OpenSUSE Wireless :: Broadcom BCM4312 Working 1 Tries Out Of 10?
Apr 18, 2011
I have installed b43 with the install script and I can see all wireless networks fine, but NetworkManager just keeps asking me for the WPA passphrase, despite it being correct. I tried disabling WPA on the router, but then the connection hangs at "Configuring interface" instad. I also tried with ifup, but I'm not sure I configured everything correctly. I don't get any smarter from the NetworkManager logs, maybe someone else can decipher them? tail -50 when connection doesn't work:
Apr 18 17:00:11 jan NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
Apr 18 17:00:11 jan NetworkManager: <info> Config: set interface ap_scan to 1
I am new to Linux, nevertheless Ubuntu. I have Lucid Lynx on my laptop, with Windows Vista 32 bit along side of it. I have done some research, and found out thathe wireless connector on my laptop, a Broadcom BCM4312, doesn't work with Ubuntu 10.04. I know that I need a driver
I am having a problem while connecting to a D-Link Access Point with Multiple ESSID. It keeps saying activating but in the end nothing. I am using KnetworkManager & there is no Encryption on the Access Point.I am able to get connected with another machine using windows.Here is my hardware info:
0c:00.0 Network controller : Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card [1028:000c] Kernel driver in use: b43-pci-bridge & the logs: Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.188245] wlan0: authenticate with f0:7d:68:17:e5:a4 (try 1) Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191262] wlan0: authenticated Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191501] wlan0: associate with f0:7d:68:17:e5:a4 (try 1) Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.194008] wlan0: RX AssocResp from f0:7d:68:17:e5:a4 (capab=0x421 status=0 aid=1)
I have been upgrading (upgrade from 11.3 then fresh install to 11.4) and as usual with Broadcom I have problems. On 11,3 I used the Pacman STA and was working fine. for 11.4, I suppose that my BCM4312 will be supported after installing the b43 driver. It actually woks, few seconds (but never had time to verify) Some background
lspci gives 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Using KDE network manager I can see the wifi AP around, including mine, the problem is when I wan to connect, using WPA2 (TKIP + EAS), I have the right password (I can connect from another station), but when I try here it keeps coming back asking from password .. (I use the kwallet, but that should be out of scope) .. Basically it always fails..
I posted earlier and got no response, so here i go again. I installed openSUSE 11.3 KDE, it all works fine but the wireless doesnt work and i cant connect to the internet at all, i don't know how to, and i don't even know if the proper drivers are installed. I posted this in the last thread:
"i ran this this command in ubuntu:
Code: lspci | grep -i network came up with this result:
I have a problem with the built-in wireless-card of my laptop. I can connect to the wireless DSL-router using wicd (wicd-1.7.0-486-2 from /extra), wicd reports that it connects and obtains an IP-address. It then changes the status to connected. Immediately after that (may be a second later) the status changes back to disconnected and I can't reach the network.
Here some specs: Kernel: self-compiled 2.6.37-6-generic, the only option I changed from the standard generic config was to enable PAE, but I also tried it with the standard generic kernel and the huge kernel. Wireless card: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Firmware installed with the packages from Slackbuilds.org: network/b43-fwcutter network/b43-firmware. The wireless card is working correctly under Debian, so I think this is not a hardware issue.
I've just installed Ubuntu on 2 computers, and I'm new to it. However I'm not new to computers. The problem I'm currently running into on one of the computers is that the wireless will not detect any connections, despite there being many. The computer is a HP Compaq v6203AU using the wireless card Broadcom BCM4312 [14e4:4312]. I've went through dozens of walkthroughs, encountering errors in every single one of them, I've spent 8 hours on this one problem and extremely frustrated. It seem to be a problem with the driver that comes as default, and I'm lost at what to do.
The terminal command "lspci -nn | grep 14e4" returns the following: 03:00.0 Network Controller : Broadcom Corporation BCM4312 802.11a/b/g [14e4:4312]
ifconfig returns the following: eth0 Link encap:Ethernet HWaddr 00:23:8b:b2:ab:d3 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0x8000
I have a problem here with my updated kernel. I'm currently using Fedora 14 kernel 18.104.22.168-64, and my wireless card Broadcom BCM4312, which had an issue before with Linux distros, is working fine already, thanks to the kmod-wl software driver. My problem now is this, after updating to kernel 22.214.171.124-72, fedora does not boot, and I noticed that the wireless card is the only thing not activating, compared to the working kernel. And when i looked at the log of the bootup (pressed right arrow key), I saw this:
I recently installed Ubuntu x64 on my dell studio 1535 using the windows installer (wubi).
All seems to be working fine apart from the built in wireless card, the proprietary driver (found in hardware drivers) installs and activates successfully and works perfectly. Until I shut down or restart the system. On the next boot the wireless card is 'disabled' and no longer works.
The card I have is a Broadcom Corporation BCM4312 802.11b/g
I am going to try a proper install on a second partition rather than using wubi later on but wondered if this was a commonly occuring problem?
The wireless card works as soon as the driver installs, however I am shown a "restart to activate driver" message and after restarting it's dead.
after finally installing 11.3, I found that my wireless NIC had stopped working. I've spent about 4 hours trying various online tutorials to get the card working, but I'm still right where I was when I began. The card as reported by lspci:
I recently purchased an Acer eMachines E525 laptop, and currently have it dual booting Windows 7 and Fedora 12 x86_64 with the 126.96.36.199-127 kernel. I've been completely unable to get the wireless card working in Fedora (it works fine in windows).
lspci lists the following about the wireless card: Code: Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) so I assume it's a BCM4312.
So far I have tried downloading the driver from [URL] and then trying to install it according to the accompanying readme file: [URL]. However, when I try to make the driver, I get the following message:
Code: KBUILD_NOPEDANTIC=1 make -C /lib/modules/`uname -r`/build M=`pwd` make: *** /lib/modules/188.8.131.52-90.fc12.x86_64/build: No such file or directory. Stop. The Readme says that if I get this kind of error, I need to install the "kernel-devel" package, but I have this installed and it still returns the same error.
I have also tried following the fw-cutter instructions for fedora from [URL], but it still doesn't work. I realise there's the option of using ndiswrapper, but I gave that a shot with Fedora 11 on the same machine and had no luck, and I'd really like to see whether any of the other options work before going down that route.
I have a Dell Vostro 1500 that has a Broadcom BCM4312 wireless card installed. I do not have access to a wired connection to the web so any thing I have to install is a download on my windows machine and then transfer that to the debian machine. I just finished installing Debian Squeeze but can not get my wireless card to scan for any networks. I found a tutorial at [URL] and followed the steps there. Finding all the dependances and installing them one by one (took me all day). My wireless card still will not scan for networks. After doing a 'sudo ifconfig eth1 up' it still will not scan for networks.
Output from ifconfig: raygo75@RayGo-2:~$ sudo ifconfig eth1 Link encap:Ethernet HWaddr 00:16:44:9b:e9:cc inet6 addr: fe80::216:44ff:fe9b:e9cc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 Base address:0xc000
How do I get around this? It wants to get something from [URL] and I do not have internet access. It looks to me like it just wants to download the wl dirver, again, which I have done in the previous instructions I found. I am a retired UNIX (hp-unix) administrator so I know my way around the system.
I need a driver to work with my Broadcom BCM4312 Network Connector on my Dell Inspiron 1525 Laptop. I have already extracted the tarball, but I don't know what to do to actually install the driver. I am running Ubuntu 10.04.1 LTS, with Windows dual booting.
I'm relatively new to Ubuntu and Linux OS in general, hope this hasn't already been solved but after trying for 24hrs+ I think it may be time for me to start my own thread (sorry if there is already one). I have been desperately trying to get my Broadcom BCM4312 wireless card to work and after searching about 100 sites and threads I still can't get it going Here are some of the problems Ive been having(I am running Ubuntu 8.04 by the way):
1. Tried installing "Broadcom STA Wireless Driver" under System->Administration->hardware drivers but after install it didn't show any signs of working.
2. I tried getting the Linux driver off the website [URL]... and followed the instructions in the readme to the letter, yet when i am asked to type in one of the final commands: # sudo insmod wl.ko
I get the output: # error inserting 'wl.ko': -1 File exists I have also looked at this website where a guy posts the same problem but no one posted anything back: [URL]...
I installed OpenSUSE 11.3 with disabled WLAN (otherwise the installation process didn't start). Now the system boots only in Safe Mode with enabled WLAN card (when the WLAN card is disabled it also boots in normal mode though). But even if I try to configure the WLAN card in Safe Mode, the system doesn't boot next time (in Safe Mode) until I add "brokenmodules=ssb" parameter. As I understand after reading this forum I should install a firmware/driver, but there is no install_bcm43xx_firmware script in /usr/sbin directory.
I am trying to start using linux, and am new, so sorry if this is dumb. I started out trying Ubuntu, but that didn't work. After that I had tried Mint, and had several problems besides the Network Connector. Now I'm trying Fedora, but if that doesn't work is there a different Linux distro that will work?
I'm flummoxed, guilt-stricken and near my wit's end. The Ubuntu-preloaded Inspiron 1545 I persuaded my girfriend to buy contains the dreaded BCM4312, and nothing I can think of seems to be helping. I've tried various approaches with the STA and B43 drivers. Gad, I feel like I've tried EVERYTHING. Here's where her poor machine's at right now:
Code: uname -r 2.6.35-24-generic lspci -v -- omitting output from all the unrelated devices 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card Flags: bus master, fast devsel, latency 0, IRQ 17
I recently switched from 10.04.1 Ubuntu that I had for only about a week, to Ubuntu 10.10 Beta. I switched because I heard that 10.10 comes with firmware right out of the box for BCM4312. I am new with Linux, and Ubuntu, but I do know what some of the commands do and etc. I got 10.10 installed, but the wireless options say "Not connected|Firmware Missing" What do I need to activate the firmware, or install it?
I recently bought a Lenovo laptop which comes with a wireless card called Broadcom BCM4312 but in dmesg it says "bcm4315 hybrid wireless controller".
Jockey says the driver is installed, activated and in use. However I don't get any signal (I even moved the laptop to the same room the wireless router is).
I run iwevent and nothing appeared.
I run Kubuntu 10.04, fresh install from a USB stick, latest updates. I replaced knetworkmanager with the network-manager-gnome. network-manager-gnome works fine and I can connect to wired connection with no problem.
Network-manager-gnome says that the wireless is disconnected. What can be done to make the wireless work?
I'm running Kubuntu and Windows on the same machine but when I swap over to Kubuntu I can't get the wireless to work. The lshw command returns network disabled but the machine can see that there is a wlan0 connection.
I've been trying to install the broadcom Linux driver from their site but the instructions fall apart at step 3: cd bnx...version/ ( directory just created by tar). I'm guessing this is because I don't have a Live CD (after almost a week of trying to burn a disc I just broke down and got Wubi) but that doesn't change the fact I have no idea what to do now or if this will even work.
If it makes any difference, the wired connection will also occasionally die mysteriously after about 30-60 minutes of use and refuse to re-activate but work fine when I switch over to Windows or just plug it into the router.
I have a problem with my wireless connection. I just installed the broadcom BCM4312 firmware in order to recognize my hardware. Everything is ok, it connects to my wireless network, but i can't access the internet. My wireless is in eth1 interface. If i try to connect using PPPOE it works.
Dell Studio 1735 w/BCM4312 WEP fails to connect even though I'm using the 10 character HEX key. It connects fine when there's no security on my Linksys WRT310N router. Ubuntu, Windows 7, my Samsung TV and TiVo all connect fine with the 10 character HEX key, but with opensuse 11.4 I can't connect.
Yet another Linux newbie with wireless problems I'm afraid. I saw some postings that appear very similar but I don't have any Linux experience and don'h to make uncontrolled changes to the environment without expert advice.Background: I have an old laptop (HP Pavilion dv9000) with Vista installed and a troubled history (overheating motherboard failure), so I put it on the shelf and replaced it with a new Windows 7 laptop (Dell Studio 1555). But I have been intrigued by the Ubuntu reviews and thought I would dig out the old laptop and install Kubuntu 11.04 (replacing the 2 Vista partitions with a single Kubuntu partition).
Kubuntu installation was easy and I am impressed by the Kubuntu interface, but I soon noticed that it was not detecting my wireless router, which works fine for everything else (Dell, Sony Bravia TV and also an internet radio). The wired connection is okay (using it now) so I guessed the problem was Kubuntu notognising the Broadcom BCM4311.The network interface tool shows the wired connection but the Wireless tab is greyed out.I also installed Wicd Network Manager but that just confirmed what I knew.I noticed other threads have asked for the lspci and lsusb details so here they are:
I just installed latest stable Debian (KDE) on my laptop, Dell Vostro 3400, which uses Broadcom 4313 (I think) wireless controller. I did install the proprietary driver package from Debian called breadcom-sta-common<version no>.deb. I remember it's the same driver I used for my previous Ubuntu installation. I also installed the KDE Network ManagerFront-End and the wireless tab on the manager is disabled (greyed out). I finally tried the steps from Debian Wiki Wireless section and at the end, when I run "modprobe wl", it says "FATAL: Module wl not found". Is there some more steps I need to do?
I have a HP Mini 5105 SSD netbook, runing Ubuntu 10.10 with 2Gb RAM. My wireless card is a Broadcom BCM43224 802.11a/b/g/n. Its driver is enabled and running. The wired network connection runs fine too. The problem: Wireless stopped working. When I right click on the network icon, the enable network option is clicked, but the "enable wireless" option is listed in dark grey and cannot be clicked on. I have recently updated my kernel version to 2.6.35-24-generic. What I have already tried: this one too I got to know there seems to be a problem with the 2.6.35-24-generic kernel. I have gone into the GRUB menu (it took some time to find out that you have to keep the Shift key pressed during startup for the GRUB menu to show), chosen the older kernel version (2.6.35-23-generic) and then removed the faulty one. Nevertheless, nothing has changed. I still cannot enable the wireless. The outcome to lshw -C network is:
My wireless works perfectly with my university networks. But I have problem connecting to my house router. The first time I installed Ubuntu 10.10, it connected to internet and worked well. After a restart needed by nVidia driver, my house wireless stopped working while my university wireless still works. I have tried reinstalling the driver using System/Administration/Additional Drivers and manually
Recently I moved from Intrepid Ibex to Lucid Lynx and everything went fine during and post installation except wireless B4311. I tried to install the specific driver from System-> Administration-> Hardware Drivers but it comes out with an error logged in file jockey.log
I have this problem with my wifi for 2 weeks now.It used to work great and after some updates the Network Manager keeps rejecting my wpa passwords. The wifi card is working (tested with other OS's) and the wifi light on my HP laptop is on. I have installed broadcom drivers.The problem is similar with this one here but changing from default kernel to desktop didn't work in my case. have already read through Getting your Wireless to work and Broadcom instructions
I'm happily using OpenSuse 11.2/KDE on my laptop equipped with a Broadcom BCM4311 WLAN chip, but today, after a restart, WLAN ceased to work. I mean that Network Connection doesn't show anymore available WLANs. Two things that seem strange to me are that the