I need a way to find out what my dhcp vendor-class or vendor string is on a device. I want to take a client and based on the vendor string (if I can get what that string is) set up a pool for it.
View 1 RepliesOn my Linux (Debian/Ubuntu), I can get the PRODUCT of a library with "apt-file search" or "dpkg -S".May be I can get the VERSION by parsing the name of the library.so.But, How can I get the VENDOR ???
View 1 Replies View Relatedwhat is the vendor lock
View 9 Replies View RelatedHaving a problem with my Belkin wireless adapter when trying to stream music to my Pinnacle Soundbridge.The network connection is usually rock steady but drops anywhere between and few second and a few minutes after streaming music. Network manager still shows the connection to my home network as active but it is not. The connection comes back when I unplug the dongle and plug it back in. I found the following message repeated in the syslog
phy3 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3040 with error -110
Only thing I have noticed is that it refers to rt2x00 when I had thought it used the rt73usb driver.Had the PC and the Soundbridge for a number of years without any problems but I did recently have to reinstall Ubuntu from scratch. Currently running Ubuntu 10.10
i am using a alienware m17x QX9300 ATI 4870 CrossfireX 1920x1200p and till now was working fine with ultimate on it,now i don't know what happen ,before open the login screen is telling me that he has to start with low resolution,and after login sometimes is freezing.when i try to open display to set the resolution is giving me this: It appears that your graphics diver does not support the necessary extensions to use this tool. Do you want to use your graphics driver vendor's tool instead? and if i press yes is giving me this: There was a problem initializing Catalyst Control Center Linux Edition. It could be caused by the following. No ATI graphics driver is installed, oor the ATI driver is not functioning properly. Please install the ATI driver appropriate for you ATI hardware, or configuer using aticonfig Here's my /etc/X11/xorg.conf file - maybe there's some weirdness in it :
Section "Screen"
Identifier"Configured Screen Device"
Device"Configured Video Device"
SubSection "Display"
Modes "1920x1200"
Virtual1920 1200
EndSubSection
EndSection
Section "Device"
Identifier"Configured Video Device"
EndSection
I am new for Linux, my job is developing USB device on fedora Linux.The USB device driver has been completed successfully.my question is:how can I apply a new vendor Id (VID) for fedora kernel, so that my latest driver will be updated automatically when the Linux kernel was updated.
View 1 Replies View RelatedI am trying to build a jar file using a ant script provided by a vendor and while running the script, I am getting the below connection time out error when it tries to download a jar file.
Code:
C:ccuapi-java>ant run
Buildfile: build.xml
get_libs:
[get] Getting: http://download.java.net/maven/2/args4j/args4j/2.0.12/args4j-2.0.12.jar
[get] To: C:ccuapi-javaargs4j-2.0.12args4j-2.0.12.jar
[Code]...
I am running CentOS 5.6 on my servers (auto-updating to the latest patches). A couple of days ago, a number of updates were applied:
glibc-common-2.5-58.el5_6.4.x86_64
glibc-2.5-58.el5_6.4.x86_64
nscd-2.5-58.el5_6.4.x86_64
glibc-headers-2.5-58.el5_6.4.x86_64
[Code]...
This update broke a software tool from Xilinx (FPGA compiler). I rolled back all of the above, to 2.5-58.el5_6.3, and the tool works OK. I get:
/home/cad/xilinx/ISE13.1/ISE_DS/ISE/bin/lin64/unwrapped/map: symbol lookup error: /home/cad/xilinx/ISE13.1/ISE_DS/ISE/lib/lin64/libXst2_Core.so: undefined symbol: _ZN5boost7archive6detail17basic_oserializerD2Evmake[2]: *** [map] Error 127
I want to disable mounting usb storage devices except some devices based on its vendor id. I tried by adding below udev rule in debian wheezy
Code: Select allACTION=="add", SUBSYSTEMS=="usb", RUN+="/bin/sh -c 'for host in /sys/bus/usb/devices/usb*; do echo 0 > $host/authorized_default; done'"
ACTION=="add", ATTR{idVendor}=="054c", RUN+="/bin/sh -c 'echo 1 >/sys$DEVPATH/authorized'"
But it disabled all usb devices(USB keyboard and mouse). How can I allow other devices except storage devices.
This is for the Linksys AE1000. This may work for other USB wireless network adapters, but I don't know for sure. Here is the original information ( Ubuntu's Forums ) about a very similar card. It clarifies that you need the 'rt3572sta', and some modifications are required to the source from ralink's website to include your Vendor and Product Id. Then modify a few files, and away you go. Step 1) Retrieve your Vendor and Product Id. Easiest way is doing 'sudo tail -f /var/log/messages' and then plugging in your USB device.
Code:
Apr 22 15:35:12 localhost kernel: usb 1-3: new high speed USB device using ehci_hcd and address 20
Apr 22 15:35:12 localhost kernel: usb 1-3: New USB device found, idVendor=13b1, idProduct=002f
Apr 22 15:35:12 localhost kernel: usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Apr 22 15:35:12 localhost kernel: usb 1-3: Product: Linksys AE1000
Apr 22 15:35:12 localhost kernel: usb 1-3: Manufacturer: Linksys
Apr 22 15:35:12 localhost kernel: usb 1-3: configuration #1 chosen from 1 choice
[Code]...
I read a few threads about updating packages in opensuse 11.3, and about switching to a repository, but I still don't understand a few things. On earlier versions of opensuse I was used to set the repository priorities in an order that was convenient for me, and when I did an update, the vendor changed if needed.
Now, vendor change is not allowed by default, and I don't understand the right way to handle repositories, and updates. I found out that in Software Managment there is an option to allow vendor change, but I'm not sure that's the right way.
I'm really trying to get the Elgato Eye TV Diversity working with Ubuntu (I'm trying it on both Karmic and Hardy)
The problem is, lsusb shows the device but I don't get a vendor name, just an ID.
dmesg shows a usb device being detected, but not that it's a TV tuner.
I've followed the guides on these pages:url
url
url
url
P.S (I know some of the guides are for the hauppauge nova, but this is the same device as far as I can tell)
I used usb_modeswitch but the result was "No default vendor/product found." But usbmod_switch.conf file has all the vendor & product id contained in it. And modeprobe is also not effective. Even Sakis3g script fails to switch my datacard into modem. How to use BSNL Data Card in Fedora 13?
View 1 Replies View RelatedI am trying to install a vendor provided driver in Fedora 9 kernel 2.6.27.25-78.2.56.fc9.x86_64. Apparently the vendor stopped officially supporting Linux a number of years ago, so there were a few things I needed to change in the source code to get it to compile, now I'm trying to install it. Make runs successfully, but when I try to "make install" this happens:
Code:
# make install
Unloading any instances of foo module
Loading new foo into running kernel
insmod: error inserting 'foo.ko': -1 Operation not permitted
make: *** [install] Error 1
I've tried finding a solution via Google but it seems that the majority of people solved this problem using sudo, but I'm using su already and this still happens. I've also gone into make menuconfig and modules are enabled. I have access to the makefile and all the source code, so if something needs to be done there I can do it. If anyone has any ideas, please don't leave out any details; I'm a complete newbie when it comes to Linux
How can I determine full compliance:
Input data see below.
Code:
Code:
Code:
Result - ethernet devices about which I know the exact information :
Code:
I have been trying to figure this out for a long time now and can't seem to get it to work. I have three serial ports I need to communicate with. The first one works, but the other two, which have identical product and vendor IDs, do not. This is what I have so far under /etc/udev/rules.d/10-local.rules/
[Code]....
Since installing F11, my Canon LIDE 50 scanner refuses to work. xsane 0.996 produces an error message: Failed to start scanner: Error during device I/O.
sane-find-scanner says it is there: found USB scanner (vendor=0x04a9 [Canon], product=0x2213 [CanoScan], chip=GL841?) at libusb:001:006 But scanimage -L claims: No scanners were identified.except once when it admitted: device `genesys:libusb:001:006' is a Canon LiDE 35/40/50 flatbed scanner
I reluctantly tested the scanner on a Windoze machine and it works perfectly. And it worked perfectly under F10.
On the ia64 cluster (10 Xeon quad) I use in my job, (Cent OS): After some software upgrade by vendor, ethernet interface went wrong. On boot, message says MAC is different from expected ignoring.
ifconfig cannot see interface at all! (so that I cannot tell whether MAC in config script is correct). ifconfig eth0 hw ether 00:01:02:03:04:05:06 fails, saying no such a device. lshw is not equipped. lspci can detect interface.
As network interface is down, vendor cannot log onto the cluster. LED at lan cable connector is NOT on.
Is there any other way to know MAC? Is interface hardware down?
I am puzzled with trying to configure a linux (openSUSE) client to dhcp to eBox DHCP server. I am using dhclient to lease an IP address with dhclient eth0 -s 10.45.48.108 and get a response
openSUSE11232CL1 dhclient: DHCPDISCOVER on eth0 to 10.45.48.108 port 67 interval 4
openSUSE11232CL1 dhclient: DHCPOFFER from 10.45.48.108
openSUSE11232CL1 dhclient: DHCPREQUEST on eth0 to 10.45.48.108 port 67
openSUSE11232CL1 dhclient: send_packet: Network is unreachable
openSUSE11232CL1 dhclient: send_packet: please consult README file regarding broadcast address.
The server reports eBox141 dhcpd: DHCPDISCOVER from 00:0c:29:3e:57:a3 (openSUSE11232CL1.domain.net) via eth0
eBox141 dhcpd: DHCPOFFER on 10.45.200.2 to 00:0c:29:3e:57:a3 (openSUSE11232CL1.domain.net) via eth0
I interpret this as the server receives the request and the client accepting it but the lease does not last long and the connection breaks. what this could be and why the connection breaks? Or my undestanding is totally wrong on how it works and should work? And BTW, where is that README file that's referenced in the message I receive on the client?
We have a large number of devices on our LAN with the mac prefix of 00:60:60. We want to assign these addresses from a separate address pool. I've created two classes, one to match 00:60:60 and another that I want to contain any other device. When i try to start the server I get:
/etc/dhcp3/dhcpd.conf line 33: boolean expression expected
match if not binary-to-ascii(16,8,":",substring(hardware, 1, 3))
^#this carrot should be under the last parenthesis#
Configuration file errors encountered -- exiting
Here is the relevant section of /etc/dhcp3/dhcpd.conf
class "006060" {
match if binary-to-ascii(16,8,":",substring(hardware, 1, 3)) = "00:60:60";
}
[Code].....
I've tried a few variations on that line. I've spent days trying to find any examples of "match if not" and haven't found anything. I assume it's going to be something to do with parenthesis/quote placement. Oh and this is ISC DHCP Server V3.0.4.
How can I implement c_str() for a string class?
View 2 Replies View RelatedI am contemplating the use of DHCP options as a way of passing host-specific information to hosts that are booting disklessly from a network server. My intention is to have the DHCP client request certain options, and use the reply to configure the diskless hosts accordingly. The theory and rules behind all of this seem well documented on web sites such as die.net. However, the practical application of the protocol seems to be a lot less clear. What I am looking for is an explanation of what (existing, I hope) tool(s) are used, and how they are applied so that I can grab information from the DHCP server, and use it in userspace scripts or other programs. Specifically, my intention is to use a locally defined option that would give a host-specific directory name or filesystem to use by the diskless host to obtain host-specific applications and configuration data.
So far, all of the DHCP client documentation I've found relates to the usual function of assigning IPs, etc. I've looked at dhclient-script on a Redhat system and can't figure out the relationship between it and the dhclient program. Clearly, the script is invoked somehow by dhclient, but I don't understand where the transfer of data received from the server gets into the script. Does dhclient just create a list of exported environment variables the child script then gets access too? What are the rules for how variables are created and what variables are created?
I have an embedded device for which I've created an html configuration page. This page allows you to set static IPs, dhcp, and can scan for wireless devices.My problem is that in order to access the device it requires that it runs as a dhcp server otherwise people are not assigned an IP and so can not access the embedded devices static IP. (This config page is for the laymen and so they are not the type who are able to set up their own static IPs). One of the potential options is to have the device connect to the network on eth0 acting as a dhcp client. However this prevents me from running a dhcp server.One solution I can think of is running a dhcp server only if it doesn't detect another dhcp server running on the network.
View 4 Replies View RelatedI want to use dhcpcd instead of dhclient on Ubuntu. The 'interfaces' man page say: "The dhcp Method This method may be used to obtain an address via DHCP with any of the tools: dhclient, pump, udhcpc, dhcpcd. (They have been listed in their order of precedence.)"
I can't find where to change this default order. I can uninstall dhcp3-client, but this will also remove ubuntu-minimal, which is not a good solution.
I would like to use dhcpcd instead of dhclient in my Debian installation, because I had some trouble with dhclient in the past and I assume the problem is still exists now with some equipments.
So I would like to use dhcpcd, but I couldn't find a way to tell the system to give higher priority to dhcpcd than dhclient.
Also, I've tried to remove the package 'isc-dhcp-client', but it also would like to remove the following packages: isc-dhcp-client knm-runtime network-manager network-manager-kde
Moreover, it says no need the following packages anymore: usb-modeswitch dnsmasq-base libnm-util1 usb-modeswitch-data network-manager-ppp pptp-linux network-manager-openvpn libnm-glib-vpn1 libnm-glib2 modemmanager vpnc network-manager-vpnc
I would like to still be able to use kde-network-manager, because it is much easier to manage wifi connections using this interface.
Is there any way to get an async notification (perhaps through something like a Linux message queue or Unix socket) when a DHCP client is either unable to renew its lease, or the address obtained changes from the previous value? I've got the ISC client and will dig into it to determine if it supports such a feature, but thought I'd ask here in parallel. (I'm trying to find out if there are any DHCP clients out there which already support this capability.)
If you're curious: We have an application where we're doing auto-registration of an IP camera to an external server. If the camera's dynamically assigned address changes, we need to restart the auto-reg state machine. I've seen implementations where a socket is opened and a SIOCGIFADDR ioctl used to fetch the IP addr, but I'd sure like to avoid polling like this if possible.
I have Centos 5 installed on a PC in the local network. I have installed the RPM dhcpv6-client-1.0.10-16.el5.i386.rpm on this PC to configure it as DHCP V6 client. The RPM was installed successfully, and I have done modifications to the following files:
1. /etc/sysconfig/network, set the networking to yes.
2. /etc/sysconfig/network-scripts/ifcfg-eth1 set the BOOTPROTO=DHCP.
Now the problem is when I start the client on this pc as dhclient, it throws the following errors, and logs out after some time. All the network configurations were lost and the PC gets disconnected from the network.
[root@ServerB]# dhclient
Internet Systems Consortium DHCP Client V3.0.5-RedHat
Copyright 2004-2006 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/
[Code]...
I have a Lan with 100 computers with microsoft windows xp and vista on it, and I need to build a CentOS Primary domain control- PDC. So I am building a PDC , with samba 3.x +Ldap ( Light Directory Acess Protocol), with static eth0 and DHCP-server( Dynamic Host Control Protocol) on eth1.
Eth0 : 192.168.1.3
Eth1 : 192.168.1.5
Here is the configurations files:
== BEGIN uname -rmi ==
2.6.18-194.17.4.el5 x86_64 x86_64
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
centos-release-5-5.el5.centos
== END rpm -q centos-release ==
== BEGIN cat /etc/redhat-release ==
CentOS release 5.5 (Final)
== END cat /etc/redhat-release ==
== BEGIN getenforce ==
Permissive
== END getenforce ==
== BEGIN rpm -q yum rpm python ==
yum-3.2.22-26.el5.centos
rpm-4.4.2.3-20.el5_5.1
python-2.4.3-27.el5
== END rpm -q yum rpm python ==
== BEGIN ifconfig -a == .....
I have an embedded device for which I've created an html configuration page. This page allows you to set static IPs, dhcp, and can scan for wireless devices. My problem is that in order to access the device it requires that it runs as a dhcp server otherwise people are not assigned an IP and so can not access the embedded devices static IP. (This config page is for the laymen and so they are not the type who are able to set up their own static IPs). One of the potential options is to have the device connect to the network on eth0 acting as a dhcp client. However this prevents me from running a dhcp server. One solution I can think of is running a dhcp server only if it doesn't detect another dhcp server running on the network. However I have no idea how this could be setup.
View 2 Replies View Relatedi hav configure dhcp server. but the ip is not getting assigned to my client machine.
View 3 Replies View Related