Fedora Installation :: FC4 - Installer Does Not Recognize Hard Drive
Apr 18, 2009
I have this laptop that I just reformatted in hopes of doing a dual boot between XP and FC4. It is an Acer Aspire 5315-2153 (the Wal-Mart special). I reformatted the drive; the Windows partition is in NTFS and then I have a 10GB partition in FAT32 for Linux. When I try to install FC4, the disk boots into the installer, then it tells me that it does not recognize any hard drives (the disk in this laptop is a Hitachi HTS541680J9SA00). It asks me if I want to load any drivers, and I tried a few and still no success. Any way, after it goes through that, it tries to start anaconda and after that launches it goes to a black screen and nothing happens. So, did I do anything wrong in the Windows install that won't allow the disk to be found? The XP disk only allows a format in NTFS, otherwise I would have done FAT32 on the whole drive. Second, is the anaconda problem something related to the HDD issue, or does anyone think that it may be a separate issue?
View 14 Replies
ADVERTISEMENT
Apr 1, 2009
There are 3 IDE drives in this box.
hda has Debian Lenny installed (with swap) and is to remain.
hdb1 has a linux distro on it.
hdb2 is a data partition and is to remain.
No other partitions on hdb.
HDD is data only (not really relevant but mentioned for completeness)
The system boots via Grub from MBR on hda.
I'm trying to install F10-i686-KDE-LiveCD on hdb1 but F10 won't allow it without modifying the partition tables which will, of course, wipe my data on hdb2. hdb seems to be a happy disk; e2fsck shows it clean and both partitions open properly in Konqueror within the LliveCD.
View 4 Replies
View Related
Aug 3, 2010
I've been trying for hours now to get Ubuntu 10.04 Netbook Remix onto my HP Mini 1030NR. It boots up fine from the flash drive, but then when I go to install UNR on the hard drive I get through the first 3 steps and then get stuck. It goes to the "Prepare partitions" screen but no devices are shown to be partitioned. I formatted the hard drive I'm trying to install on on another computer to NTFS, so it should be blank and ready to go? I should probably mention the drive doesn't show up in GParted either. Is there something obvious I'm overlooking?
I've tried the methods suggested in this thread to no avail: [URL]
View 1 Replies
View Related
Jun 10, 2011
I am trying to install Ubuntu 11.04 64bit on my computer, I downloaded it onto my flashdrive from [URL]... When I reach the installation screen all the boxes are checked except 4.4Gb of space available, I know I have enough space because I am using a 1TB hard drive, I also have Windows 7 installed and it recognizes my hard drive. I have tried this with my hard drive partitioned and unpartitioned. I only have 1 hard drive and it has never been part of a raid array. I've also looked on google and the Ubuntu forums and still can't find anything relevant
View 1 Replies
View Related
Sep 26, 2010
I've just put together a new machine and as I expected, there are some issues with hardware. I've just tried to set up the installation of ubuntu, got to the partitioning section and only my external hard drive is being picked up. The internal hard drive is a 1TB SATA drive plugged into a 6GB/s DATA port on my m/b (Gigabyte GA-P55A-UD4 running Intel i5 760 processor). I'm probably going to try the alternate CD to see if that works, but does anyone know if this is a common problem for any of my hardware? (I did a google but couldn't find anything).
View 3 Replies
View Related
Dec 10, 2010
I've bought new PC, and installed win 7 first. Then i've resized my disc and left the half of it unallocated for my ubuntu. But the ubuntu installer doesnt see my hard disk. when i run fdisc -l, the only thing that i see is my usb from wich i'm booting. I know that this is a common problem, searched for help on the web for hours and nothing worked.
View 9 Replies
View Related
Jun 26, 2015
“toshiba satellite u840w with hard disk drive and a solid state disk cache”
Debian 8 installer does not detect the hard drive during installation
I've recently tried to installed Debian 8. The problem is that the partition menu gives me these 3 options:
1. Configure iSCSI volumes
2. Undo changes to partitions
3. Finish partitioning and write changes to disk
There are no options for defining partitions or any hard drive during installation. After searching the internet i found that the problem because the solid state disk SSD cache. How I install a Debian 8 with computer which has a hard disk drive and a solid state disk cache.
more info: I want windows 7(64) and debian dual boot
View 14 Replies
View Related
Apr 18, 2010
I'm running into a weird problem when trying to install from the live CD I'm running. Basically, I have two hard drives: sda, a 160GB HDD which has Windows 7 on it, and is the one I would like to put kubuntu on; and sdb, which is a plain 500GB NTFS file system I keep all my personal stuff on.When I get to 'disk setup' and choose 'install side-by-side', it defaults to sdb instead of sda and I can't change it. I've created a 20GB partition on sda, which is where I want to put kubuntu, but it still defaults to sdb. I also can't figure out how to install to where I want using the advanced partitioning menu.
View 3 Replies
View Related
Mar 3, 2010
I have 4 hard drives in my computer...2x 74gb raptorsand 2x 640gb caviar blacksi just wiped windows 7 from the first raptor to install linux... now when i try to install linux it tries combining the 2 raptors as a raid (which i don't have them set up for)i just want to install it on my 1st raptor.i disabled the dmraid and that took care of it trying to combine them as a raid, but then it won't recognize either of the raptors.so i try gparted to format them. and i succeed.but when i try to install again. it still doesn't recognize the raptors... and only my 640gb blacksso i disconnected the power from the blacks... but to no avail, now no hard drives show up when i'm trying to install ubuntu... i am stumped.sorry if that doesn't make much sense... ask questions and i will be glad to answer them, its very frustrating.
View 6 Replies
View Related
Mar 19, 2010
So I have the burned ubuntu CD, and I'm attempting to install it on a system that has one HDD with XP/Vista on it, and another that is completely formatted and unpartitioned. However, when I boot to the ubuntu CD, I can use the menus from the bottom, and select the language when initially prompted, but I can't select any of the menu options except for boot from first hard drive.
View 1 Replies
View Related
May 1, 2010
Trying to install Fedora 12 using the 6 CDs. Trying to install on an older x86 box.Problem is that when detecting my hard drive, Fedora 12 recognizes it as a sda hard drive instead of hda hard drive. I have no SCSI connected to my computer what so ever. It's an old fashion PATA Western Digital hard drive.If I proceed with the install, Fedora 12 only installs 200MB of the OS from the first CD only. No options for additional software or anything.
View 1 Replies
View Related
Sep 3, 2010
The Fedora installer won't display my two SATA hard drives. I've tried both the x86_64 live CD and DVD. On the live CD, fdisk -l displayed nothing. However, if I click "Specialized Storage Devices" a devices shows up as "BIOS RAID set (stripe)" with a capacity equal to both my hard drives. I don't even have RAID enabled in BIOS - it is set to AHCI. Other os installers display the hard drive correctly.
Specs:
2x 640GB western digital caviar blacks
ASUS M4A78T-E 790GX motherboard
View 2 Replies
View Related
Oct 12, 2010
I have a ssd cosair harddisk with both usb and sata connecters. If I connect it with sata anything is working fine, and I managed to install Fedora core 13.
But I also want to be able to use the harddisk when it is connected with usb and that causes problems.
When I boot the Fedora Core 13 dvd It can't detect my usb harddisk.
When booting in install mode it just don't detect the harddisk.
When booting the dvd in rescue mode it don't detect the harddisk, and it don't create any entries in /dev/ for the harddisk. It is like there is no disk at all.
I have tested this on 3 different computers, so it is not a problem with my specific motherboard. So either it is a problem between my harddisk and Fedora Core 13, or there is some problems with the usb drivers in the boot image used by the Fedora core 13 dvd.
The disk is working fine if I connect it via usb to an existing Windows install, so the usb connection is working.
I installed Fedora core 13 with the harddisk connected to sata and then re-connected the harddisk to usb. It then boot up, but complain about missing root filesystem. Most likely caused by missing usb driver in my kernel.
But anyway, what I really want is the ability to boot from both sata and usb, so I can take the harddisk with me and boot it on other computers with usb.
So is there a command which allows me to build an kernel image which can boot from usb or am I trying to do something which is not really supported?
I did update my fstab to use LABEL=myroot
There is 1 Windows partition(NTFS) and 1 linux partition on the disk. (No seperate /boot partition and no swap)
View 1 Replies
View Related
Jul 20, 2010
My fileserver is running 8.04 LTS. I have 4 drives in an LVM and a separate drive for the OS. The OS drive is dying. When I replace the OS drive, I figure I'll go ahead and upgrade to 10.04.
Will the 10.04 installer recognize the existing LVM? Do I need to do anything to the LVM (apart from backing up the data) before I install 10.04?
View 1 Replies
View Related
Apr 4, 2010
So I tried to install Ubuntu on my Acer Aspire ASE380 desktop, and I think during the partition portion. I think I messed up the hard drive.
Now my computer won't recognize my hard drive. I've tried using the acer repair disks I made, I tried unplugging and checking all the cords and lines, I tired flashing the BIOS, I've tried using other boot disks like Ultimate boot CD, and Acer support is no help either.
I really don't know what to do now. It shows nothing in the boot setup or the BIOS set up. I've also tired the ALT - F10 for acer computers to enter and repair partition and nothing.
I just want to get this thing up and running. I'm tempted to just buy a new hard drive.
View 2 Replies
View Related
May 31, 2010
Is there any way to make windows recognise my second hard drive (Which is fully exclusive to ubuntu) and access it? Iv'e been getting a few BSOD's since installing ubuntu and I'm pretty sure it's because windows keeps trying to access it and failing.
View 2 Replies
View Related
Aug 10, 2009
I would like to install Fedora 11 on an ASUS P5L-VM 1394 motherboard with a 3 GHz Pentium 4 CPU. This is an LGA775 socket mobo with a Intel 945G chipset. Two SATA hard drives are plugged into SATA ports. An IDE DVD drive is plugged into the IDE/ATA port. Using the 32 bit Fedora 11 installation disk, I have seen two cases:
1) No hard drive recognized. When i get to the disk configuration screen, there are no options to choose from.
2) By monkeying around with the BIOS settings or switching the SATA ports the disks are connected to, I can get an alternative mode in which no drivers are found for the DVD drive either.
Currently, a version of Ubuntu is installed. UPDATE: The board was purchased in a P3-PH4C barebones, which for unknown reasons requires a different BIOS issue than the regular P5L-VM 1394. Updating to the most recent BIOS does not resolve the problem. One the installation procedure fails to recognize the hard drives, going into a shell and examining the boot up log shows that the kernel recognized both hard drives. So it's down to why the installation procedure is not recognizing them.
View 1 Replies
View Related
Apr 18, 2009
I have just changed my OS from Vista to Linux Fedora 10. After looking at my system I notice my SATA drive was not recognised its my 2nd drive. Is this a normal think or can it be fixed.
View 1 Replies
View Related
Apr 12, 2010
My 13 year old Pentium 3 1.3 ghz machine is finally ready to call it quits. specifically, my slave drive where all of my music is stored. I can access a very small portion of the the files on the HD, The files are still there but are not showing up. any ideas on how I could access this drive. I wanted to try to reinstall my os on the primary drive in hopes that it wouldget it working, unfortunately I've run into what's seems to be a common problem of my usb keyboard not being recognized.
View 1 Replies
View Related
Jul 8, 2011
I have a samsung removable hard drive, which have 3 fat32 partitions on it. When I plug into the usb. nothing happened and i just see a sdc was added in /dev/...so, there's nothing wrong with the drive, because i can use it on windows and ubuntu.
View 10 Replies
View Related
May 2, 2010
start getting Linux up and running. Like a lot of people, I chose an older computer I could fuss with, a 500mhz 256meg ram machine, and decided to install Puppy on a spare 40meg hard drive I have, as my bios does not boot from usb...I think...
Anyway, I have found that my bios does not recognize the hard drive when formatted to ext2! I have taken the drive and formatted it back to ntfs, and my bios recognizes it, and then back again to ext2, and nope, it's not there, thus I am still booting puppy from the cd...sigh...
Is my bios so out of date that I'm just out of luck? Is there anyway to check this?
View 5 Replies
View Related
Jun 13, 2010
getting freespire to recognize my 2nd hard drive and allow me to use it for things I want to save there and such. I also cannot get CNR to come up in my browser and need some information as to how to install programs.how to find installable programs,and install them.
View 1 Replies
View Related
Jul 19, 2011
Long time Slack user, thought I would try to update my old laptop (Toshiba Satellite with AMD K6-2 333 MHz, 128 MB RAM, 40 GB hard drive) from 10.2 to 13.37 in celebration of the newest version :-)
By update, I mean a complete wipe and reinstall, just to be clear.
So 10.2 runs well, everything looks shiny (XFCE of course) but when I try to install 13.37 I run into trouble. I figured out to boot with huge.s instead of hugesmp.s, but when I try to run 'setup' I get an error that says I have no partitions. mkay, I try fdisk (or cfdisk), but I get literally NO response - no error, no nothing but a return to the command promt. It is exactly as if fdisk does not recognize there is a hard drive there at all.
I boot back into 10.2,check the BIOS, everything looks fine, I have a drive mounted at /dev/hda1, swap at /dev/hda3. Are there some additional parameters I should be booting with? Does it matter that the hard drive is ATA?
View 11 Replies
View Related
Oct 14, 2014
I am currently trying to install Debian Wheezy 7.6 x86_64 on an Intel Server System R2224GZ4GC4, but the Installer doesn’t recognise any of the devices attached to the onboard SATA controller.
Debian Version
Debian Wheezy 7.6 x86_64
Hardware used
Server: Intel Server System R2224GZ4GC4
Motherboard: Intel S2600GZ4
Onboard SATA Controller: Intel Patsburg 4-Port SATA Storage Control Unit (rev 06)
Device on Port 0: Samsung 840 Pro Series SSD
Device on Port 1: Samsung 840 Pro Series SSD
Device on Port 2: Samsung 840 Pro Series SSD
Device on Port 3: Intel 510 Series SSD
While the onboard SATA controller does support so-called “fake RAID,” this ‘feature’ has been disabled (i.e., the BIOS setting “SAS/SATA Capable Controller” is set to “INTEL(R) RSTe”). This is confirmed by the controller during the boot-up URL...Weirdly enough, the Intel 510 Series SSD contains an old system (Debian Squeeze 6.0, Kernel 2.6.35-5-amd64), which can boot and which does recognise all SSDs.
Remedies tried
* I’ve compiled the list of SCSI, SAS and block device related modules that the Squeeze-System, which recognises the SSDs, used and manually loaded these modules during the install process.* I’ve tried to rescan the SCSI bus by:
Code: Select allfor host in /sys/class/scsi_host/*; do echo "- - -" > $host/scan; done* I’ve tried to remove all disks, save for the Intel 510 Serives SSD.* I’ve tried all of the above combined.
View 2 Replies
View Related
Oct 13, 2010
I have been upgrading from 9.04 to 10.04. Now, I want to install 10.10 from the beginning without losing the data in my current partitions but when I run the Maverick installer it recognize my disk as a whole with no partitions. From another posts, I suspect that the problem is in the partition list because it seems to be a duplicate partition but don't know how to fix it. This is the fdisk output:
Code:
jgarcia@jgarcia-laptop:~$ sudo fdisk -lu /dev/sda
Disco /dev/sda: 250.1 GB, 250059350016 bytes
255 cabezas, 63 sectores/pista, 30401 cilindros, 488397168 sectores en total
Unidades = sectores de 1 * 512 = 512 bytes
[Code]....
View 2 Replies
View Related
Jun 9, 2010
VMware virtual machine with the RedHat9 can not recognize win7 hard drive, so can not be mount,how to solve? Situation is showed in the Figure,when type the command ,it do not display the hard disk, the picture is below [URL]
View 7 Replies
View Related
Mar 30, 2011
i have installed fedora 14 with so many libraries ,development tools installed on my pc but i usually have to present some projects which can run on my system .........and can't be executed or compiled due to absence of libraries and tools there so, i there some way to so that i can use this current installation on my hard drive of my pc to some external media like external hard disk and plug and use that installation anywhere on any system..
View 2 Replies
View Related
Apr 23, 2010
I have installed ubuntu in my D drive on my lenovo laptop but it not recognizing D drive only recognize C drive
View 1 Replies
View Related
May 20, 2015
I'm trying to install jessie on a new computer, but the installer does not see the hard drives. I copied the DVD-1 iso to a usb stick with dd (also tried the netinstall) and it boots, but when I get to partitioning, it only sees the usb drive. If I go to another virtual console and run dmesg or fdisk -l, all drives are seen correctly.
Back up a little - at first I tried the on-board raid, but when the installer couldn't see the drives, I went back into the bios and reset the sata mode to ahci. I've got it set to use bios/legacy OS, or whatever it's called, fast boot is disabled. Even if only one drive is connected, the debian installer does not see it. Then I read up on the fake raid I was trying to use and decided to go with software raid. Can't do that if there's no hard drives listed in the partitioner.
My own installer (refractainstaller) does work, and I've installed jessie with it a couple of times onto one drive, but I really wanted to use raid and lvm, and my installer doesn't do either of those things. No optical drive, but if that's the only way to install, I'll pull the one from my current box and use it for the install. I think I still have a blank CD or DVD lying around.
Hardware:
ASUS H97-PLUS LGA 1150
Intel core i3 (the cheapest one at newegg)
WD Black 1TB drives (2)
GSkill cheap memory, which already passed a memtest.
View 4 Replies
View Related
Jun 23, 2009
I've been trying to get Fedora 11 (x86_64, netinst) installed on my machine, but am having trouble with the hard drive selection and partitioning. This machine has 2 x 320GB hard drives. One for Windows, and one for Linux of course.
When I first tried the install, both hard drives were attached to the computer. I was expecting to see the drives seperately so that I could partition and install on only one of the drives, but device mapper kicked in and showed me a single 640GB long partition. Not very helpful in my case.
I decided to simply unplug the Windows drive so that fedora didn't see the two identical drives and so would not try to map them. However, with only the linux drive plugged in, the installer doesn't see it. There are no hard drives to select from in the installer.
As a test, I plugged in the windows drive solely and unplugged the linux drive, and low-and-behold, fedora sees the windows drive. This is getting slightly confusing at this point as both the hard drives are identical. I can't see why the installer would recognise one but not the other. Yet it recognises the extra 320GB of hard drive space if both drives are plugged in and device mapper tries to raid them. I tried the debian installer to see if it had the same problem, but it was able to see and install on this drive. I would have tried OpenSUSE as well but this computer doesn't have a DVD drive.
I haven't tried a "nodmraid" boot option yet, so I am going to try that tonight, but I'm interested to hear what the community thinks of this problem.
System Specs:
DFI LANParty UT NF680i LT SLI-T2R
Intel Q6600
Corsair XMS2-800 2x2GB
2 x Seagate Barracuda 320GB
I've also had a 640GB plugged in that was detected fine (probably because dm didn't try to raid it being the odd hdd out) but has been removed while I'm troubleshooting the fedora install.
View 5 Replies
View Related
