Ubuntu Networking :: XPS 1330 Broadcomm 4312 With 9.10 - Wireless Not Enabled
Feb 2, 2010
1 ) Machine Brand and Model (PC/Laptop):
Quote:
Dell XPS 1330.
2 ) Wireless Brand, Model and Wireless Chipset:
Quote:
0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
Bus 002 Device 004: ID 05a9:7670 OmniVision Technologies, Inc. OV7670 Webcam
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[Code]....
At this point, I have installed the STA driver for the device, though I have also tried with B43 (fwcutter). I have also tried with ndiswrapper with windows driver. All these cases, the end effect is the same.
I can see "Wi-fi" LED light up. When I bring up the KDE control module for networks, "Wireless" is disabled. However, when I right-click on the network manager icon on the taskbar, I see "Enable Wireless" checked on.
I am wondering if in the process of installing the ndiswrapprer drivers, I am messed up something?
View 5 Replies
ADVERTISEMENT
Oct 1, 2010
I had Ubuntu 8.04 and the D-Link Wireless WNA-1330 PCMCIA card worked just fine. I upgraded to 10.04 and it fails. I can see the network of wireless routers in my neighborhood, but when I try to connect on WEP 40/128bit with my hex key of my router, it tries to connect but can't get a DHCP address. I cannot ping the router in that state, of course. I have two other 10.04 laptops (with built-in wireless) and they connect just fine, as does a Windows Vista laptop. I also tried the pci=noapi item in /boot/grub/menu.lst, but that failed to show any results either. The card lights up like it should, and acts just like it did with 8.04 on the lights, but it doesn't connect. I end up seeing the "Enter your WEP password" dialog again and again unless I hit Cancel.
View 1 Replies
View Related
Feb 16, 2011
I just rebooted my netbook after updates this last week and notices the wireless is broken now. The updates updated my kernel and wl modules. I'm using a broadcom 43224 driver.If i reboot to the older kernel the wireless works.
View 5 Replies
View Related
Mar 6, 2010
After some serious trouble with Plasma, I decided to re-install 9.10. When booting up, I noticed that the wireless indicator light stayed on orange which usually means that the driver is not loaded.
I have a Broadcom 4312 in a HP Pavilion dv6. I checked the repository but no driver shows up. I seem to remember that it used to be there. Or am I mistaken and do I need to install the vendor driver from the Broadcom site?
I've added the output of lspci and dmesg | gre b43
HTML Code:
HTML Code:
View 3 Replies
View Related
Oct 23, 2009
I got a new laptop and installed Fedora 11, but I can't get the wireless working. I run lspci, it shows "Broadcom Corporation BCM4312 802.11b/g (rev 01)", so I believe the wireless card is there.I went over the thread URL... which explains in detail how to get BCM4312 working. I installed the b43 driver and the reboot. However, when I left click the NetworkManager, the only thing pops up is "Wired Network", "system eth0" and "VPN configurations". Nothing about "wireless" in there. Does this mean that the wireless driver is not installed at all? And the Network Configuration only has eth0 device.
I then tried to install broadcom-wl, but it complains there is conflict between b43 and broadcom-wl.I also tried to install the driver from autoten, it fails also.
View 10 Replies
View Related
Feb 2, 2010
My wireless was working perfectly until I accidentally let the battery run flat with the machine prevented from hibernating. Upon recovery, there was no wireless available. Checking the Hardware Drivers, I can see the Broadcomm driver as "Activated but not currently in use". Following the copious advice elsewhere I have disabled the driver, rebooted the machine, enabled it again - many times. Still the same message. What is stopping me from activating it? Bit of a noob so.
View 1 Replies
View Related
Jun 1, 2010
I've been stalking the forums for the past few days trying various fixes to no avail. I'm sorry for more clutter of this issue.
Here's what I have:
emachines e725 laptop, dual core T4400 Pentium, 64bit, running Windows 7 and just installed Ubuntu 10.04.
My ethernet port works for cat internet but wireless does not. My wireless appears but when I open browser no connection.
Here is my ifconfig:
View 9 Replies
View Related
Jan 2, 2011
I have a DEll Mini 9 - it has worked fine even though it has a limited memory. But Husband only uses to have a surf. It now wont connect to net. The Broadcom4312 Wireless Card is not working on Obunto. It has a Dell 802.11b/g Wireless LAN Mini card installed and Obunto Edition Version 8.04 Have phoned Dell and after several calls on Hold for over 15 mins each time and getting nowhere fast i am coming to you guys/girls. I am not a very good comp person, but i do get by and i am trying, so be gentle with me. in simplistic terms.
View 2 Replies
View Related
Feb 2, 2010
My wireless was working perfectly until I accidentally let the battery run flat with the machine prevented from hibernating. Upon recovery, there was no wireless available. Checking the Hardware Drivers, I can see the Broadcomm driver as "Activated but not currently in use". Following the copious advice elsewhere I have disabled the driver, rebooted the machine, enabled it again - many times. Still the same message. What is stopping me from activating it? Bit of a noob so........
View 2 Replies
View Related
Feb 22, 2011
About two days ago was when I was last able to connect wirelessly. I cannot recall a change I made to the system that would have caused this problem. Items to consider:
1. Under Network Manager, I am unable to click "Wireless Networks"
2. I ran the following code under in the terminal (sudo apt-get update; sudo apt-get install hwinfo grep; sudo lshw -C network; rfkill list; sudo iwlist scanning; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo lshw -short; uname -a; dmesg | egrep 'acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|ound|p54|prism|rtl|rt2|rt3|rt6|rt7|usb|witch|wl'; iwconfig; cat /etc/modprobe.d/* | egrep 'acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl'; sudo hwinfo --netcard ; cat /var/lib/NetworkManager/NetworkManager.state; sudo lsmod) and proceeded to run enter BIOS where I enabled the Network Driver.
3. I am still unable to get the "Wireless Networks" to even be selectable under the Network Manager
4. When I return to BIOS, the computer shuts down immediately.
5. The start-up menu won't allow me access.
6. I have an HP G60-445DX notebook and an MCP77 Ethernet..
[Code]....
View 2 Replies
View Related
Nov 3, 2010
I have a compaq c784tu and it was shitty with xp. Vista is quite crap, so i turned over to ubuntu 10.4. The configuration of the laptop is: 1.73 GHz Intel Pentium Dual Core Processor T2370 with 1-MB L2 Cache, 533 MHz FSB featuring Intel Mobile 945GML Express Chipset Motherboard, 2-GB PC2-5300 DDR2 667 MHz SDRAM (Maximum 4-GB in 2 slots), a 160-GB SATA 5400 rpm Hard Disk Drive and 8x Super Multi Double Layer (8.5 GB) Slot-in DVD Writer.Everything worked like a charm and I was able to connect to the internet through a public wifi network. However, I came home this week to my mothers house, where they have a dsl-router to connect to the internet whih uses bridge mode pppoe. I tried to connect to the internet through it, and it initially couldnt. However, I got around that by doing a clean install of ubuntu. I was able to then connect to the internet using "sudo pppoeconf" and "sudo pon dsl-provider"One night the network manager app on the top left disappeared and would not come on. I figured I had fried my wifi adapter, however, lspci -v confirmed its presence.Further, "system>admn>system testing" detected the adapter aswell. I tried the iwconfig command in the terminal the result was:
lo no wireless extensions
eth0 no wireless extensions
wlan0 IEEE 802.11bg ESSIDff/any
[code].....
View 9 Replies
View Related
Apr 8, 2010
I installed 9.04 clean yesterday to try and once again move from Windows to Linux and I thought I would give it a real try this time to learn the new OS. Well, right off the bat my wireless connection does not work. By default my WPA/WPK security was set on my router. My wireless adapter does connect to the router but there is no internet access. If I remove the WPA/WPK security and leave it open I can connect and I do have internet access but as soon as I re-enable WPA/WPK security I lose internet access. I even tried WEP security and same result. What the heck is going on with this? I am not going to leave my router unsecured but that seems to be the only way this works. I also upgraded this morning to 9.10 and same problem so this is not limited to 9.04.
View 4 Replies
View Related
Jun 23, 2010
When I first had partitioned, and formatted appropriately, I installed the newest version of Ubuntu available (Time of posting 10.4), on the partition made with bootcamp, rebooted into Linux with rEFIt Now once I booted into 10.4 I got to the desktop, it started asking me about restricted hardware drivers, so I went into System > Administration > Hardware Drivers, It then searched for the drivers, it found the STA driver, and the B43 driver, I am unable to allow both. So I went on to try ndiswrapper, I downloaded it off another pc, compiled and installed on the iMac. then I got the driver off the Leopard install disk, put that on my flash drive, extracted the files from the installer, put that on the flash drive, then I went back over to the machine in question, copied the file to the desktop, I used the cd command to navigate to the folder, then ran ndiswrapper -i bmcwl6.inf, I made sure that the inf and sys files were in there, so I didn't know what was going on exactly.
So then I went into the software sources, and enabled the cd as a software source, then went into Synaptic, and installed the drivers, it said the install was successful, however when I go back to enable it, will still refuse to activate, I have looked all around for solutions, I have even checked out other threads on this matter. The funny thing seems to be, is that everyone, or almost everyone who has this card on their computer, are upgrading to 10.04, when it worked on a previous version.
View 4 Replies
View Related
Aug 23, 2010
I just want to enable my wireless network card... how do I do that? It worked perfectly in Jaunty and it also worked when Jaunty was upgraded to Karmic, but in a fresh install of Karmic it is displayed as DISABLED:
sudo lshw | grep network:
*-network:0 DISABLED
I know this is not a bug in any kernel or anything. I now have Karmic on two identical laptops (Fujitsu Siemens AMILO, rt2500pci chipset) with the same kernel (2.6.31-22-generic). Wireless is enabled on one, disabled on the other. This is wearing me out... I am on the verge of buying Windows 7...
View 9 Replies
View Related
Oct 2, 2010
a Toshiba L650 laptop, and installed F13 x86-64 on a disk partition using install DVD. The wired ethernet on this is Atheros AR8152, and the Wireless is Broadcomm 4313. Both these devices are not supported by default. So, as per instructions on the Linux Wireless site, and some guidance on this forum, have downloaded the Broadcomm driver tar on another machine, copied it onto the Toshiba laptop using a USB device, and then extracted, and ran the b43-fwcutter. The subdirectory /lib/firmware/b43 is created and has approx 3 dozen files. However, the Broadcomm driver is not showing up as an option in the Network Manager (system-config-network) or in the lsmod command output. I tried to manually add it by doing modprobe b43 command - it then begins to appear in the lsmod, but the option to add the Broadcomm wireless driver during a "New wireless Hardware" is not appearing still. I think, at an abstract level, I need to somehow "tell" the system to add the Broadcomm driver - am just not sure how to do so. On the other hand, the Atheros AR8152 has no driver as of now, so the wired Ethernet is also not connecting. how I can download all the required files on a different machine, and then install it on the Toshiba laptop?
View 7 Replies
View Related
Aug 23, 2010
Well I see there is a lot of people which have problems with BCM4312 I read that topics but my problem kind of different..I installed 11.3 few day ago at my job. Everything was just fine...First of all I'm installed firmware
Code:
install_bcm43xx_firmware
Wireless worked fine...
[code]...
View 9 Replies
View Related
Jun 8, 2010
I'm running a Source Dedicated Server on my Ubuntu laptop, and to connect to it via external IP from other computers in the network I need to enable loopback in my router.This was working fine, but then I disconnected my laptop for a few days, and when I came back the wireless stopped working on my Xbox. I reset the router to factory defaults, and then setup everything again. It was all working fine until I enabled loopback again and power cycled my router. Now every time I do that, the internet on Ubuntu stops working and the wireless on the Xbox stops working.
Edit: You can ignore this I guess. It seems I was actually DISABLING loopback by enabling that router option, which I guess caused this. Strange, because the first time enabling this option was the only way to get my external ip to work. Oh well, everything is fine now.
View 1 Replies
View Related
Feb 21, 2011
I am attempting to iron out a detail that has been bugging me a long time.Does the procedure of providing the firmware during install actually work? Note: I am NOT asking how to install the firmware POST install. What I have done to attempt to resolve:
1. Searched forums with no luck on this specific question.
2. Google was likewise uninformative.
Steps performed:During the wheezy install, from cd (cd1 testing amd64, appx 680MB), it prompts for firmware, which it identifies as ucode15.fw. (This is only part of the file name, as I did not write the entire bit down during the install.)
View 13 Replies
View Related
Mar 13, 2010
I'm finding a hard time getting my wireless card to work, my laptop is a Dell Inspiron 1525 and this is all the info:
0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
0b:00.0 0280: 14e4:4315 (rev 01)
[ 8.375610] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
[ 8.390374] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 6, Type 5, Revision 1)
[ 8.390436] b43: probe of ssb0:0 failed with error -95
View 9 Replies
View Related
Oct 31, 2010
I'm reinstalling opensuse 11.3 with KDE. In previous setup I got it working. It is a fresh x64 install. Update all is done. Pacman repo added. code...
View 4 Replies
View Related
Mar 10, 2011
Wifi works on 11.3 with installed the broadcom-wi & broadcom-wl-kmp-desktop,but this trick doesn't work on this new 11.4.
View 9 Replies
View Related
Dec 26, 2010
currently running karmic on an old gateway laptop with kernel 2.6.31-22-generic and, as is par for how I handle challenges, I've jumped in with both feet - which is to say this is not a dual-boot situation. I've spent some time reading the forums (and other sources of information) and am grateful for all the knowledgeable people who are willing to share what they know.
My operating system seems to be functioning properly.I can get online via ethernet, but not via wireless. I have a lucent orinoco gold PC24E-H-FC (PCMCIA) card, which the computer isn't seeing. I am trying to follow the instructions here: [URL] to install the driver. Everything is going well until I get to the sudo make line. At that point I get the following display:
make -C /usr/src/linux-headers-2.6.31-22-generic M=/usr/src/orinoco-0.15rc4 KERNELRELEASE= modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.31-22-generic'
/usr/src/orinoco-0.15rc4/Kbuild:8: *** Wireless extensions are not enabled. Stop.
[code]....
how I can fix it so I can continue on with the instructions. (For the record - if I just continue on, I can change directory in the next line, but I cannot remove either hermes or orinoco as "no such file or directory" seems to exist.)
View 3 Replies
View Related
Jul 17, 2010
after finally installing 11.3, I found that my wireless NIC had stopped working. I've spent about 4 hours trying various online tutorials to get the card working, but I'm still right where I was when I began. The card as reported by lspci:
[Code]....
View 9 Replies
View Related
Jun 11, 2010
I have an HP 2133 Mini-Note [KX869AT] with a Broadcom 4312 wireless card. I've had Ubuntu 10.04 on my machine for a few weeks now and everything was great until my wireless card abruptly stopped working. It doesn't detect any wireless networks,uch less connect to them. I tried reinstalling the proprietary driver, but that hasn't worked.
View 1 Replies
View Related
May 9, 2010
I've already got the b43-fwcutter package and a driver called 'b43' appears in System > Administration > Hardware Drivers but it does not seem to enable. Another, Broadcom STA wireless driver, does enable, but I'm not picking up the wireless signal.
Code:
$lspci 05:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 01)
08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Code:
$ sudo lshw -C network
SCSI
[Code]...
View 5 Replies
View Related
Oct 25, 2010
i just got ubuntu yesterday and had to play around with some settings and the fw-cutter tool to get my wireless working and it was...although i upgraded the kernel to 2.6.32-25-eneric...and it stopped working. the simple solution is to use the previous kernelersion...the wireless works there, but thats just not good enough for me ... it recognizes my card is there it just wont connect. originally i was using b43 driver and now it does not show in the system>hardware drivers list only the sta driver does, although when i try to install and activate it i get the error message "sorry, installation of this driver failed.please have a look at the log file for details: /var/log/jockey.log"
View 5 Replies
View Related
Jan 8, 2011
I just put 10.10 on my D830 and I love it except for a delay when I'm using the internet. When I click on a link while surfing the web it takes about 13 seconds before it responds. After that it works just fine.
My Windows 7 PC and my Macbook Pro don't do that so I'm guessing it has something to do with Ubuntu.
View 5 Replies
View Related
Jan 6, 2011
After a fresh install of 10.10 on a Dell XPS 1330 I cannot get any audio when connecting to an LCD TV via HDMI. I get video no problem but sound only from internal speakers.
Under System/Preferences/Sound on the Hardware tab there is an profile entry for 'Digital Stereo (HDMI) Output' but if I select this all goes silent.
I checked alsamixer and nothing is muted. The aplay -l output is below.
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: STAC92xx Analog [STAC92xx Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
[Code]....
View 9 Replies
View Related
Jan 20, 2011
I have installed CentOS 5 just downloaded yesterday on a Dell D620. Everything but the wireless card works. So I found this article:
http://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom
and followed it step by step and was able to complete all of the tasks. The problem is that obviously it still won't start. It is not even recognized as an adapter but when I run lspci -v it is there sure enough. When I look under the networking GUI it is listed there but it has no MAC assigned to it. Please let me know what command output you need to see and I'll get here asap. I have searched this forum and other sites and nothing so far has worked.
View 1 Replies
View Related
May 16, 2011
just installed ubuntu 11.04 on my old laptop (Dell latitude XT), to experience this OS. But for some reason I cannot get online, both wired and wireless network are 'grey', and i cannot enable them. Even when I try to go online with a USB wifi dongle,I also cannot enable wireless. Enabling Networking is selected.
I include the information I collect and hope this will allow you to give me a diagnose on how to make my wireless work.
lspci, for the build-in card
Code:
View 1 Replies
View Related
