Ubuntu Networking :: VZ Wireless Modem Card Setup
Jun 15, 2011
I have had a vz modem card for some time now and it worked fine. However my employer upgraded from a PC5750 device to the new PC770 device. When I plug the old device (now deactivated) it shows and use to work fine. When I plug the new device in Ubuntu does not pick it up and show it in the networking options. I use to see it i n the upper right where I would select my wireless networks. I do get a green light on the card so I know its powered. So what do I need to do to get my Laptop to see the new card?
uname -a Linux mylt 2.6.32-32-generic #62-Ubuntu SMP Wed Apr 20 21:54:21 UTC 2011 i686 GNU/Linux
View 2 Replies
ADVERTISEMENT
May 1, 2011
I am facing a problem with the management of my network card after installing Ubuntu 11.04 32-bit Desktop edition.
There are two Network Cards and one USB adapter which I'd like to drive:
- Ethernet controller Broadcom Corporation NetXtreme BCM5703X Gigabit Ethernet (rev 02)
- Ethernet controller Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
- Realtek Semiconductor Corp. RTL8187 Wireless Adapter
Actually I need the wireless adapter to connect to the AP, so both of the ethernet card should be disabled. Infact, when I try to access to the AP I must disable the eth0 card by using (sudo ifconfig eth0 down), otherwise the route assigns the default gw (192.168.1.1) to the eth0 device and the network is useless.
View 2 Replies
View Related
Feb 13, 2010
I am new to Debian. I am trying out the live cd but can't seem to find how to connect to the internet. My setup is Ethernet card and DSL modem, no routers, no wireless. How do I set this up?
View 5 Replies
View Related
Mar 31, 2011
How can I setup a lan connection using wireless pci card on entire system D-link DWA-510 card I have .
View 5 Replies
View Related
Apr 24, 2010
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
View 2 Replies
View Related
Jul 27, 2011
I recently purchased a Spice 3G phone, which can also be used as a Modem. When I plug it into the USB, the phone starts charging.But when I go to Edit Connections--> Mobile Broadband, I cannot see the MODEM there. The Select the device is not highlighted.
LSUSB command shows:
Bus 002 Device 007; ID d324;9003
How do I make it detect so that I can use the phone as Modem.
View 1 Replies
View Related
Apr 14, 2010
I have installed ubuntu 9.10 on my laptop. It has a 802.11n wireless card.
When I boot up to ubuntu, the wireless does not work. And if I connect to a wire network within ubuntu, it works.
Ubuntu can't detect any of the Wifi network in my home (other laptop can). And I click 'Enable Wireless' in the notification area, it said 'Device not found' for the Wireless Network.
The card is 'Intel Wireless-N Card with Bluetooth'
Can you please tell me how can I setup my wireless card in ubuntu 9.10?
View 1 Replies
View Related
Aug 24, 2010
I want to use the two huawei 3G modem card simultaneously.Now by using pppd,I can got the PPP connection separately.but when I did them simultaneously,only one can successfully establish the ppp connection，the other will be blocked.If i kill the pppd process which already establish the ppp connection，the blocked one could then connect to the ISP and establish a ppp connection successfully. If I want to use them simultaneously,how should I do.I think maybe my linux only support only one pppinterface
View 2 Replies
View Related
Jul 11, 2010
I am using Linux Mint 9 Gnome: Isadora (since the same Network Manager applet is used in Ubuntu, I am asking the question here too)I was trying to configure my wireless card to connect my PPPoE connection by using the command pppoeconf wlan0 and also pppoeconf.I was not able to dial my PPPoE connection when connected via Wi-Fi. When I restarted my system, in the Network Manager, under Wireless Networks it says "Device not managed". Now I am not able to use my Wi-Fi card at all and cant connect to my Wi-Fi modem.
There is no hardware Wi-Fi switch, only the key combination Fn+F2 to enable or disable the wireless card.I have used the key combination Fn+F2 (which enables or disables the Wi-Fi card) many a times, but the same thing is displayed in the network manager.If I use LiveCD mode and use any distro even Isadora, the Wi-Fi works fine.My ethernet connection is working fine. I can connect to the internet if I connect my modem using Ethernet port.
View 1 Replies
View Related
Jan 24, 2011
How do I get information about the SIM card of my USB broadband modem, for example it's phone number, serial number and so on, in Ubuntu 10.04?Not about the usb modem itself - just the SIM card inside it.Is there a way to probe it from the terminal, like you probe for usb devices with lsusb?
View 3 Replies
View Related
Jul 13, 2009
how can i connect to the internet using modem card?
Intel d915,3GHz pinless,Lucent Modem
View 6 Replies
View Related
Dec 29, 2010
I'm currently installing Slackware 13.1 on my old Sony VAIO. It's got a wireless card sticking out the side of it, and I just want to make sure I set it all up correctly. I got to the screen where it's asking:
static IP
DHCP
loopback
And I'm not sure which one to pick.
View 5 Replies
View Related
Aug 21, 2010
I'm running Ubuntu 10.04 Server. I can't get my Wireless Card & Wired Card to work at the same time. My interfaces file is incorrect, when I comment out 1 of the interfaces the other works. I have attached my interfaces file.
View 2 Replies
View Related
Jan 15, 2010
ubuntu I can not use a wireless modem huawei 160.type can only be used in windows.well to be used in my ubuntu linux? whether there is a script that used.
View 2 Replies
View Related
Apr 8, 2010
My wireless modem has disappeared from the connection list at the top of the page. Strangely, a guest connection on that same modem is still visible but won't connect. I added the modem back in as a new connection and it was added to the list but it was greyed out and I still can't connect to it. The problem could, of course, be in the modem but I have no way to check that. Reset is not working. Lan connection to the modem works fine. This is the second time this has happened in the last week and I ended up reinstalling Ubuntu. This gave me back the wireless connection. I don't really want to have to do that again. Is there anything I can check in Ubuntu?
View 1 Replies
View Related
Jan 1, 2011
I installed 10.10, I'm using a HP tower with a cisco usb ae1000 modem. I have been on Linux all of 12 hours. I had installed on a old laptop, and hard wired to the router. I really liked the OS. And Long short I killed the laptop, literally.
So I partitioned the family tower, but I cannot connect wirelessly. And to run hard wire to the router would mean a complete tear down of my desk and set up in the living room area, and that will not help out the marriage long/short term.
on the internet connection and I gone through the panels trying to set up the connection but no luck. I'm running Vista and Ubuntu 10.10. I using vista to post here now.
How do I get it to find the wireless router and set up my connection without being hardwire to the router itself.
View 9 Replies
View Related
May 22, 2011
I've recently installed Natty and the only problem I have with it so far is attempting to connect my Huawei E5830 Three Wireless modem via USB and successfully connecting to the Internet from it. I've fiddled around with the network settings and nothing, I've also done some work in the Terminal to try and correct the problem.
View 1 Replies
View Related
May 26, 2011
i have a samsung laptop.i recently installed ubuntu 11.04 on it.
I have a huawei WA1003A modem .In windows i connect to my modem wirelessly using (WLAN) facility after connecting it shows it has limited connectivity with the modem and then i connect to BSNL using username and password..then i get connected to internet..
In ubuntu I conncted to internet using the cable by making a new dsl connection i provided my user name and password. and then i switched on the modem connected the cable and connected to dsl connection and internet was connected.. . i want to connect it wirelessly.
View 2 Replies
View Related
Dec 4, 2010
Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
View 6 Replies
View Related
Sep 27, 2010
I have a 3g data card(LW272 GSM/WCDMA USB Modem with HSPADataCard) which is a type of multi-mode, 3G modem or card, applicable to 2G/3G networks; but it doesn't get recognised in Ubuntu 9.10. Actually, this device came with a software(for linux too) which makes calls and sms possible simultaneously while surfing. But while installation(from root terminal) i see a repeated trials of connecting to modem but it does not find the device(something wrong in installation), and the interface of the software also shows "No(U) Sim". Anyhow it doesn't bother me much if i m not able to avail the additional services( call and sms), but what i need is to make the modem recognisable so that i could configure the connection.
View 3 Replies
View Related
Feb 7, 2010
3G USB modem, in and using wireless router out (via ethernet) to lappy, Wii ect.We don't have a phone line just mobile phone and mobile internet because it is mobile.I have a wireless router only but need wireless to improve my standing within the house because I am seen as a net hog!
I did come across a Virgin wireless modem but it is soooo painfully slow (tested it against the USB dongle modem 3-4kb same test 1 min later 280-300kb's USB.) The wife could make herself a cuppa just waiting for the facebook login page to load!Would it need to pass on the connection bcause the USB is fully setup? then wireless is setup or would it be required to have a 3rd security setting ect in between?It would be good to use a low spec computer because I have a few. Headless too, maybe?
View 8 Replies
View Related
Jul 13, 2011
I am using Ubuntu 11.04 and a Huawei USB modem to connect to internet. Most of the time when I start computer it is not detected my system. Then I use to reboot and then it gets detected automatically. That means its drivers are now loaded. But I don't know why drivers are not loaded when I start first time.
View 1 Replies
View Related
Jul 28, 2011
I have an Ubuntu server that I need to access remotely while I am at school. The server's internet connection comes first through a DI-604 broadband router and then through a Netgear Wireless router:
ethernet wall jack --> Broadband Router --> Wireless Router --> Server's ethernet port
I can manage to get the SSH to work with the current IP address (dynamic) by connecting the server directly to the broadband router, but I cannot set up DNS (ddclient on the server, Namecheap for domain registrar and nameserver) with it. I can set up DNS on the router with no issue, as it has the DNS client built in, but I cannot get the SHH to connect through both the modem and the router as mentioned above. Best case scenario, this can be fixed without having to get anything new, but if that is the case, recommendations of a new setup
Other reference info - ISP at server is Verizon Fios, broadband router set to PPPoE.
View 1 Replies
View Related
Jan 22, 2010
I just bought a TRENDNET TDM C4000 (=modem/ wiredrouter) and got it working. If I connect my computer with through the ethernet port directly, the internet will work. However, when I try connecting the ends of the ethernet cable on the modem and my wireless router, it's not transmitting. I know I set up the wireless router correctly because it worked with my previous modem. I just need to know how to configure my modem so that it works with my wireless router (D-Link DI-524).
I have a long wired ethernet wire to satisfy my academic needs for the internet at the moment but my mother is not able to surf the internet and it would be more convenient for myself to put the wire back to my desktop and have my laptop browsing wirelessly.
View 1 Replies
View Related
Jan 28, 2010
Earlier today I decided I wanted to switch back over to ubuntu, my internet was working fine, but as soon as i reformatted to Linux my modem stopped showing any lights under ADSL - TX and RX. and I can't connect to my wireless connection anymore. What should I doooooooo
View 1 Replies
View Related
May 14, 2010
Without Gdm (The GUI Desktop running), or an Internet connection, how does One get pppd or wvdial to connect to a wireless broadband modem?I'm SURE this can be done with any modern Distro without additional downloads...but seem to be missing some crucial step...? I've been trying things like: (scrips for pppd and chat and ln {links} ttyACM0 to /dev/modem?) the modem is definitely on ttyACM0.
ln -sf /dev/ttyACM0 /dev/modem
/etc/ppp/chat-script
#!/bin/sh
[code]....
View 1 Replies
View Related
Mar 30, 2010
I have a dell 1521 and I can't get internet working, I thing the driver is no working with ubuntu 9.10
View 1 Replies
View Related
Dec 31, 2010
I have lenovo thinkpad, T61 with Intel 4965AGN wireless card. It is a N card, it works under N mode in windwos, but not in Ubuntu (10.10). I installed ndiswrapper and got the windows xp drivers for this card. the issue is that i got an error when installing the drivers and since then I cannot use wireless.
The error i got is: Code: Module could not be loaded. Error was: FATAL: Could not read '/lib/modules/2.6.35-24-generic/kernel/ubuntu/ndiswrapper/ndiswrapper.ko': No such file or director I unistalled the driver, but now under network connections no wireless connections appear, nothing. I cannot use wirless anymore.
View 9 Replies
View Related
May 5, 2011
wlan0 Authentication capabilities :
WPA
WPA2
CIPHER-TKIP
CIPHER-CCMP
Those are my authentication capabilities, obviously. I am using a WEP encryption for my wireless router and according to this, it will not allow me to connect. Is there anyway to allow that? The wireless card works just fine in Windows, even on the same network encryption type. Using a Intel Wireless/Pro 4965 ag. Note* this is my mother's router and whatnot. She won't change it the encryption type.
View 2 Replies
View Related
Jun 17, 2011
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
View 9 Replies
View Related
