, but I gave that a shot with Fedora 11 on the same machine and had no luck, and I'd really like to see whether any of the other options work before going down that route.

View 6 Replies View Related

Ubuntu Networking :: BCM4312 802.11b/g 9.10 Dell Inspiron 11 Wireless Driver Now Missing?

Mar 1, 2010

I tried to find my solution for hours now but no luck. I'm a medical student and the other day I finally found the time to set up ubuntu for my first time. Everything was working great and I had wireless up and running. However, I tried to set up tethering to my iphone and after that my wireless hasn't been working (I've noticed no other problems). [URL]..Then I used this tutorial [URL].. However, after doing these steps the computer needed to reboot (I actually forget exactly where but I had to reboot in the middle of the second tutorial). After my computer restarted my wireless no longer showed up. By this I mean that wireless network no longer even showed up as an option when I left clicked then connections. However, I did not lose the wireless profile under network connections. So I went to system and noticed that the Broadcom STA driver was no longer active. So I tried to activate again and received this message.

[Code]...

View 2 Replies View Related

Ubuntu Networking :: Enable Wireless Grayed Out After Resume From Suspect With BCM4312

Nov 2, 2010

I recently installed 10.10 Maverick on a lenovo S12, and I've been having problems with the wireless connection. First I installed the Broadcom B43 driver. This driver seems to work well except upon resume, I'm no longer connected, and wireless is disabled, and the 'enable wireless' is grayed out and I can't seem to find a way to enable it besides a restart.

I tried what is suggested in this post: [url]

Namely:

Code:

Put:


Code:

This doesn't seem to have any effect

I also tried the Broadcom STA driver. This was only better in that after resuming it tried to reconnect, but never managed to.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved