Fedora Installation :: F10 On SAS - Add Static IP Fails
Feb 16, 2009
I'm getting ready to install F10 x64 on a Supermicro 7045A-3B on an SAS; I would like to partition the drives free space; I have an OS (Windows 2003 Server R2 x64; sorry still have a few apps that need it; can't wait for the day I can see the end of MS on my computers) on it and I don't want to hose it.
Motherboard: X7DA3
16 GB RAM
Adaptec AIC-9410 SAS Controller (Dual 136 GB Seagate SAS drives in RAID 0)
I also have 1 SATA Drive bay; maybe I could install Windoze on it; but I still need to know how to install F10 on an SAS. So far my stumbling block has been when I click on advanced storage device; when it ask for Network configuration I add my Static IP; it fails; I note that it does this on all installs of F10 on other computers as well; but installed with no problem; problem here seems to get past that after hitting cancel; going back I get to Add iSCSI; I have no idea what information to put in blocks: Target IP Address, iSCSI Initiator Name, CHAP User name, password and reverse info for them. I do admit how that I don't think I need to add an iSCSI device; I just don't see the SAS as an option and don't know how to add it.
I am struggling with what might be a minor problem. I have a home computer which I would like to setup as a webserver and hence give it a static IP address. It is connected to by wire to a router that is connected to the WAN via PPPOE. If I enable the network card on DHCP it works fine in browsing the web. If I now set it to static IP address it does not brown. Essentially I use the command setup to run the static IP setup. I then set my IP address to 192.168.254.X , the subnet mask 255.255.255.0 and the default gateway to 192.168.254.1 (this is the router connected to the WAN). I am able to ping the router, however when I try and browse on static it does not work. Your help will be most appreciated as this has taken way too long to solve and I have Googled as much without success.
Running Gentoo with kernel 2.6.29 on a Sparc Ultra 10. I'm having problems with my cable modem connection failing, so I've added a static route that enables me to log into the modem's diagnostics page at 192.168.100.1 when the connection drops; my /etc/conf.d/net looks like this (with the comment lines removed).
I am trying to upgrade RH9 to F10. I have downloaded dvd iso image i386. The SHA1 integrity check passes. The installer fails media check due to "errors". I did an independent verification of the DVD and zero errors found. Download was from Fedora's own torrent, so files should be verified anyway. If I bypass the media check I get the message : Running anaconda 11.4.1.62 the Fedora system installer - please wait.....
I had been running Fedora 12 for some time without much difficulty until I had to change the motherboard of the computer. The new MB comes with Realtek 8112L PCIe Gigabit LAN controller.I am not able to use this LAN controller without Network Manager. The problem is I am not able to set a static local IP with it. Network Manager -> Edit Connections -> Auto eth2 -> edit -> IPV settingsAs soon as I change Method to Manual, 'Apply' button gets grayed out.I am not able to save any change.
Ive installed about 50+ boxes with ubuntu/mint/fedora/etc but f15 is giving me a real headache...
I tried a fresh install over f14 with this drive (sdb, sda is my backup disk)
Installed obviously in part7
After rebooting (successful copied live image on hdd)
Code:
After another couple of installs (with lvm & w/o lvm) & even disconnecting the second harddrive -> same issue
Typing 'ls' in the rescue grub prompt returns
Code:
Cant 'ls /' into a single them - unknown filesystem (grub is installed in mbr of sdb) 'linux rescue' (wanted to try manual grub installation) command didnt work either.
Now again on fedora 14, same installation procedure, works fine. (and i wont bother doing a full distro upgrade from f14)
I am attempting to install Fedora 12 i386 from a USB DVD drive.
The DVD is initially recognized, and I go through the installation menu page and queries about language and keyboard. Then it asks me which hard drive partition contains the installation image. WTF?
CPU is Intel Core 2 Duo (mobile) T5500.
Edit: I popped the cover, temporarily added an SATA DVD drive, and installation is going OK. That pretty much isolates it to recognition of the USB DVD drive.
I tried a pre-upgrade last night and after downloading 7GB of stuff over night, (don't ask me why it was that much) I rebooted.
Everything looked okay until I got an error message that said that /mnt/sysimage/... (I can't remember exactly what the error message was, sorry) what did not have enough space and needed 19MB more to install the upgrades.
Now, this system quad boots between Fedora, XP, Vista and 7 with grub being the intial boot loader giving me the option of Fedora or the Windows bootloader.
What I don't understand is why the installer (anaconda?) is having a fit about space when I have 8GB RAM and the system partitions are >10GB in size.
I'm attempting to install F11 on my desktop. I am unable to complete the installation because the X environment for anaconda fails to start and instead the installation reverts to text mode (in which I cannot seem to to a custom disk partitioning layout for the installation, which I have to be able to do). This was not a problem with the Alpha or Beta, but the preview and now the final release have both had this problem.
My system: intel 3.16 core 2 duo 4gb ddr2 ram dual nvidia 9800gtx+
I'm having some problems on the line with ***. This is from a OpenEntidade.java class file and I'm trying to update EmprestadorView's variables.
EmprestadorView.java public class EmprestadorView extends FrameView { ... OpenEntidade.java ----------------- public class OpenEntidade extends javax.swing.JFrame {
I was trying to install fedora 10 onto my new computer, with the full dvd. my new computer has 2G ram, Radeon 4670 and a Gigabyte motherboard. after i started up the installation, while it saying "loading anacoda...." the line" X window fail to load. Back to text mode." So should i continue with the installation? because i fear that after i installed the fedora 10 onto my computer, i have to use it in text mode
I am new to Linux and so am trying different distros. I have ubuntu which runs ok and installed fedora 9 from a disc on Linux Format magazine which runs ok. However I have tried to upgrade to Fedora 10 from a disc but the pc fails to find the disc. It is the same drive I used approx 6 weeks ago to install Fedora 9 so I am at a loss.
I am attempting to install Fedora 11 on a Dell Windows Server 2003 computer from CD (I just want to override the Server PC with F11). I used this media in my class last night after testing it, so I know the media itself is good. We did have lots of issues getting the keyboard and mouse to work during the install attempts last night, too, but eventually it worked. Unfortunately, at home is a different story!
I boot from install Disk 1 and get to the first screen with the option of testing the media or skipping it and I only get one keystroke then nothing. F11 just hangs/stops/freezes/locks up. Reboots don't help and I attempted to install from the F11 DVD I made, too, but the machine completely wouldn't see that disk at all! The keyboard is connected directly to the computer via PS2. I don't have a USB keyboard laying around nor an adapter to try.
I would love to hook up my children with F11! I did manage to figure out what files to download, burn to disk and how to install F11 at school yesterday).
I am trying to upgrade from F11 to F12.Using Preupgrade, everything went well and then it asked me to Reboot. Anaconda started then says something about updating some files then the screen goes blank.
I'm newbie in Linux, but have used Windows and Mac OS X Leopard. Used RedHat in the past, and can't figure this out. I burned Fedora12-x86_64 DVD image on DVD, and start install. Whether I use "linux text" command from boot or just select Install at graphical prompt, everything goes OK until I select hostname. I leave it as "localhost.localdomain" and press Enter. It always give me an error "Can't load class=TimeZoneWindow".
My computer is connected via ethernet to my router, and I had no problems getting online in Windows. Now, in case there are hardware questions: Intel Pentium 4 with HyperThread enabled and 64bit support (Windows 7 Ultimate 64bit runs perfectly in 64bit mode) 2Gb of DDR 400Mhz RAM I have 2 SATA hard drives with RAID option as Mirror (BIOS settings - RAID or AHCI) And 128Mb ATI RAdeon X300 series. Pretty simple, but this error aborts my installation.
I tried to do Anaconda updates, but I have no clue about URL where the image is, ex: linux updates=[URL] or I tried configuring network: linux ip=192.168.1.113 netmask=255.255.255.0 gateway=192.168.1.1 dns=68.193.158.40,24.115.70.53 and no luck. Why does "Can't load class=TimeZoneWindow" appear? Is it a network issue or what? I've seen the screenshot for TimeZone screen in the Installation Guide, but I never get to it.
I upgraded to Fedora 13 and followed the "post-upgrade cleanup" instructions.Right now yum update is failing on the following error:Quote:
---> Package perl-Net-LibIDN.x86_64 0:0.12-3.fc13 set to be updated ---> Package perl-Net-SSLeay.x86_64 0:1.36-1.fc13 set to be updated kde/filelists_db | 1.0 MB 00:01 [code]....
-> retrieve install image, ok -> examine storage (or similar), ok -> transfer install image to disk, ok -> dependency check in install packages, ok -> start installation process, ok -> preparing to install
=> there was an error running yout transaction for the following reason(s): insufficient diskspace
you need more space on the following filesystems: 1089 M on unfortunately not more information displayed. only exit possible. Any experiences with this kind of behaviour? Many thanks for any feedback.
I am saddened that I can't install any Linux distro with ease on my HP m8530f computer which runs on a m2n78-la motherboard. It has a Phenom CPU, 6 SATA ports and probably a fakeRaid (at least that's what I guess is causing problem). The Fedora 14 Desktop install goes all the way to the end and then I get a fail message due to not being able to mount /dev/mapper/xxxxx.
P.S. the motherboard only has SATA mode or disabled for HardDrive mode and no any other options. Seems like this is an HP custom made motherboard from Asus hence the limited options in Bios setup.
Fedora-15-i386-DVD.iso file, sha256sum is correct. Burning by k3b on a fedora14 system fails again and again at 98.4% of the burning. I downloaded again to another partition and the same happens again. The k3b-debug output:
Im trying to install fedora 11 on my MacBook (Aluminum Series) but its not working.I turn on my mac...boot from the DVD...follow the instructions to install the fedora on my mac ( 3 partitions = [1-swap, 2-boot, 3-main]) and it installs normally, installs all the packages. When the installing is finished...it says click on reboot..When i do that, it seems like its rebooting...but the screen turns black for a long long long time that after a while im forced to manually turn off my mac. And when i turn it on...and see if the fedora is installed, There is nothing but my mac OS
After editing gdm and reming out line "auth required pam_suceed....................!=root quiet" the server boots but hang with the login screen. other highlighed but all options greyed out.
Boots OK in text mode and operates OK.
After restoring original gdm file problem still persists.
As I have no blank cds handy right now, I had to go the way descirbed here:URL...But when I seect my partition and / (no sub dirs, an empty ext3 formated 6.8GB partition, exclusivly for that usage) it tells me there ws no installation media found and the search path got automagically adjusted to /imges/image.img.And ideas howto fix that? Or how to install fedora from harddisk (without big fuss)?
When using the manual partitioner on the fedora 11 installer on the live cd, both for 64 bit and 32 bit, it will not allow me to create a new partition. I understand that I have four primary partitions and it cannot have more than that, so I tried deleting one of the partitions, then creating the new ext4 partition for F11. It still fails and gives me the same bugsee attachment)
how to read this, especially since there is so much there. I see at the top it says that there are 4 primary partitions, could it possibly still be seeing 4 primary partitions when trying to create the new one, even though I am deleting one of them? Other than this, I truly have no idea what else I can do.
EDIT: Attachment wont load up for some reason, here is some of the error file: anaconda 11.5.0.59-1.fc11 exception report Traceback (most recent call first): File "/usr/lib64/python2.6/site-packages/parted/disk.py", line 183, in addPartition constraint.getPedConstraint())
Anyone succeed with f11 install on netbook (/ on SDHC, /boot on primary SSD/HDD drive)? My netbook (AAO) works just fine with f11 Live-on-usb-sick (created with live-usb-creator), but fails to boot fedora from SDHC.
Fresh install of Fedora 11 x86_64, ext4 file system, Intel Quad, 1 Tb disk
Went through install, defined mike as user with password
reboot, get graphic login (init 5); cannot login as mike OR AS ROOT!! (unable to authenticate)
use live cd, reset inittab to start at level 3
reboot, get user prompt on terminal at level 3
enter mike and password, system wait a minute or more, returns to login prompt (obviously timing out --- dbus problem???)
enter root and password, get in, issue startx
open terminal window, and issue "su mike" command, ten minutes later, finally get terminal with mike as user.
Use ctrl-alt-F2 to get a terminal, type mike, and password, no joy; login as root and type "su mike". Go back to Gnome screen at F7, so I can continue to type this , and check back at F2 periodically to see if "su mike" ever takes. After three minutes, still no joy. After five minutes, it worked. whoami shows "mike"
I have sevral older machines that cannot boot from usb. Until now I have installed fedora using the provided boot.iso on a CD and an external USB dvd drive with the full install DVD.
With Fedora 11, this fails. It gets as far as "finding storage devices" and fails, telling me that an unhandled exception has occured. It offers to save the details, but freezes looking for a suitable location. I have no such problems with the same DVD/external rw drive on systems that can boot directly from usb.
I'm facing a problem installing Fedora 12 x64 on my desktop.I've been trying to get the Graphical Installer (anaconda) to run, in vain. The error message I get is reproduced below:
I'm currently running F11 and am trying to replace it with a fresh install of F13, using the same partitioning layout. I downloaded the F13 i386 DVD ISO using bit torrent. (The sha256sum of my downloaded ISO matches the reference sha256sum value.) I'm trying to do the fresh install of this ISO from hard drive (without burning a DVD). Last summer I did the same procedure of installing a downloaded DVD ISO from HDD when replacing F9 with F11. The installer (Anaconda 13.42) proceeds to the point where I specify my custom partitioning layout. It then prompts me about storing a boot loader. Shortly after I reply to that, the installer gets an "unhandled exception".
rpmdb: Program version 4.8 doesn't match environment version 4.7 error: db3 error (-30971) from dbenv -> open: DB_VERSION_MISMATCH
The only nonstandard thing I did was the following. According to the F13 installation guide, for installation from HDD the file "install.img" from within the ISO files must be copied to a directory named "images". The F13 installation guide gives the following procedure:
