Debian Installation :: Installer Fails To Recognize SSDs Attached To Intel Ctrl
Oct 14, 2014
I am currently trying to install Debian Wheezy 7.6 x86_64 on an Intel Server System R2224GZ4GC4, but the Installer doesn’t recognise any of the devices attached to the onboard SATA controller.
Debian Version
Debian Wheezy 7.6 x86_64
Hardware used
Server: Intel Server System R2224GZ4GC4
Motherboard: Intel S2600GZ4
Onboard SATA Controller: Intel Patsburg 4-Port SATA Storage Control Unit (rev 06)
Device on Port 0: Samsung 840 Pro Series SSD
Device on Port 1: Samsung 840 Pro Series SSD
Device on Port 2: Samsung 840 Pro Series SSD
Device on Port 3: Intel 510 Series SSD
While the onboard SATA controller does support so-called “fake RAID,” this ‘feature’ has been disabled (i.e., the BIOS setting “SAS/SATA Capable Controller” is set to “INTEL(R) RSTe”). This is confirmed by the controller during the boot-up URL...Weirdly enough, the Intel 510 Series SSD contains an old system (Debian Squeeze 6.0, Kernel 2.6.35-5-amd64), which can boot and which does recognise all SSDs.
Remedies tried
* I’ve compiled the list of SCSI, SAS and block device related modules that the Squeeze-System, which recognises the SSDs, used and manually loaded these modules during the install process.* I’ve tried to rescan the SCSI bus by:
Code: Select allfor host in /sys/class/scsi_host/*; do echo "- - -" > $host/scan; done* I’ve tried to remove all disks, save for the Intel 510 Serives SSD.* I’ve tried all of the above combined.
View 2 Replies
ADVERTISEMENT
Nov 25, 2015
This laptop has been in the mainstream news as the cheapest Windows laptop available. Unfortunately it has a 64-bit CPU with 32-bit UEFI that dumps to the grub shell before installation. In addition, the built-in keyboard does not work.
As far as the dump to shell problem, this seems like something is not setup correctly in the grub UEFI configuration. This "hybrid" notebook should be using the multi-arch as I understand the situation. I noticed there is no grub configuration file in the multi-arch netinst ISO when I mounted it and looked around. I also noticed the standard netinst ISO is not easily mountable: there are errors when I try to mount the individual partitions to inspect the grub configuration. Additionally, Kubuntu boots perfectly aside from the keyboard issue. Devuan also boots when I modify the netinst to bypass gummiboot and use grub directly. Finally, the multi-arch grub shell freezes up when autocompleting and searching through the drives for the grub config, leading to a forced reboot. As an extra note, I tried 2 different flash drives and CD install media with the same results.
I tried many, many grub kernel combinations to fix the keyboard issue. It works in grub, but not in Linux. I was ultimately going to try a newer kernel to fix it.I was in a hurry to get something set up so back to the store it goes.
View 1 Replies
View Related
Mar 10, 2016
I am trying to clean install Jessie 8.3.0 onto an old PC, where I already have wheezy 7.7 working. I am using the 3 DVD- i386, which passed the integrity check.
Installation goes on smoothly till completing the "Select and Install SW" stage from 1st and 2nd DVD. At this point I get the warning that "Installation step failed, ..", giving the choice to repeat.
When repeated, the process gets completed (without asking for 2nd DVD), the new installation boots normally, but the KDE desktop opens irregularly, with some basic applications missing, and some flaws during certain operations.
The APT does not show any missing/broken link. I tried and repeat the installation with different choices as for kernels and/or desktops, but got the same result. I cannot guess where the problem originates, nor whether it is a known bug of the installer.
View 6 Replies
View Related
Sep 22, 2015
Debian 8 "Jessie"
AMD CPU
EFI motherboard
System was working reliably. Moved components into a new case. Now system will not boot. Either gives error that the disk is not bootable or displays the motherboard configuration screen.
I am able to boot Debian with a USB drive and have attempted fixes in "rescue mode".
I confirmed that the system is booting to EFI mode.
I have tried re-installing the grub-efi package and re-creating the Grub config file with update-grub.
When re-installing Grub I receive "Discarding improperly nested partition ..." warnings but the installation succeeds. I have searched this warning message and the forums seem to say that it can be ignored.
I have tried re-setting the motherboard NVRAM using the jumper block.
The computer shows "debian" as a boot choice in addition to the usual raw drive model listing. However, neither of the choices will boot successfully.
View 4 Replies
View Related
Apr 20, 2011
Having trouble installing 'Squeeze' 6.0.1a-amd64-netinst on a new AMD64 system.The installer boots and runs fine until it gets to hard disk detection. Then it hangs for about 20 minutes showing a blue screen, during which time the HDD-activity light flickers every 5 seconds. Eventually it says it can't detect a hard disk, and displays a (longish) list of possible drivers; no idea which, if any, would suit.Anyone else installed (successfully or otherwise) on this combo?
View 3 Replies
View Related
Jan 12, 2011
I have been thinking about upgrading my RAID setup from a pair of Intel X25s running the software based RAID included with ubuntu to four Intel X25s running off a PCIe based controller. The controller is an HP P400 which I know works great on ubuntu (I have other machines running it with SAS drives). My desktop has an Intel S5000XVNSATAR mainboard and I have an open PCIe v1.0 8x (physical) slot that is wired 4x. The controller is 8x and will fit fine. How much of a performance hit do you think I will see running this 8x controller in the slot wired 4x with four Intel x25s in a RAID 10? Will I have enough bandwidth with the 4x for those SSD's?
View 4 Replies
View Related
Feb 15, 2015
I have two SSDs on which I have configured md RAID 0, with a 16 KB chunk size. My understanding is that Wheezy (and later) installations are smart enough to align partitions on block boundaries, even in md RAID configurations, but to satisfy my own natural distrust, how do I go about actually confirming that it has done the right thing? I have a single root logical volume within an LVM partition, but neither the logical volume nor the LVM partition occupy all available space, and the LVM partition is offset from the end of the disk.
My concern arises from the fact that, when I look at the sysfs entry for my root partition:
# cat /sys/devices/virtual/block/md126/md126p4/start
804818048
This number is not evenly divisible by 4096.
View 2 Replies
View Related
Jul 20, 2010
My fileserver is running 8.04 LTS. I have 4 drives in an LVM and a separate drive for the OS. The OS drive is dying. When I replace the OS drive, I figure I'll go ahead and upgrade to 10.04.
Will the 10.04 installer recognize the existing LVM? Do I need to do anything to the LVM (apart from backing up the data) before I install 10.04?
View 1 Replies
View Related
Apr 18, 2009
I have this laptop that I just reformatted in hopes of doing a dual boot between XP and FC4. It is an Acer Aspire 5315-2153 (the Wal-Mart special). I reformatted the drive; the Windows partition is in NTFS and then I have a 10GB partition in FAT32 for Linux. When I try to install FC4, the disk boots into the installer, then it tells me that it does not recognize any hard drives (the disk in this laptop is a Hitachi HTS541680J9SA00). It asks me if I want to load any drivers, and I tried a few and still no success. Any way, after it goes through that, it tries to start anaconda and after that launches it goes to a black screen and nothing happens. So, did I do anything wrong in the Windows install that won't allow the disk to be found? The XP disk only allows a format in NTFS, otherwise I would have done FAT32 on the whole drive. Second, is the anaconda problem something related to the HDD issue, or does anyone think that it may be a separate issue?
View 14 Replies
View Related
Jan 23, 2009
I am trying to upgrade RH9 to F10. I have downloaded dvd iso image i386. The SHA1 integrity check passes. The installer fails media check due to "errors". I did an independent verification of the DVD and zero errors found. Download was from Fedora's own torrent, so files should be verified anyway. If I bypass the media check I get the message : Running anaconda 11.4.1.62 the Fedora system installer - please wait.....
[Code]....
View 7 Replies
View Related
Oct 13, 2010
I have been upgrading from 9.04 to 10.04. Now, I want to install 10.10 from the beginning without losing the data in my current partitions but when I run the Maverick installer it recognize my disk as a whole with no partitions. From another posts, I suspect that the problem is in the partition list because it seems to be a duplicate partition but don't know how to fix it. This is the fdisk output:
Code:
jgarcia@jgarcia-laptop:~$ sudo fdisk -lu /dev/sda
Disco /dev/sda: 250.1 GB, 250059350016 bytes
255 cabezas, 63 sectores/pista, 30401 cilindros, 488397168 sectores en total
Unidades = sectores de 1 * 512 = 512 bytes
[Code]....
View 2 Replies
View Related
Feb 7, 2010
Whenever I try to install Ubuntu 9.10 x64 from a Live CD the installer freezes or quits when trying to partition the drive. I tried booting into the Live environment and using GParted but that would only let me make a ReiserFS partition without crashing. With the Reiser partition I tried the installation program again but this time the installer froze when trying to install the files.
My system specs are:
AMD Athlon 64 X2 6000+ (3.0GHz)
4GB RAM
500GB SATA2 HDD
ATI Radeon HD 4770
Currently it also has a second SATA2 HDD with Windows 7 installed but I disconnect this during installations
View 4 Replies
View Related
Apr 23, 2010
I tried to install 64bit 10.04 Release Candidate but it fails every time. I have been using 64bit 9.10 Karmic on this computer so it's suitable for installation.
I tried to install from USB stick and from CD but same error at the same point! It fails just befere it starts to ask your locations etc...
There must be something totally wrong on installer. Checksums are ok etc...
Errors seen with CD and USB stick installation: Pop up: "Istalltion failed The installer encountered an unrecoverable error. A desktop session will now be run so that you may investigate the problem or try installing again."
On command line I can see following error message on CD:
These errors with USB stick:
View 9 Replies
View Related
Sep 8, 2010
I have just upgraded my Debian 4.0 box to Debian 5.0. The upgrade is ok and the version of debian is 5.0.6.
Webmin, despite all my efforts, is still displaying 4.0 and when I force it to 5.0 manually, it states: "Warning - Your system is actually running Debian Linux version 4.0."
View 2 Replies
View Related
Jun 12, 2009
When using the manual partitioner on the fedora 11 installer on the live cd, both for 64 bit and 32 bit, it will not allow me to create a new partition. I understand that I have four primary partitions and it cannot have more than that, so I tried deleting one of the partitions, then creating the new ext4 partition for F11. It still fails and gives me the same bugsee attachment)
how to read this, especially since there is so much there. I see at the top it says that there are 4 primary partitions, could it possibly still be seeing 4 primary partitions when trying to create the new one, even though I am deleting one of them? Other than this, I truly have no idea what else I can do.
EDIT: Attachment wont load up for some reason, here is some of the error file:
anaconda 11.5.0.59-1.fc11 exception report
Traceback (most recent call first):
File "/usr/lib64/python2.6/site-packages/parted/disk.py", line 183, in addPartition
constraint.getPedConstraint())
[Code]....
View 5 Replies
View Related
Jan 31, 2010
I'm facing a problem installing Fedora 12 x64 on my desktop.I've been trying to get the Graphical Installer (anaconda) to run, in vain. The error message I get is reproduced below:
Code:
(EE) [drm] drmOpen failed
(EE) NOUVEAU(0): [drm] error opening the drm
[code]....
View 1 Replies
View Related
Feb 7, 2010
The Install program is failing to see the hard disk!
Now heres the really weird bit. The live cd can see the drive just fine.
I have created partitions using gparted and the disktool also sees the drive just fine but as soon as I go back to the installer it shows no hard disk!
It's a SATA drive which I suspect might be a part of the problem.
Is there a way I can install without the install program?
Is there a way to make the install program see the drive?
This is ubuntu 9.10 desktop.
View 2 Replies
View Related
Sep 2, 2010
I am trying to install Ubuntu as a secondary operating system on my Windows 7 PC.
System specs as follows:
AMD Athlon II X4 620 Processor 2.6 Ghz
4.00 GB RAM
ATI Radeon 4600 series video card
I downloaded the 32-bit ISO image from ubuntu.com and burned it to a CD. When I try to boot, I get a purple splash screen with a couple of icons on the bottom. Shortly thereafter, I get another screen that says Ubuntu and has 5 dots on it that change color from red to white in sequence. During this time, my CD drive is active. After a very long time, the drive goes quiet and I get an error that the installer can't find the username or password. I don't remember the exact text of the error message. The system was hung and required a hard boot to recover.
Reading these forums, I rebooted the computer and this time pressed the escape key once the display had changed to the Ubuntu with the dots. The username/password error came up quickly and was followed by several "Bus error" messages. I ejected the CD and restarted the computer in order to come here for enlightenment. I'm reasonably good with Windows but a total neophyte when it comes to Linux. I'm going to try it again and this time record the exact error message (which is what I should've done initially).
[Code]....
View 8 Replies
View Related
Jan 30, 2011
I have a Brother mfc-8890dw that is attached to my local area network.I can ping the static ip address of the printer and receive a reply. I can print from all applications.I cannot scan. I did modify the rules files but that only appears pertinent for usb attached devices. What do I need to do to get XSane to recognize my Ethernet attached scanner/printer?
View 2 Replies
View Related
Dec 21, 2009
I have attached usb memory to my Linux server and I want to add it to my /etc/fstab .Can you please let me know how can I recognize it from my"/dev/?" list ?
View 14 Replies
View Related
Feb 3, 2011
So I decided to reinstall my 10.10 to undo the 'encrypted home folder feature.' I know are other ways to undo the encryption, but for various reasons I'd rather just do a quick reinstall and start fresh.Currently, I dual boot linux and windows, each with their respective partitions. There is also a storage partition that is fat32 to swap files between the two OSes. So the partitions are:
[Code]...
View 5 Replies
View Related
Mar 22, 2011
I used Ubuntu before, without problems but since the 10.04 version it won't recognize my partitions. I formated my laptop and partitioned it, installed Windows 7 64bit, which I need for my work, and wanted now to install Ubuntu 10.04/10. I then used GParted to check my Harddisk and it is having troubles to recognize my partitions, too while Windows finds them. GParted is giving me an error message saying my partitions are oversized. I am still in the beginning of my Linux experiences and so I don't know what to do. I have two 250GB harddisks (how Windows recognizes them),
[Code]....
View 9 Replies
View Related
Aug 20, 2015
I would like to make a boot RAID0 LVM on a pair of SSDs (sdc and sdd). The system is already running off of a HDD. I built the RAID0 through the Asus BIOS on the Intel controller. I see:
# cat /proc/mdstat
Personalities : [raid0]
md124 : active raid0 sdc[1] sdd[0]
59346944 blocks super external:/md126/0 32k chunks
md125 : active raid0 sda[1] sdb[0]
222715904 blocks super external:/md127/0 32k chunks
[code]....
My challenge is that when I open Gparted, it only show one disk at a time. I would like to learn how to use Gparted to partition this RAID0 with a UEFI sector and LVM for the rest.
View 2 Replies
View Related
Aug 10, 2009
I would like to install Fedora 11 on an ASUS P5L-VM 1394 motherboard with a 3 GHz Pentium 4 CPU. This is an LGA775 socket mobo with a Intel 945G chipset. Two SATA hard drives are plugged into SATA ports. An IDE DVD drive is plugged into the IDE/ATA port. Using the 32 bit Fedora 11 installation disk, I have seen two cases:
1) No hard drive recognized. When i get to the disk configuration screen, there are no options to choose from.
2) By monkeying around with the BIOS settings or switching the SATA ports the disks are connected to, I can get an alternative mode in which no drivers are found for the DVD drive either.
Currently, a version of Ubuntu is installed. UPDATE: The board was purchased in a P3-PH4C barebones, which for unknown reasons requires a different BIOS issue than the regular P5L-VM 1394. Updating to the most recent BIOS does not resolve the problem. One the installation procedure fails to recognize the hard drives, going into a shell and examining the boot up log shows that the kernel recognized both hard drives. So it's down to why the installation procedure is not recognizing them.
View 1 Replies
View Related
May 20, 2011
WHERE TO WRITE :"modprobe snd-hda-intel model=acer "? I have problem with soundcard. In fact it is not recognised and of course I don't have sound.After working and looking for solutions I found that if I make this command : as root # modprobe snd-hda-intel model=acer
the system recognize the soundcard and it's starting and I have sound. .Now ,I put a "stupid" question :Where to write the message above :modprobe snd-hda-intel model=acer ,in which config file from /etc with nano i.e.,in this way I hope the change become permanent and I don't need to command everytime to make system working.
View 8 Replies
View Related
Jul 25, 2010
I am running a server that is mostly headless, but does run the Gnome environment (I have ubuntu-desktop installed). I usually administer it via VNC over SSH. My problem is that when I reboot the system over SSH, the system fails to fully load the GUI, which prevents me from connecting via VNC (although SSH still works).
When I connected a monitor and rebooted, the system booted up fine. It appears that the GUI will not load without an attached monitor, which never happened before in previous Ubuntu versions. I do use many commands but prefer a GUI for certain tasks and visualization of my work since my system has the resources to spare. Running Lucid Lynx
View 6 Replies
View Related
Aug 13, 2010
This is a problem which has been plaguing me ever since the upgrade from Karmic to Lucid.
I used to be able to log into any one of the seven TTYs.
CTRL-ALT F1-six all work fine. Problem is if I log into one I can't get back to the GUI.
Immediately after the upgrade, I was told by some people that this was deprecated along with startx and I should use sudo gdm service start instead.
This doesn't work for me If I have to open a terminal when a nasty game freezes and I have to kill it from a terminal.
View 9 Replies
View Related
May 1, 2011
I have 10.10 installed within my Windows Xp.All was fine.Then,I upgraded to 11.04.Boot screen etc is fine .Log in is automatic in Classic.Unity & Compiz not supported.Now,again everything is fine except that my xp partitions are not recognised and hence I can not mount them and access them.
View 5 Replies
View Related
Apr 22, 2011
I get black screen when i press ctrl-alt-f1 or when i try to stop gdm, pressing alt-f7 nothing happens.
vga is ati hd 5650 how can i fix?
View 1 Replies
View Related
Jan 5, 2010
I have 3 layouts: USA, Russian and Hebrew. In Hebrew the W key is mapped to apostrophe, so Ctrl+W in Hebrew layout doesn't close tabs in Firefox. There is no workaround for it as I see by now, so I am trying to get it work this way:I want to map Ctrl+W in Hebrew layout(which is actually a Ctrl+') to be a Ctrl+w. Here is what I got from xmodmap:Code:$ xmodmap -pke | grep 25keycode 25 = w W Cyrillic_tse Cyrillic_TSE apostrophe WAs you can see, there are pairs for each layout, each pair tells what happens without and with the Shift key pressed.
View 2 Replies
View Related
