I cant install or do to work the compiz...
my driver is Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
what can i do to have all effects and working fine?
My lap has a "Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03)" video card, and never took the 1280x800 resolution (that I had on windows). I searched a lot, and I installed a driver from the package manager (can't remember the name ...). Well, restart, and it's stuck at the finish of fedora loading process (a blank line).
I can access to the terminal (ctrl + alt + f2) and modify kernel parameters. By the way, on gnome I could't enter to "Desktop Effects" (it threw an message like "can't enter 3D Acceleration")
Can someone give me clues about adjusting my Ubuntu Lucid X11 use of my Intel video hardware? My laptop has video hardware identified as follows:( output from sudo lshw)
Code:
*-display:0 UNCLAIMED
description: VGA compatible controller
product: Mobile GM965/GL960 Integrated Graphics Controller
vendor: Intel Corporation
physical id: 2
bus info: pci@0000:00:02.0
[Code]...
Q3: The lshwoutput shows two displays, display:0 and display:1. Can someone tell me why two and how to make use of both of these? NOTE -- The existing forum entries are mostly from April 2009 or talk about Compiz issues. While Compiz will squeeze video hardware pretty well, I use a tablet-PC and so far, Compiz features do not play well with tablet features.
About a year ago, I installed ubuntu on my ThinkPad X61, which was running windows. I basically just overwrote the hard drive, assigning one partition to the install. The graphics have always been a little buggy when it comes to 3d rendering or flash. Flash graphics flicker a lot and 3d rendering leaves trails or doesn't show up at all. Is there a way to configure the graphics card? I'm completely unexperienced when it comes to graphics cards and don't know where to start. I don't even know how to access its settings.
View 1 Replies View RelatedI have a problem with compiz and this card, after few weeks suddenly it doesn't work with ubuntu, I always had troubles with this kind of cards, I was always able to solve it by this forum but this time I gave up.
The driver for GM965/GL960 is working perfectly but the compiz effects although they are enabled they are not applied to the desktop environment.
The compiz-check output is:
Code:
Gathering information about your system...
Distribution: Ubuntu 11.04
Desktop environment: GNOME
Graphics chip: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 03)
Driver in use: fbdev
[Code]...
I have a fairly new laptop, 2*1.8 Ghz, but when I try to run games more advanced than pac-man, it's about 1-0.5 frames / second. This doesn't seem right. I've goggled it, and found a few posts from 2008-2009, but nothing that actually helped. Does anyone have any idea, as to what might be wrong? If anyone has this card, I'd like to see what you have in your /etc/X11/xorg.conf file...
@art:~$ lspci -nn | grep VGA
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a02] (rev 03)
I just upgraded to 10.4 lts, and compiz stoped working. EDIT: lspci | grep VGA gives me:
Code:
00:02.0 VGA compatible controller:
Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03)
If I try to run it from terminal i get:
Code:
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
[Code]...
My lap has a "Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03)" video card, and never took the 1280x800 resolution (that I had on windows). I searched a lot, and I installed a driver from the package manager (can't remember the name ...). Well, restart, and it's stuck at the finish of fedora loading process (a blank line). I can access to the terminal (ctrl + alt + f2) and modify kernel parameters. By the way, on gnome I could't enter to "Desktop Effects" (it threw an message like "can't enter 3D Acceleration")
View 1 Replies View RelatedDoes vaapi support the intel gm965 video card?
View 6 Replies View RelatedI have had to install the B43 diver before to get wireless to work.
View 5 Replies View Relatedi just installed centos on my dell inspiron 1525 but the network driver doesn't recognized
View 8 Replies View Relatedi have installed red hat 5.1 on my dell inspiron 1525 laptop.It is not detecting any ethernet card.driver is marvel yukon 88E8040So far i found this package to be installed kmod-sk98lin-PAE-10.70.7.3-2.el5.elrepo.i686.rpm but it is showing me the dependencies problems..
View 4 Replies View RelatedI have been using Ubuntu since September of last year (2010) I haven't realized it, but my mic isn't working. I'm am not entirely sure what type of mic I have, but the output of "lspci" are as follows:
Code:
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
[Code]....
Wilreless network disconnected ...
in Dell inspiron 1525
I'm on a Dell Inspiron 1525 running Arch Linux with an Intel 965 GM video chipset (from dmesg). I'm using the xf86-video-intel driver, and Xorg (using xfce4) works flawlessly, including compositing. Before getting into details about the HDMI, I'd like to ask why I don't gave an xorg.conf.d/10-moniter.conf, it's not there, just evdev, quirks, and synaptics (because I figured that moniter.conf could be modified to include HDMI). So, basically when I'm on my XFCE4 desktop, I plug in the HDMI cable and to the TV, and on windows, it would would work, but on Arch the TV just says: "No input", and my desktop just stays the same, so absolutely nothing happens. If I have it connected upon bootup, the HDMI displays (the BIOS and grub menu on the TV) until I select to boot Arch linux on Grub, then the tv screen goes blank. I've tried Googling this but I got no decent results, just a bunch of random posts of audio not working with Nvidia.
PS - I did dmesg and lspci (with grep HDMI) and no results, so maybe it doesn't even recognize it, but then what do I do? There's obviously Linux support for HDMI...
When trying to install Lucid on my HP Compaq 6710b (INTEL Mobile GM965/960 graphic controller) using the alternate i386cd with an usb pen i (re-)experiencing (known from the Jaunty installation) the following problem:Boot from USB (works) Select language (works) Choose to install ubuntu (works) Removing quit from the boot options, hit enter, see some output (works) Starting the installation interface (fail) The screen wents to black, but system seems not froozen. What i've tried to fix this issue:fb=false as bootoption (worked in jaunty, does not work with lucid) frambuffer=false
fb=off
debian-installer/framebuffer=false
vga=123, tried all of the offered modes
vga=771 (get some screwed up output on the screen, which i guess from that the system/machine is not frozen)
i915.modeset=1
i915.modeset=0
xforcevesa etc
Anyone managed to install Lucids with INTEL graphics + the alternate cd? PS: I need the alternate cd to setup an encrypted system. PPS: Just tested the desktop i386 image which works flawlessly.
I used wubi to install 9.10 on my dell inspiron 1525. I had a problem with not being able to get wireless working, and found out that I had to activate the Broadcom STA driver which lead to a crash. Now I've rebooted, everytime I try to install I get 'SystemError() InstallArchives' or the authenticate box hangs. Is there another way to install these drivers?
View 1 Replies View RelatedI have a dell inspiron 1525 and installed Virtualbox 3.2.6 and installed Ubuntu 10.04 on a VM. The installers went fine. After updating and installing the guest additions and also installing compiz-setting-manager i'm still not able to get the compiz effects. please any suggestions .
View 8 Replies View RelatedI will say this now; I am still in high school, so forgive my stupidity. I am trying to install either 10.10 or 10.04 on a Dell 1525. It has no operating system on it, and the CD/DVD drive is nonexistent. I have tried to install 10.10 on it using a USB, with both UNetbootin and Pen Drive Linux. Using either one, both end up freezing at the "Preparing to Install" screen. When trying to install 10.04, it will not load, even after 24 hours. On the loading screen, I pressed F1 to view the terminal and got this output:
(process:352): GLib-WARNING **: getpwuid_r(): failed due to unknown user id (0)
Killed
I got all downloads from their home websites, www.ubuntu.com, www.pendrivelinux.com, and www.unetbootin.sourceforge.net. I have spent all my spare time since the newest release trying to fix whatever problem there is, so does anyone know what I did wrong?
Recently I got an hp pavilion g4-1016tx laptop, I installed Fedora 15on it, I chose the "install with basic video driver" option, first it workedwell, but yesterday I could only log in with text mode.There are two videocards on my laptop: AMD Radeon HD 6470M Intel GMA HDI tried to install the ATI driver on my laptop, and I still failed to makeit work properly.My error messages are as follows:
# aticonfig --initial
aticonfig: No supported adapters detected
# fglrxinfo
[code]....
I have a problem with my laptop Dell Inspiron 1525 wireless on Jessie Cinnamon.
I have installed the b43 firmware and after that everything seemed working but just for a few seconds.
I have tried to reboot and after that I can't browse the internet just for a few seconds and after that Iceweasel loading and loading and nothing's happening.
I can't surf on the net just with cable but the wifi setup shows everything is okay 95% signal strength and connected.
Also tried reinstall the firmware and reboot and it's all the same after.
I can easily use my wifi with my smartphone too.
I have dell inspiron 1525.I installed Redhat linux 5.2 and then Oralce 10g R2.I can not start Oracle enterprise manager(EM) on redhat.Except EM oracle is working properly.Why is so ?
View 2 Replies View RelatedI've been using slackware64 13.1 ever since it came out on my Dell Inspiron 1525, and I haven't really had any problems with my webcam in that time. However, last time I tried to use skype - I noticed that it couldn't detect it.
In kinfocenter, my webcam is picked up (OmniVision Technologies). The only time I've had a similar problem in the past is when I used the "Compact" option in lilo.conf, and the webcam wouldn't turn on. Just removing the option solved the problem.
Since I don't know what steps caused this to happen, I'm not sure where to start fixing it
Host: CentOS 5.4 x32
Guest: FC12 x32
Virtual machine: Virtual Box (VBox) 3.1.4
The 640 x 480 video display on my FC12 guest is driving me nuts! The VBox Guest Additions are installed. How do I get FC12 to recognize the VBox video driver?
Extra information:
Auto resize works great on my Windows guests. On FC12, I just get a lot of extra white space.
FC12's installer does not detect a video card. You have to use the stand display option (second one down) to get FC12 to go into a full graphical installer. If you use the regular install, hoping to do a graphical install, FC 12 only install the bare basics. No video support. You get what looks like a rescue cd. No Gnone, no X etc.
I do believe that FC12 has no idea that the VBox's fake video adapter even exists.
Somehow my video driver got deleted and now all i can access is a terminal and no gui. how do i reinstall my video driver?
View 3 Replies View RelatedI have a Asus 54G43-Pro mobo with Intel GMA G43 video chip on it. It works fine in Ubuntu and using the same display with the same settings, under Maverick in comparison with Lucid, the video is a little more sharp and with more contrast. I have dual boot with Windows and in Windows it is even less sharp and contrast.
In Windows I can tune the sharpness, contrast, etc but I was not able to find a simlar features in Ubuntu. I have checked the Synaptic and even installed some Intel GMA files but I still have no access on tuning the video driver. Is this possible in Ubuntu and possible to be hidden somewhere or I can just forget about it?
I have a Dell Inspiron 1525 laptop and I ve installed Jessie with KDE desktop.Everything's fine !!!!! but sometimes when I use webbrowsers the systray with KDE menustart is going off and missing.After that I can't switch window to window and can't minimize or resize the actual activity, without or with hotkeys either can't close the window, and these option bars ar missing too.I always do restart but I ve had enough. It is very irritating.Also I have tried to switch user logons with Alt Ctrl Fxx and start another graphic array with startx and it has worked fine but that's not the right way I think!!!!
View 11 Replies View RelatedI am trying to use JACK for some audio applications, but I have had no success until now I'am using Ubuntu 10.04 on my Dell Inspiron 6400. Kernel 2.6.32-33.
The following is the QjackCtl log:
p, li { white-space: pre-wrap; } 14:38:48.196 Steckfeld deaktiviert.
14:38:48.377 Statistik zurckgesetzt.
[code]....
I'm trying to run/use the Intel GMA 4500 on my Debian Linux (Lenny), but I'm having some problems. I just can't find the drivers and the default installation does not install the correct driver.
View 3 Replies View RelatedI am wondering, what is the status of Intel GMA X4500 driver on Fedora 10.
View 2 Replies View Related