My intel pro wireless 2200 NIC doesn't work anymore. Yesterday it did, but not today (I didn't do anything special, so that it could go wrong).What is ucode and -62? Any ideas? I already checked the forums and found that ipw doesn't work when ndiswrapper is loaded. Well, I don't have it loaded. What happend?
View 8 RepliesWireless networking doesn't seem to work. When I try to create a new network interface with system-config-network, my wireless card doesn't show up. The following comes from dmesg:
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: ipw2200-bss.fw request_firmware failed: Reason -2
[Code]...
I saw a post about this elsewhere and downloaded some firmware drives from [URL] and installed then. But, I'm really out of my league when it comes to this kind of stuff.
I recently installed Fedora 15 x86_64 on my new AMD Machine and I'm quite pleased with things thus far.Here's where my problem comes. I mainly bought that machine to help me with Development. More specifically, Virtual Machines for testing purposes. I have installed Fedora 15 x86_64 as a qemu-kvm Virtual Machine and it's working.. for the most part. I am having a whole lot of trouble getting it to connect to the Internet.
My guess is the only way I'm going to reliably do that is to setup a Bridge. Yes/no? However, in order to setup a Bridge I need to disable NetworkManager and that where the fun happens. It completely disables my network connection. I'm probably missing something small, but I can't figure out what I'm missing. I've double checked my ifcfg-em1 multiple times(I've been trying for ~24 hours so far) and all the settings are as they should be.
I've turned NetworkManager off and stopped it(chkconfig and service) and turned network on(chkconfig and service). Theoretically I should simply need to turn off NM and turn on network and things should be fine. no?
Well, aside from adding:
ONBOOT=yes
NM_CONTROLED=no
to ifcfg-em1.
I updated my system yesterday (Ubuntu 10.10). Few minutes later there was a notification that said something about a program that stop working. Since then I cant connect to the internet anymore. I can see all the wireless networks around me but when I attempt to connect to my home network it keeps asking me for the password. i didn't install anything before or after the updates. I am sure there was something on the updates that screwed my system.
View 1 Replies View RelatedI can't get my card Intel Wireless 5300 AGN to work. I'm running Slackware 13.1 and it's a full, fresh install.I get to show up with lspci -v:Network controller: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection...But it will not show up with 'ifconfig' which will only list the local loopback (yes we have have a eth problem as well but one thing at a time).
View 5 Replies View RelatedI'm using this card on a Toshiba Tecra M3 laptop. Firmware is installed. iwconfig shows the following:
Code:
eth1 radio off ESSID:off/any
Mode:Managed Channel:0 Access Point: Not-Associated
[code]...
Intel 5100 wireless card doesn't connect on 10.04?
View 1 Replies View RelatedI upgraded to OpenSuse 11.2 and just about the only thing that doesn't work is my wireless internet. From my research, I should be using the iwl4965 or iwlwifi driver; however my system seems to be running iwlagn. I have no idea how to switch it as neither of the correct drivers can be found in my yast, and I've failed to find any information about this on the IntelŪ Wireless WiFi Link drivers for Linux* website.
View 9 Replies View RelatedI just installed Fedora 15 yesterday and can't get wi-fi to work. When I click 'on' on the Wireless label, it goes back to 'off' immediately. When I open the Network Settings menu and disable Airplane mode, the Wireless connection goes on and then off immediately. I took a look at /var/log/messages and it shows this:
[Code].....
Recently I have installed Fedora 14 on my other laptop. It's a dual boot with Windows 7. Everything worked perfectly fine, networking included, until my friend didn't accidently turned off the wireless by pressing a wireless button on the laptop. Since then the wireless on Fedora doesn't work. It does on Windows thought. I've tried restarting the laptop few times, but the wireless still doesn't want to work again.
View 2 Replies View RelatedI have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:
[code]...
i'd like to extend that ma intel wifi link 5100 is not detected no more after perform upgrade package( upgrade the kernel too ). when im using command 'lshw -C network' , there is appear to be detected, but not on command 'iwconfig' or even 'ifconfig' it just show nothin. also network-manager no longer show that ma wireless is work properly anymore.
the old kernel : 2.6.25-22 ( my wireless detected and usable )
the new kernel : 2.6.25-23 ( my wireless detected and unusable )
have You noticed that mt command doesnīt work anymore on 11.4? We try to install new version to hadle robotic library, but someone has written mt command as a new, and it doesnīt accept mt -f command anymore. cpio based mt command itīs not reliable as old one. Can anyone tell where to get old mt command which is compatrible new 11.4 x64 bit version?
View 9 Replies View RelatedI'm using Karmic since November and standby/sleep has always worked fine. Some weeks ago, it stopped working fine.
After a reboot, I can put the system in standby only once. If I try standby after that, the system seems to do a normal standby, but it resumes at the moment the fans would normally stop working.
I tried different things like the s2ram program, pmi action sleep, etc. I went to the BIOS and tried a number of things, one was succesfull: disable USB. When USB is disabled I can go into standby every time. When I enable USB again (even with no devices connected), standby only works once again.
So, how can I disable USB at the moment I go into standby?
If i use my Ubuntu some times per week, there isn't any problem. But if i don't use it for a short time (a week), when i want use it again and select it on GRUB.. after the first loading screen (on Ubuntu 10.04 the purple screen with Ubuntu in white and some points under), my screen is black. The computer screen is receiving signal because the led is green and not brown/orange like when is on standby mode. On Windows i haven't any problem.
First time it happened with Ubuntu 9.10. I didn't got solution for it and i format the partition and install the 10.04. But now it happen again with 10.04. I have an ATI 5770 and i have tried drivers since 9.12 till 10.4 (last ones the best i have had) On versions before 9.10 i had no problem, but i can't confirm that, because i had other graphic card (NVIDIA 9800GT). But the 5770 didn't work well on previous version so i updated to 9.10 and after this problem, updated to 10.04.
At spanish forum, people don't know solution for this problem, they never read about a similar problem. I hope you know a solution for it, because the only one i found and work is.. format and reinstall.
I've been using fedora for about 2 years, and i recently bought a new laptop. After using a usb mouse my toughpad no longer works? Now it works on login but after login touchpad input is gone.
View 4 Replies View RelatedI just upgraded from kde 4.4.4 to 4.6.0 in the *stable* kde repo, and now beclock effect doesn't works anymore I can't live without it how can I solve???
View 2 Replies View RelatedAfter installing openSUSE 11.2 to get rid of my suddenly dysfunctional 11.1, my Audigy 2 doesn't produce a single sound anymore - neither via the regular nor the digital output. It used to work like a charm on 11.1. I cannot say how much I have come to hate Linux during the past 12 months after constant problems with system instabilities due to incompatible software component updates and stuff like my system still not working after ominously going out of service and "repairing" it with openSUSE's repair function.
I decided to get into Linux because I found it cool when I started with a couple of years abo and thought it would be well worth getting into an OS that might become the successor of Windows. I also wanted an OS I felt secure with when doing online banking or shopping.
Well, I have to say that Windows 7 delivers on all the promises Linux has made (at least those that are important for me), and that Linux hasn't advanced a micrometer in the time I have started using it. The only thing in favor of Linux was that it worked well enough on my 6 year old hardware. I'd rather purchase some new hardware and Windows 7 on top of than tormenting myself more with this unspeakable PITA Linux has proven to me to be. To hell with it. Stay in your server corner, but stop telling people Linux was anywhere close to being a useful desktop operating system. PS: Yes, I have tried other distros too.
I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf andOutput of lspci for the audio device:
00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1)
Subsystem: Giga-byte Technology Device a002
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
[code]....
Update 6th March 2010: Update to Kernel 2.6.31-20 SOLVED the problem. Recording works again (still wouldn't in kernels 2.6.31-17 to 2.6.31-19). If a kernel update doesn't solve your problem, please read post 14 on page 2 by Mocha which seems to have solved the problem for other users without updating the kernel
Update 8th February 2010 to Kernel 2.6.31-19 did not solve the problem, please also read post number 7 for more details.
Quick Conclusion for other users who might experience the same problem:
After an update to kernel version 2.6.31-17 in Ubuntu 9.10 Karmic Koala, my external microphone did not work anymore. Playback was possible, just recording would not work anymore, although there was quite some background noise in the headphones. This made it impossible for me to use Skype and/or Sound Recorder.
All the possible solutions offered below did not help in my case (although you might give them a try).
I switched back to kernel version 2.6.31-16 where the problem does not occur.
Output: cat /proc/asound/card0/codec#* | grep Codec
Realtek ALC662 rev1
I know there are lots of threads about this topic, but I have spent hours on this problem already and none of the solutions offered so far worked for me so I decided to start this thread.
I have been using Ubuntu 9.10 and so far, my external microphone worked flawlessly in Skype as well as in Sound Recorder. A few days ago, I received a call on Skype and all the guy on the other side could hear was loud noise. I can only play sound, but not record anymore (i.e. the microphone doesn't work anymore). I tried two different microphones just to be sure whether one was defective and also checked it in Windows (where they both work).
I am not sure what might have caused this problem, I just remember a kernel upgrade about that time (not sure whether this is the reason though). I use 2.6.31-17-generic now.
Here is what I have tried so far:
1) Right-click on the Sound Icon in the top right corner and checked the following: in the hardware tab, it is set to analog stereo duplex, input is set to internal audio analog stereo (no other choice here) and the mic is NOT muted (playing with the volume doesn't help either) and output is set to internal audio analog stereo (again, no other choice) and connector is set to analog output (here I can switch to analog headphones or analog speaker, but makes no difference).
I remember that I could choose between Microphone 1 and Microphone 2 in the input tab; this is somehow magically gone.
2) Installed padevchooser, tried several settings to no avail
3) When I use "alsamixer" (version 1.0.20) in a terminal, Playback>Master is set to 100<>100, Capture is set to 150<>150, lowering and/or playing with these figures doesn't help either.
When I use "alsamixer -Dhw:0" in a terminal, I get the same results as in step four.
4) In Gnome Alsa Mixer, only "Beep" is muted, everything else is set to max. I have Master, Headphon, PCM, Front, Front Mi (x2), Lin, Mic, Mic Boost, Capture (x2, set to record), Beep, Speaker
I have tried to mute/unmute different setting to no avail. Now I wonder why I have two Front Mi and two Capture entries. This is different than it used to be, might this be causing the problem?
5) Fiddling with Pulse Audio Volume Control didn't help either.
6) Had a look at "paman" (pulse audio manager), not sure whether I should change anything here.
7) Installed "linux-backports-modules-alsa-karmic-generic" and rebooted as recommended in several threads, did not help either.
Added the parameters "model=auto" and "probe_mask=1" to '/etc/modprobe.d/alsa-base.conf', did not work, so I deleted the entries again (hint from [url], see post 5)
Now I am at my wits end. I need my microphone to work, especially for Skype, otherwise I have to switch to Windows every time I receive or want to make a call which is definitely not a long-term solution?
Does anybody have an idea what might be causing this problem? As I said, it used to work flawlessly just a few days ago and now I don't even know what I should do next to make it work again...
Output of "amixer"
When I run "alsactl init" I get the following result which might be at least a part of the problem, but I wouldn't know how to solve this problem:
Unknown hardware: "HDA-Intel" "Realtek ALC662 rev1" "HDA:10ec0662,103c303a,00100101" "0x103c" "0x303a"
Hardware is initialized using a guess method
I don't know whether it has to do with Googles revamp of their search page or something else but it doesn't work any more.
Typing:2+2 =
Results in:"Google Calculator could not evaluate the expression."
I'm using Ubuntu 10.04. GNOME Do 0.8.3.1
I've got a double boot system (Windows XP Pro and Ubuntu Maverick). Since I updated Grub2, Grub doesn't work anymore! I'd tried this (because I HAD that error). But since than, I'd a black screen (harddisk didn't anything, and Grub too...) And now, after using a couple of these commands via the Ubuntu Lucid Lynx Live CD I get a mini bash in Grub, but no entry's to one of the two systems! What's wrong, and what do I have to do? (and what did I wrong?
View 7 Replies View RelatedI recently installed vsftpd on my system and it was running fine for my system users. Now I wanted to add virtual users so I googled it, I found this tutorial: [URL]
I did what they've been saying over there but when I restarted the vsftpd I couldn't login with the virtual user and also not with the system user anymore. This is the error ( with the system user who could login before ):
Code:
Status:Verbinden met 109.230.234.21:21...
Status:Verbinding aangemaakt, welkomstbericht afwachten...
Antwoord:220 (vsFTPd 2.2.2)
[Code]...
after installing trying to install veetle on my ubuntu 10.04 64 bit I always get the message at the start-up:could not update /home/user/.ICEauthority.my sound control does not work anymore (message: 'waiting for sound system to respond')using Krusader I get the message 'Cannot talk to klauncher: The name org.kde. klauncher was not provided by any .service files.I checked the owner of .ICEauthority and the permission and they are OK. Same for my /home. None of the suggestions found in the other threads worked.Veetle has been installed using the install.sh script and there is no unistall option
View 3 Replies View Relatedmy touchpad worked out of the Box after insalling Xubunut 11.04 and did so ever since. But since yesterday it doesn't. It worked when i shut down the laptop and didn't when i booted later. How do i fix this? Yes i read the article about thouchpads.
View 2 Replies View RelatedI am using Ubuntu 10.04LTS and receive regular software updates. Being a silver-surfer I frequent an old fogies site called "Beyond the realms of AOL - forumotion.net" where we share memories and the like. The site (message board) has a rolling menu which up until recently worked on my computer ... now it doesn't! When I log-in, the rolling menu pops up for a second and then disappears. I get the feeling that one of the regular upgrades has removed a plugin or something from my system. I have Adobe Flash 10 (latest version) installed ... perhaps I'm missing something!It has to be my system because the rolling menu works perfectly well using Windows XP.
View 7 Replies View RelatedI've just noticed my Dolphin compress service menu doesn't compress anything except for '*.zip'. It used to compress '*.tar.gz' and '*tar.bz2' but now none of these work, and the bz2 option is gone altogether.Does anyone know what might have happened?I have openSUSE 11.3 & KDE 4.6, but this happened before I upgraded to KDE4.6 just a few days ago, so it's not KDE4.6 related, maybe 4.5? maybe Dolphin?I also tried to install the extract/compress plugin but it says "Could not find program 'compress_TARBZ2.sh'" which all are in my /bin folder. I also checked I have all the extract/compress file installed: zip, tar, gzip, bzip and so on.I also tried 'Compress to...' which open Ark, then I selected either 'gz' or 'bz' and still nothing happened.
View 9 Replies View RelatedAfter the last updates (in which there was also the 2.6.35.28 kernel) my audio isn't working anymore. When i open an audio file, it goes foreward with steps like 5 secondos and i can't listen nothing. Videos i can see, but with no audio, and ..... videos go at like 2x speed (and also here no audio). I tried booting with the 2.6.35.27 kernel, but doesn't change anything.
View 1 Replies View RelatedI'm running Ubuntu 10.04 on my laptop. Up until about a week ago, my wireless worked fine, but now it rarely connects. Sometimes the connection indicator shows that I am connected, but when I click on it it doesn't show any active networks. Even when I use a wired connection it doesn't always work.
View 3 Replies View Relatednot sure exactly when this broke, but for some reason I'm not able to use CTRL-ALT-F1 anymore to fall back to the first virtual console.I can kill X with CTRL-ALT-BACKSPACE just fine, but I'd like to be able to get a normal shell to kill things when I've messed too much with graphical stuff.
View 4 Replies View Related