I have installed ubuntu 9.10 on my laptop. It has a 802.11n wireless card.
When I boot up to ubuntu, the wireless does not work. And if I connect to a wire network within ubuntu, it works.
Ubuntu can't detect any of the Wifi network in my home (other laptop can). And I click 'Enable Wireless' in the notification area, it said 'Device not found' for the Wireless Network.
The card is 'Intel Wireless-N Card with Bluetooth'
Can you please tell me how can I setup my wireless card in ubuntu 9.10?
I have had a vz modem card for some time now and it worked fine. However my employer upgraded from a PC5750 device to the new PC770 device. When I plug the old device (now deactivated) it shows and use to work fine. When I plug the new device in Ubuntu does not pick it up and show it in the networking options. I use to see it i n the upper right where I would select my wireless networks. I do get a green light on the card so I know its powered. So what do I need to do to get my Laptop to see the new card? uname -a Linux mylt 2.6.32-32-generic #62-Ubuntu SMP Wed Apr 20 21:54:21 UTC 2011 i686 GNU/Linux
Actually I need the wireless adapter to connect to the AP, so both of the ethernet card should be disabled. Infact, when I try to access to the AP I must disable the eth0 card by using (sudo ifconfig eth0 down), otherwise the route assigns the default gw (192.168.1.1) to the eth0 device and the network is useless.
I'm currently installing Slackware 13.1 on my old Sony VAIO. It's got a wireless card sticking out the side of it, and I just want to make sure I set it all up correctly. I got to the screen where it's asking: static IP DHCP loopback And I'm not sure which one to pick.
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
My name is Matt i've installed Redhat software on my PC using PCI network card.which command can i use to setup my PCI card to be the default network card?
First time linux user, just installed Ubuntu 11.04. I'm trying to setup my wireless, and i'm not sure what to do. I found the network connections manager, and i created a new wireless connection and saved it....
what now? my internet still doesnt work... it says the LAN was last used 20 minutes ago, but i dont have the LAN connected. It says the wireless' "last used" was 'never' How do i make it connect using the wireless connection i just made?
I'm looking for a wireless card that will work out of the box with Ubuntu 9.10. It has to be a pci card. I purchased a Edimax EW-7128G which the reviews said was a great card for linux but was DOA. I could have it replaced or get a different card.
I'm running Ubuntu 10.04 Server. I can't get my Wireless Card & Wired Card to work at the same time. My interfaces file is incorrect, when I comment out 1 of the interfaces the other works. I have attached my interfaces file.
1. If you are on a laptop check that the network function key is turned on. Mine is on F12 and has a bluish light for ON and reddish light for OFF.
2. Go to System > Administration > Users and Groups > Advanced Settings > User Privileges Check you have relevant permissions for Connecting to Wireless Networks and the Internet. (Also turned my audio on here after much trial)
I discovered these after spending hours following up suggestions on these forums. They might not solve everyone's problems but they will hopefully save some of you from fruitless searching
i'm run'n knoppix 6.5 (i think) from a usb stick. under 'ifconfig' it finds 'eth0', but when i put in 'iwconfig eth0' it says: 'eth0 no wireless extensions'. i've tried other linux live cd's but to no avail...interestinly enough, when i run a linux (ubuntu) live cd on my virtual pc it hooks up(?..i figure bcuz its reading from da virtual ethernet?) further more, i researched it to the conclusion that the driver is not being detected. i tried ndiswrapper (under 'puppy') but tht didnt work either ( i've downloaded the lastes version of ndiswrapper and i plan on trying it again w/ the installation disk of the wireless card). however, even in my research i've seen there seem to be a difficulty in getting this particular driver to work? (netgear wg311v3 - wireless g pci adapter) how i can over come this problem? i'm kinda new @ linux, but i like the challenge. it doesnt matter wat linux system (the responder) i'll download it. but i'm really trying to get 1 online cuz i have to learn how to work the packaging systems.
similar to this problem http://www.linuxquestions.org/questi...nstall-673571/ i cannot seem to get the wireless card to turn on. ive tried NTDISGTK and Ntdiswrapper to no avail. it recognizes that the hardware is there, but will not turn it on. in terminal i have tried to force start it, but from what i remember, it gives me an error about authentication (might be access not authentication) ill get back here when i boot ubuntu and take some screenshots, at the moment i's running XP and hating it.
i came across BT4 last few weeks ago, and i tried it in vmware and was tempted to know more, so now i wanna try to install it and dual boot. Here's my problem, when installing the install.sh i get 2 options instead of 3 options in the partioner, so i couldnt install BT4 without erasing my W7, also if i do successfully install it, how do i install drivers for my wireless card, ohh and my laptop is a Acer Aspire 4736G, my wireless card is a intel(R) WiFi Link 5100AGN...
I am trying openSUSE after a long break from Linux, but I am running into the original issue I ran into several years ago which made me decide not to use this distro. My LAN card is working fine, and I can get internet hardwired into my router, but I am not having any luck getting my wireless card recognized or working. Also, my notification area on my taskbar (sorry for the Windows terms) is not showing any sort of network status icon.
I have gone Computer>Install Software> and installed the b43 fwcutter thing from the repos, and have also run the following command in terminal: sudo /usr/sbin/install_bcm43xx_firmware In Network Settings in YaST, my NIC is showing, but I am still not seeing my Wireless card.
I am using Ubuntu 8.04 and when I open up my network settings, It shows my ethernet card and my modem but my wireless card doesn't show up. Under "Hardware Drivers" it says that my driver for my wireless card is a "proprietary driver" and that there is no driver I can get for it for Linux. Is there any way that I can get my wireless card to work? I tried going to the HP website and downloading a driver for it, but all of the drivers only work for Windows....
I have a problem with my Grundig's (model GNB-250D) laptop wireless card. I recently installed Ubuntu 10.10 and tried to use a wireless connection to browse the internet but it didn't detect any, it seemed strange as it worked perfectly on Windows. I can browse the internet fine if I use an Ehternet cable.
I am new to Linux. About 72 hours in, and I must say. I am quite impressed. Except for a small issue. I cannot seem to figure out how to get my wireless card working. I have used the bcm43xx technique with no avail. And am working on ndswrapper. The good news is I think I have the .sys file that works. But I don't have the .inf. However any way I could make this work would be great. Below I have posted my lspci stats.
Lspci: 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) .....
have Unix and Windows experience. So will need some hand-holding.Need help getting my wireless network to work on my newly installed Oracle Linux on Dell laptop.Not sure what wireless card is installed, or it's mac address (though I can boot into windows and get that info I don't want to - it'll be kind of a let down if I can't fix it all thru Linux).Install has detected a Broadcom wired card, but not the wireless. Funny thing is that it detected the Bluetooth
I got a vaio vgn-ar21s laptop that under yast reports to have a tv card: saa7131/saa7133/saa7135 Video Broadcast Decoder
However if I try to choose a tuner (bottom on the right bottom of the yast window for Manual TV card selection, I get "No tuner is available for the selected card".Can this be set up somehow under opensuse 11.2 ? I am running kernel 2.6.31.12-0.2-desktop x86_64
The card works under windows (I can see most digital tv channels [I am in the UK]), but I would prefer to use it under opensuse, of course.
Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
