I've got two USB webcams I'm trying to get running with CentOS 5.4 x86_64. I've downloaded and installed the gspca driver from http://mxhaard.free.fr/spca5xx.html. Running lsusb yields:
Bus 002 Device 003: ID 0ac8:307b Z-Star Microelectronics Corp. USB 1.1 Webcam
Bus 002 Device 002: ID 0ac8:307b Z-Star Microelectronics Corp. USB 1.1 Webcam
I am in the process of building a new server on an Asus P5QPL-AM motherboard and an Intel E8600 processor.explain to me the difference between the two versions and what would you recommend.Also, is there any advantage of SATA over IDE hard drives?
View 1 Replies View RelatedI have CentOS 5.5 installed with this uname -a result: Linux 2.6.18-164.15.1.el5.centos.plus #1 SMP Wed Mar 17 20:01:32 EDT 2010 i686 i686 i386 GNU/Linux.I am trying to use star to back up the machine, but it seems to stop before it has tarred all the files.Here is my star command:
star -c -FFFFF -xdev -sparse -acl -link-dirs -wtardumps -xattr -H=exustar -copysymlinks level=0 f=/backup/24-May-2010-Full/Full.tar -C / . This then runs for a short while, creates an archive of about 230MB and reports: star: Success. Error moving extended header '././@PaxHeader'.finished!
I am using this star release star 1.5a75 (i386-redhat-linux-gnu) and I have used .exclude on some my directories.When I check the files archived using -t, only a limited number of the files have actually been tarred.It is also reporting that this is a partial dump rather than a full dump.
My problem is that I'm trying to install CentOS 5.4 x86_64 DVD ISO on Supermicro X7SBI server with installed Adaptec RAID 3405 controller.
I created RAID 5 array and is working fine (adaptec status says Optimal) but I can't install CentOS to that array (1.5TB size).
Whenever I try to install with: linux dd
I'm asked for a driver, which I have downloaded from Adaptec site and extracted contents to USB drive (in installation found as /sba1) which has now a lot of IMG and some ISO files on it.
I try to load (I simplified names) RHEL5.img, CENTOS.img... with x64 names (one exact name: aacraid driverdisk-CentOS-x86_64.img) and I always get the error message: "No devices of the appropriate type were found on this driver disk"
This is going on for a week now and I can't find the right driver or something I'm doing wrong to get install done.
This is my first post, I hope I'm the the right place. I installed mysql mysql-server php-mysql perl-DBD-mysql libdbi-dbd-mysql via "yum install -y" on a server running CentOS 5.3 X86_64 The install completes successful with no errors, but once I start mysqld via "chkconfig --level 35 mysqld on" ; "service mysqld start" There are no errors in /var/log/mysqld.log netstat shows mysqld listening on 3306 and localhost is in /etc/hosts
[Code]...
I have an i5 Thinkpad running Windows 7 64-bit. VT is enabled in the BIOS. I have installed vmware server v 2.0.2 but am unable to install Centos 5.5 x86_64 as a guest OS. The steps that I followed are as follows:1. Created a new VM, specifying RHEL 5 64-bit as the intended guest OS (per vmware documentation - Centos is not available as a selection2. Downloaded all 8 iso files for Centos v5.5 64-bit3. Modified the CD/DVD drive to 'connect at power' and use an iso with the path pointing to the x86_64 iso 1 of 8When I power up the VM, the console window displays 'ISOLINUX 3.11 2005-09-02 Copyright (C) 1994-2005 H. Peter Anvin' and nothing else. The installation splash screen never appears. As a test, I downloaded the first of 7 iso files for the 32-bit version of Centos 5.5 and pointed the CD/DVD drive to that iso. In that case, the installation starts as expected. I would really like to get the 64-bit version installed and running.
View 3 Replies View RelatedI'm trying to get a Digi Edgeport/8 working under x86_64 CentOS 5.3. This is a USB to serial conversion box that takes a single USB port and breaks it out into 8 DB-9 serial ports. We're running the 2.6.18-128.el5 x86_64.
This box has worked fine on many systems for us from RedHat 7.3 to Fedora Core 5 from everything back to the 2.4.20 kernel up to 2.6.16.16. On the CentOS box, in /boot/config-2.6.18-125.elf, the following is set:
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
Which is all we've ever had to do in the past and plugging the box in to the system, it will auto-configure.
what I need to do to get this working in the CentOS 5.3 64-bit world??? Time is critical for this to get fixed!
i like to use my DVB-C Card KNC-One on Centos 5.5 x86_64. But i cant get it to work. on a 32 Bit Centos this is working like a charm. I tryed several different kernels together with the video4linux-kmdl
At the moment i am using this kernel: 2.6.18-194.3.1.el5.centos.plus
[Code]....
tell me to configure star sp742 printer with cash drawer for Centos 5.5
View 1 Replies View RelatedI am brand new to this forum! I have spent some time on other Linux forums but based on my usage of CentOS I figured that it would be best to come straight to the pros. I've been using CentOS for a while now, mostly as a web server. Actually I use it as the base and installed Parallels Plesk Control Panel.
Anyway I want to setup a VPN and so far I haven't found any real solid documentation on how to do that! Yes I could install DAG/RPM Forge but what I really want to know how to do it from scratch. What I mean by scratch is that I want to download the tar.gz package from openvpn.net and then build it as required. I don't know much about building or compiling a package so that is why I have come here for help! I am guessing that I need to compile openVPN with openSSL and probably a few other packages... I could use openSWAN but I don't want to.
In the system-config-display the system sees the video card but when you look in the Configuration tab it is running on the vesa - generic driver.I downloaded the latest driver from ATI for x86_64 Linux and after I ran it there was an error that it could not find X-server:
[root@coopers ATI-4770]# chmod +x ati-driver-installer-10-5-x86.x86_64.run
[root@coopers ATI-4770]# ./ati-driver-installer-10-5-x86.x86_64.run
Created directory fglrx-install.ob5679
[code]....
I'm having troubles using this not so new webcam. I didnt found any thread that have a problem like mine. In older kernel versions the webcam started working compiling and installing zc3xx module, but as far as I googled and lsmod this module now comes with default kernel. As I can see, the module itself recognizes the webcam, but fails in the process.Does someone have some idea of fixing? Should I report it to launchpad (and so, which section?)?
View 2 Replies View RelatedI have downloaded all files from [URL]... and burnt a DVD. How can I now install centOS 5.3 on my server/computer ?
View 4 Replies View RelatedIn windows if i want to see/search for ALL files i go to the search app and type in *.* (star dot star). what is the procedure in linux/ubuntu? what command is it? i want to see ALL files on my NTFS usb back-up drive.
View 9 Replies View RelatedToday, I try to update firefox by Package Updater but show error by bellow. "Missing Dependency: xulrunner >= 1.9.0.19-1 is needed by package firefox-3.0.19-1.el5.centos.x86_64 (CentOS5updates)"
View 6 Replies View RelatedI am trying to install CentOS 5.2, and the installation ran out of disk space after running for about 2 hours.I checked the FAQ, and it said 1.2 GB. The disk is 3 GB. The default install was selected, and I think that it checks for sufficient available disk space before installing. Still, it ran for quite a while before announcing that it was out of disk space.The Installation Guide is not very helpful, since there is a blank page where the disk space requirement is supposed to be. I just picked the default installation. A search of the forums on "not enough disk space" did not return much.
View 13 Replies View Relatedi wanna ask if it's possible to install centos on hard2 while am running centos on hard1 then after installation is complete boot from the second hard drive. i dont have physical access to the server, all i can is connect to it through SSH. so is it possible to install centos on the second hard drive from CLI! then boot from it?
View 1 Replies View RelatedI have a Dell E5400 laptop running parallels with guest OS of CentOS 5.4. My problem is when I'm connected via Ethernet all connections are good. When I go wireless, CentOS is dead via network connections. Now according to Dell, I have a DELL 1397 mini card as my wireless card. Searches on the web state that the dell 1397 is another name for Broadcom 43xx wireless card. So after following any information I retrieved from the forum on trying to get the wireless connection up, I'm still having problems. Here is the latest error trying to build a driver using the hybrid_wl software from broadcom:
make -C /lib/modules/`uname -r`/build M=`pwd`
make: Entering directory `/usr/src/kernels/2.6.18-164.15.1.el5-i686'
CC [M] /usr/local/src/hybrid_wl/src/shared/linux_osl.o
CC [M] /usr/local/src/hybrid_wl/src/wl/sys/wl_linux.o
CC [M] /usr/local/src/hybrid_wl/src/wl/sys/wl_iw.o
[Code]...
I am running a CentOS 5.5 system which does NOT support VT Technology, so I am unable to use Xen HV. I am very happy with OpenVZ other than the fact that it doesn't support Windows, only Linux.I'd like to have VMWare Server 2.x installed, but it appears that OpenVZ changes the Kernel to, in my case, 2.6.18-194.3.1.el5.028stab069.6. The default kernel on my system is 2.6.18-194.3.1.el5.i386.If I change grub to load 2.6.18-194.3.1.el5.i386, VMWare will work but OpenVZ will not. If I change grub to load 2.6.18-194.3.1.el5.028stab069.6, OpenVZ will work, but VMWare will not.If I try to run /usr/bin/vmware-config.pl while in the 2.6.18-194.3.1.el5.028stab069.6 kernel, I get an error of:
None of the pre-built vmmon modules for VMware Server is suitable for your running kernel. Do you want this program to try to build the vmmon module for your system (you need to have a C compiler installed on your system)?Using compiler "/usr/bin/gcc". Use environment variable CC to override.
What is the location of the directory of C header files that match your running kernel?[/usr/ src/ linux/ include]I'm so lost as what to do now..is there anyway I can compile both of the kernels together somehow?
I managed to install xdebug from pecl, using the php-pear package from Centos base.
However, when trying to install PHPUnit i get an error saying I need at least PEAR >= 1.8.x
Has anyone managed to get a later version of PEAR running on Centos please?
I have seen that is possible to boot from a USB stick and use a USB memory as hard drive.I have a server enable to hold 6 sata drives 3.5", But I want to use the 6 drives and make a Raid-5 setup for backups 5 -1 spare. /boot cannot be on a raid-5 level 0 or 1. But I want to have redundancy for my OS, them I can install Centos on a Raid-1 using 2 disk, which let me only 4 for the raid 5. I will run a backup I want to have a lot of space.
Using 4 disk for raid-5 2 TB I will have 6TB no spare, no spare is not a good option at least I will prefer 1 spare.Well, I was thinking, the server MoBo have USB support, if I open the box I can see the small entrances, If Centos let me installed on a USB memory drive, can I trust a USB memory stick?t night with bacula.
I need to upgrade from xen-3.0.3-64.el5_2.9 which includes xen 3.1 to something that includes >= xen 3.2
1. what happened to xen-3.0.3-64.el5_2.9 and
2. where I can get an rpm for a x86_64 box with a xen version >= 3.2?
I am trying to install the ATI 10-11-x86.x86_64 But I have problems attached the installation log file
[Message] Kernel Module : Trying to install a precompiled kernel module.
[Message] Kernel Module : Precompiled kernel module version mismatched.
[Message] Kernel Module : Found kernel module build environment, generating kernel module now.
AMD kernel module generator version 2.1
doing Makefile based build for kernel 2.6.x and higher
[Code]...
I found some information. [URL]... This guy is libvirt 0.8.3 But Centos 5.5 x86_64 using libvirt 0.6.3, how to upgrade to 0.8.3?
View 1 Replies View RelatedJust finished downloading the CentOS5.5 x86_64 DVD images (2 ISO's), and realize that I have almost run out of DVD-R's. First ISO is a perfect fit for the 4.7GB DVD, the second only is ~400MB. Wondering if there may be any issue if I burn the second one to a CD (which I have plenty). I guess it should be okay, but wanted to double-check.
View 2 Replies View RelatedI am trying to install a minimalistic centos 5.6 VM.I have pulled the necessary RPMs from the centos website, using the following command:
yumdownloader --disablerepo=* --enablerepo=CentOS-5.6-x86_64
--destdir=/tmp/transitRPMs/ --installroot=/tmp/transitRPMs/ --resolve kernel
vim-minimal wget yum dhclient grub rootfiles openssh-clients openssh-server sysklogd passwd star attr[code].....
I do not see any 32 bit packages in the /tmp/transitRPMS directory, which good, and that is is what I expected / want.I have also downloaded the repodata and images directory from one of the CENTOS mirros, from the 5.6 directory.I am using the netinstall CD to kickstart the VM and using my local HTTP repository , which I created using the RPMs pulled from the yumuploader command.When I try to install the VM, after the disks are formatted, the installer starts asking for missing i386 or i686 packages. This is happening in both interactive installs, where I select absolutely no package; and also in the kickstart installs, where I have specified @core for the packages. I am unable to understand this behaviour. It was not so in CENTOS 5.5 x86_64 bit. I do not want to install 32 bit packages on my 64 bit machine.
I have checked and double checked the .htaccess and httpd.conf to make sure everything is correct and I'm sure it is. I have AllowOverride set to All in the httpd.conf, Apache sees and is reading the .htaccess because I get a 500 Error when I put garbage text in the file. I'm lost now.
View 9 Replies View RelatedI can't update centos 5.1 x86_64 from updates Is the correct repository [URL]? But I found this dependency (nspr >=4.6.99 ) inside the [URL]. I need to setup these two repositories ?
#yum update
Loading "installonlyn" plugin
Setting up Update Process
Setting up repositories
[code]...
I suffered a kernel crash today - then noticed a newer kernel was available, so I updated to it.However, it's since crashed again! Here's the message - can anyone tell me what's going on, is this a known issue or is it bad hardware?
general protection fault: 0000 [1] SMP
last sysfs file: /devices/pci0000:00/0000:00:00.0/irq
CPU 2
[code]....
On my 64 bit Cent OS 5.4 servers/workstations, my Passive Mode FTP iptables rules constantly stop working. If I do a lsmod | grep -i ip_conntrack_ftp
View 3 Replies View Related
