Debian Configuration :: Doesn't Boot After Unloading Alx

Aug 16, 2015

I'm using debian 8 on a notebook and since I tried to get the wifi working (another story...) I wanted to unload and load the alx driver module. So I used rmmod alx and when I tried to reload with modprobe, it didn't find the device (not the module). So I rebooted and now the notebook won't start. There's just the emrgency mode, so I log in as root and journalctl -xb gives me some erros:

Code: Select allsystemd-modules-load.service: main process exited, code=exited, status=1/FAILURE

Failed to start Load Kernel Modules.Unit systemd-mdoules-load.service entered failed state.Then it fails to start the modules ip, ppdev, parport_pc and fuse.Next error is

Code: Select allboot-efi.mount mount process exited, code=exited, status=32

Failed to mount /boot/efi.Followed by

Code: Select allDependency failed for Local File System.
And last but not least
Code: Select allFailed at step EXEC spawning /bin/plymouth: No such file or directory.

There was also an error at the first time "Failed to load autofs4", so loaded it manually with modprobe. As this worked, I opened the /etc/modules - which was empty, don't know whethere it was also empty before or not - and wrote autofs4 in the file. autofs4 seems to load succesfully, so I tried writing also ip, ppdev, parport_pc and fuse, but I just get the error for these last four twice... But lsmod shows some loaded modules (autofs4, ext4, crc16, mbcache, also alx and say 15 more).You should also know that I use an extra boot partition and use EFI.

View 8 Replies


ADVERTISEMENT

Debian Configuration :: Apache2 Doesn't Start At Boot Time?

Dec 6, 2010

I am running Debian-Squeeze with apache2. However, apache2 doesn't start at boot time, even though there is of course the required script in init.d. I can start it later on using "/etc/init.d/apache2 start". I have checked the configuration with "apachectl configtest" - giving the answer "Syntax ok". How do I get it to start automatically at boot time?

View 1 Replies View Related

Debian Configuration :: Multipath Configuration On 5.0 64 Bit - Doesn't Create The Relative Devices

Jul 20, 2011

i have a HP MSA 2312fc SAN with 2 LUNs configured. The first LUN (LUN ID 1) is correctly connected to the system, but when i connect the second LUN (LUN ID 30), i find in the syslog this message: multipathd: 8:64: size 6835937472, expected 5267578112. Discard

Here is the multipath.conf

[Code]....

So I correctly see the two luns, but multipath doesn't create the relative devices. Under /dev/mapper I see: control mpath0 mpath0-part1 mpath0-part1 is the first lun, the one I mounted in a directory under filesystem. I can't find the device for the second lun

View 1 Replies View Related

Debian Configuration :: Boot Via PXE, "no Default Or Ui Configuration Directive?

Mar 19, 2011

A week ago I opened this thread viewtopic.php?f=17&t=61580 in "Board index ‹ Help ‹ Installation" and asked for a moderator to move this to here. Because it hasnt happened up to know, I am reopening the thread here. It would be reeeeally great if somebody could help me with my problem!

I own two computers, one netbook and one laptop. I want to boot my netbook as a diskless client via PXE.I set up a dhcp-, tftp and nfs-server on my laptop but when i boot my netbook, the follwoing messages are displayed:(to make it more clear, i uploaded the whole output and shortened the output below)

[Code]...

View 1 Replies View Related

Debian Configuration :: NIC Goes To Sleep And Doesn't Come Up Again

Aug 5, 2015

i have the following problem which i couldnt solve in the past weeks. We have two Server with an onboard "Atheros AR8161 Gigabit Ethernet (rev 10)" and a quad "Realtek RTL8111/8168B" network adapter connected via PCIe. One of the servers is running Debian Wheezy with a custom 3.2.53Kernel (compiled from linus repository) and the second one runs Debian Jessie with stock kernel. Both are running XFCE4.

Each of the computers are connected to a local network (192.168.0.1 respectively .2) and to the intranet of our institute (10.20.0.81 respectively .82). After a random time they are not accessible via the intranet (ping doesnt work, ssh gives no route to host). However, i can still ping them over the local network. Also, at the moment i try to establish a ssh connection over the local network, the computer is again acessible via the intranet.

I already tried the boot options acpi=off and pcie_aspm=off without success. Additionally we switched from the onboard Atheros NIC to the Realtek, but everything stays the same. Therefore i don't believe that it is driver related.

For me it looks like that the NIC goes to an energy saving mode which is not handled correctly by our intranet. However, how can i avoid that the NIC goes to energy saving state? Is there a way to disable the D-states?

View 3 Replies View Related

Debian Configuration :: Laptop Fan Doesn't Run?

Jul 14, 2011

I have installed Squeeze on my laptop, an Acer 5315.The fans never turn on, and the laptop eventually overheats and shuts off.This is not a hardware problem, because Lenny, on another partition, works fine.I have poked around, and discovered that the temperature sensor, as reported by "acpi -V", and in /sys/devices/virtual/thermal, does not get updated. It seems to get read at boot, but the reading never changes, no matter how hot the machine gets.

Specifically, if the machine is cool, acpi reports 40 degrees C, and goes on reporting the same number until the machine overheats and shuts down.On the other hand, if the machine is hot (because it's been running without the fan), and I reboot, then the reading at boot is usually either 75 or 85, and the fan turns on during boot, and stays on, at high speed, until the next reboot, and the reading never changes during the whole time

View 2 Replies View Related

Networking :: Multiple IPs One NIC Configuration Doesn't Load At Boot On Fedora 12?

Dec 2, 2009

I have a Fedora 12 system that I am trying to configure with 3 IP addresses on one NIC card. I created scripts for each of the connections I want in /etc/sysconfig/network-scripts/ and they are called ifcfg-eth0, ifcfg-eth0:1, ifcfg-eth0:2. If I run /sbin/services network restart it configures everything as I would like. When I restart the computer the only device configured is eth0 and it is set to DHCP. If I run the script again everything works. What am I missing to make this change persistent?

View 2 Replies View Related

Debian Configuration :: Icedove Doesn't Seem To Exist

Apr 11, 2016

I have had to revert my VM to a previous image (did something to screw it up) anyway I have to reinstall icedove into my VM and I noticed after doing: sudo apt-get update && sudo apt-get install icedove that icedove can't seem to be found in the libraries anymore and simply wont install.

View 14 Replies View Related

Debian Configuration :: Can`t Log In - Keyboard Doesn't Work ?

Jun 8, 2010

I cant log in as user. My keyboard doesn't work, not even ctrl+f1. So i cant get dmesg....Only thing that is working is alt+print screen+REISUB.

When i booted in safe mode from grub i can log in but only if i enter my root password. And then do /etc/init.d/gdm start.

If i tray to continue straight to gdm in safe mode my keyboard is not working so i can`t log in.

Day before i notices`d that i cant log in with ctrl+f1. When i tray i get this masage madone-desktop login: madone /bin/sh : cant open madone

View 1 Replies View Related

Debian Configuration :: NetInstall Doesn't Works?

Jul 17, 2010

I bought a laptop : Samsung R580 and when i want to install Debian Squeeze with NetInstall, it's impossible because ma Ethernet Card isn't recognized.These are the caracteristics of my card :PCI ID : 11ab4381Supporté : YesFabricant : Marvell Technology Group Ltd.Matériel : 88E8059 PCI-E Gigabit Ethernet ControllerPilote : sky2The driver is not in the kernel 2.6.32 and i must to wait a new kernel version in Debian?

View 8 Replies View Related

Debian Configuration :: Wifi Doesn't Works

Aug 5, 2011

After to install Debian Sid, i can't to connect to my network. When i launch lsmod, ath9k is present so the module is enabled.I don't use network-manager-gnome, wicd and other, i modify myself /etc/network/interface. But even with this configuration, the wifi does not works.

View 3 Replies View Related

Debian Configuration :: Wireless In KDE Doesn't Work

Sep 10, 2011

I have an Atheros wireless USB dongle that will connect to my Wifi network just fine in Gnome but in KDE doesn't. I've read through the http://wiki.debian.org/WiFi/HowToUse and have installed all packages and tried all methods noted there but still can't get the wlan0 to work at all in KDE. Is wireless in KDE & Debian Squeeze useless?

View 3 Replies View Related

Debian Configuration :: MySQL Server Doesn't Start

Jun 18, 2015

Since upgrading from Wheezy to Jessie I have not been able to start the MySQL-server. When I do a "systemctl start mysql" I get the following answer on the console:

Job for mysql.service failed. See 'systemctl status mysql.service' and 'journalctl -xn' for details.
Entering 'systemctl status mysql.service' the answer is:
● mysql.service - LSB: Start and stop the mysql database server daemon
Loaded: loaded (/etc/init.d/mysql)
Active: failed (Result: exit-code) since Don 2015-06-18 18:35:41 CEST; 4min 1s ago
Process: 11272 ExecStart=/etc/init.d/mysql start (code=exited, status=1/FAILURE)

syslog and hostname.err don't show any pertinent messages.

View 4 Replies View Related

Debian Configuration :: DRI 3 Doesn't Work With IGP - Missing Packages?

Nov 20, 2015

So, as per Arch Linux's wiki, I tried to make some optimisations to the intel driver through setting it up in Xorg.conf (or as advised by that wiki article, in '/etc/X11/xorg.conf.d/20-intel.conf' ), but I've ran into trouble enabling DRI3. Here's my current config file:

Code: Select allSection "Device"
   Identifier  "Intel Graphics"
   Driver      "intel"
   Option      "AccelMethod"  "SNA"
   Option      "DRI"    "3"
   Option      "TearFree"    "true"
EndSection

So far everything works fine, I haven't seen any noticeable tearing, nor did I had any problems with any graphics-intensive programs I run, but there's a slight problem with the DRI3 part as indicated by Xorg's logs:

Code: Select all[    26.556] (II) Loading sub module "dri2"
[    26.556] (II) LoadModule: "dri2"
[    26.556] (II) Module "dri2" already built-in
[    26.556] (==) Depth 24 pixmap format is 32 bpp
[    26.616] (II) intel(0): SNA initialized with Haswell (gen7.5, gt2) backend
[    26.616] (==) intel(0): Backing store enabled

[Code] ....

First of all it still mentions the DRI2 driver, is this supposed to happen, or did something go wrong? Also it complains that it cannot find a file, which I can't figure out which package it belongs to, and taking a quick search around the interwebs hasn't produced anything useful...

The IGP is the CPU, which is actually a i5-4460... which according to Wikipedia it has a HD Graphics 4600 GPU.

View 3 Replies View Related

Debian Configuration :: Nm-applet Doesn't Start After (Testing)

Feb 22, 2016

After the latest update of network-manager-gnome to version 1.1.90-3 , I see that I have to start the nm-applet in Testing from a terminal, otherwise I can't bring up my wired connection.

The usual nmcli networking on command is failing to connect, also restarting the network-manager.service with systemctl doesn't do anything, the only way to connect at this time is indeed to manually start the nm-applet from a terminal.

I've also spotted this message in the logs:

Code: Select alltraps: nm-applet[1105] general protection ip error:0 in libgobject-2.0.so.0.4600.2

Could it be something wrong with my configuration (although , it worked before this update) or is it some bug in network-manager-gnome 1.1.90 ?

View 4 Replies View Related

Debian Configuration :: VirtualBox Doesn't See Any Network Settings?

Jun 3, 2010

I need to set up a little virtual network with Debian Lenny guests (the host is Debian Squeeze, but I don't think it matters). I installed Lenny in a VM and it works fine. Then I cloned the hard drive, garion@Laptop:~$ VBoxManage clonevdi Linux 1.vdi Linux 2.vdi created a new VM with exactly the same settings as the first one and booted the new disc. The problem is that there's no eth0 in the new VM, but it is in the original one. Also if I "unplug" the cable, dmesg won't notice anything. In the original VM it works fine. They both have the same virtual network card: PCnet-FAST III (Am79C973). I've also tried NAT as well as internal network settings.

View 2 Replies View Related

Debian Configuration :: The Network Doesn't Automatically Reconnect

Dec 9, 2010

I'm running squeeze testing. I have noticed an issue with the way NetworkManager acts when the wireless connection is dropped. I believe it should automatically reconnect but it immediately puts up a dialog requesting me to enter the wifi password. This dialog stays indefinitely until I intervene and click "OK" (the password from the previous successful connection is still there). I would think that something as basic as wireless networking should not require 24 hour human interaction to stay connected. I have considered a cron job checking the network status and restarting it if necessary, but there is a configuration change or something else I can do to resolve this.

View 3 Replies View Related

Debian :: Squeeze Usb Wlan Configuration Doesn't Work

Feb 14, 2011

My net-book is working properly with Debian squeeze 2-6-32-5-686, only the wlan does not work. After typing lsusb I have got the message: lsusb : Bus 002 Device 002 : ID 160a:3184 VIA Technologies, Inc. VIA VNT-6656 [WiFi 802.11b/g USB Dongle]

So I obtained the driver package : VT6656_Linux_src_v1.19_12_x86. I followed the instructions ( make install... ) - but the result is only a lot of error messages. Mayby I am using the wrong driver package for the squeeze kernel - I don't know.

View 9 Replies View Related

Debian Configuration :: Dual Boot Ubuntu/Debian: Debian Has Disappeared?

Apr 5, 2011

I have just installed Ubuntu (/dev/sda7) and Debian (/dev/sda4), but since I have updated all informations on Ubuntu, then Debian did not appear anymore on the grub list. There is an wiki I have found, but I an not really sure about what to do.

Here are the boot informations:
Boot Info Script 0.55 dated February 15th, 2010

Boot Info Summary:

=> Grub 2 is installed in the MBR of /dev/sda and looks at sector 488861020
of the same hard drive for core.img, core.img is at this location on
/dev/sda and looks on partition #3 for (,gpt3)/grub.

[Code]...

ps: on this file, it says that the /boot is installed on the MBR and /dev/sda3. I will remove the boot from MBR as I am now using /dev/sda3 instead. Sorry for my english

View 7 Replies View Related

Debian Configuration :: Root Doesn't Have Permission To Change Passwords

Jun 19, 2014

I installed Debian Kit on my Asus Nexus 7 tablet, and after following the installation tutorial I got it running except for I'm stuck on the step to create a new user. (btw link: [URL] .... )

Here's how it went (I can't copy&paste from my tablet so I have to type out everything...):

Code: Select allroot@android-6c40984c21c156ae:/# adduser paul374
Adding user `paul374' ...
Adding new group `paul374' (5000) ...
Adding new user `paul374' (5000) with group `paul374' ...
Creating home directory `/home/paul374' ...

[Code] ....

So since I read somewhere that selinux had some permission problem, so I did a few chcons:

Code: Select allchcon --user=u --role=r --type=init --range=s0 /etc/passwd
chcon --user=u --role=r --type=init --range=s0 /etc/shadow
chcon --user=u --role=r --type=init --range=s0 /etc/gshadow

And it did take effect:

Code: Select allroot@android-6c40984c21c156ae:/# ls -Z | grep passwd
            u:r:init:s0 passwd
u:object_r:unlabeled:s0 passwd-
root@android-6c40984c21c156ae:/# ls -Z | grep shadow
            u:r:init:s0 gshadow
u:object_r:unlabeled:s0 gshadow-
            u:r:init:s0 shadow
u:object_r:unlabeled:s0 shadow-

...but still same thing as what happened in the beginning...

Anyway my goal is to create and be able to log in to another user so that I'm not stuck running root all the time. (Which, as we all know, is a bad idea.)

If there's a way to manually create the user by editing a few files, and root still won't be able to change passwords, I'm fine with that, as long as I have another user. Whatever it takes to just get a non-root user log-in-able...

I forgot to mention that since this is the Asus Nexus 7, there is no removable media, so chrooting from another Linux machine isn't an option, and neither is removing an SD card to use a LiveCD on it.

View 8 Replies View Related

Debian Configuration :: 8.1 - Keyboard Doesn't Work On Resume From Suspend

Jun 19, 2015

I'm running Debian 8.1 KDE on a 2007 dv6 laptop. Model number is worn off. lol but the specs:

Intel i3 first gen m 330
4GB RAM
Intel (ironlake) graphics

First off, closing the lid to my laptop doesn't trigger suspend, or anything no matter what I set it to in power options.

I can suspend using "systemctl" or suspend from the "Leave" menu, but upon turning my computer back on, my touchpad and keyboard don't work.

Sometimes, my touchpad will start working after about 15 seconds, but the keyboard doesn't come back. I have to hard reset.

I have a feeling it's something to do with systemd, but I'm not super proficient in linux. Just an end user who is friendly with a terminal.

View 6 Replies View Related

Debian Configuration :: Postfix Multi-instance Doesn't Work

Jun 21, 2015

i created a second instance of postfix.It isn' t the first time that i made this procedure but with debian i had a lot of problem.I think that the problem is chroot configuration of postfix .In the first i had two problem smtp “fatal: unknown service: smtp/tcp” and the second instance was enable to make nslookup of domain.I copied the necessary file in /var/spool/postfix-second-instace and i solved the errors.Now the problem is that there aren't error in log file but connect to xxx.xxx.net[yyy.nn.yyy.yyy]:25: Connection timed out for all connection. and the email are all in defer directory and the second instance doesn' t send emails.

View 4 Replies View Related

Debian Configuration :: BCM4313 802.11bgn Doesn't Work In Jessie

Mar 27, 2016

Debian configurating, so I try to use wifi adapter, but it doesn't work. I have installed Debian Jessie from netinst CD. To reach perfect speed no options were selected. After I installed xfce4 and xfce4-goodies.I follow some different instructions and no dice. Wicd show me no avalable wifi connections. used Ubuntu 14, Ubuntu 12, etc. and I didn't have any problems with wi-fi connections. Some outputs of comands...

Code: Select allsatyva@meliorD:~$ cat /etc/debian_version
8.3
Code: Select allsatyva@meliorD:~$ lspci | grep 4313
02:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01)

[code]....

View 4 Replies View Related

Debian Configuration :: Squeeze X64 ThinkPad 61p Suspend Key Doesn't Work

Sep 28, 2010

I have Debian Squeeze x64 on ThinkPad T61p with standard 2.6.32-5-amd64 kernel. thinkpad_acpi loaded as module, suspend to RAM works fine from menu in KDE as well as by closing the lid, however machine doesn't appear to react on pressing Fn+F4 which should put it to sleep as well. I've read through thinkpad_acpi documentation and asked Google but so far can't find the solution. Can anyone, point me in correct direction?

View 6 Replies View Related

Debian Configuration :: Why /etc/fonts/local.conf Doesn't Take Effect

Dec 21, 2010

I have used /etc/fonts/local.conf to control how the fonts looks like in my laptop, which runs a Gentoo. In particular, I don't want anti-aliasing. I copied the file to my Debian desktop, but it seems the file doesn't take effect, even after reboot. Do I need to do something else to make it take effect?

View 5 Replies View Related

Debian Configuration :: Ssh Doesn't Work After Sending Reboot Command

May 2, 2011

last week while I was using ssh to the computer1 inside a NAT as usual, I made another tunnel from the computer1 that I was connecting to, to another computer2 inside that NAT (ssh 192.168.1.130) and after making some changes in computer2 I typed reboot. The computer2 rebooted but the tunnel totally hung and I had to kill it in my laptop. Since that day I haven't been able to ssh to the computer1 as I am used to.

Here is some more information:

debug3: authmethod_is_enabled publickey
debug1: Next authentication method: publickey
debug1: Offering public key: /home/une/.ssh/id_rsa

[code]....

View 3 Replies View Related

Debian Configuration :: Modify Boot Scripts To Boot Usb Device?

Mar 3, 2010

Without going into a lot of the reasons, I have a bootable program on a USB stick that i would like to 'boot' when debian is starting up (or after it completes, or whenever it makes sense to do it). My MB does not support a USB boot, I've removed the floppy and CD so I can add additional HDs (its a small box but well ventilated).

Another option I have is to use my bios 'network boot' option, but I have no clue how to use it and the only description in the mb manual says "Allows system to be booted over a network" In network boots, *usually* one is given an option of specifying a device address, and the network boot executes a boot protocol (e.g. bootp), and the boot image file is downloaded to the target, stored and run out of RAM. No evidence of this behavior is exhibited when the network boot option is selected in the bios...

View 2 Replies View Related

Debian Configuration :: Failed To Load Nouveau - X Doesn't See Intel Driver

Aug 27, 2015

Built a machine w/ i5-4440 & gtx 960. I installed xserver-xorg-video-intel & xserver-xorg-video-nouveau. Xorg -configure fails, so I added xorg.conf I found online, makes no difference. xrandr can't open display. startx of course fails.

Backstory: My plan was to dual boot sid + stable as fallback with shared partition. First installed stable and whether connected to mobo or gfx card, I couldn't get login on tty, it would just hang on errors. So I installed sid (this time using lvm to hopefully make partitioning easier) and while I get the "failed to load nouveau" errors on mobo, gfx card gives me a login screen.

uname -a
Code: Select allLinux 4.1.0-2-amd64 #1 SMP Debian 4.1.6-1 (2015-08-23) x86_64 GNU/Linux

lspci | grep VGA
Code: Select all00:02.0 VGA compatible controller: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor Integrated Graphics Controller (rev 06)
01:00.0 VGA compatible controller: NVIDIA Corporation GM206 [GeForce GTX 960] (rev a1)

[Code] .....

View 1 Replies View Related

Debian Configuration :: Built In Bluetooth Adapter Doesn't Find Devices

Oct 12, 2015

I've followed the guide at URL.... but my computer is unable to find any Bluetooth devices. Whether I'm using the command line or gnome-bluetooth, I don't get any results. If I plug in a cheap USB adapter, I'm able to connect and use the devices.My computer is a HP ProBook 4330s running Debian Jessie. And as far as I can tell the Bluetooth adapter is a Ralink rt3592 combination Wi-Fi and Bluetooth PCI card. The Wi-Fi works fine, but when i try to connect to a Bluetooth device, I get no search results.

View 9 Replies View Related

Debian Configuration :: Hibernate Doesn't Work After Recent Kernel Upgrade?

Dec 15, 2010

I recieve the following error:

Cannot find swap device, try swapon -a
/bin/echo: write error: No such device

If I type swapon -a, I get something like this:
swapon: cannot find the device for UUID=4d79c009-9464-41d5-9f78-90644bca9ba3

It worked great before I did the upgrade... I've upgraded to 2.6.37-rc5.

View 11 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved