I have an HP 2133 Mini-Note [KX869AT] with a Broadcom 4312 wireless card. I've had Ubuntu 10.04 on my machine for a few weeks now and everything was great until my wireless card abruptly stopped working. It doesn't detect any wireless networks,uch less connect to them. I tried reinstalling the proprietary driver, but that hasn't worked.
View 1 RepliesI have a DEll Mini 9 - it has worked fine even though it has a limited memory. But Husband only uses to have a surf. It now wont connect to net. The Broadcom4312 Wireless Card is not working on Obunto. It has a Dell 802.11b/g Wireless LAN Mini card installed and Obunto Edition Version 8.04 Have phoned Dell and after several calls on Hold for over 15 mins each time and getting nowhere fast i am coming to you guys/girls. I am not a very good comp person, but i do get by and i am trying, so be gentle with me. in simplistic terms.
View 2 Replies View Relatedafter finally installing 11.3, I found that my wireless NIC had stopped working. I've spent about 4 hours trying various online tutorials to get the card working, but I'm still right where I was when I began. The card as reported by lspci:
[Code]....
How do you enable repos? Namely RPMFusion set? I have 2 repo's that are currently in stalled:
[root@dv5-1235 Joe]# yum repolist
Loaded plugins: presto, refresh-packagekit
repo id repo name status
fedora Fedora 12 - x86_64 enabled: 19,122
updates Fedora 12 - x86_64 - Updates enabled: 755
repolist: 19,877
I'm trying to get my Broadcom 4312 working again since FC10. I noticed that RPMFusion isn't listed. This would answer why I can not install Broadcom -wl.
When I first had partitioned, and formatted appropriately, I installed the newest version of Ubuntu available (Time of posting 10.4), on the partition made with bootcamp, rebooted into Linux with rEFIt Now once I booted into 10.4 I got to the desktop, it started asking me about restricted hardware drivers, so I went into System > Administration > Hardware Drivers, It then searched for the drivers, it found the STA driver, and the B43 driver, I am unable to allow both. So I went on to try ndiswrapper, I downloaded it off another pc, compiled and installed on the iMac. then I got the driver off the Leopard install disk, put that on my flash drive, extracted the files from the installer, put that on the flash drive, then I went back over to the machine in question, copied the file to the desktop, I used the cd command to navigate to the folder, then ran ndiswrapper -i bmcwl6.inf, I made sure that the inf and sys files were in there, so I didn't know what was going on exactly.
So then I went into the software sources, and enabled the cd as a software source, then went into Synaptic, and installed the drivers, it said the install was successful, however when I go back to enable it, will still refuse to activate, I have looked all around for solutions, I have even checked out other threads on this matter. The funny thing seems to be, is that everyone, or almost everyone who has this card on their computer, are upgrading to 10.04, when it worked on a previous version.
After some serious trouble with Plasma, I decided to re-install 9.10. When booting up, I noticed that the wireless indicator light stayed on orange which usually means that the driver is not loaded.
I have a Broadcom 4312 in a HP Pavilion dv6. I checked the repository but no driver shows up. I seem to remember that it used to be there. Or am I mistaken and do I need to install the vendor driver from the Broadcom site?
I've added the output of lspci and dmesg | gre b43
HTML Code:
HTML Code:
I have a HP Mini 5105 SSD netbook, runing Ubuntu 10.10 with 2Gb RAM. My wireless card is a Broadcom BCM43224 802.11a/b/g/n. Its driver is enabled and running. The wired network connection runs fine too. The problem: Wireless stopped working. When I right click on the network icon, the enable network option is clicked, but the "enable wireless" option is listed in dark grey and cannot be clicked on. I have recently updated my kernel version to 2.6.35-24-generic. What I have already tried: this one too I got to know there seems to be a problem with the 2.6.35-24-generic kernel. I have gone into the GRUB menu (it took some time to find out that you have to keep the Shift key pressed during startup for the GRUB menu to show), chosen the older kernel version (2.6.35-23-generic) and then removed the faulty one. Nevertheless, nothing has changed. I still cannot enable the wireless. The outcome to lshw -C network is:
[code]...
Im having problems making my wireless card "Broadcom 4312" work on centos 5.4 X64 , i have installed and built the driver from their official site and inserted its module successfully, but whenever i try to avtivate the interface "called eth1" i get the following
Error for wireless request "Set Encode" (8B2A) :
SET failed on device eth1 ; Invalid argument.
Error for wireless request "Set Encode" (8B2A) :
SET failed on device eth1 ; Invalid argument.
after having tried out almost all suggestions found here and elsewhere on the internet, i'm somewhat at my wits end The situation: I'm running Kubuntu 32Bit Version (at the mom 10.4) on a HP-Compaq 6735s (AMD Processor, Vanilla 32Bit Install). My first Install was last year with 9.4 and the Broadcom 4322 wireless worked like a charm after installing the proprietary STA-driver under System -> Hardware Drivers. As the update didn't work out really without glitches, i did a fresh install and lost my wireless. I tried various combinations and tutorials but to no avail. My card is found, the driver installed, but i cannot access my access-point. I can SEE the access point (and all my neighbors'), but knetworkmanager does not seem to do anything. To be sure, I installed wicd (nice tool by the way). Trying a connect here told my my credentials were bad (incorrect passphrase for my WPA2 Personal auth), which is not true. I tried connecting without security, didn't get an IP. So it seems somehow the card is working, but all functions needed for passing information to the access-point are unavailable.
This is what I tried:
both broadcom-drivers
fw-cutter
installing the driver by hand
Installing the driver via Hardware Drivers produced the same results as any other, viz the card is working, but not connecting. Unfortunately knetworkmanagers error messages are a bit sparse, or rather non existant. My guess is that somehow the firmware is not properly loaded (or the wrong type??).
I have an HP Pavilion notebook with a Broadcom WLANcard that had been working very nicely in Fedora Core 10 until this evening, when I took my notebook to a conference room where there was no internet access. (I tried to connect to wireless networks, but there were none in the area, as I discovered.) am now unable to connect to my local (home) wireless network as the device is now non-existent . Can someone please walk me through the steps to fix this or re-install it (I have tried reinstalling broadcom-wl, but that didn't help). My lspci listing is reproduced below:
Code:
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
[code]...
I've already got the b43-fwcutter package and a driver called 'b43' appears in System > Administration > Hardware Drivers but it does not seem to enable. Another, Broadcom STA wireless driver, does enable, but I'm not picking up the wireless signal.
Code:
$lspci 05:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 01)
08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Code:
$ sudo lshw -C network
SCSI
[Code]...
I've been stalking the forums for the past few days trying various fixes to no avail. I'm sorry for more clutter of this issue.
Here's what I have:
emachines e725 laptop, dual core T4400 Pentium, 64bit, running Windows 7 and just installed Ubuntu 10.04.
My ethernet port works for cat internet but wireless does not. My wireless appears but when I open browser no connection.
Here is my ifconfig:
i just got ubuntu yesterday and had to play around with some settings and the fw-cutter tool to get my wireless working and it was...although i upgraded the kernel to 2.6.32-25-eneric...and it stopped working. the simple solution is to use the previous kernelersion...the wireless works there, but thats just not good enough for me ... it recognizes my card is there it just wont connect. originally i was using b43 driver and now it does not show in the system>hardware drivers list only the sta driver does, although when i try to install and activate it i get the error message "sorry, installation of this driver failed.please have a look at the log file for details: /var/log/jockey.log"
View 5 Replies View RelatedI just put 10.10 on my D830 and I love it except for a delay when I'm using the internet. When I click on a link while surfing the web it takes about 13 seconds before it responds. After that it works just fine.
My Windows 7 PC and my Macbook Pro don't do that so I'm guessing it has something to do with Ubuntu.
I have installed CentOS 5 just downloaded yesterday on a Dell D620. Everything but the wireless card works. So I found this article:
http://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom
and followed it step by step and was able to complete all of the tasks. The problem is that obviously it still won't start. It is not even recognized as an adapter but when I run lspci -v it is there sure enough. When I look under the networking GUI it is listed there but it has no MAC assigned to it. Please let me know what command output you need to see and I'll get here asap. I have searched this forum and other sites and nothing so far has worked.
I have a Broadcom BCM4311 wireless card on my Dell D620 laptop.
Code:
09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755M Gigabit Ethernet PCI Express (rev 02)
0c:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)
My wireless works perfectly with my university networks. But I have problem connecting to my house router. The first time I installed Ubuntu 10.10, it connected to internet and worked well. After a restart needed by nVidia driver, my house wireless stopped working while my university wireless still works. I have tried reinstalling the driver using System/Administration/Additional Drivers and manually
Code:
sudo apt-get update
sudo apt-get --reinstall install bcmwl-kernel-source
Ever since I upgraded to the new Ubuntu, I have been having problem with wireless. In the "Hardware Drivers" I come up with 2 drivers:
1) Boadcom B43 wireless driver
2) Broadcon STA wireless driver
I activated the first one, but latter noticed that the wireless was not working, so I tried installing the second and it returned this message:
Quote:
So I unactivated the first and then it disappeared leaving me with the second, and its error message.
Quote:
What should I do now?
The output for "lshw -C network":
Code:
The last few pages of /var/log/jockey.log.
Code:
After upgrading to the latest Ubuntu, my wireless card stopped working. I keep on pressing the button but the little orange light wont come on...I have an aspire 5517 with "Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)" I have tried drpjkurian's tutorial for madwifi with no success . (http://ubuntuforums.org/showthread.php?t=1309072
View 2 Replies View Relatedthe distro is slackware64-13.37 I did install the firmware it was working I have no Idea why it quit wicd sometimes looks like it's connected only to have mozila not find a network connection most of the time wicd times out when obtaining ip address the router is working just fine and was reset to out of the box factory defaults and is working with windoze vi-stool from dmesg I get
[code]....
Well, I have an issue with my wireless card in Ubuntu 10.04, my wireless card model is:
the D-Link WIRELESS N 150 DESKTOP ADAPTER DWA-525. I was already successful getting it to work by using the RaLink driver suggested here and following the instructions in their readme.But after a system update I performed through Update Manager (in which I guess the kernel was updated), the device stopped working completely. The wireless icon remains(in the top panel), but it displays a red exclamation mark next to it
I have a relatively new F12 install (one week old) on which I got my wireless Broadcom card working using kmod-wl-PAE. It was a very easy process - not really a process just yum install kmod-wl-PAE.
After a few updates, I notice that the wireless card stopped working. I assumed maybe there was an update that conflicted, so I did a reinstall of kmod-wl-PAE and it worked again immediately.
Then I started installing compiz-fusion. Immediately after, wireless is broken again. So I yum erase kmod-wl-PAE and then yum install kmod-wl-PAE and it works again.
Now, only slightly later that same day, wireless stops working more or less randomly and I cannot get the reinstall of kmod-wl-PAE to fix it. So I uninstall, disable compiz-fusion, shut down, and restart the computer to try again. My thought is that maybe along the way my autostart compiz or something about compiz is causing the wireless not to configure properly. When I restart, wireless is working. Without kmod-wl-PAE installed:
yum info kmod-wl-PaE
Loaded plugins: presto, refresh-packagekit
Available Packages
Name : kmod-wl-PAE
Arch : i686
[Code].....
One, how is this even possible, and two, what is going on with the wireless working, not working, working, not working?
I'm using Ubuntu 9.10 on a Lenovo ThinkPad T61 using an Intel PRO/Wireless 3945ABG. My laptop's ability to connect to a wireless network stopped last night, and I'm not sure why. It's definitely something on my end, as my roommate can connect to the internet on a Windows box. I can wire in without a problem, but that's a pain and my Ethernet cable got lost in the shuffle when I moved back to school. I've been able to get into this network before and nothing about it has changed. I've been able to hibernate and restart and such and nothing has ever needed to be reset.
The router's a D-Link WBR-2310. Wicd and Network Manager see the network (I'm back to using wicd) , but wicd appears to get stuck at "Obtaining IP address..." and says "Unable to connect: Cannot obtain IP address". I know my password is correct (I set up the router and I'm the CS undergrad in the apartment so I manage it), lspci sees the wireless card, ifconfig and iwconfig return information about the interface, dmesg|grep wlan0 doesn't seem to have anything terribly out of the ordinary, but here's that output:
Code:
allyanncah@taliesin:~% dmesg | grep wlan0
[ 23.514202] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 36.609016] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 38.756143] wlan0: direct probe to AP 00:24:01:cb:4e:7e (try 1)
[ 38.758791] wlan0: direct probe responded
[ 38.758796] wlan0: authenticate with AP 00:24:01:cb:4e:7e (try 1)
[ 38.760587] wlan0: authenticated
[ 38.760609] wlan0: associate with AP 00:24:01:cb:4e:7e (try 1)
[ 38.763318] wlan0: RX AssocResp from 00:24:01:cb:4e:7e (capab=0x431 status=0 aid=1)
[ 38.763322] wlan0: associated
[ 38.765502] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready .....
I've tried:
- reinstalling wicd
- uninstalling wicd and installing network-manager
- restarting
- shutting down and booting back up
- restarting the router
- sudo /etc/init.d/networking restart
- taking the interface down and back up with ifconfig
I haven't changed anything recently in regards to my wireless card, and all the fixes I've tried are things I've done before without an issue. The only thing I'm wondering about is if doing a hard reset might have broken something (I know this is a cardinal sin, but there's a whole 'nother problem I haven't been able to fix with the OS hanging every once in a while over a VPN daemon when it tries to shut down or restart -- I've left it for hours to see if it actually gets anywhere and no luck, won't do a soft reset). I'm nervous about reinstalling the driver just because I've never had to do it and drivers are a finicky business. I imagine there's a config error somewhere?
I have a new Thinkpad t510 laptop with an intel centrino wireless N card (no bluetooth). I installed ubuntu a couple weeks ago after I got another hard drive in the expansion bay. I have the drive partitioned into two sections, 250gb for file storage, and 250gb for the linux OS. Currently no other OS is installed on the other harddrive.
I have had everything perfect for the past couple weeks, but once i installed some updates today, my wireless fails to work now. Just some general info that you might ask me, lspci | grep Network, returns
00:19.0 Ethernet controller: Intel Corporation 82577LM Gigabit Network Connection (rev 06) 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 Furthermore, on the top right of my screen, my wireless is grey'd out and says no network devices available on hover.
[Code]...
Im trying to connect to my college wireless network. I have looked a thinkwiki and no one has posted any bugs. Any ideas on getting it working again?
The card uses a momentary switch to turn on at and off and it doesn't work. I read that there is a way to have the card turn on by default on boot but I can't figure out how to do it.
View 1 Replies View RelatedI've been having some trouble with my recently bought laptop.
Type: Dell Vostro 1015.
You can see the full specification by following the link in my signature.
What's important is this code..
The system freezes randomly and all I can do is to push the power button and force-turn it off.
I'm not sure, but I think it's the wireless. It's my second Fedora install on this machine, and the second was all right until I set the wireless drivers (or I had luck to have no stops).
Well I see there is a lot of people which have problems with BCM4312 I read that topics but my problem kind of different..I installed 11.3 few day ago at my job. Everything was just fine...First of all I'm installed firmware
Code:
install_bcm43xx_firmware
Wireless worked fine...
[code]...
I'm finding a hard time getting my wireless card to work, my laptop is a Dell Inspiron 1525 and this is all the info:
0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
0b:00.0 0280: 14e4:4315 (rev 01)
[ 8.375610] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
[ 8.390374] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 6, Type 5, Revision 1)
[ 8.390436] b43: probe of ssb0:0 failed with error -95
I'm reinstalling opensuse 11.3 with KDE. In previous setup I got it working. It is a fresh x64 install. Update all is done. Pacman repo added. code...
View 4 Replies View RelatedWifi works on 11.3 with installed the broadcom-wi & broadcom-wl-kmp-desktop,but this trick doesn't work on this new 11.4.
View 9 Replies View RelatedI have a Broadcom Corporation NetXtreme BCM5721 network card on my server at work.Everything works fine for a few weeks, then randomly the network connection on the server will stop working. After it stops working, I will try to reconnect with the network manager, it shows a wired connection available, it shows the "connection in progress"animation, then the "connection disabled" icon.
I uninstalled the network manager and used manual configuration, but do you think the network manager was the issue? I can't have the server disconnecting randomly every few weeks with no way to know what the real problem is. Was there an issue with the network manager with 10.04?