I used usb_modeswitch but the result was "No default vendor/product found." But usbmod_switch.conf file has all the vendor & product id contained in it. And modeprobe is also not effective. Even Sakis3g script fails to switch my datacard into modem. How to use BSNL Data Card in Fedora 13?
View 1 RepliesSince installing F11, my Canon LIDE 50 scanner refuses to work. xsane 0.996 produces an error message: Failed to start scanner: Error during device I/O.
sane-find-scanner says it is there: found USB scanner (vendor=0x04a9 [Canon], product=0x2213 [CanoScan], chip=GL841?) at libusb:001:006 But scanimage -L claims: No scanners were identified.except once when it admitted: device `genesys:libusb:001:006' is a Canon LiDE 35/40/50 flatbed scanner
I reluctantly tested the scanner on a Windoze machine and it works perfectly. And it worked perfectly under F10.
I have been trying to figure this out for a long time now and can't seem to get it to work. I have three serial ports I need to communicate with. The first one works, but the other two, which have identical product and vendor IDs, do not. This is what I have so far under /etc/udev/rules.d/10-local.rules/
[Code]....
This is for the Linksys AE1000. This may work for other USB wireless network adapters, but I don't know for sure. Here is the original information ( Ubuntu's Forums ) about a very similar card. It clarifies that you need the 'rt3572sta', and some modifications are required to the source from ralink's website to include your Vendor and Product Id. Then modify a few files, and away you go. Step 1) Retrieve your Vendor and Product Id. Easiest way is doing 'sudo tail -f /var/log/messages' and then plugging in your USB device.
Code:
Apr 22 15:35:12 localhost kernel: usb 1-3: new high speed USB device using ehci_hcd and address 20
Apr 22 15:35:12 localhost kernel: usb 1-3: New USB device found, idVendor=13b1, idProduct=002f
Apr 22 15:35:12 localhost kernel: usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Apr 22 15:35:12 localhost kernel: usb 1-3: Product: Linksys AE1000
Apr 22 15:35:12 localhost kernel: usb 1-3: Manufacturer: Linksys
Apr 22 15:35:12 localhost kernel: usb 1-3: configuration #1 chosen from 1 choice
[Code]...
I need a way to find out what my dhcp vendor-class or vendor string is on a device. I want to take a client and based on the vendor string (if I can get what that string is) set up a pool for it.
View 1 Replies View RelatedDebian 2.6.32-5-amd64 KDE I have to make one of my computers wireless. i need some product recommendations for a wireless access point & a wireless network card.
View 4 Replies View RelatedI downloaded SUSE to a directory and copied that to a CD to use for running a trial on a 950 Mhz laptop. The CD does show a directory Boot and the boot directory does contain files. There is also a file named syslinux.cfg which when viewed from MS XP is identified as a configuration file for MS Office Outlook.
On boot attempts from the CD I get the Error message: No default or UI configuration directive found.Do I have an error on the D/L disk or is my proceedure not correct?
I am trying install rhel 6 on my rhel 5. I have downloaded rhel6.0-20100715.2-server-i386-dvd1.iso (from redhat ftp site) and burned into dvd. After rebooting I pressed F12 and chose cd installation.
I get the following message on my screen.
"ISOLINUX 3.86 2010-04-01 ETCO Copyright (C) 1994-2010 H.Peter Anvin et al
No DEFAULT or UI configuration directive found!
boot: "
I am using a linux FC-12 machine which is running on 2.6.36 kernel. I wanted to use the USB data card with that machine. But it is not detecting the device. I found that the modules usbserial, option, qcserial were missing. I installed them using "insmod".After that I have removed and reconnected the device. Still the OS is not detecting the device.After the reboot of the machine, again the modules related to USB are missing.
View 2 Replies View RelatedI purchased a new Desktop PC and MTS MBLAZE data card. It works in Windows XP OS. To make it work in Fedora GNOME OS how can I proceed? Which software do I need? Where do I get it and how to download and instal it in my PC? The firm selling the data card do not have an easy solution.
View 1 Replies View RelatedI am trying to install a PCIe card for data compression in Linux ubuntu 9.10(karmic Koala). As you can see in the following code although I have the root access I can not get permission to install the device driver.As I have the root access I suppose to get access to install the driver. I checked around and got the procedure from a web siteEnabling root access in unbuntuBasically in almost all linux machines we will be havingroot access for login.but in ubuntu by default that option was not enabled.If u want to have root login in ubuntu then u have to do some changes in ur Ubuntu machinesSteps to follow1.First enter into ubuntu as your user login.2.Then open the terminal and type the command sudo -s,it will ask for root access and type the password.3.Then type passwd root it will ask for new password4.Open terminal and go to the path /etc/gdm/5.Open gdm.conf6.search for AllowRoot=false7.and then change AllowRoot=true8.now restart ur machine9.now u can enjoy with root accessThe funny part is when I search for the file which is gdm.conf in the prescribed location, I can not find it.
Code:
root@faisal-desktop:/home/faisal/Desktop# cd AHA/
root@faisal-desktop:/home/faisal/Desktop/AHA# ls
[code]....
I have found two ways to get the main board product name: [sudo lshw][sudo dmidecode] Is it the nature of this info that's making it protected or is it the source code of these tools?Is there any way to get main board product name without sudo? Shall I dig inside the source code of these tools?
View 2 Replies View RelatedI have found two ways to get the main board product name:sudo lshw sudo dmidecode Is it the nature of this info that's making it protected or is it the source code of these tools? Is there any way to get main board product name without sudo?
View 5 Replies View RelatedIn playback application i guess "snd_pcm_lib_write1" is the function call used to write the audio data to sound card at kernel level.If that is true. how can i send the same audio data at kernel level to other system connected over LAN.
View 1 Replies View RelatedI am proposing moving from the mainframe to Linux. Problem is that I am not aware of a scheduling product that is available to handle the production code. Currently using CA7. Is there anything out there that accomplishes the same thing? As you can tell, I am NEW to Linux!
View 1 Replies View RelatedI have a Dell Vostro 3300, i5 460 processor with a NVIDIA 310M Graphics Card. I'm doing a KUBUNTU 10.10 (Maverick) install with the following results. The Live CD boots just fine to, "TEST," or "Install." Installation goes fine. However, the graphics card being used is the Intel i915. I have tried installing the NVIDIA drivers directly from the, "Additional Drivers," tool and after the reboot I get through the boot screen to the console. I try to manually startx and I get the errors, "no device found," "no screens found." The second install I tried purging and blacklisting the nouveau drivers and entering safe mode. Then using apt-get install nvidia-current. After that, nvidia-xconfig. Same results.
The third attempt I re-installed and this time downloaded the drivers from the Nvidia site (version 256.53). Blacklisted nouveau, remove all nvidia, updated initramfs, etc. The install went fine however I still end up at a console after boot with the same messages as above. No device found, no screens found. I've tried searching through the forum and web and have tried things like adding the modset option along with many other hacks, tips and fixes. still, no go.I can live with the Intel graphics for now although I lose 512MB of memory. Unfortunately there is no way to disable or change this set-up in the BIOS. I've seen quite a few bug reports at Launchpad:
1. Is this something I should just wait til a fix comes? Will a fix come?
2. Is there, or will there be an official Updated Ubuntu Guide for Maverick to install NVIDIA drivers with this tecnology?
3. Lastly, is there anything else I should try??
I'm having a problem installing Tor. I've installed it successfully a few times before thanks the excellent guide at: [URL] The error I'm having is when I request the gpg key:
Code:
ocean@ubuntu:~$ gpg --keyserver keys.gnupg.net --recv 886DDD89
gpg: requesting key 886DDD89 from hkp server keys.gnupg.net
Then after quite a delay all I get now (instead of "OK") is:
Code:
gpgkeys: HTTP fetch error 7: couldn't connect to host
gpg: no valid OpenPGP data found.
gpg: Total number processed: 0
I have been able to create the ISO, but I cannot boot due to the data dir not found error.
I have tried using "from=", different CD/DVD readers and different media to no avail.
I installed fedora on one of my three hard drives and it seems that something went wrong with the other two. Fedora recognizes the other drives but it seems the data on those drives is not there anymore. The below images are screen shots from my computer folder and disk utility program. I tried to look through Fedora documentation but I did not find a solution to my case.
View 14 Replies View RelatedI installed Ubuntu on my PS3. I got a confirmation message that Ubuntu was installed and I needed to restart. When I reboot I get a loading message and everything checks until:
Code:
ps3av_do_pkt: ps3av_send_cmd_pkt() failed (result=-11)
ps3av_do_pkt: failed old:10003 res:-11
EXT2-fs: ps3da1: couldn't mount because of unsupprted optional features (240).
EXT3-fs: ps3da1: couldn't mount because of unsupprted optional features (240).
EXT2-fs: ps3da1: couldn't mount because of unsupprted optional features (240).
mount: mounting non on /dev/pts failed
/init: /init: 923: KBoot loader
No default foot fs was found, or one was found and it didn't contain a message= config file.
[space between root and fs is how I see it]. If no rootfs was found, you can enter the shell here with 'sh'. Exiting will return you to this prompt. In the shell you can mount your rootfs as /mnt/root/.
Reasons this may have happened include:
-No drive with a rootfs was actually found
-Your footfs does not have the correct volume lable of "/"
-Your rootfs is corrupt (use rescue cd to fix this).
Ubuntu 10.04 server 64-bit I was following; The Perfect Server - Ubuntu Hardy Heron (Ubuntu 8.04 LTS Server) - Page 4 [URL] to set up the server on Ubuntu 10.04 and encountered problem on editing /etc/default/syslogd
[Code]....
I am trying to set the default files created by www-data to 774 (umask of 003).
I go to
Code:
/etc/apache2/envvars
and have set these parameters. NOTE: The only thing I actually changed was adding the umask 003 at the end.
Code:
# envvars - default environment variables for apache2ctl
# Since there is no sane way to get the parsed apache2 config in scripts, some
# settings are defined via environment variables and then used in apache2ctl,
# /etc/init.d/apache2, /etc/logrotate.d/apache2, etc.
[Code]....
Whwn I am sending mails , I used too get message like
Host found but no data record of requested type.
MTA: postfix
On my Linux (Debian/Ubuntu), I can get the PRODUCT of a library with "apt-file search" or "dpkg -S".May be I can get the VERSION by parsing the name of the library.so.But, How can I get the VENDOR ???
View 1 Replies View Relatedwhat is the vendor lock
View 9 Replies View RelatedI get the following error message when attempting to boot: No DEFAULT or UI configuration directive found.
View 1 Replies View RelatedI am trying to salvage the contents of my HD. I have tried to install Ubuntu from a CD (I created) and keep getting the error "No DEFAULT or UI configuration directive found!" My OS is Vista Home.
View 6 Replies View RelatedSo I decided to go on and install 10.04 LTS, because it is LTS... I created the live USB as directed on the Ubuntu download page. I download Universal USB Installer and it says USB created successfully. However, when I boot from the USB the error comes up as mentioned in title... The USB has no problems because I installed 10.10 last time from the very same USB. There's nothing wrong with the procedure because I am following the officially suggested method. Also, nothing wrong with partitions because one instance of Ubuntu is installed and was working fine until I tried to install video drivers (long story)...
View 9 Replies View RelatedHow to configure micromax 3g data card. I have redhat .
View 1 Replies View RelatedERROR: No configuration file found
No Default or UI configuration directive found!
boot:_
This appears when I try to boot Debian 7.6.0 from my USB drive