Realtek 8111 / 8168 LAN Driver will not install on RHEL 5
[root@localhost r8169-6.002.00]# make clean modules
make -C src/ clean
make[1]: Entering directory `/root/r8169-6.002.00/src'
rm -rf *.o *.ko *~ core* .dep* .*.d .*.cmd *.mod.c *.a *.s .*.flags .tmp_versions Module.symvers rset
make[1]: Leaving directory `/root/r8169-6.002.00/src'
make -C src/ modules
[Code]....
I m unable to use my lan card on rhel5 linux lan card no :- is realtek 8168/8111
View 1 Replies View RelatedHow to install Realtek 8139 Ethernet driver? I tried downloading from realtek website. there is no driver for Realtek 8139. Although i downloaded the driver for 8168 for Linux, i could not install it after uncompressing the tar file
View 1 Replies View RelatedI made the debian installation 8.3 more adapters wi fi and cable do not connect to the network ... How I could solve this?
View 0 Replies View RelatedInstalling Fedora13 Kernel 2.6.33 killed my RealTek NIC. I found the following page which helped a little bit: [URL]. Unfortunately the card still does not work.
If I do
lsmod | grep r81
I get:
r8168 91833 0
So I am not sure the really the new module is loaded. Doesn't anybody have the realtek working with fedora13 ?
I have installed Ubuntu 9.04
uname -r
2.6.28-11-generic
Checked cable/network with 386Box running Ubuntu 8.04 all OK. Could not get Realtek 8168 on mother board to work on Gigabyte H55M-S2H motherboard. I tried to install r8168 driver but no luck ... so I bought another Linux compatible card which turned out to be a RTL8139c (eth1) and the driver I am using on this is card is 8139too.
[Code]....
My preference would be to get the motherboard ethernet working but perhaps the card may be easier to get working. Anyway after searching the net for ideas and trying different things I've just about given up. I have reinstalled Ubuntu today so eth0 is back to using the r8169 driver. I'm no expert so my attempts at following other recipies have so far failed. From what I have read the 8139too driver should have worked with the RTL8139C chip so I have run out of ideas. I must be doing something wrong.
I hope I'm posting in the right forum here, but I'm trying to install a realtek wireless driver and make goes okay, but when I get to make install it says permission denied when trying to create a file in a folder near the end of the process. Is there anyway to fix this? What can I do?
View 2 Replies View RelatedHow can i install Realtek HD Audio Driver??
I Downloaded The Driver From Realtek Website
http://img517.imageshack.us/i/20100827183305.png/
Then
http://img821.imageshack.us/i/98431356.png/
i dont know how to install this driver from this file
i want to use my Sound Card Features ( like Windows 7)
Ex.
http://smg.photobucket.com/albums/v1...ealtekHDMI.jpg
I want to install this URL...How to? Because i downloaded the tar.gz2 format of it.And i dont know what to do.
View 2 Replies View Relatedi use fedora11 and try to use wireless i find driver for chip Realtek RTL8187 but want to know command to install it. i save folder of driver on desktop in folder name rtl8187_linux_26.1010.0622.2006has like this
[Code]....
I just installed FC14 on an ASUS Eee Pc with Realtek WNIC (RTL8191SE) and I am trying to install the driver for the WNIC which I downloaded from Realtek's website. There is a problem though during the 'make' command and this is the output
[code]...
what is this 'build' that is looking for? what can I do to fix this?
There seems to be some trouble with 8139too not working in a previous post. Has anyone found a solution to this? ubuntu version 2.6.24 (Hardy Heron?). Followed all known possibilities but information is all mostly out of date. module 8139too.ok? does not load. Following makefile on 8139too.c supplied, after altering to suit my version, comes up with 3 pages of errors?. ifconfig shows nothing for eth0like the last person markjuggles i have hit a brick wall here. Am I wasting my time?
View 10 Replies View RelatedNow, my issue is that I have no access to ethernet in my apartment so I need to rely on wifi for my install. But during the install when it is looking for the network hardware it never sees the TP-Link Dongle and never asks if I wan to load the firmware. I even tried it with the CD image that has the non-free drivers included but it never asks for the drivers. Any other distro, like Linux Mint 7.3, sees the dongle fine.
So is there a way to force load the realtek-firmware drivers during install?
I tried to install the latest RealTek driver for Linux and it has wiped all my devices. I've tried reinstalling the alsa-base packages but it hasn't worked
View 4 Replies View RelatedI've got a Puppy system running version 4.3.0 that I'm trying to get on the home network. I'm using a D-Link DWA-130 (H/W revision C), which has a Realtek RTL8192U chipset. I got the drivers off of D-Link's website, and they compiled and installed just fine, but when either a) I try to connect to the network, or b) while I'm browsing the web, the system locks up completely. No mouse, no keyboard, no Ctrl-Alt-Bksp to get out of X, nothing.
I'll outline my steps: Install Puppy using a "Full" HDD install (not "Frugal"). Copy the "devx_430.sfs" file (which I got from the Puppy website) from a thumb drive to the "my-documents" folder (although the exact location proabably doesn't matter). Mount it, cd to the mounted directory and execute "cp -a --remove-destination ./* /" and "sync". Copy the kernel source for 2.6.30.5 ("kernel_src-2.6.30.5-patched.sfs4.sfs") to the same directory. Mount it and execute the same commands as before. Copy the folder containing the RTL8192U drivers ("rtl8192u_linux_2.6.0006.1031.2008") to the root directory (i.e. "/"). cd to the folder in the terminal and run "make", "make install".Reboot the machine. Set up networking using the Puppy Internet Connection Wizard. HERE'S WHERE IT SCREWS UP: It connects, but after a while (e.g. just after logging into LQ through it, as a test) it freezes the entire system.
I have to do a hard reboot ("panic button"), then a soft reboot (for some odd reason the usb module won't load after a hard reboot, so the mouse won't work) to get the system working again, only to have it lock up again once it connects to the network.
Are these drivers broken? Outdated? Is there anything I can do to fix this? EDIT: I should add that this only occurs when the adapter is plugged in. If I boot the system with it unplugged, it works fine (probably because it never loads the kernel module).
I have been having trouble with the install of Ubunto in general. First problem is that my realtek network drivers rtl8168 are giving me some problems. I have followed advice from other threads for disactivating the NIC and disconnecting the power for 10seconds. This works in that Ubunto can recognize the hardware (hardware active), but it says it is not in use. Furthermore, I try to define the IP address manually and it does not allow me to press apply. Therefore I cannot connect to the internet.
I though I would try a fresh install of the latest Ubuntu. I did not have the internet connected (due to drivers). After the partitioning section (I partitioned over Ubunto 9.10), on the screen where it says select Username, computer name etc. some files were loaded, and at the end it says �ready when you are�but I was not able to move forward. I don�t now why. Ultimately I reboot the computer Now I get this message upon booting (I am still booting from USB)
GRUB Loading
error: unknown filesystem
grub rescue
i have rtl 8111/8168b gbe ethernet card. i hav downloaded its tar file from from gigabyte website.......kernel version is 2.6.18-8.el5
View 1 Replies View RelatedI am in attempt to add a pvscsi driver into RHEL 6 Beta OS. What I did is followed this:
1. Downloaded the complete ISO into /home/jack/RHEL folder
2. Follow these steps:
#cd isolinux/
boot.cat grub.conf isolinux.bin splash.jpg vesamenu.c32
boot.msg initrd.img isolinux.cfg tmp vmlinuz
call initro memtest TRANS.TBL
[Code].....
I tested with RHEL6 Beta and they don't include pvscsi driver we use for Vmware ESX.We did asked them to include this driver with new RHEL 6 Beta 1 but they din't. Now we expect it to be shipped with RHEL 6 Beta 2. How can I track the same beforehand. Is there any repository where can I track whether they have plan to ship it or not?
View 2 Replies View RelatedI just checked the Realtek website and they have a new Linux Driver for the RTL8185. The new driver is dated 6/26/2009. So it is quite recent. I would have thought it might have gotten into FC11.
I have 2 questions. Has anyone tried it? What would be the steps to install it?
Where can I get the Realtek ALC883 driver for Ubuntu?
View 1 Replies View Relatedtrying to get my little Encore USB wireless adapter to work on several flavors of Linux (Ubuntu 10,10, ElementOS, Xubuntu, and Puppy), I emailed tech support at Realtek. I asked where is the Linux driver for this product? I did this because there were no Linux drivers posted on their site and everyone here (and on Newegg) is jumping though hoops trying to get a working wireless connection with the Encore and similar dongles that use the RT8187b chipset. I didn't expect an answer, but felt better after my little vent. I get an email from Realtek with a driver. Realtek needs to promote Jerry -- a beacon of customer service in the age of the "get lost" school of customer relations. I have attached the driver below. Caveat: I have not yet compiled the driver, so I don't know much more about it than I've said already, although the archive appears to contain the source code.
View 3 Replies View RelatedI got a new laptop and I install Debian Jessie, but the SD Card reader is not working at all. When I list the devices with lspci it list the device:
07:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5249 PCI Express Card Reader (rev 01)
I am using ubuntu 10.04lts on my compaq615 laptop, which has a realtek wireless card, with which I had a few issues to get it to work.
Here is what I had to do:
When I do this, it works beautifully, after setting my router to open I may add.
So, as I said it is probably the fastest wireless I have ever experienced, but my problem is this, everytime I switch my laptop on I have to re-install, starting at:
when I updated from 10.04 to 10.10 beta, I lost my wireless on my Gateway MX3410 laptop. In 10.04, the wireless Realtek RTL8185 card was auto-detected, worked with the default driver.
So I installed the linux driver version of Realtek RTL8185. Although the driver shows up in the "Additional Drivers" panel under "Administration", the computer is not recognising the driver.
Below is all the specs of the current situation.
Gateway MX3410 Computer
OS: Ubuntu maverick (development branch)
2.6.35-22-generic x86_64
lspci:
Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller (rev 20)
lsusb:
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[Code]....
Sound works with Jaunty Jackal. Does not work with Lucid Lynx. It appears that Lucid Lynx will only acknowledge that I have a modem as a sound card. I just want to add my RealTek ALC880 driver so the sound will work. I've made sure that I have audio privileges, I made sure that nothing is muted using alsamixer. I've been looking at threads and documentation for four days just to fix the sound issue and so I can be prepared in case this 'feature' ends up being continued in Maverick Meerkat and when I upgrade I can use M.M. with minimal fuss.
View 1 Replies View RelatedI printed off the Readme file from RealTec and went though the following procedure. If anyone spots a glaring error could you please advise and I will try and fix. I changed to superuse using : sudo su and entered my password. All good so far.I was already in the directory containing the downloaded RealTec driver. I downloaded RLT8192SE ver 0019 as this was the closest to my hardware version and the latest driver available.
I used the command : make
and then : make install
Both these commands ran ok. However when I rebooted and activated wireless using Fn F10 on the laptop I was still disconnected from WIFI.
I then used : iwconfig wlan0 up
but this resulted in an error (see below)
root@Ubuntu:/home/jon/LDD/Drivers/test# iwconfig wlan0 up
iwconfig: unknown command "up"
root@Ubuntu:/home/jon/LDD/Drivers/test# ifconfig wlan0 up
SIOCSIFFLAGS: Operation not permitted
my Ethernet card stopped responding a few days after installing Ralink Wireless Card Driver for Linux. I have tried installing the drivers from Realtek's site, but it fails. I also have tried reinstalling the network manager, and that still didn't help any. I have also tried looking online for any post or blog that could help, but that also turned up nothing. The Computer is a new 2010 / 2011 (bought it on new years eve) HP Pavilion desktop that came with windows preinstalled.
View 6 Replies View Relatedanyone tried to run wifi-card based on this chip? In coming days I will build myself a proprietary driver for 2.6.27.7 kernel. I mostly aware about patches for wpa_supplicant. Should I use a source for wpa_supplicant from slackware 12.2 distro or a new version? Do you know about any other prerequisities (requirements, dependencies) for building this proprietary driver?
View 2 Replies View RelatedI've just installed Ubuntu 10.04 on my samsung n150. It has the 8192 device in it. Have installed ndiswrapper, however cannot get the drivers for it. How to fix/where to get the driver from so I can get my wireless card working again.
On lspci:
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) .....
I think the driver may be there, however I just can't 'enable' it. On my laptop there is a blue light saying that wifi is enabled however who knows.