I just checked the Realtek website and they have a new Linux Driver for the RTL8185. The new driver is dated 6/26/2009. So it is quite recent. I would have thought it might have gotten into FC11.
I have 2 questions. Has anyone tried it? What would be the steps to install it?
when I updated from 10.04 to 10.10 beta, I lost my wireless on my Gateway MX3410 laptop. In 10.04, the wireless Realtek RTL8185 card was auto-detected, worked with the default driver.
So I installed the linux driver version of Realtek RTL8185. Although the driver shows up in the "Additional Drivers" panel under "Administration", the computer is not recognising the driver.
Below is all the specs of the current situation.
Gateway MX3410 Computer
OS: Ubuntu maverick (development branch)
2.6.35-22-generic x86_64
lspci:
Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller (rev 20)
lsusb:
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[Code]....
Running Linux mint 10 After the installation the wireless connection worked but it was very weak and intermittent. The icon would show 1 bar or none. iwconfig showed the rate at 1Mb/s. The same card worked fine in windows and on a 32bit version of linux. Installed new driver from realtek. Now the iwconfig readings look good and the icons shows 2 and sometimes 3 bars. But it will not connect at all! I even turned off all security on my router but it would not connect.
View 14 Replies View RelatedI installed a wireless pci nic in a desktop. The wireless nic works with puppy linux 5.0.1 using the built-in rtl8185 driver. I ran make and ./wlan0up, then ifconfig. I see the lo and wlan0. If I see wlan0, then I am assuming that the driver is working? I use the same driver in a laptop, but I just run the script ./wlan0up and never had to seek anp address. The card is an imicro wireless pci card. The access point is the apple airport. I tried the dhcp script, but get an error.
View 1 Replies View Relatedan old Compaq Presario 8000, which I reluctantly took, as I tend to end up with more computers than I use and more or less end up acting as a disposal agent. It's a 2.4Ghz machine, which will suffice for whatever I felt like installing on it.I have a generic wifi pci card with a Realtek RTL8185 chipset in it, which I never used and thought I'd set up that computer with it. Hadn't installed Slackware 13 on anything, and it's a distro I like so I went at it.Install went well, no problems there, but I've used Slackware for about 9 years so I'm readily familiar with that end o' things.
I found the rtl8180 module to be causing problems. It would load on boot, but wouldn't bring up a wireless interface. I was able to remove the module with 'rmmod rtl8180' well enough, but when I would load it again with 'modprobe rtl8180', the system would lock. Tried that a few times, same result. I ran across mention of a driver on Realtek's web site, so I downloaded and installed it. That one is identified as 'r8180'. I added 'rtl8180' to the module blacklist to prevent it from being loaded at boot, and proceeded to set up wpa_supplicant.conf for my WPA-PSK connection. Came up without a hitch.The connection is stable thus far, with a respectable link quality. The Realtek driver can be found here.I thought I might document my solution here in case someone else runs across the same issue that I experienced.I'm thinking of slapping another wireless NIC in that computer, or perhaps testing with multihoming possibly. This computer will probably end up as an AP for relaying my wireless traffic to an AP downstairs. I have one USB NIC (Alfa AWUS036S)with a 5dB antenna that has a strong signal, but the ones of more a common variety could use a little help
i use fedora11 and try to use wireless i find driver for chip Realtek RTL8187 but want to know command to install it. i save folder of driver on desktop in folder name rtl8187_linux_26.1010.0622.2006has like this
[Code]....
I'm having some issues with my RTL8185 on a fresh install of Lucid on a quad core x64.It connects, but the signal strength is much weaker than it should be. I did some searching and found others with the same problem, but couldn't find any solutions. First off, I have build-essentials, and the kernel headers.I downloaded the latest drivers off the realtek website, started following their directions and got this on the first step:
Code:
pvfjr@acer-desktop:~/Desktop/rtl8185$ sudo make
make[1]: Entering directory `/usr/src/linux-headers-2.6.32-22-generic'
[code]....
trying to get my little Encore USB wireless adapter to work on several flavors of Linux (Ubuntu 10,10, ElementOS, Xubuntu, and Puppy), I emailed tech support at Realtek. I asked where is the Linux driver for this product? I did this because there were no Linux drivers posted on their site and everyone here (and on Newegg) is jumping though hoops trying to get a working wireless connection with the Encore and similar dongles that use the RT8187b chipset. I didn't expect an answer, but felt better after my little vent. I get an email from Realtek with a driver. Realtek needs to promote Jerry -- a beacon of customer service in the age of the "get lost" school of customer relations. I have attached the driver below. Caveat: I have not yet compiled the driver, so I don't know much more about it than I've said already, although the archive appears to contain the source code.
View 3 Replies View RelatedI am using ubuntu 10.04lts on my compaq615 laptop, which has a realtek wireless card, with which I had a few issues to get it to work.
Here is what I had to do:
When I do this, it works beautifully, after setting my router to open I may add.
So, as I said it is probably the fastest wireless I have ever experienced, but my problem is this, everytime I switch my laptop on I have to re-install, starting at:
I printed off the Readme file from RealTec and went though the following procedure. If anyone spots a glaring error could you please advise and I will try and fix. I changed to superuse using : sudo su and entered my password. All good so far.I was already in the directory containing the downloaded RealTec driver. I downloaded RLT8192SE ver 0019 as this was the closest to my hardware version and the latest driver available.
I used the command : make
and then : make install
Both these commands ran ok. However when I rebooted and activated wireless using Fn F10 on the laptop I was still disconnected from WIFI.
I then used : iwconfig wlan0 up
but this resulted in an error (see below)
root@Ubuntu:/home/jon/LDD/Drivers/test# iwconfig wlan0 up
iwconfig: unknown command "up"
root@Ubuntu:/home/jon/LDD/Drivers/test# ifconfig wlan0 up
SIOCSIFFLAGS: Operation not permitted
my Ethernet card stopped responding a few days after installing Ralink Wireless Card Driver for Linux. I have tried installing the drivers from Realtek's site, but it fails. I also have tried reinstalling the network manager, and that still didn't help any. I have also tried looking online for any post or blog that could help, but that also turned up nothing. The Computer is a new 2010 / 2011 (bought it on new years eve) HP Pavilion desktop that came with windows preinstalled.
View 6 Replies View RelatedI've just installed Ubuntu 10.04 on my samsung n150. It has the 8192 device in it. Have installed ndiswrapper, however cannot get the drivers for it. How to fix/where to get the driver from so I can get my wireless card working again.
On lspci:
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) .....
I think the driver may be there, however I just can't 'enable' it. On my laptop there is a blue light saying that wifi is enabled however who knows.
I'm having trouble with my Samsung Netbook N220 and its Realtek 8192 wireless card and could use some help with diagnostics. I would like to use the netbook as a server and after a day or so the system stops responding. What I'd like to know:
- What do the "========>ieee80211_parse_info_param(): athros AP is exist" spam messages actually say? Does anyone else have this and stability problems?
- Why is the realtek driver package not working?
I'm running Ubuntu Netbook 10.04/Kernel 2.6.32-24-generic. Initially the card was unable to connect, so I installed the Realtek driver rtl8192se_linux_2.6.0017.0507.2010 which adds a kernel module r8192se_pci.ko. At first my system was hanging during bootup. I then restored /lib/modules/2.6.32-24-generic and now the card is connecting but the system is unstable. The 2.6.32-23-generic kernel, modules listed below, still has modules as installed by the realtek driver and is not working. Below the drivers supplied by ubuntu
./2.6.32-24-generic/kernel/ubuntu/rtl8192se/r8192se_pci.ko
./2.6.32-24-generic/kernel/drivers/staging/rtl8192su
./2.6.32-24-generic/kernel/drivers/staging/rtl8192su/r8192s_usb.ko
[code].....
Today I realized that my newly installed Natty does not recognize the Ethernet port, I used to have it when I was working on the Ubutnu 10.10. The following is the output (only the network related part) of lshw command:
Code:
-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
[code]...
There seems to be some trouble with 8139too not working in a previous post. Has anyone found a solution to this? ubuntu version 2.6.24 (Hardy Heron?). Followed all known possibilities but information is all mostly out of date. module 8139too.ok? does not load. Following makefile on 8139too.c supplied, after altering to suit my version, comes up with 3 pages of errors?. ifconfig shows nothing for eth0like the last person markjuggles i have hit a brick wall here. Am I wasting my time?
View 10 Replies View RelatedI hope I'm posting in the right forum here, but I'm trying to install a realtek wireless driver and make goes okay, but when I get to make install it says permission denied when trying to create a file in a folder near the end of the process. Is there anyway to fix this? What can I do?
View 2 Replies View RelatedI've got a Puppy system running version 4.3.0 that I'm trying to get on the home network. I'm using a D-Link DWA-130 (H/W revision C), which has a Realtek RTL8192U chipset. I got the drivers off of D-Link's website, and they compiled and installed just fine, but when either a) I try to connect to the network, or b) while I'm browsing the web, the system locks up completely. No mouse, no keyboard, no Ctrl-Alt-Bksp to get out of X, nothing.
I'll outline my steps: Install Puppy using a "Full" HDD install (not "Frugal"). Copy the "devx_430.sfs" file (which I got from the Puppy website) from a thumb drive to the "my-documents" folder (although the exact location proabably doesn't matter). Mount it, cd to the mounted directory and execute "cp -a --remove-destination ./* /" and "sync". Copy the kernel source for 2.6.30.5 ("kernel_src-2.6.30.5-patched.sfs4.sfs") to the same directory. Mount it and execute the same commands as before. Copy the folder containing the RTL8192U drivers ("rtl8192u_linux_2.6.0006.1031.2008") to the root directory (i.e. "/"). cd to the folder in the terminal and run "make", "make install".Reboot the machine. Set up networking using the Puppy Internet Connection Wizard. HERE'S WHERE IT SCREWS UP: It connects, but after a while (e.g. just after logging into LQ through it, as a test) it freezes the entire system.
I have to do a hard reboot ("panic button"), then a soft reboot (for some odd reason the usb module won't load after a hard reboot, so the mouse won't work) to get the system working again, only to have it lock up again once it connects to the network.
Are these drivers broken? Outdated? Is there anything I can do to fix this? EDIT: I should add that this only occurs when the adapter is plugged in. If I boot the system with it unplugged, it works fine (probably because it never loads the kernel module).
I just installed FC14 on an ASUS Eee Pc with Realtek WNIC (RTL8191SE) and I am trying to install the driver for the WNIC which I downloaded from Realtek's website. There is a problem though during the 'make' command and this is the output
[code]...
what is this 'build' that is looking for? what can I do to fix this?
I recently installed realtek sound driver software in my system,
but after installing it,the speakers are not working....
I'm using fedora 13(x86_64).
i just want to make my system speak,like before....
how to make my speakers work ?
I have been trying searching and reading for a few days now and I have had no luck getting a Encore ENLWI-G2 wireless pci adapter to install. I downloaded their Linux driver [URL]...and I keep getting errors on the makedrv (attached). I get a couple "make: *** /lib/modules/2.6.18-92.el5/build: No such file or directory. Stop. " errors but the modules appear to be there.
I have not touched Linux in 5 or 6 years, so pretty rusty. I have a call in at Encore support and will post their solution if they get to me first.
I'm new to Fedora and just installed the latest version on my Compaq Presario CQ56. Everything except for the WirelessLan seems to be working. The driver is missing, which I've already downloaded and when trying to run the "make" command it tries to cd into the following directory:/lib/modules/2.6.35.6-45.fc14.i686/build
whereas the build folder is actually a dangling symlink which it for some reason can't access. Is there anything I can do to solve this issue?
I have a Samsung N130 with a Realtek 8192 wifi card (possibly 8192e, I'm not sure) and I am trying to run Fedora 12 on it. I used to run Ubuntu until trying their latest beta and realizing it's not very good, so I looked for something else. Ubuntu was at least easy to get the wifi working with just a few quick commands that were written out, word for word, in order, on the Ubuntu forums. I tried openSUSE on here and it didn't have wifi working out of the box either but people on their forums refused to give me actual instructions and just kept bumping me from thread to thread with people giving vague advice or else just telling me I was looking in the wrong place. I'm hoping that someone can give me clear and detailed instructions on how to get this wifi card working. Keep in mind that I am coming from Ubuntu and so I'm not super comfortable in CLI, if I need to do some CL stuff I will need clear and detailed instructions on how to do that.
View 4 Replies View RelatedWhere can I get the Realtek ALC883 driver for Ubuntu?
View 1 Replies View RelatedHow can i install Realtek HD Audio Driver??
I Downloaded The Driver From Realtek Website
http://img517.imageshack.us/i/20100827183305.png/
Then
http://img821.imageshack.us/i/98431356.png/
i dont know how to install this driver from this file
i want to use my Sound Card Features ( like Windows 7)
Ex.
http://smg.photobucket.com/albums/v1...ealtekHDMI.jpg
I've got Fedora 14 (2.6.35.12-90.fc14.i686.PAE) installed and i'm trying to use hostapd with my Realtek RTL8191S USB WLAN Adapter, but can't get it to work. The driver i'm using is : rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 601.tar.gz
[Code]....
I got a new laptop and I install Debian Jessie, but the SD Card reader is not working at all. When I list the devices with lspci it list the device:
07:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5249 PCI Express Card Reader (rev 01)
I want to install this URL...How to? Because i downloaded the tar.gz2 format of it.And i dont know what to do.
View 2 Replies View RelatedSound works with Jaunty Jackal. Does not work with Lucid Lynx. It appears that Lucid Lynx will only acknowledge that I have a modem as a sound card. I just want to add my RealTek ALC880 driver so the sound will work. I've made sure that I have audio privileges, I made sure that nothing is muted using alsamixer. I've been looking at threads and documentation for four days just to fix the sound issue and so I can be prepared in case this 'feature' ends up being continued in Maverick Meerkat and when I upgrade I can use M.M. with minimal fuss.
View 1 Replies View Relatedanyone tried to run wifi-card based on this chip? In coming days I will build myself a proprietary driver for 2.6.27.7 kernel. I mostly aware about patches for wpa_supplicant. Should I use a source for wpa_supplicant from slackware 12.2 distro or a new version? Do you know about any other prerequisities (requirements, dependencies) for building this proprietary driver?
View 2 Replies View RelatedJust installed f14 on my Toshiba laptop, which has a realtek ethernet card. i installed the drivers from the realtek site with no issues (also, i know the card is good, i had it working on suse a while back). No matter what I try, i cannot seem to get the computer to recognize there being a wireless connection (tells me no such thing as wlan0).ifconfig shows the following:
Code:
# ifconfig
eth0 Link encap:Ethernet HWaddr 88:AE:1D:F4:AD:88
[code]...