Fedora Hardware :: Broadcom 4312 Freezes F12 / Fix It?
Feb 18, 2010
I've been having some trouble with my recently bought laptop.
Type: Dell Vostro 1015.
You can see the full specification by following the link in my signature.
What's important is this code..
The system freezes randomly and all I can do is to push the power button and force-turn it off.
I'm not sure, but I think it's the wireless. It's my second Fedora install on this machine, and the second was all right until I set the wireless drivers (or I had luck to have no stops).
View 6 Replies
ADVERTISEMENT
Nov 23, 2009
How do you enable repos? Namely RPMFusion set? I have 2 repo's that are currently in stalled:
[root@dv5-1235 Joe]# yum repolist
Loaded plugins: presto, refresh-packagekit
repo id repo name status
fedora Fedora 12 - x86_64 enabled: 19,122
updates Fedora 12 - x86_64 - Updates enabled: 755
repolist: 19,877
I'm trying to get my Broadcom 4312 working again since FC10. I noticed that RPMFusion isn't listed. This would answer why I can not install Broadcom -wl.
View 4 Replies
View Related
Feb 11, 2010
The card uses a momentary switch to turn on at and off and it doesn't work. I read that there is a way to have the card turn on by default on boot but I can't figure out how to do it.
View 1 Replies
View Related
Mar 6, 2010
After some serious trouble with Plasma, I decided to re-install 9.10. When booting up, I noticed that the wireless indicator light stayed on orange which usually means that the driver is not loaded.
I have a Broadcom 4312 in a HP Pavilion dv6. I checked the repository but no driver shows up. I seem to remember that it used to be there. Or am I mistaken and do I need to install the vendor driver from the Broadcom site?
I've added the output of lspci and dmesg | gre b43
HTML Code:
HTML Code:
View 3 Replies
View Related
Aug 23, 2010
Well I see there is a lot of people which have problems with BCM4312 I read that topics but my problem kind of different..I installed 11.3 few day ago at my job. Everything was just fine...First of all I'm installed firmware
Code:
install_bcm43xx_firmware
Wireless worked fine...
[code]...
View 9 Replies
View Related
Mar 13, 2010
I'm finding a hard time getting my wireless card to work, my laptop is a Dell Inspiron 1525 and this is all the info:
0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
0b:00.0 0280: 14e4:4315 (rev 01)
[ 8.375610] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
[ 8.390374] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 6, Type 5, Revision 1)
[ 8.390436] b43: probe of ssb0:0 failed with error -95
View 9 Replies
View Related
Oct 31, 2010
I'm reinstalling opensuse 11.3 with KDE. In previous setup I got it working. It is a fresh x64 install. Update all is done. Pacman repo added. code...
View 4 Replies
View Related
Mar 10, 2011
Wifi works on 11.3 with installed the broadcom-wi & broadcom-wl-kmp-desktop,but this trick doesn't work on this new 11.4.
View 9 Replies
View Related
Jun 11, 2010
I have an HP 2133 Mini-Note [KX869AT] with a Broadcom 4312 wireless card. I've had Ubuntu 10.04 on my machine for a few weeks now and everything was great until my wireless card abruptly stopped working. It doesn't detect any wireless networks,uch less connect to them. I tried reinstalling the proprietary driver, but that hasn't worked.
View 1 Replies
View Related
Jun 23, 2010
When I first had partitioned, and formatted appropriately, I installed the newest version of Ubuntu available (Time of posting 10.4), on the partition made with bootcamp, rebooted into Linux with rEFIt Now once I booted into 10.4 I got to the desktop, it started asking me about restricted hardware drivers, so I went into System > Administration > Hardware Drivers, It then searched for the drivers, it found the STA driver, and the B43 driver, I am unable to allow both. So I went on to try ndiswrapper, I downloaded it off another pc, compiled and installed on the iMac. then I got the driver off the Leopard install disk, put that on my flash drive, extracted the files from the installer, put that on the flash drive, then I went back over to the machine in question, copied the file to the desktop, I used the cd command to navigate to the folder, then ran ndiswrapper -i bmcwl6.inf, I made sure that the inf and sys files were in there, so I didn't know what was going on exactly.
So then I went into the software sources, and enabled the cd as a software source, then went into Synaptic, and installed the drivers, it said the install was successful, however when I go back to enable it, will still refuse to activate, I have looked all around for solutions, I have even checked out other threads on this matter. The funny thing seems to be, is that everyone, or almost everyone who has this card on their computer, are upgrading to 10.04, when it worked on a previous version.
View 4 Replies
View Related
Jul 17, 2010
after finally installing 11.3, I found that my wireless NIC had stopped working. I've spent about 4 hours trying various online tutorials to get the card working, but I'm still right where I was when I began. The card as reported by lspci:
[Code]....
View 9 Replies
View Related
May 9, 2010
I've already got the b43-fwcutter package and a driver called 'b43' appears in System > Administration > Hardware Drivers but it does not seem to enable. Another, Broadcom STA wireless driver, does enable, but I'm not picking up the wireless signal.
Code:
$lspci 05:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 01)
08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Code:
$ sudo lshw -C network
SCSI
[Code]...
View 5 Replies
View Related
Jun 1, 2010
I've been stalking the forums for the past few days trying various fixes to no avail. I'm sorry for more clutter of this issue.
Here's what I have:
emachines e725 laptop, dual core T4400 Pentium, 64bit, running Windows 7 and just installed Ubuntu 10.04.
My ethernet port works for cat internet but wireless does not. My wireless appears but when I open browser no connection.
Here is my ifconfig:
View 9 Replies
View Related
Oct 25, 2010
i just got ubuntu yesterday and had to play around with some settings and the fw-cutter tool to get my wireless working and it was...although i upgraded the kernel to 2.6.32-25-eneric...and it stopped working. the simple solution is to use the previous kernelersion...the wireless works there, but thats just not good enough for me ... it recognizes my card is there it just wont connect. originally i was using b43 driver and now it does not show in the system>hardware drivers list only the sta driver does, although when i try to install and activate it i get the error message "sorry, installation of this driver failed.please have a look at the log file for details: /var/log/jockey.log"
View 5 Replies
View Related
Jan 2, 2011
I have a DEll Mini 9 - it has worked fine even though it has a limited memory. But Husband only uses to have a surf. It now wont connect to net. The Broadcom4312 Wireless Card is not working on Obunto. It has a Dell 802.11b/g Wireless LAN Mini card installed and Obunto Edition Version 8.04 Have phoned Dell and after several calls on Hold for over 15 mins each time and getting nowhere fast i am coming to you guys/girls. I am not a very good comp person, but i do get by and i am trying, so be gentle with me. in simplistic terms.
View 2 Replies
View Related
Jan 8, 2011
I just put 10.10 on my D830 and I love it except for a delay when I'm using the internet. When I click on a link while surfing the web it takes about 13 seconds before it responds. After that it works just fine.
My Windows 7 PC and my Macbook Pro don't do that so I'm guessing it has something to do with Ubuntu.
View 5 Replies
View Related
Jan 20, 2011
I have installed CentOS 5 just downloaded yesterday on a Dell D620. Everything but the wireless card works. So I found this article:
http://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom
and followed it step by step and was able to complete all of the tasks. The problem is that obviously it still won't start. It is not even recognized as an adapter but when I run lspci -v it is there sure enough. When I look under the networking GUI it is listed there but it has no MAC assigned to it. Please let me know what command output you need to see and I'll get here asap. I have searched this forum and other sites and nothing so far has worked.
View 1 Replies
View Related
Jul 16, 2010
Im having problems making my wireless card "Broadcom 4312" work on centos 5.4 X64 , i have installed and built the driver from their official site and inserted its module successfully, but whenever i try to avtivate the interface "called eth1" i get the following
Error for wireless request "Set Encode" (8B2A) :
SET failed on device eth1 ; Invalid argument.
Error for wireless request "Set Encode" (8B2A) :
SET failed on device eth1 ; Invalid argument.
View 2 Replies
View Related
Oct 23, 2009
I got a new laptop and installed Fedora 11, but I can't get the wireless working. I run lspci, it shows "Broadcom Corporation BCM4312 802.11b/g (rev 01)", so I believe the wireless card is there.I went over the thread URL... which explains in detail how to get BCM4312 working. I installed the b43 driver and the reboot. However, when I left click the NetworkManager, the only thing pops up is "Wired Network", "system eth0" and "VPN configurations". Nothing about "wireless" in there. Does this mean that the wireless driver is not installed at all? And the Network Configuration only has eth0 device.
I then tried to install broadcom-wl, but it complains there is conflict between b43 and broadcom-wl.I also tried to install the driver from autoten, it fails also.
View 10 Replies
View Related
Jun 27, 2011
We are having a cluster with couple of disk servers, compute nodes and a head node. Disk server is nfs mounted on all the compute and head nodes.
The problem is that if any of the disk servers hangs, it freezes rest of the cluster too which is dangerous. Ideally, cluster should not care about the hanged server and run without any problem except files from that server is not visible.
Is there any way I could avoid the problem of freezing cluster because of one hanged server?
View 1 Replies
View Related
Feb 21, 2011
I am attempting to iron out a detail that has been bugging me a long time.Does the procedure of providing the firmware during install actually work? Note: I am NOT asking how to install the firmware POST install. What I have done to attempt to resolve:
1. Searched forums with no luck on this specific question.
2. Google was likewise uninformative.
Steps performed:During the wheezy install, from cd (cd1 testing amd64, appx 680MB), it prompts for firmware, which it identifies as ucode15.fw. (This is only part of the file name, as I did not write the entire bit down during the install.)
View 13 Replies
View Related
Feb 2, 2010
1 ) Machine Brand and Model (PC/Laptop):
Quote:
Dell XPS 1330.
2 ) Wireless Brand, Model and Wireless Chipset:
Quote:
0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
Bus 002 Device 004: ID 05a9:7670 OmniVision Technologies, Inc. OV7670 Webcam
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[Code]....
At this point, I have installed the STA driver for the device, though I have also tried with B43 (fwcutter). I have also tried with ndiswrapper with windows driver. All these cases, the end effect is the same.
I can see "Wi-fi" LED light up. When I bring up the KDE control module for networks, "Wireless" is disabled. However, when I right-click on the network manager icon on the taskbar, I see "Enable Wireless" checked on.
I am wondering if in the process of installing the ndiswrapprer drivers, I am messed up something?
View 5 Replies
View Related
Aug 26, 2009
Okay I posted about this a while ago, and i got my wired network to work, but now i need my wireless card driver to work. I have been doing research and I found something called ndiswrapper which drivers from windows working in linux. I typed in lspci in the terminal and it gave me my specs of my wireless card which is a:
-Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03)
-Some people said there is no original driver for this card, so you need to use ndiswrapper, I was wondering does anybody know what this is, how do i use this, and help me out to get my wireless card going. If you give me instructions, please be really specific as I am really new and still getting the hang of commands.
View 1 Replies
View Related
Feb 4, 2010
Last update: 8/25/2011 Table of Contents
Introduction
Step 1: Identify the chipset of the wireless device
Step 2: Choose the right driver
Step 3: Install the driver
How to install and use b43 and b43legacy How to install and use the Broadcom 802.11 Linux STA driver (broadcom-wl) How to install and use b43-openfwwf
[Code]...
View 14 Replies
View Related
Aug 2, 2009
Got up this morning and switched on theLinux Box and started getting wifi connect problems. I could work for about 5 mins then it would start searching and asking me to confirm to connect to my network.After some time NM kept on asking all the time to confirm the network and key.I reset the router and check to see if other PCs were OK and a Windoze & Linux laptops were fine, no problem there so it's not the routerd.I'm wondering if the broadcomm card is starting to fail as it heats up or could it be a corrupt file or parametersNo updates have been done in the last month, it just started today. Here are the results from the log and dmesg:
[root@mylinux ~]# dmesg | grep b43
b43-pci-bridge 0000:05:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
b43-phy0: Broadcom 4306 WLAN found
[code]...
View 10 Replies
View Related
Aug 9, 2011
How to install and use the Broadcom 802.11 Linux STA driver (broadcom-wl) I orginally had wireless but reinstalled Fedora 15 and have been trying for days to get it working with no success
lspci
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge (rev 02)
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller (rev 02)
[code]....
how to use Fedora - how I fluked it the first time - but havent had any luck since reinstall
View 8 Replies
View Related
Jul 11, 2009
I have a Dell-made, Broadcom-based wireless card, BCM4322. I'm using Broadcom's proprietary drivers from RPM Fusion.
Code:
lspci | grep -i broadcom
09:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe (rev 10)
0c:00.0 Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01)
Since installing F11, I can no longer connect to WEP-secured wireless. When I use automatic IP settings, the connection simply times out. When I specify an IP, Netmask, Gateway, and DNS server, NetworkManager thinks the connection properly established, but any pings time out, even when I don't specify a hostname (just an IP address). I can connect to (and use) unencrypted wireless. I haven't tried other encryption schemes. The WEP index is 1 and it's non-authenticated (open). I've been playing with the settings for over a week now with no success.
View 6 Replies
View Related
Jul 16, 2009
My F11 x86_64 machine has regularly been crashing at boot up. I removed broadcom-wl and installed ndiswrapper, now the crashes seem to have gone.
I wonder if anyone else has noticed issues, I have this Broadcom wireless model:
0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
View 3 Replies
View Related
Sep 7, 2009
there was a new kernel update that I installed today. I used some kl mod packages to work my broadcom. For some reason its not working after the kernel. Is there a way I can recompile the driver or so?
View 7 Replies
View Related
Nov 18, 2009
I have an issue, this issue to be exact: [URL]. My broadcom BCM57780 is not detected. I just download Fedora 12 today and was happy to get it up and running. The bug report says it was fixed in f11, but it does not appear to be working in F12 either. I tried both the i686 and x64 live cd's and neither find the Ethernet adapter. I would really love to get my new computer up and running without having to buy another Ethernet card to do so.
View 5 Replies
View Related
