I went through the howto's regarding this pot but was not clear which package should I install.
1. Broadcom BCM43
2. Broadcom BCM43xx
3. Broadcom BCM 43legacy
3. BCM linux STA
I have installed F11 on my Dell Inspiron 1501. I tried to get the Broadcom 4311 wireless card to work by following the instructions for installing the Broadcom driver from this link: [url].
That resulted in the following errors when I gave the command:
Code:
I removed the broadcom-wl package and installed the autoen package from DangerMouse. After rebooting wireless works but I still get the same errors when I give the command:
Code:
I had to disable encryption on the router to connect, but I guess that's a compromise I'll have to make right now. I will work on that some more after I get these error messages straightened out:
Code:
Note that wireless does seem to be working (though without encryption) despite the error messages. And I got these same error messages with the Broadcom driver but I could not get wireless working.
I am having a little trouble connecting to my wireless network. Running Fedora 10 32 bit.I'm trying to connect to a hidden wireless network. I updated the firmware for my driver but apparantly the driver is still not working. Broadcom has a driver from their website for Linux 32 bit systems. Should I attempt to install it? I read a post where the driver is built into the system kernel. If so I would need to blacklist the one of the drivers. Correct?
[justin@justin ~]$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wmaster0 Interface doesn't support scanning.
code....
I'm having a strange problem with my wireless card (I never had troubles with it so I'd be glad if you could help me in making it work again). I have installed the restricted STA driver for my Broadcom BCM4311 wireless card, and apparently the card is recognized, and in fact I can "see" the available wireless networks and connect to my one.
The strange things is that even if I connect to my network I can't navigate. If I link an ethernet cable, start navigating and after disconnect the ethernet and keep using only the wireless, I can navigate without problems.
I installed Ubuntu 11.04 on my mom's Inspiron 1521 and before I had it on there I had a older version of ubuntu which worked fine and could connect to the Internet, but since my mother isn't that well educated in computers and wants a simple to use UI, Ubuntu came into mind.
Well after installing ubuntu for a hour or two and trying to configure the drivers to allow Internet access with out a USB adapter using the BCM4311 I tried everything such as following the pretty basic tutorials online on installing the drivers with no luck. I check the additional drivers application and it's telling me the drivers are installed properly and are okay. ... Well, why am I not able to find a list of wifi connections yet?
I did the update command and updated every package on the machine. I reinstalled the kernal drivers for the BCM4311. I even installed the installer for the kernal device and nothing seems to be working.
I have this weird issue which only appears when I am using 64 bit Ubuntu. Every now and then my laptop seems to go into a kernel panic (system unresponsive, numlock and scrollock lights flash repetitively) only when I am using the broadcom wireless. I can connect to my wireless router and use the internet and local network, but eventually, kablamo, crash, bang, boom. The only way out of the crash is to power off completely. After repowering, the wireless network is fine until the next crash. There does not seem to be a pattern or time period to cause this crash either. I have purged network manager(which I couldn't get to use my wireless) and am using wicd, which allows me to connect wirelessly.
Here is the details of my system:
Dell inspiron 1520
lspci (snipped)
0c:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)
[code]....
I have Lenovo Notebook 3000 N100 with built in wireless - Broadcom BCM4311 802.11b/g. The seems to be properly installed(as per the screen shots) but still I can not see any wireless networks. I checked out most of the forum but could not find any exactly matching situation. find the attached results of the below command which might give you idea : sudo lshw -C network
As per one of the screen shot it seems that "This drive is activated and currently in use" still I can not see any routers(including mine) which I can connect. Also the Wifi LED is not glowing.
I just installed the 64-bit Kubuntu 11.04 and i've been having some issues getting the wifi to work. At first I went to additional drivers and activated the STA driver and restarted. After restarting when I went into the network manager and any option for wireless was disabled.
[Code]....
Yet another Linux newbie with wireless problems I'm afraid. I saw some postings that appear very similar but I don't have any Linux experience and don'h to make uncontrolled changes to the environment without expert advice.Background: I have an old laptop (HP Pavilion dv9000) with Vista installed and a troubled history (overheating motherboard failure), so I put it on the shelf and replaced it with a new Windows 7 laptop (Dell Studio 1555). But I have been intrigued by the Ubuntu reviews and thought I would dig out the old laptop and install Kubuntu 11.04 (replacing the 2 Vista partitions with a single Kubuntu partition).
Kubuntu installation was easy and I am impressed by the Kubuntu interface, but I soon noticed that it was not detecting my wireless router, which works fine for everything else (Dell, Sony Bravia TV and also an internet radio). The wired connection is okay (using it now) so I guessed the problem was Kubuntu notognising the Broadcom BCM4311.The network interface tool shows the wired connection but the Wireless tab is greyed out.I also installed Wicd Network Manager but that just confirmed what I knew.I noticed other threads have asked for the lspci and lsusb details so here they are:
lspci
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
[code]...
I think I've read every post here about the Broadcom and connection.I thought I tried everything.Turns out (read Chapter�35.�Using NetworkManager) using Connection Manager (K Network Manager) you can not use, what I wanted to use, 'all users, use connection' or said another way, the wifi would be activated and connected Before the user 'logs in'. Well, as I said, it turns out that if you are using gnome, this will work with NetMgr, but NOT in KDE. If you want to use 'system connect' then you have to use 'traditional' if in YaST2. Oh well, at least 'i'm' connected.... (i'm the only user, so not a big deal right now, but would like to get it working...)
View 2 Replies View RelatedI have a Hewlett-Packard HP Pavilion dv6000. I had no issues before the upgrade, but after, my wireless driver refuses to turn on the wireless at all. I've seen in most of the posts, people can see the wireless networks but not access them. I can't even get my little orange wireless (off) light to turn blue (on). The "additional drivers" option in "administration" was a bust and I've tried reinstalling the kernel from my original disk iso.
Here is my wireless info:
Code:
03:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
I currently have the STA broadcom driver enabled and all I can do is use a cable for internet right now.
I was told by an experienced Linux user/IT professional that older Broadcom wireless cards had embedded code preventing access through non-Windows OS's. I was told that there were drivers that were basically "hacks" for skirting this issue. I've tried two different drivers and neither seems to be doing the trick. My current driver is the "Broadcom STA wireless driver".
Symptoms
Recognizes my network and others
Says it's connected
Won't load any web pages
Frequently asks for authentication
I've authenticated using my network password and my router's security key
Here's what the terminal says about my wireless card:
05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
Subsystem: AMBIT Microsystem Corp. Device [1468:0422]
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at d0000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: wl
Kernel modules: wl, ssb
I'm trying to install ndiswrapper in Fedora 10, but the package is not found:
[Code]...
After reading and trying tons of tutorials and several OS reinstalls, I'm stuck trying to load wireless on my Dell Vostro 1400 laptop. Before you say search forums! I hurry to tell I did. No solution seems to work. WLAN chipset - Broadcom's BCM4311 / BCM 2050. 1st scenario - native CentOS 5.3 drivers Although CentOS recognize WLAN card and displays it's name correctly, neither network or NetworkManager sees any of wireless networks.
2nd scenario - Broadcom's drivers Most know Broadcom has released Linux drivers. I had some more luck with them than in 1st scenario although problems occur. After successfully compiling Kernel module, wireless networks are discovered and can be successfully connected but no pages load. It seems like DNS is not resolving at all and page loading timeouts instantly. Tested on TKIP-encrypted network.
Sometimes i have on some magazines or Internet Zip packages that are the answer of what i am looking for.
Wich tool and how can i do it? c Well, i am in position to say that i had downloaded from Internet or located the package in the Cd or DVD that comes with the magazine.
But now comes the big question. How can i put this package ( install) on my distro ???
Do i have to be a normal user or should it be root or su (superuser) ?
The packages that come with the distro is easy, because i select them and everything is done
As i told before, maybe this is a silly question, but i simple don't know how to install them and i need some of them to leave MS for good.
Fedora 12 64bit. Is there an easy and reliable way to install *.tar.gz package after extraction? Instead of going through ./configure etc.
View 6 Replies View RelatedI'm happily using OpenSuse 11.2/KDE on my laptop equipped with a Broadcom BCM4311 WLAN chip, but today, after a restart, WLAN ceased to work. I mean that Network Connection doesn't show anymore available WLANs. Two things that seem strange to me are that the
[Code]...
Today I was using Gchempaint (part of Gnome Chemistry Tools) and found that the F12 version fails miserably to correctly export H to xyz. So I decided to install the latest version I found (0.11). There are, however, some problems I must sort out during compilation.
Apparently it does not see my 'cairo' installation and so I get the following error message:
Code:
checking for cairo... configure: error: Package requirements (cairo >= 1.6.0) were not met: No package 'cairo' found
Consider adjusting the PKG_CONFIG_PATH environment variable if you installed software in a non-standard prefix.Alternatively, you may set the environment variables cairo_CFLAGS and cairo_LIBS to avoid the need to call pkg-config. See the pkg-config man page for more details.
Ubuntu's team put an alpha unstable version by default into the fresh install of Ubuntu... and... where's firefox 3.6 package now?
View 4 Replies View RelatedI've just installed Lucid Lynx and it seems to be running fine, except the synaptic package manager is downloading things incredibly slowly. Is this just because the server is busy due to the new release?
View 4 Replies View RelatedI found a post here somewhere detailing the steps to make wpa supplicant work with EAP-FAST, however the steps appear to be old.
I was able to patch openssl using the openssl-tls patch supplied with wpa supplicant package, however when I try to rebuild the package for install, it fails quite horribly.
is there a known good set of instructions for 10.4 and how to get eap-fast working using an anonymous supplied PAC?
I'd really like to convert my HP laptop over to ubuntu, but unless I can get my corporate wireless functioning, I won't be able to.
I need to install the following dependencies for synspam on Ubuntu 9.10 karmic server:
Code:
sudo aptitude install nfqueue-bindings-perl libsys-syslog-perl libappconfig-perl libnetpacket-perl libnetaddr-ip-perl
dpkg -i synspam_version_all.deb
Of these, only libnetpacket-perl is not packaged for Ubuntu 9.10 karmic.
Is this functionality present in another 9.10 package with a different name? 10.04 Lucid does have the package: [URL]
I did a full install of 9.10 on my Dell Inspirion 1200 laptop & use a Dell 1350 card, after several posts and replies I went to [URL]and followed the instructions for Ubuntu/Debian. This is the result I get....
mike@mike-laptop:~$ sudo apt-get install b43-fwcutter
[sudo] password for mike:
Reading package lists... Done
Building dependency tree
[code]....
I followed this procedure before installation (live CD) and it successfully found and installed the firmware. Apparently it was saved in live CD. What do I need to do?
Debian linux:
I've tried apt-get install with the following packages:
And others and always get 'Couldn't find package'.
I tried doing an apt-get update and that worked without problem.
I am trying to establish a tunnel from my ubuntu machine 9.10 using miredo package. After installation I wanted to ping an ipv6 address and I get this error:
Address unreachable, destination unreachable
However, when I ping ipv6.google.com I have no problem.
Still I am asked to package a war file as an RPM package. That is an unusual RPM packaging(To me). If you guys could guide me I have a war file inside a folder, that folder is inside a tar file as a SOURCE for RPM package. The structure is like below.
[Code]...
I simply want that the war file from sources is transferred to the web app of my tomcat server through RPM. I try to package it as an RPM, but its always giving me errors in %build stage. When I try to remove %build from stage from the spec file, then it says command missing.
My system details are:
SUSE Linux Enterprise Server 10 (x86_64)
VERSION = 10
PATCHLEVEL = 1
LSB_VERSION="core-2.0-noarch:core-3.0-noarch:core-2.0-x86_64:core-3.0-x86_64"
when I try to install a package, I've the message The following packages have unmet dependencies:package-xy: Depends:lib-something (>= version_number) which is a virtual package.
View 14 Replies View RelatedI am following this guide to installing eclipse via terminal command-line on Linux. However, this seems to be happening lately with all the packages I try to install..I checked the Synaptic Package Manager and reloaded and rebooted the computer, but to no avail.
View 5 Replies View RelatedI have a problem when installing this package through synaptic package manager. this is :
libpng12-dev
the error is:
W: Failed to fetch http://security.ubuntu.com/ubuntu/po...tu2.1_i386.deb
404 Not Found [IP: 91.189.92.167 80]
my distribution is ubuntu 10.4.
Is there anyway to show package size that comes up in the search so you don't have to apt-get install package individually and wait for the installation initiation and then reject to install after it gives u the [y/N] confirmation thing?
View 2 Replies View Related