I want to install printer HP Deskjet k209 in Debian Lenny but i am unable to install because printer driver is not available in this distribution..
View 2 Replies
I installed the Printer, but Xsane does not recognize the scanner, how can i acivate the scanner. my system is Debian Lenny 507 Kde i386. I have looked through the posts in the forum, but found nothing that can help me. can somebody point me in the right
View 14 Replies View RelatedI have Ubuntu version 10.10 and I'm trying to install the HP DeskJet 1000 J110a printer. I have HPLIP version 3.11 (the latest version I believe). The printer shows up but when I try to print the error message reads: Printer requires the 'foomatic-rip-hplip' program but is not currently installed.
View 2 Replies View RelatedI just upgraded to lenny (stable) from a working etch system. It went pretty nicely but I'm having a problem with the print system.
Ok, I have an HP Laserjet 4M+ connected to my system by USB. (I have another color printer too and a scanner but I don't use them often).
I use CUPS. I never bothered with the HPLIP packages because straight cups has always worked well.
What happens now is that I'll send a job to the printer and nothing will happen. The printer won't get it. Looking at CUPS on the localhost:631 page I can see that the printer is on, connected, ready; the job is there too but just stuck on "processing".
Now here's the thing. If I manually load the ehci_hcd module with "modprobe ehci_hcd" then the job will make it to the printer and it will print.
I can't just make that module load at boot time because if I do and the printer is off, it doesn't work. (I have to unload it and reload it). For whatever reason, I have to make sure that module gets loaded AFTER the printer is turned on, or nothing gets sent to the printer!
I just installed HPLIP using Synaptic package manager. One of the configure parameters (shown by 'hp-check -r') is
Code:
Am I correct in assuming that this means that a network printer will not work? Is there a way to override this while still using synaptic package manager? Would I then be able to use a network printer?
I have my eye on the HP photosmart plus B209A - and it looks like HPLIP supports it (there is a ppd file for it).
I just upgraded from Debian Etch to Debian Lenny (stable) and now I am having a tough time getting my printer to work. I have a LaserJet connected to the system with a parallel to USB cable.What happens is that when I go to print, nothing happens, CUPS says the printer is processing, and the job just sits there. If I load the ehci_hcd module, then the printer is fine.But it's not as easy as setting it up so that ehci_hcd is autoloaded at boot, because if that happens then when I turn on the printer I have the same problem. I have to actually unload ehci_hcd and then reload it!
View 12 Replies View RelatedWhen I go to System->Administration->Printing no window pops up. Down on the bottom panel it says "Starting Printing" and then goes away. I'm trying to install my HP Deskjet printer,
View 3 Replies View RelatedAfter clicking on the print option on ms -word, printer does not respond! In the print dialogue box it shows that ink cartridge empty, but even after refilling it, it shows the same status!
View 1 Replies View RelatedUbuntu 1010 64bit
HP Deskjet 5740 USB interface
The printing has been running without problem ever since the installation of this box at least >1 year. Today I found it stop working with following warning:
Code:
Filter /usr/lib/cups/filter/hpcups for printer Deskjet-5700 not available
I'm running a standard 13.1 32 bit install with an HP deskjet 990C, run off of USB. Until today everything has printed properly. Now nothing prints. Nothing has been installed unless it came through slackpkg, and yes it is still on the correct setting for arch and revision. CUPS shows printer as installed, accepting jobs an idle. No error messages are appearing but nothing is reaching the printer. The info I can glean is from the error logs in CUPS:
[Code]....
I have recently acquired me a HP all-in-one printer model HP Deskjet F2483. The printer works fine but am having issues getting the scanner to work. Following instructions I found to Google, this is what my shell looks like:
Code:
sh-4.0$ sane-find-scanner
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
[Code]...
My HP Deskjet D-2660 will not print. I can print to file but not the printer. I am running Ubuntu 10.04 and have no other problems. I have installed hpip and hpijs form HP and cups was made available via and upgrade. I have a lot of data from var/log/cups/error_log but don't know what it is supposed to say.
I can print to file and everything else I check seems to say that all is right. Is there any glaring faults that I should look for?? As I stated on the other post I get a message that the print job has been sent to the printer and then another message stating that the print job has completed. In system/administration/printing, the printer shows up properly and has a green check mark on it. Connected to localhost shows at the bottom of the little window. Under /printer it shows shared and enabled Then under printer/properties, it shows as the HP Deskjet D2600 series the location is given as john-desktop It defines the Device URI: hp:/usb/Deskjet_D2600_series?serial=CN9ANDF0ZT05C9 shows the Make and Model HP Deskjet d2600 Series hpijs,.. printer state: idle
Across the bottom it theoretically allows you to print a test page or clean the print heads. (won't print) On the printing-local host small page that opens under system/administration/printing there is no group under that heading only new group or new group from selection. I never named a group since I am the only user.
I have shut the printer down and disconnected the USB and rebooted. Then connect the power and plug in the USB cable I get all the same answers nothing appears to change. Here is some of the var/log/cups/error_log file. It does this over and over every minute same thing. The print que is empty from both administration and applications.
[Code]....
I'm trying to install hp DeskJet 6500 printer on a network.
My Centos version is
Linux xxxxx 2.6.18-194.26.1.el5xen #1 SMP Tue Nov 9 13:35:30 EST 2010 x86_64 x86_64 x86_64 GNU/Linux
Ofcourse My printer model is not showing up on the list of printer list when using ipp based configuration.
so while searching around, I came across article to install hplip at
[URL]
and I tried to install the following hplip version with centos.
[URL]
Running the configure with following arguments
./configure --with-hpppddir=/usr/share/ppd/HP --libdir=/usr/lib64 --prefix=/usr --enable-qt4 --enable-doc-build --enable-cups-ppd-install --disable-foomatic-drv-install --disable-foomatic-ppd-install --disable-hpijs-install --disable-policykit --disable-cups-drv-install --enable-hpcups-install --enable-network-build --enable-dbus-build --enable-scan-build --enable-fax-build
I get following error
configure: error: cannot find net-snmp support (or --disable-network-build)
But net-snmp is installed on my system, so, I tried with disable-network-build and tried to get around the problem, the next error I get is
checking for usb_init in -lusb... no
configure: error: cannot find libusb support
I have an Acer Aspire 6930 laptop that I'm setting up for my wife with Debian Lenny. It has an Intel 5100 wireless card. I'd like to get a driver for the card without having to install a new kernel.
View 11 Replies View RelatedI installed the new debian_lenny_5.0.1_amd64 x64, i am having a nVidia Geforce 8500 GT 512 RAM display card. I was trying to install the driver using the synaptic package manager. I installed them, but i was not able to use the driver. I don't know where the drivers are installed and how to use it. I checked the xorg.conf , and the nVidia driver is not listed there. how to install them .
View 9 Replies View RelatedI have installed Debian Lenny and the Driver for an NvidiaCard GTX280. As this card is not supported by the debian-repositories, i have installed the driver from the nvida-Site. It works ok, but there's one thing: When i have compiz fusion activated, the caracters in the shell are sometimes hidden (pls see attachment).
View 4 Replies View RelatedI have problem with my printer HP Deskjet D1460. My printer is configured and works. When I send a file on the print, the printer clings a sheet of paper and starts to print, but a paper as was clean so clean and remains, after printing.
View 2 Replies View RelatedI have a printer connected locally to my Debian box. It runs fine via cupsd.I am also running a Windows 2003 VMware guest which I would like to use the printer (use as a local printer, not a network printer).
VMware offers a connection via USB, so it should work. The printer I have plugged locally into the Debian host is recognised by the Windows 2003 guest, but it won't print. I get an error message saying that the printer is still connected to the host OS, and that I need to remove (or presumably disable) the host driver before the guest can use the printer.
So how can I find out which printer driver/module is being used by the Debian host to connect to this printer? And what is the best way to temporarily disable it, while my VMware guest is running?
I have bought a BrotherHL-1110 laser printer. But there is no driver on my system. I have downloaded source code but don't understand how to compile it. (
It does only exist driver-packages for 32 bits: hl1110cupswrapper-3.0.1-1.i386.deb and hl1110lpr-3.0.1-1.i386.deb)
My system is:
Release 7.8 (wheezy) 64-bit
Kernel Linux 3.2.0-4-amd64
GNOME 3.4.2
AMD Athlon(tm) II X2 245 Processor × 2
The source code contain the following files:
-> pwd
/home/joe/Desktop/BrotherHL-1110/hl1110cupswrapper-GPL_src-3.0.1-1
-> ls -R
.:
brcupsconfig Copying filter PPD
[Code] ....
How do I compile and install it on my computer ? ( Or get the printer working ? )
I've bought a HP Photosmart printer, HP Photosmart wireless e-All-in-One printer - B110a and i've got a problem installing it properly. I'm using Debian 6.0 Squeeze. When i connect the printer, Debian doesn't recognize my printer as the Photosmart B109 printer for unknown reason. When i go to the site of HP and search for a driver, it directs me to this site:I've downloaded that latest hplip file as a .run file and installed it. My printer is recognized proparly, but when i try to print a colored image, it comes out black/white. Something is not crrect. Does anyone recognize this problem with this type HP printer?
View 7 Replies View Relatedi was trying to use gnome and kde but i don't like them. I tried xfce and it seem to fit my needs but.My computer is used to be powered on for a weeks. While time passes, a process xfdesktop begin to use more and more memory and to free RAM i need to log out and log in again.
I tried squeeze yesterday on my virtual machine and it has 4.6 and seem not to have that bug, RAM usage is static(yes it still works when i write this and have memory usage 34492k, which is not changing for an hours of usage already), also 4.6 is MUCH better than 4.4.
i already tried adding squeeze to "sources.list" but i can see too many dependencies which should be upgraded if i install 4.6, i'm beginning to afraid it can crash entire GUI(or entire system, i can see there is libc6 required to be updated).
This is my first attempt with Yum and Fedora for that matter. I need to load a print driver and network driver for an MX860 printer. I downloaded the drivers and they are in the download folder. When I try to install I get what is below. How do I resolve? Do I need to identify where the driver is? If so, how?
[compaq@compaq ~]$ su -c'yum install cnijfilter-mx860series-3.10-1-i386-rpm.tar.gz'
Password:
Loaded plugins: refresh-packagekit
updates/metalink | 15 kB 00:00
Setting up Install Process
No package cnijfilter-mx860series-3.10-1-i386-rpm.tar.gz available.
Nothing to do
[compaq@compaq ~]$
I'm trying to add my Samsung SCX4500W printer to my opensuse 11.2 machine running KDE.From Yast->Printer->Add printerI am able to set the printer up, however there is no driver for my specific network printer. Samsung does provide a linux driver but I have no idea what I'm doing when installing peripherals on linux basically
View 3 Replies View RelatedHow can i install it? Which version of Catalyst is better to use? I know that Catalyst 9.3 is the latest version, which has full support of ati x1250, in later drivers my video-card is "legacy". I'm searching for a long period of time and can't find the answer... may be it is impossible to install suitable Catalyst for my ati on lenny and it is better to use older Debian? And if Yes, then which one?
View 9 Replies View RelatedI have an HP Designjet z3200ps but I cannot find a linux driver for it. What should I do now ?
And I'm also wondering if the linux driver for etc device is not developed, what should the Linux gurus do ?
Does anybody know if there is a driver for the dell 946 printer?
View 1 Replies View Relatedok my printer is a "hp deskjet f4240 all in one" my OS is Ubuntu 8.04i have installed many hp drivers that say they work in ubuntu and work for that printer. but they wont work. my printer however is found. this problem only happend after i reinstalled ubuntu.
View 1 Replies View Relatedi have a dell v305 and i need the driver to use it but the disk wont install on linux how can i get the driver for my printer
View 1 Replies View RelatedI am currently using ubuntu 10.10 and trying to install the current driver for a lexmark x2600 printer. I retrieved the driver from the lexmark site, to be specific the debian version. Once I had the driver unzipped I was able to run the program to start installing it. However the problem is that it requires root privileges in order to install. So I input my admin password to allow the install. Apparently the password I use is not correct even though it is the admin/root password on my system.
View 4 Replies View RelatedI have a Samsung ML-1430 laser printer connected to my Fedora 12 box. I downloaded the appropriate Linux driver tar file from the Samsung website. After extracting the tar file into a directory called image, the following took place:
This generates a "Linux Printer Package Setup" pop-up screen.
The following error messages occur after I process the pop-up screen which specifies a default install path [/usr/local/linuxprinter] and asks me to check an "Install CUPS 1.1" box and a "Begin Install" box.
