I just loaded Fedora 10 onto my laptop and now I'm trying to add a USB wireless adapter with little to no luck (well no luck at ALL.)
# lsmod
Module Size Used by
nls_utf8 5632 0
fuse 49436 2
bridge 43796 0
[Code].....
However I am having some issues with drivers. I need to install a Patriot Wireless N USB wireless adapter in Crunchbang but when I follow the directions for installing the drivers and am using the command "make" I get an error that says '*** /lib/modules/2.6.32-5-amd64/build: No such file or directory. Stop . *** [modules] Error 2"
View 1 Replies View Relatedhow to use my alpha awus036nh wireless adapter in bt3 that i am running from cd, whenever i try to scan for aps the built in adapter kicks in.
View 1 Replies View RelatedI just acquired a Wi-Fire long-range wi-fi adapter, and I would like to test it with my Ubuntu desktop computer. However, my machine defaults to using an internal, discrete wireless card (not hard-wired into the motherboard.) How can I set my new wireless adapter as the default wireless connection? How can I disable my internal wireless card (without opening my computer case)?
View 1 Replies View RelatedI am new to linux and backtrack 4 and I didn't have a hard time installing it but my question is that I cant see my wireless adapter at all even in vmware settings. I am using Vmware player, backtrack 4, Gateway netbook LT2030u and my wireless adapter is Atheros AR5B95.
View 6 Replies View RelatedI have just taken the plunge and began learning linux. I currently have a compaq laptop which ive partioned to run windows/linux.I have Debian 7.9 installed, and have been able to surf online no problem with my ethernet, but have ran into big problem attempting to get the wifi to operate.
I checked online first to make sure the adapter i bought was compatible, which it is.So far i have done the following.
sudo aptitude install wireless-tools
sudo apt-get update && apt-get install firmware-iwlwifi
Ran lsusb..
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 005: ID 2357:0101
Bus 001 Device 003: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 001 Device 004: ID 05c8:036e Cheng Uei Precision Industry Co., Ltd (Foxlink)
After checking online, it appears Bus 001 Device 005: ID 2357:0101 is the USB adapter.I then ran lspci
00:00.0 Host bridge: Intel Corporation ValleyView SSA-CUnit (rev 0a)
00:02.0 VGA compatible controller: Intel Corporation ValleyView Gen7 (rev 0a)
00:13.0 SATA controller: Intel Corporation ValleyView 6-Port SATA AHCI Controller (rev 0a)
[code]....
I then got instructions to do the following, but after entering the first line, nothing happened, the cursor just flashed at beginning of next line.
# sudo cp -R . /usr/src/rtl8812AU_8821AU_linux-1.0
# sudo dkms add -m rtl8812AU_8821AU_linux -v 1.0
# sudo dkms build -m rtl8812AU_8821AU_linux -v 1.0
# sudo dkms install -m rtl8812AU_8821AU_linux -v 1.0
Buffalo's NfinitiTM Wireless-N Ultra-Compact USB 2.0 Adapter!!Do any of you having this working in Linux?
View 1 Replies View RelatedDell D630 not seeing the wireless adapter
View 1 Replies View RelatedI have been all over the internet trying to find a wireless adapter that will work with my older Toshiba notebook. I have several but none seem to be recognized. I am willing to purchase one and I would like it to work out of the box.
View 12 Replies View RelatedI have Ubuntu 10.4 and I have a skylink usb wireless adapter. It came with the driver on a disc but I don't know how to install it. I looked at the README file but I don't understand what to do.
View 14 Replies View RelatedHow to install wireless USB Adapter WUA-0603 ?
I have Ubuntu 10.04 LTS
I have a Belkin Wireless G USB Network Adapter but I cant get on the internet with it.The laptop is running Damn Small Linux.Heres what is going on and the code I typed:
ndiswrapper -i rt73.INF
ndiswrapper -l
modprobe ndiswrapper
iwconfig
ndiswrapper says the driver and hardware are present but iwconfig and ifconfig don't say anything.The wireless adapter works fine in windows 2000 and windows xp with the same driver.The green LED on the wireless adapter never flashes like it is supposed to.
time Windows user here; limited line command experience from early computer learning; Just wiped my drive and installed Ubuntu. How do I install a driver for the netgear wireless adapter - it was already installed in the machine. I've downloaded the driver believed to work. What next? Also, any instruction on educating myself on Linux/Ubuntu basics?
View 14 Replies View RelatedMy wireless adapter keeps getting booted from the internet. I heard I might need Ndswrapper. Does anybody know how to use Ndswrapper?
View 2 Replies View RelatedI am brand new to Linux and Ubuntu. However it was very easy and smooth to install and get updated using my wired ethernet connection. I am now trying to understand how to have my wireless network adapter recognized or driver installed. I will be searching around the forums but it suggested I make an initial post as a new user. I am using an older Dell Inspiron 2200. I believe the chipset in my wireless adapter is indeed Broadcomm, so hopefully that will help direct any responses.
View 2 Replies View RelatedLooking for driver for Linksys Wireless Notebook adapter WPC55AG
View 1 Replies View Relatedhow do i configure wireless usb adapter to work with backtrack 4 on vmware
View 2 Replies View RelatedI am a newbie in linux and I curious to learning all about linux, but I have a little trouble. I've just installed my first linux, its Backtrack 4 and my wirelesss network adapter was not detected..please help what I'm soppost to do..i'm using HP CQ40-416AMD Turion X2Broadcom 802.11 b/g WLAN Adapternote :
View 1 Replies View RelatedA friend of mine has a Dell XPS1530 lappy that has a broadcom bcm4328 wireless adapter. I tried installing kismet on it so I can scan for wireless network in range. I configured it with the source driver as bcm43xx in kismet.conf and complained that the driver didn't support monitor mode. It uses the proprietary 'wl' kernel module to operate but kismet can't use the 'wl' module and it says the same error. I tried unloding the wl and b44 modules and loding the b43 driver but then the adapter stoped working. I searched on the net a bit and found out that kisment doesn't work with the prorpietary drivers for that card.
View 14 Replies View RelatedWill the Netgear WPN111 wireless adapter work with Ubuntu 10.10? If so what action is required to get connected with it running Ubuntu 10.10. The adapter works with Windows XP.
View 2 Replies View RelatedDoes Ubunto have a driver for the WPC100 Linksys Adapter wireless card?
View 2 Replies View Relatedi have a zenda w322u usb wireless adapter that gives a good connection to wireless router but seems to give very poor download performance compared to my laptop. Are there settings that i can access for this adapter to improve its performance.
View 6 Replies View Relateddownload and instal tp link wn321g wireless adapter for ubuntu
View 1 Replies View RelatedI have an Atheros AR5007 802.11 b/g WiFi Adapter. I use OpenSuse 11.3, KDE desktop.When I did iwconfig, it displayed the following:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"sami"
[code]....
I recently reformatted and dual partitioned to both Windows 7 as well as ubuntu 10.10. Loading works fine and Windows 7 is 100% operational. I cannot seem to get my wireless network adapter to be read by Ubuntus 'Windows Wireless Drivers' gui. Here are the steps that I have done THUS far, to make sure that we are all on the right path. Before I go any further, my wireless network adapter is an old school WUSB11 Linksys Wireless Network Adapter (running version 2.6).
1) Downloaded and installed "ndiswrapper" from ubuntu's main website. I downloaded the common, utils and ndisgtk files and installed them accordingly.
2) I extracted these three files to the desktop of Ubuntu and accessed the terminal page.
3) From terminal I typed "cd Desktop" to change the directory to the desktop.
4) Next, I typed in "Sudo dpkg -i ndiswrapper-common_1.54-2ubuntu1_all.deb
Sudo dpkg -i ndiswrapper-utils-1.9_1.54-2ubuntu1_i386.deb
Sudo dpkg -i ndisgtk_0.8.5-1_i386.deb"
5) This installed Windows Wireless Drivers gui successfully and I can access it.
6) I have downloaded the driver files for the adapter from the cisco website and searched them for the required files needed.
7) After extracting the .INF file from the "Drivers" directory named "NETUSB.SYS" (I wasn't sure if the other associated files within the same folder needed to be present together with NETUSB so I moved everything to the desktop) I typed in "sudo ndiswrapper -i NETUSB.inf". After accessing the Windows Wireless Drivers gui I have noticed that the 'netusb' driver is present yet under it, the system states "Hardware present: No". This leads me to believe that maybe I installed incorrectly or my "fireware?" is not present? I was reading through the installation guide posted on the ubuntu website that in addition to the .INF file we also need the BIN file(s)? and SYS file(s)?.. The folder with the drivers for my adapter contains a BIN file but it is not within the "Drivers" section of the folder.
9) Upon mousing over the network Icon naturally my hardware is still not present.
10) From what I gather after the system finds the hardware I am to write into the terminal
[Code]....
I want to try to get wireless access to the wifi router with the xbox360 wireless network adapter.Is this possible?
View 1 Replies View RelatedI have recently installed Linux Mint 10 on my laptop. When I look at the Device Manager in Windows 7, it says I have an Atheros AR9285 Wireless Network Adapter. Right now, I am unable to connect to wifi with Linux. What drivers am I able to install, and how would I install them?
View 3 Replies View RelatedI have just completed installing Ubuntu 10.04 LTS. When I click on teh network manager it shows:
Wired Network
disconnected
Wireless Network (Intel PRO/Wireless 2200BG [Calexico2])
wireless is disabled
Wireless Network (Manufacturer RealTek RTL8187 RTL8187 Wireless)
[Code]....
I want to be able to connect through the RealTek wireless adapted.
I am severe wireless problems with Ubuntu 10.04 on my laptop.(Spec below)
I have just performed the first clean install since new. Installed a new Hard Drive as well. The machine and wifi was fine under Ubuntu 9.04.
It is booting much faster now but the wifi keeps dropping off.
Spec:
Machine - Acer Aspire 4310
Wireless card - *-network
description: Wireless interface
product: AR5001 Wireless Network Adapter
vendor: Atheros Communications Inc.
[Code].....
I own an ASUS N61JV-X2 notebook PC. It has an Atheros Communication, Inc. AR9285 Wireless Network Adapter. 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 0280: 168c:002b (rev 01) I cannot see any SSIDs including my home Verizon FiOS 802.11 G WPA2-AES-TKIP encrypted network. I went to Starbucks to try to connect to their free Wi-Fi and I could not make a connection. How do I solve this problem so that I can connect to a SSID of my choice and make a wireless connection while using GNOME 3?
View 2 Replies View Related
