OpenSUSE Network :: Npcfs Crashes If Copy Job Netware 5.1 Mounted Volume Via Ncpmount Tcp Or Ipx Is Done
May 23, 2011
After update 11.2 to 11.4 copy jobs from netware 5.1 volume to local disk linux system does crash after a couple of seconds. I might have to do if there a allot of small files in that job. If happend system reboot is required because unmount netware volume nor delete copied files to the local linux system is not possible. Recompiling ncpfs package not possible because error free source package ncpfs version 2.2.6 might not be availble.
May 22 19:31:03 jaci kernel: [ 4694.764721] ------------[ cut here ]------------
May 22 19:31:03 jaci kernel: [ 4694.764730] kernel BUG at /usr/src/packages/BUILD/kernel-desktop-126.96.36.199/linux-2.6.37/include/linux/dcache.h
I shared a few directories using samba which can be detected with XP or OSX over the network. However, when I try mount those folders this error occurs (OSX): 'Volume X could not be mounted'.I checked that smb as wells as xinetd is running and that the firewall ports are open (also tried deactivating the firewall with no success).
I am having a problem with Dolphin where if I am trying to view the files in an extra partition I have mounted it crashes. It only does it on partitions not usually mounted at start up. The error it gives is:
In mi fstab file I mount a smb file server at boot. The code is: //<ip address>/data /home/eng-2/NAS smbfs credentials=/home/eng-2/.smbcredentials,dir_mode=0775,gid=1000,uid=1000 0 0 Transfer rate to the server is approx 100 KB/s Whilst transfer rate from the server 16 MB/s If I mount it from Places>connect to server. Both to and from speeds are 16 MB/s. Why is it so slow when mounted through fstab?
I'm rearranging a bunch of disks on my server at home and I find myself in the position of wanting to move a bunch of LVM logical volumes to another volume group. Is there a simple way to do this? I saw mention of a cplv command but this seems to be either old or not something that was ever available for linux.
I use Suse 11.2. I mounted 5 folders from fstab. 2 of them work but 3 do not. The 3 folders that do not work let me enter them, and they let me see everything. I can even create or delete a folder on them, if I am just browsing with konqueror. The problem is that I have a program that will not read them. It's a program made for my company and apparently it will only read folders that have all of their permissions set to read and write. The program will read the first two because their permissions are set to Owner, Group, and Others, can view and modify content. (The network folders are all windows server 2003 computers). The 3 folders the program will not read are set to Owner can view and modify content, but Group and Others are "can view content" If I try to change those permissions even in root, it tells me that access is denied.
I have v 10.10 running the following (and I still have no idea how I got this all working). Myth, Squeeze server, X10 control system for the house, Virtualbox (where I run some windows stuff) and a general file and print service. It has 5 disk drives attached
1 - system disk 5- external usb to back up data to 2,3,4 - 2 tb drives in a raid config
I just restarted the server and the raid volume has not mounted. I looked in the webmin interface and the device is there but it doesn't seem to have the partitions attached. Again in webmin, the partitions seem to be on each of the drives. I used crash-plan to back up the data and music, but not the video, so I would prefer not to have to rebuild the lot if I don't have to. I really don't want to re build the lot out of my lack of experience with Linux. Is there an easy (ish) way of putting the raid back together to see if it's just dropped its config and the data is in tact (or can be rebuild from two of the three drives).
I have an iSCSI device that is large, ~17TB usable, and I've created an XFS file system at the device level. I mount the device no problem and am able to touch and remove files without issue. I start my application and within about 5-10 minutes I start seeing the following entries appear in /var/log/messages
when I mount DVD-ROM to some files from xterm, the systerm never responsed! I used this command: sudo mount -t iso9660 /dev/cdrom /mnt/cd I search some info from google ,some guys say these info may help ,but I don't understand why it cab be crashed when I mount the CD from DVD-ROM.
/etc/fstab /dev/scd0 /media/cdrom0 udf,iso9660 user,noauto 0 0 lrwxrwxrwx 1 root root 3 05-22 19:54 /dev/dvd -> sr dmesg |grep hd [ 9.126848] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS.
I mount the shared drives (on a Windows Server 2003) and I can access them from my home directory. Everything is mostly fine. But I also get desktop icons for the shared drives, which I don't like since I prefer a bare desktop. Sometimes I have deleted desktop icons from /usr/share/dist/... but these are not there.
I am trying to create a link to my windows xp workgroup where all my data is stored (I was surprised that linux could even see it!) I mounted a volume on the desktop apparently... that worked fine until I rebooted and it had disappeared. it was fairly annoying that I had to go back into the network and re-mount the volume. How can I get it to stay put, even after rebooting?
I have recently installed Debian on my NAS server. I have also configured Samba for sharing the home directory of a nas user i.e. /home/nas To this directory I have read/write from a windows machine using the nas user credentials.
When I mount my RAID partition /dev/md0p1 to the /home/nas directory, I then realize that all content in this directory (files and subfolders) is only owned by the root user. When trying to access from the windows machine the /home/nas directory, I do not have any write access, only read. I have tried both the nas and the root user credentials.
I have also attempted the change the ownership of the mounted RAID partition to the nas user with the -R recursive option, but I get for the internal files/subfolders an error "operation not supported".
How can I overcome this problem?
- Is there something not done properly in the /dev/md0 array definition (i.e. ARRAY /dev/md0 level=raid1 num-devices=2 UUID=bddf8b69:c97967b5:cb104784:7fef7cc3 )?
- Is there something not done properly in the /dev/md0p1 mounting (i.e. mount /dev/md0p1 /home/nas)?
- Should I do any extra configuration before the mounting etc?
I have a big problem with my home router / server. The symptom is an alomst complete death. The other computers in the house can use the internet, i.e., the PC is not completely dead, but actually routes. However, it suspends all direct traffic: SSH becomes irresponsive, SMB shares disappear, and so on. It cuts traffic even with a VMWare guest it runs. I can ping it, but that's about it.The worrying thing is that it starts slowly. In the beginning it will start by cutting SMB pipes. It will then become very slow, to the point it won't execute a "shutdown" command.Then I sometimes have flood on port X, "sending cookies". That is certainly due to the P2P program, but cold a sustained flood affect communications on the virtual network adapter vmnet8?And then it enters this catatonic state with no special mention on the log.
Upgraded from 11.2 to 11.3 without any issues. However the newer version of Firefox keeps crashing and bringing down 11.3! It's a complete system crash with absolutely no warning, although it looks like 11.3 is trying to send the TERM signal before the pc shuts down.I have other browsers for my work, and both Opera and SeaMonkey work perfectly.Konquerer also works perfectly.
Thinkpad Edge, Intel Version, OS 11.3, KDE 4.5.2after my notebook shut down (due to a low battery) when I was just using Knetworkmanager to add a new W-LAN connection, I can't start Knetworkmanager anymore. Terminal output is:
Code: ~> knetworkmanager Connecting to deprecated signal
etherape crashes on 11.4 while monitoring an interface on which services using the portmapper are running. It's fine with icmp, www and smb. As soon as I issue rpcinfo -p <host> from another machine or try to mount nfs3 or nfs4 shared, etherape crashes on the server . Did you experience similar issues?It occurs on the 2 64bit and 1 32bit machines running openSUSE 11.4. No problem at all under 11.3.
I have mounted samba volume and I need to have write permissions for every new folder that's being created (currently, by default, on every newly created folder i have only read and execute permissions).I tried changing umask, but with no effect on mounted folder, umask changed only for local filesystem. I tried mounting with umask option, but with no effect again.I'm using ArchLinux on this machine, and I installed samba using default package manager (pacman).
I'm running 10.04 server on a Mac G5 with 2 network interfaces, one pointing to my network (192.168.0.x) and the other to a local partner network (192.9.100.x) with which we share a network volume to give/take PDF files.My client environment is MAC OS X (from 10.4 to 10.6) and until now only one client (with 2 nics) was connected to that volume: we don't have layer3 switches to do static routes over the two networks, so I decided to use my Ubuntu Server Mac to do this (it's also my new syslog server...).
Nics are configured correctly, and the local share (192.168.0.x) is well seen by everybody.But, when I mount the remote volume (192.9.100.x) to THAT shared folder, nobody is able to connect to the samba share (that now lists the remote volume directory...). The MAC OS X tells "unable to unmount the volume". IP forwarding is also activated on /etc/sysctl.confHere is a part of my smb.conf file
i'm installing a Linux system just simply following guide by fellow friends comunity. Currently, my box are having 2 HDD with 35GB each capacity. Displaying in GNome (36.2 GB Encrypted Data). During installation, I'd selected :
*Remove Linux partitions on selected drives and create default layout *The "Encrypt system" option
I have setup a NFS-share from an SUSE Enterprise Server 10 SP1 This NFS-share i connect on my OpenSUSE11.2 64bits and mount is in /mnt
I can list files and directorys, but can't copy. It manage to "copy" some folders, but then it stop and say it cant copy tjhe files and ask to skip files. Only folders are copyed/created localy but no files.
Where is the problem? Is it SLES or is it my local OpenSUSE?
I have a windows partition mounted that will not allow me to load my kubuntu 10.10 meerkat. i can enter an older kernal but my older kernal says cant contact kded and all my kde apps will not work such as wireless networking and autp ip configurations. although i can run the internet in this kernal wired however manually putting my ip and other numbers in for wireless connection fails. all other kernals do not load because they say i have a ntfs drive mounted. so my question is how can i unmount this drive and make my kernal work again or how can i fix kded from crashing on my second kernal so i can use that one. i have already tried sudo unmount /media/windows and other simular commands i also tried a mounting app and reinstalling kubunt desktop also check disk on windows with clean shut down does not work either.
If this is the right forum i don't know, but I'm having a problem which crashes my home server when writing to Samba. Googling and a quick search in this forum didn't help me any further. Is there anyone with a clue what to do?When I write several hundreds MB to my Samba share from a Windows machine the machine crashes (both with Win XP and Win 7). The problem is reproducible, although the precise moment (about 1 minute) or amount transfered data varies (about 300 to 800 MB). Small writes go well.Reading about 5 GB from Samba to Windows went without a hitch.
Hardware: - Foxconn r10-s3 (includes Atom N330) with 2 GB RAM Software:
On a small network i have 3 WinXP computers and i've just installed a two new ones with Win7 pre-installed. As server i'm running OpenSuSE 10.3 and Samba with only one share. As i mount it to WinXP computers all get same volume serial number:
V:>dir Volume in drive V is AppDrive Volume Serial Number is 8CD5-975C
...and all Win7 computers get a diffrent one:
V:>dir Volume in drive V is AppDrive Volume Serial Number is A0D3-975C
We use application witch somehow only works when one/same volume serial number on a mounted drive is used.