After some serious trouble with Plasma, I decided to re-install 9.10. When booting up, I noticed that the wireless indicator light stayed on orange which usually means that the driver is not loaded.
I have a Broadcom 4312 in a HP Pavilion dv6. I checked the repository but no driver shows up. I seem to remember that it used to be there. Or am I mistaken and do I need to install the vendor driver from the Broadcom site?
I've added the output of lspci and dmesg | gre b43
I have a DEll Mini 9 - it has worked fine even though it has a limited memory. But Husband only uses to have a surf. It now wont connect to net. The Broadcom4312 Wireless Card is not working on Obunto. It has a Dell 802.11b/g Wireless LAN Mini card installed and Obunto Edition Version 8.04 Have phoned Dell and after several calls on Hold for over 15 mins each time and getting nowhere fast i am coming to you guys/girls. I am not a very good comp person, but i do get by and i am trying, so be gentle with me. in simplistic terms.
When I first had partitioned, and formatted appropriately, I installed the newest version of Ubuntu available (Time of posting 10.4), on the partition made with bootcamp, rebooted into Linux with rEFIt Now once I booted into 10.4 I got to the desktop, it started asking me about restricted hardware drivers, so I went into System > Administration > Hardware Drivers, It then searched for the drivers, it found the STA driver, and the B43 driver, I am unable to allow both. So I went on to try ndiswrapper, I downloaded it off another pc, compiled and installed on the iMac. then I got the driver off the Leopard install disk, put that on my flash drive, extracted the files from the installer, put that on the flash drive, then I went back over to the machine in question, copied the file to the desktop, I used the cd command to navigate to the folder, then ran ndiswrapper -i bmcwl6.inf, I made sure that the inf and sys files were in there, so I didn't know what was going on exactly.
So then I went into the software sources, and enabled the cd as a software source, then went into Synaptic, and installed the drivers, it said the install was successful, however when I go back to enable it, will still refuse to activate, I have looked all around for solutions, I have even checked out other threads on this matter. The funny thing seems to be, is that everyone, or almost everyone who has this card on their computer, are upgrading to 10.04, when it worked on a previous version.
Well I see there is a lot of people which have problems with BCM4312 I read that topics but my problem kind of different..I installed 11.3 few day ago at my job. Everything was just fine...First of all I'm installed firmware
Code: install_bcm43xx_firmware Wireless worked fine...
I'm finding a hard time getting my wireless card to work, my laptop is a Dell Inspiron 1525 and this is all the info: 0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) 0b:00.0 0280: 14e4:4315 (rev 01) [ 8.375610] b43-phy0: Broadcom 4312 WLAN found (core revision 15) [ 8.390374] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 6, Type 5, Revision 1) [ 8.390436] b43: probe of ssb0:0 failed with error -95
after finally installing 11.3, I found that my wireless NIC had stopped working. I've spent about 4 hours trying various online tutorials to get the card working, but I'm still right where I was when I began. The card as reported by lspci:
I have an HP 2133 Mini-Note [KX869AT] with a Broadcom 4312 wireless card. I've had Ubuntu 10.04 on my machine for a few weeks now and everything was great until my wireless card abruptly stopped working. It doesn't detect any wireless networks,uch less connect to them. I tried reinstalling the proprietary driver, but that hasn't worked.
I've already got the b43-fwcutter package and a driver called 'b43' appears in System > Administration > Hardware Drivers but it does not seem to enable. Another, Broadcom STA wireless driver, does enable, but I'm not picking up the wireless signal.
i just got ubuntu yesterday and had to play around with some settings and the fw-cutter tool to get my wireless working and it was...although i upgraded the kernel to 2.6.32-25-eneric...and it stopped working. the simple solution is to use the previous kernelersion...the wireless works there, but thats just not good enough for me ... it recognizes my card is there it just wont connect. originally i was using b43 driver and now it does not show in the system>hardware drivers list only the sta driver does, although when i try to install and activate it i get the error message "sorry, installation of this driver failed.please have a look at the log file for details: /var/log/jockey.log"
I just put 10.10 on my D830 and I love it except for a delay when I'm using the internet. When I click on a link while surfing the web it takes about 13 seconds before it responds. After that it works just fine.
My Windows 7 PC and my Macbook Pro don't do that so I'm guessing it has something to do with Ubuntu.
I have installed CentOS 5 just downloaded yesterday on a Dell D620. Everything but the wireless card works. So I found this article: http://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom and followed it step by step and was able to complete all of the tasks. The problem is that obviously it still won't start. It is not even recognized as an adapter but when I run lspci -v it is there sure enough. When I look under the networking GUI it is listed there but it has no MAC assigned to it. Please let me know what command output you need to see and I'll get here asap. I have searched this forum and other sites and nothing so far has worked.
I am running FC13 on a Compaq Presario 2100 using a Broadcom BCM4306. I was able to get it running thanks to Fedora Unity Project. But It's a very unstable connection. I don't know what settings to adjust or enable or disable. It's not my router, this is the only wireless connection in the house that I have trouble with.
I'm having some problems with my wireless connection. I'm on Ubuntu 10.04, on a HP ProBook 4520s, with a RaLink RT3090 wireless network card. I installed the drivers (hopefully correctly), the wireless seems to work correctly, it scans and finds networks, but when I try to connect to one, it times out after some time, while still attempting to connect. I also have a wired connection that works correctly and without problems. Other computers that try to connect to said wireless network manage to do so without any problems, so this has left me a bit baffled, since, like I said, everything seems to be in order.
I'm a new Ubuntu user, so please tell me what other information I need to provide in order to easily and successfully facilitate troubleshooting this, because it is, as you can imagine, quite aggravating, having a laptop that needs to be connected to the internet through a cable.
I have installed the driver of my Broadcom Wireless card BCM4312 ( Acer extenza 5620 laptop) and when i try to connect to my wireless connection it just try to connect for a while and then go offline i tested another usb wireless card and still no success
My HP Pavilion dm4 notebook has the Broadcom bcm4313 and worked with the proprietary Broadcom driver provided with Ubuntu 10.04 but did not work with the corresponding driver provided with Ubuntu 10.10. The solution that worked for me (for a while) was to install "broadcom-sta-common" and its dependencies using Synaptic. After enabling the proprietary driver (System > Administration > Additional Drivers) and rebooting, wireless worked. I even shared this on this post. chargersfan420 get his Broadcom card functional again.
What changed to break it? Well, wireless had worked for several days, so I felt that I had solved the wireless problem. Now it was time to find a solution to unlock my BIOS settings. I successfully used PCCMOSCleaner to clear the password. After that, no more wireless. (Note to dm4 users: Apparently HP puts a password on the BIOS settings and makes it available only if you boot into the factory-installed Windows 7 and retrieve it. Of course I never booted into Windows 7 before upgrading the machine to Linux, deleting both the Windows partition and HP's hidden recovery partition.)
I uninstalled all the Broadcom stuff and reinstalled it all. Now I appear to have wl working, and b43 and ssb blacklisted, but network manager is not seeing any wireless connections available.
My Hardware: HP Pavilion dm4-1063cl My OS: Ubuntu 10.10 32-bit (clean install)
So basically, complete linux noob here, dual-booted fedora 13 with windows 7, and fedora can't seem to detect either my wired or wireless, however i don't really care about the wired. After spending a few hours browsing forums and tutorials and the like, seems as if it is a driver issue, as in there is none. I have managed to find the files :
HTML Code: broadcom-wl-5.60.48.36-1.fc13.noarch.rpm kmod-wl-5.60.48.36-1.fc13.5.x86_64.rpm
I have a very strange problem with Fedora 12 and my wireless Broadcom 4311 card.After the installation of Fedora 12 the wireless card was visible but not activated. I did an extensive search in Internet and finally I got everything done. The card was visible and activated. I found my home network; the strength of the signal was nearly 100%.The problem is that although the card is visible and activated my browser is not working well. I can say that it is not working at all. Even now I am using other computer to write this message because Firefox cannot load any web page at all.
The strange part of the problem comes with the fact that when I open terminal window and when I am using yum everything looks OK. The speed is very low though.Does anybody have some ideas about the problem and its solution?When I use Windows on the very same computer everything is fine, the Internet speed is close to the maximum limits of my provider's speed which is 10 mbps.
The card uses a momentary switch to turn on at and off and it doesn't work. I read that there is a way to have the card turn on by default on boot but I can't figure out how to do it.
I got a new laptop and installed Fedora 11, but I can't get the wireless working. I run lspci, it shows "Broadcom Corporation BCM4312 802.11b/g (rev 01)", so I believe the wireless card is there.I went over the thread URL... which explains in detail how to get BCM4312 working. I installed the b43 driver and the reboot. However, when I left click the NetworkManager, the only thing pops up is "Wired Network", "system eth0" and "VPN configurations". Nothing about "wireless" in there. Does this mean that the wireless driver is not installed at all? And the Network Configuration only has eth0 device.
I then tried to install broadcom-wl, but it complains there is conflict between b43 and broadcom-wl.I also tried to install the driver from autoten, it fails also.
I'm trying to get my Broadcom 4312 working again since FC10. I noticed that RPMFusion isn't listed. This would answer why I can not install Broadcom -wl.
I've been having some trouble with my recently bought laptop. Type: Dell Vostro 1015. You can see the full specification by following the link in my signature.
What's important is this code..
The system freezes randomly and all I can do is to push the power button and force-turn it off.
I'm not sure, but I think it's the wireless. It's my second Fedora install on this machine, and the second was all right until I set the wireless drivers (or I had luck to have no stops).
0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) Bus 002 Device 004: ID 05a9:7670 OmniVision Technologies, Inc. OV7670 Webcam Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[Code]....
At this point, I have installed the STA driver for the device, though I have also tried with B43 (fwcutter). I have also tried with ndiswrapper with windows driver. All these cases, the end effect is the same.
I can see "Wi-fi" LED light up. When I bring up the KDE control module for networks, "Wireless" is disabled. However, when I right-click on the network manager icon on the taskbar, I see "Enable Wireless" checked on.
I am wondering if in the process of installing the ndiswrapprer drivers, I am messed up something?
Im having problems making my wireless card "Broadcom 4312" work on centos 5.4 X64 , i have installed and built the driver from their official site and inserted its module successfully, but whenever i try to avtivate the interface "called eth1" i get the following
Error for wireless request "Set Encode" (8B2A) : SET failed on device eth1 ; Invalid argument. Error for wireless request "Set Encode" (8B2A) : SET failed on device eth1 ; Invalid argument.
I've an network architecture where for the user to reach the machine that it want, it has to pass through a frontend machine.
Code: User ---> Frontend ----> Machine1
The connections between all hosts uses ssh. If I want to reach the Machine1, I've to authenticate to the Frontend and authenticate again to the Machine1. The Machine1 and the Frontend doesn't have X installed - only console mode.
The Machine1 has the file in my HOME directory called: hello.html that contains flash embedded. I would like to view the hello.html in my browser located at the User machine.
Is there a way to access remotely to the html file, without have to copy the file to my local machine?
I am running opensuse 11.2 on my hp 2133 mini notebook, I have been having trouble connecting my broadcom 43xx internal wireless modem to my BT Home Hub, I have looked at the b43 driver that comes pre-bundled with the live dvd and understand that the driver doesnt work, I have looked at the YaST Package Search and to my horror found 50 seperate packages, from: wl-kmp desktop - wireless driver for broadcom 43xx series of chips to sta-pae kernal for 43xx series of chips? How do i know which Kernal and driver i need to get my wireless network running and which i dont?
I've been running Karmic since it was officially released on my Dell Studio 17 (specs are in my signature) with a Broadcom wireless half mini wireless card.hen I installed Karmic, it gave me the option to install proprietary drivers for my video card as well as 2 Broadcom drivers, STA and one of the BC43 drivers. I installed all of these, and the only problems I had were with the audio. I spent a few days troubleshooting the audio and finally got PulseAudio set up for my card.
Almost 3 months later, I was making use of my wireless network at home, as I had done plenty of times over the previous 3 months, when I closed the lid (thus putting the computer into sleep mode) and took it to the hospital to stay with my fiancé¥ after her surgery. When I got to the hospital, I couldn't get their network to show up. Network Manager didn't even recognize the network. We had also brought my fianc饧s laptop (same machine with a slightly less powerful CPU and only 4 GB of RAM). She is running Windows 7, which detected the hospital's network with no problems.After trying to ad-hoc the hospital network with no success, I finally just gave up and played Sudoku and toyed with some graphics stuff in GIMP until we came home. Upon returning home, however, I was shocked that my card didn't even detect our home network.
I have been unsuccessful for the past 3 days in getting Network Manager to identify our wireless network. The wired network connects without issue and I am able to make use of a USB Belkin adapter, which identifies all 7 of the various wireless networks in my neighborhood, including our home network.While I would be able to simply carry my Belkin adapter with me in order to make use of wireless networks, I would really like to solve this problem with my Broadcom adapter. I've gone through the Ubuntu Wireless Network Troubleshooting guide, but I still can't get it to workOutput of lshw -C network:
