CentOS 5 Hardware :: Unable To Use Dual Monitor With Intel Hd Graphics
Nov 26, 2010
I've installed CentOS 5.5 64 bit on a Dell Latitude e6410. This model only contains Intel HD Graphics, not the extra Nvidia card you could also buy in addition. The getinfo output can be found here:[URL] Initially X11 did not work at all (blank screen), but using hints from other posts in this forum I was able to fix this by editing the file xorg.conf using the vesa driver, although I still do not get the native screen resolution of 1200x800 (I alwas get 1152x768).
Now I want to add an external monitor (Samsung Monitor connected via DVI, screen resolution 1680x1050). Unfortunately as soon as I try to configure the dual head mode using the system-config-display tool after restart of the X server there will be the the blank screen again. I tried various drivers with no luck.Has anyone succeeded setting up dual head on an Intel HD Graphics machine? I understand that this hardware is quite new and and would be easier to set up with more recent distros, but I would like to stick to CentOS, but cannot wait for CentOS 6.
View 1 Replies
ADVERTISEMENT
Jan 27, 2011
I just installed Ubuntu 10.10 on my Dell Latitude D430 that I use at work. I have it on my desk docked going to a Dell LCD Monitor. When I go into the monitor set up it says Unknown for the monitor and Laptop for the actual laptop display. Also, I have very low resolutions for the "Unknown" monitor.
I am trying to resolved this issue so that I have better resolutions on the external monitor and then I can try to extend the desktop between 2 screens.
I found something online about adding the intel PPA and I did that, but now what. There is no xorg.conf that I can find for 10.10.
View 7 Replies
View Related
May 12, 2010
i'm trying since ubuntu karmic to set up a xorg.conf for a special purpose. I've a htpc connected to my tv. Intel GMA 4500, DVI->HDMI-cable connected, Lucid Lynx installed. When the machine boots with the TV powered on, everything is perfect. xrandr reports all valid modes on output "DP2". Without the TV powerd on, Lucid starts in the low graphics mode, with the funny zenity-message. So far, i managed to disable all useless outputs (VGA1, HDMI1, DP1, HDMI2), leaving DP2 enabled. I managed this by assigning outputs to monitors and adding Option "Ignore" "True" to the corresponding monitor-sections. My only remaining problem is, that the intel-driver reports no connected monitor on output DP2. The TV is connected, but shut off. Has anyone got a hint to tell the driver to ignore the presence of a monitor?
[Code]...
View 7 Replies
View Related
Jun 22, 2011
After 2 months without any problems, my second screen plugged on my laptop has stopped working. It works on my windows partition. When I start the computer, I see the login screen on both screens. When I enter the password, both screen turn to black. If I unplug the extra monitor, the laptop start normally.I'm on Ubuntu Natty, my laptop is a Thinkpad E420s with Intel HD graphics, i5 cpu, 4gb ram.
View 9 Replies
View Related
Apr 16, 2010
My new motherboard has built in intel G41 graphics card. Problem is under ubuntu maximum resolution is something like 1300 x 1024, in windows the highets working is something like 1900 x 1200.How can I achieve the maximum resolution or near maximum on ubuntu 10.04, also note that I have the same issue on 9.10.I looked for the xorg.conf to try and manually set the resolution but the file does not exist in 10.04
View 2 Replies
View Related
Nov 18, 2009
Does CentOS 5.4 support Intel Q45 graphics chip? If it does not support, How do I install the driver manually?
View 1 Replies
View Related
May 14, 2010
I'm trying to get dual monitors working on a fresh install of debian from the netinst install cd. I did not allow the installer to download any packages and then manually installed xorg gnome-core & gdm using apt-get.
The monitors are plugged into the onboard vga and dvi ports of my motherboard. I believe the chipset is intel.
At the moment the displays are cloned.
I don't know much about xorg.
This is my xrandr output:
View 1 Replies
View Related
Mar 17, 2010
I have a Dell Dimension 3000 with an integrated Intel 865g graphics card that I am trying to use in X on Centos 5.4 i386. The "810" driver (what Centos configures by default) works, but will not display at 1600x900. Strangely enough, it will actually work at higher resolutions such as 1600x1200, but 1600x900 fails, even with 915resolution and 855resolution. The "intel" xorg driver (included with Centos) locks up the entire machine when starting X, so thats a no go as well.
The "fbdev" driver works but, once again, won't display 1600x900, because that resolution doesn't work properly with the version of the intelfb kernel module that Centos bundles. Fedora Core 12 works perfectly fine at 1600x900 on the machine. I think that if I could get a newer xorg installation (or perhaps just a driver) going under Centos, it might fix the problem. I couldn't find any 3rd party repos containing such packages. I'd really rather run Centos on the machine, due to the package stability (yes, I see the irony here).
View 1 Replies
View Related
Aug 18, 2010
! I'm thinking of buying a corei5-660 on a motherboard with an Intel H55 Express Chipset. Does anyone know if it's fully compatible with OpenSUSE 11.3? I mean video (that comes from the processor, not an off-board PCI), audio (HD Audio), networking (Intel� 82578DC Gigabit), SATA Controller, USB, etc. I've tried to google but didn't find much info so I wonder if anyone is using or knows where I can find more info about it...
I have found this thread on the forums about the H55 chipset: Core i3 Intel Clarkdale graphic controller problem But the problems were facing on 11.2, I don't know about 11.3...
View 8 Replies
View Related
Jan 2, 2011
I've installed Suse linux 11.3 (kernel 2.6.34.7-0.5) on my brand new computer HP all in one 5130. Everything worked incredibly well : Wifi, wireless keyboard and mouse, sound, webcam.. There is only one remaining issue : I get a very poor resolution (1280x1024) instead of the 1920x1080 allowed by the screen. The graphic card is an intel chipset (HD graphics) integrated to an intel core i3 CPU. Here is (part of) the X11.org log :
Code:
X.org X Server 1.8.0
Release Date: 2010-04-02
[ 15.124] X Protocol Version 11, Revision 0
[ 15.124] Build Operating System: openSUSE SUSE LINUX
[ 15.124] Current Operating System: Linux linux-7xhd 2.6.34.7-0.5-desktop #1 SMP PREEMPT 2010-10-25 08:40:12 +0200 x86_64
[Code]....
View 9 Replies
View Related
Jan 27, 2011
I have been trying to enable compiz on my fedora 14, but when i enable the desktop effects the graphics just crashes and fedora freezes. When i type lspci -nnk | grep VGA for the graphics card i get:
I made alot of research on how to get Intel graphics work on Fedora, but couldnt find any solution
Same problem I had with Fedora Core 12 and 13.
View 5 Replies
View Related
Jan 11, 2011
I recently switched my desktop from Fedora to CentOS. On Fedora it auto detects my refresh rate at 85 Hz. On CentOS by default it only allowed 60 Hz. I looked at the /etc/X11/xorg.conf file and the display settings were:
[Code]....
View 1 Replies
View Related
Dec 24, 2010
I have Dell E6510 laptop with i5 CPU (Arrandale), Intel HD integrated graphics card (Ironlake), and 1080p display. I know other distros are also having problems with Ironlake but there are some work arounds.
Is there a way to install 5.5 on my laptop and have UI and 1080p resolution?
I have to say that 5.4 Live runs well - UI loads with correct resolution. With 5.5 live I get black screen.
View 8 Replies
View Related
May 16, 2010
i upgrade a machine running centos 5.4 to 5.5 this morning. After the update the X start i saw the pointer and a black backgroud only the desktop doesn't appear.The machine is a barebone with this configuration
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)[code]....
and i solved the black screen problem changing the driver for i810
Section "Device"
Identifier "Videocard0"
Driver "i810"
EndSection
View 2 Replies
View Related
Jun 7, 2010
I am trying to install nVidia drivers on CentOS 5.4 and it is requiring kernel-source
# lspci | grep VGA
01:00.0 VGA compatible controller: nVidia Corporation G98 [GeForce 8400 GS] (rev a1)
For the installation of kernel source, I have followed the steps on [URL]. I followed the steps under 2.1 and they worked for me. Now what can be done for the installation of the kernel-source package. When I am trying to install nVidia drivers, I am getting error, following are lines from installation log of Driver.
-> Tagging shared libraries with chcon -t textrel_shlib_t.
-> License accepted.
-> Installing NVIDIA driver version 185.18.31.
-> No precompiled kernel interface was found to match your kernel; would you like the installer to attempt to download a kernel interface for your kernel from the NVIDIA ftp site [URL]? (Answer: Yes)
-> No matching precompiled kernel interface was found on the NVIDIA ftp site; this means that the installer will need to compile a kernel interface for your kernel.
-> Performing CC sanity check with CC="cc".
-> Performing CC version check with CC="cc".
ERROR: Unable to find the kernel source tree for the currently running kernel. Please make sure you have installed the kernel source files for your kernel and that they are properly configured; on Red Hat Linux systems, for example, be sure you have the 'kernel-source' or 'kernel-devel' RPM installed. If you know the correct kernel source files are installed, you may specify the kernel source path with the '--kernel-source-path' command line option.
ERROR: Installation has failed. Please see the file '/var/log/nvidia-installer.log' for details. You may find suggestions on fixing installation problems in the README available on the Linux driver download page at [URL]. I want to install driver.
# rpm -q kernel-
kernel-2.6.18-194.3.1.el5.centos.plus
# rpm -q kernel-devel
kernel-devel-2.6.18-92.el5
kernel-devel-2.6.18-164.15.1.el5.centos.plus
kernel-devel-2.6.18-194.3.1.el5
kernel-devel-2.6.18-194.3.1.el5.centos.plus
# rpm -q kernel-source
package kernel-source is not installed
The nVidia Driver I am installing is:
NVIDIA-Linux-x86-185.18.31-pkg1.run
# uname -a
Linux harvey 2.6.18-194.3.1.el5PAE #1 SMP Thu May 13 13:48:44 EDT 2010 i686 i686 i386 GNU/Linux
Only reason to install the proper driver is to use dual monitor.
View 6 Replies
View Related
Nov 10, 2009
I have installed/enabled centosplus, by using the command: yum update kernel --enablerepo-centosplus
Now I seem to be unable to install nvidia-graphics. When I use the command: yum install nvidia-graphics, I get the error: package kernel-2.6.18-164.6.1.el5.centos.plus.i686 (which is newer than kernel-2.6.18-164.6.1.el5.i686) is already installed
The nvidia-graphics bit is coming from atrpms - the kernel is coming from updates. What exactly does this mean? Does it mean that nvidia-graphics has not been built for this version of the kernel (centos-plus)? I am hoping to use centos-plus, as I need the support for DVB cards.
View 8 Replies
View Related
Nov 24, 2010
I have repeatedly installed CentOS 5.5 64-bit on a Dell T3500 with an nVidia Quadro FX 580, in an attempt to get dual monitor support to work to no avail. Everything works fine when just one monitor is plugged in and I do not try to enable or plug in a second monitor. I have installed the Dell DKMS, and the Dell recommended drivers (from Dell site) on one installation, I installed the nVidia drivers (from nVidia site) on another, and have tried with what CentOS loads by default on another. The results are the same every time: When I reboot as directed I get a black screen. I can recover by hard shutdown and unplugging one of the monitors, but that doesn't solve my problem. Has anyone had a similar experience, or have any helpful guidance? I am not very Linux savvy. This is for multiple machines in a corporate environment.
Information for general problems.
== BEGIN uname -rmi ==
2.6.18-194.26.1.el5 x86_64 x86_64
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
centos-release-5-5.el5.centos
== END rpm -q centos-release ==
[Code]...
View 3 Replies
View Related
Oct 5, 2009
I've been trying to configure this wifi on CentOS 5 this whole weekend =(. Here's the details:I'm currently doing this link:
[URL]
I'm not sure if I've configured correctly mac80211, but here's what on my lsmod and other details, let me know what else you need:
[root@mortonlx morton]# /sbin/lsmod | grep mac
mac80211 117453 0
compat 7617 1 mac80211
[code]....
View 6 Replies
View Related
Nov 30, 2009
I'm a newbie to installing LINUX (was an Oracle DBA for many years) and I am having trouble getting the dual head function to work with my Sony Vaio laptop. I just select a generic LCD with the screen resolution that I want, but when I startx, I briefly get the login window (terminal), then everything goes blank and I have to unplus the samsung monitor and reboot to be able to have a screen again. I have tried the fn + f keys and that doesn't help.
Here is the hardware:
Samsung Syncmaster 2343BWX
Sony Vaio VGN-FJ170
Intel Graphics Mobile 915GM/GMS/910 GML Express graphics controller
I would like to use this laptop as:
Audio streaming from internet (so far not working on my local NPR stations)
Hooked up to KVM switch - using the Samsun monitor and an adesso integrated keyboard
Wireless network (that is working - but it took some doing....)
What files and logs I need to post I will do so, but if what I want to do is just not possible or a big hassle, please just let me know, and I will load windows. Although I really wanted one LINUX box in my home office.
View 1 Replies
View Related
Oct 22, 2010
This is a triple-monitor setup with two video cards, where the mouse pointer gets "stuck" if it tries to cross from one video card to the next one. It worked correctly in openSUSE 11.2 and doesn't work in openSUSE 11.3 with the same xorg.conf. This is a 64-bit openSUSE 11.3 with xorg 7.5-11.3 (the openSUSE prepackaged version). I've already tried NVidia drivers 256.53-16.1 (the openSUSE NVidia repository version) and 260.19.12 (the latest off of the NVidia website).
This is the same xorg.conf that I used successfully in openSUSE 11.2. I tried a new automatically generated xorg.conf using nvidia-settings and it had the same problem. This forum won't let me upload the relevant files, but here: [URL] is a tar-ball with my xorg.conf, Xorg.*.log, /var/log/messages, and the NVidia debugging output.
View 3 Replies
View Related
Oct 6, 2010
installing CentOS 5.5 on intel desktop board dh55jp?i cannot install the centos on it.. either python got an error or halt on loading the OS...
View 2 Replies
View Related
Apr 8, 2010
I have been using ubuntu for quite a long time, and for the first time, I am now unable to set nvidia drivers to work. I have just install ubuntu 9.10 amd64 on an AMD 64 athlong X2 with a GEForce 6500 nvidia card.
The only reason I need the proprietary drivers is to use two monitors.
I am going crazy, I have tested everything I have found on the web. I have tried all the nvidia drivers version, I have tried envyng, ... but nvidia do not work!!
I am trying Xinerama with nv, but it does not work either!!!
Here is my xorg.conf file in which I have tried to use nv driver to set dual monitor. X fails to load and it says that screen 0 is deleted, that devices are found but there are no matches in the config file. Any clue?
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/cyrillic"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
[Code]....
View 3 Replies
View Related
Oct 19, 2009
This is a repost of my initial problem, I need some one who knows what they are doing more than I too take a look at this command output and give some sort of direction/clue/etc on what I'm doing wrong or missing.
Is my xorg.conf missing some vital line(s) or setting?
My best guess is that i'm missing something to tell the Xserver to use both screens, as the Xorg.0.log does not talk about trying to bring up the intel display; but this is just a hunch.
I'm running kubuntu 9.04 with 2 monitors: on-board intel video and a PCI nvidia display: I am using my nvidia display fine, but still can not get my 2nd display (the intel) working. What the heck am I missing?
lspci:
Code:
Code:
View 3 Replies
View Related
Jan 15, 2011
just setup suse 11.3 , put on the Nvidia 19.29-22.1 drivers via yast , no kms is set in inetd , nomodeset on grub boot line etc... Even tried installing the driver " the hard way " dual monitors come up, setup xinerama to "Extend" my desktop , and the main monitor ( right side ) is good, visually the left monitor (2ndary) is good.. but whenever I move my mouse over to the left screen the mouse pointer dissapears, flickers along the right hand border of that screen... and if i move the cursor back to the original screen i have to really fight to get it back to the main screen....Copy of my xorg.conf , still very basic...
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 260.19.29 (buildmeister@swio-display-x86-rhel47-04.
nvidia.com) Wed Dec 8 12:27:27 PST 2010
[code].....
View 9 Replies
View Related
Jan 27, 2011
I just upgrade to F14 from F10 on a dual montor setup. Firefox behaives differently on F14 than on F10.
On F10 it followed the mouse pointer's location and show up on the correct monitor
When maximized at close, it is always displayed on the left monitor. When not maximized at close it will open on the monitor where the mouse pointer is located.
About minimize/maximize Firefoxe before closing and it seems to work in some case, but not for me.
View 5 Replies
View Related
Nov 19, 2010
I have a dual monitor setup in Ubuntu, with my main monitor on the right and the monitor I want to extend to on the left monitor, but I can't seem to get it to do this, it always has the 'desktop' on the left monitor and then extends onto what I want to be my main monitor. I have an ATI Radeon 4350 Graphics card.
View 1 Replies
View Related
Dec 10, 2010
Is there any way to put a dual monitor wallpaper on a single monitor configuration using desktop wall? Using only 1/3 or so per wall. Something that will have the effect like the scrolling wallpaper feature on Android/iPhone.
View 2 Replies
View Related
Jun 28, 2015
I just installed Debian 8.1 with Mate desktop environment. I have a laptop with Intel® HD Graphics 5500.When I try to play a game like Left 4 Dead 2 or Torchlight 2 I get extremely low FPS.I also have Ubuntu 14.04 Mate on another partition. The games run fine there.I don't understand why this big difference. Maybe I have to install or configure something..
View 4 Replies
View Related
Aug 18, 2010
i previously posted a thread http:[URL].. that was regarding gaming issue, but now i got a bigger issue. i installed Intel 2010Q2 graphics package from [URL].. i first upgraded xorg-x11-server and related packages and installed devel package using yum.. later i compiled and installed kernel 2.6.34 and other packages included on [URL].. i rebooted the system and it showed display driver unknown so, i used system-config-display --reconfig and it detects my mobile 4 intel chipset. and when i reboot, GUI won't load .. when services finish loading screen goes blank and harddisk light blinks at constant intervals and i can't switch from GUI to CUI either using CTRL + ALT + F2 etc [URL].. PS i am able to login into single user and change xorg.conf
View 6 Replies
View Related
Dec 13, 2010
Purchased a slightly used T61 Thinkpad via a client of ours at work last week. I've been really happy with it so far, dumped 4GB RAM in it and have Vmware workstation running on it and all is well except the graphics drivers.
According to LSPCI the machine contains the device listed below.
Code:
X displays just fine and compiz works out of the box, but I'm only getting around 59 FPS with GLXgears. I do like to play the occasional game and what not, so i'm really hoping to get this increased. I've heard of running Tremulous on this card, so I imagine it can do it.
Is this low for this card?
View 2 Replies
View Related
