Fedora Installation :: Use HPLIP-Gui But It Doesn't Even See The Printer At All

Jun 14, 2009

I did an upgrade using preupgrade program and it went very well. However, I have lost my HP 1020 printer. Can anyone assist with this. I tried to use HPLIP-Gui, but it doesn't even see the printer at all. The other problem is that I get the following message when trying to use Yumex:

Failure getting http://rpm.livna.org/fedora/11/i386/...ta/repomd.xml:
13:09:06 : --> [Errno 14] HTTP Error 404: Not Found
13:09:06 : Trying other mirror.
13:09:06 : Failure getting http://livna.cat.pdx.edu/fedora/11/i...ta/repomd.xml:

[Code].....

View 11 Replies


ADVERTISEMENT

Fedora Hardware :: HP Printer - HPLIP Driver In The Repo Doesn't Work Correctly

Apr 22, 2010

I recently had problems with my HP printer in Fedora 12, where as I never had a problem with it in any other distrubution.... For some reason, the HPLIP driver in the repo doesn't work correctly... I don't know why... but I kept getting errors with "error: Printer queue setup failed. Please restart CUPS and try again."

I tried every suggestion I found... which was installing extra dependencies, disabling firewall, disabling SELinux and a whole bunch of other stuff... but nothing worked... THEN finally I decided to use the HPLIP driver from the HP website... it was a .run file... and I executed it, and my printer has worked perfect eversince..... my question is.... has anybody successfully installed their hp printer from the hplip driver in the repo's..??? I don't know why it didn't work for me, and i've seen other fedora users complain of the same thing? maybe theres something wrong with the package? or its not pulling in a needed dependency? I don't know...

View 2 Replies View Related

Ubuntu :: Warning: Printer Is Not HPLIP Installed. Printers Must Use The Hp: Or Hpfax: CUPS Backend To Function In HPLIP

Feb 15, 2010

Deskjet-F4400-series
--------------------
Type: Unknown
Installed in HPLIP?: No, not using the hp: or hpfax: CUPS backend.
Device URI: usb://HP/Deskjet%20F4400%20series?serial=CN9C1CK70705C5
PPD: /etc/cups/ppd/Deskjet-F4400-series.ppd

[code]....

how do I get the printer installed in hplip? I can print but cannot scan. xsane will not recognize printer. Jaunty 64bit 2GB Ram 350GB HD

View 1 Replies View Related

Fedora :: Hplip Block On LPT Printer

Oct 15, 2009

I installed a LPT1 printer a hp office jet T65 to add this printer was requested hplip I install the software that should de printer driver, when I print a file the file remain only in processing it wont go forwarder then that.I hope I was explicitly enough.

View 3 Replies View Related

Fedora Networking :: HPLIP Port Settings - Printer Not Recognized

Aug 5, 2010

I have recently installed Fedora 13 on my netbook. I wish to use my HP Officejet via the HPLIP utility. The problem with this is that when I have the firewall turned on, the printer is not recognised at all during setup. When the firewall is switched off, the printer is recognised. The printer in question is an HP Officejet 8500a which is connected via Ethernet cable to a wireless router. I would like to know if there are any network ports (that's used by HPLIP) that I could 'turn on' in the firewall that could let my computer recognise the printer.

[Code]....

View 5 Replies View Related

Debian Installation :: When Connect The Printer, Doesn't Recognize Printer As The Photosmart B109 Printer For Unknown Reason?

Jan 3, 2011

I've bought a HP Photosmart printer, HP Photosmart wireless e-All-in-One printer - B110a and i've got a problem installing it properly. I'm using Debian 6.0 Squeeze. When i connect the printer, Debian doesn't recognize my printer as the Photosmart B109 printer for unknown reason. When i go to the site of HP and search for a driver, it directs me to this site:I've downloaded that latest hplip file as a .run file and installed it. My printer is recognized proparly, but when i try to print a colored image, it comes out black/white. Something is not crrect. Does anyone recognize this problem with this type HP printer?

View 7 Replies View Related

Ubuntu Installation :: Install Hplip To Enable Hp Printer Driver, Understood That 9.04 Is Obsolete And No More Support For It?

Jun 11, 2011

I have ubuntu jaunty 9.04 installed in my system(thats my only OS.. no dual boot). When I tried to install hplip to enable hp printer driver, I understood that 9.04 is obsolete and no more support for it. I want to upgrade now. Update manager shows '10.04' for uogradation but it seems I cannot jump from 9.04 to 10.04 without getting into 9.10.

View 2 Replies View Related

Hardware :: 10.10 Installing HP Deskjet 1000 Printer - Error "Printer Requires The 'foomatic-rip-hplip' Program"

Feb 6, 2011

I have Ubuntu version 10.10 and I'm trying to install the HP DeskJet 1000 J110a printer. I have HPLIP version 3.11 (the latest version I believe). The printer shows up but when I try to print the error message reads: Printer requires the 'foomatic-rip-hplip' program but is not currently installed.

View 2 Replies View Related

Hardware :: HPLIP - Printer Does NOT Work

Nov 4, 2009

I have Ubuntu 9.04, and a HP laserjet 1018 printer.

I install the printer using:

And when it ask me about plugin I give the path to it. (the 3.9.2 version of the plugin, because Ubuntu 9.04 has the 3.9.2 version of hplip)

well I install the printer, everything works perfectly. .... but, when I turn off the PC, and turn it on again, the printer does NOT work!, I send work for being printed but mothing happens , Ubuntu tells me that the job was printed but ... no case, my printer does not print it. I have to install it again since cero. what can I don to stop install it every time I turn off the computer ?

View 1 Replies View Related

OpenSUSE :: HPLip Stops Communicating With Printer?

Feb 10, 2010

Everytime I get HPLip working with my printer, it will only work until I shutdown the computer. On next restart, it no longer works and the only way to get it to work again is to delete the printer configs in hplip and re-create them!

View 2 Replies View Related

OpenSUSE :: 11.3 - Hplip Complaining (Set Default Printer)

Nov 15, 2010

Trouble with cups - Opensuse 11.3 x86-64
Hplip installed
prrinter = HP photosmart 4280
No way I can set the printer as default printer in cups as in 11.2. Now hp-device-manager. Part of hplip is complaining "set the default printer"

View 2 Replies View Related

OpenSUSE :: Change Some Settings Of Printer Using HPLIP?

Apr 30, 2011

When I try to change some settings of my printer using HPLIP it tells me to add myself to the lp an sys group. Is that safe ? What are those groups used for ?

View 9 Replies View Related

Ubuntu :: Printer Won't Work After HPLIP Upgrade?

Jan 27, 2011

I'm running Ubuntu 9.10. The Update Manager did an update to HPLIP, the Hewlett Packard Linux Internet Printing software, one or two days ago. When I went to print today, the HP Officejet 4500 printer showed up in Open Office when my mouse pointed to the printer icon. But, the printer wouldn't work. Then I noticed that the HPLIP Toolbox icon was moved from the Applications - Accessoires folder, to the System - Preferences folder. I reinstalled all the HPLIP software, using the Synaptic Package Manager. When I click on the HPLIP Toolbox & run the HP Device Manager, it says "No Installed HP Devices Found".I was a little surprised to see the software upgrade caused the HPLIP toolbox to move fromhe Applications folder to the System folder. Because of this, I suspect there may be a bug in the upgraded software? Is anyone else having this problem?

View 1 Replies View Related

Ubuntu :: HPLIP Option Not Present When Setting Up Printer?

Apr 20, 2010

I just built a system and put a fresh install of ubuntu 9.10 on it. I have two other systems with 9.10 as well. On both of them the printer (an HP Officejet Pro 7680 set up directly on the network) is shown as an HPLIP printer with a URI that starts with hp:/net/ . When trying to set up this printer on the new machine the option for HPLIP is not present and the URI starts with dnssd://. I can only set up as and LPD Network Printer or an Appsocket/JetDirect network printer. Yes I have the hplip stuff installed on the new machine. My main concern is actually using the scanner function with Xsane. The other two machines scan just fine, the new one can't find any devices. I think this must be connected with the lack of HPLIP functions. This is with the AMD64 bit version of 9.10

View 1 Replies View Related

Ubuntu :: Printer Software - Change From HPLIP To Brother?

Mar 9, 2011

I plan on changing brands in printer from HP to Brother in the near future. Will I need to completely remove HPLIP before installing Brother printer software pkg on Ubuntu 10.04?

View 6 Replies View Related

Debian :: HPLIP Network Printer On Lenny System

Oct 18, 2009

I just installed HPLIP using Synaptic package manager. One of the configure parameters (shown by 'hp-check -r') is

Code:

Am I correct in assuming that this means that a network printer will not work? Is there a way to override this while still using synaptic package manager? Would I then be able to use a network printer?

I have my eye on the HP photosmart plus B209A - and it looks like HPLIP supports it (there is a ppd file for it).

View 1 Replies View Related

Software :: Install The Printer Hplip Raises The Error ?

May 25, 2009

I have an HP printer - C4200 series; Works fine in Slackware.

I am trying to get it to work in mepis-8.

Last thing done: hplip and cups were both un-installed and re-installed with no errors

When I try to install the printer hplip raises the error:

Quote:

printer queue setup failed. Please restart cups and try again.

This was done more that once; the last time after removing and reinstalling both cups and hplip.

I tried to install the printer using cups and get the error:

Quote:

View 5 Replies View Related

Slackware :: CUPS And HPLIP Duplicating Printer Entries - 13.1

Jul 18, 2010

I have an HP Photosmart USB printer that I configured with HPLIP (which seemingly "exports" into CUPS). All is well until the printer is turned off and then back on again sometime later: somebody, somewhere automagically adds the printer to CUPS so that I have two, count 'em, printers defined.

Code:

Some UDEV rule, some other thing?

View 3 Replies View Related

OpenSUSE Hardware :: HPLIP With 11.2 64-bit - OfficeJet Pro L7680 - Don't Get The Printer To Work

Dec 5, 2009

after an update to 11.2 (from 11.1), 64 bit, I don't get the printer to work. I reinstalled the driver and checked in cups: it says that the printer is available and waiting for a job. When I send something to the printer, nothing happens. The priont job will be stopped immediately. The printer is properly connected: xsane finds the scanner, that is part of the printer, without a problem. The printer is also ok: I can copy documents, it just works fine.

[Code]...

View 9 Replies View Related

OpenSUSE Hardware :: 11.3 Hplip Printer Queue Setup Failed?

Jul 31, 2010

I just installed opensuse 11.3 and was configuring the printer (via http) as usually using the HP Device Manager. But this time I got these error message:Printer queue setup failed. Please restart CUPS and try again

These lines were generated in the error-log of cups:
E [31/Jul/2010:23:30:35 +0200] [cups-driverd] Bad driver information file "/usr/share/cups/drv/sample.drv"!
E [31/Jul/2010:23:30:35 +0200] [cups-driverd] Skipping "/usr/share/ppd": loop detected!

[code]....

View 9 Replies View Related

Slackware :: --current - Hplip Won't Setup To Network Capable Multifunction Printer

Mar 14, 2011

I'm wondering if anyone else has this issue before I send a note off to Slackware on this.

The --current hplip package can't seem to actually complete the installation of a networked hp printer that has the printer physically plugged into the network.

The hplip app initially does detect the device, then I click next, then it says installation failed as it can't connect to the device.

Perhaps I'm doing something wrong.

I am however able to build, and run an older hplip that --current used a while back and it works splendid for adding a printer over the network.

I'm using version hplip-3.9.4b-i486-1 but I know that's not a big help to the project.

View 6 Replies View Related

Fedora Installation :: Install Software File Hplip.run?

Mar 24, 2009

How to install software file hplip.run ?

View 4 Replies View Related

Ubuntu :: HPLIP Toolbox Doesn't Find QT4

Aug 25, 2010

i have troubles using various HPLIP applications (HPLIP toolbox, HP setup, HP systray icon) because it doesn't find QT4. However i have qt4 installed (at least i think so, there are quite a few QT4 packages available, and i can't a metapackage that will install everything needed but qt4core, qt4gui and a bunch others are instlalled. pyqt4 is installed.

View 4 Replies View Related

General :: HPLIP - When Turn Off The PC And Turn It On Again The Printer Does NOT Work

Nov 4, 2009

I have Ubuntu 9.04, and a HP laserjet 1018 printer.

I install the printer using:

And when it ask me about plugin I give the path to it. (the 3.9.2 version of the plugin, because Ubuntu 9.04 has the 3.9.2 version of hplip)

well I install the printer, everything works perfectly.....but, when I turn off the PC, and turn it on again, the printer does NOT work!, I send work for being printed but mothing happens , Ubuntu tells me that the job was printed but ... no case, my printer does not print it.

I have to install it again since cero. what can I don to stop install it every time I turn off the computer ?

View 1 Replies View Related

Fedora Hardware :: Parallel Printer CUPS Fedora 15 HP Doesn't Install Driver

Jun 3, 2011

This post is for an HP parallel printer but I think it should work for at least "some" other parallel printers.I am sure that someone smarter than me will follow up this post with a "well, just do this and that" and you will have your HP Laserjet 6P printer ready to go, but since questions litter the forums of MANY distros on how to get "at least" an HP parallel printer to work, I'll post this anyway.This may or may not work for you if you do not have an HP but you can try it.The install printer box will let you do an install for an HP Parallel and it asks for how it is to talk to it, through CUPS sock or "local host'. When we get through what I recommend you should chose "local host".

View 2 Replies View Related

Ubuntu :: Intermittent Usb Printer - Sometimes The Printer Prints Sometimes It Doesn't

Mar 24, 2010

I have a parallel port printer connected using usb->parallel adapter. Sometimes the printer prints sometimes it doesn't.

A job will go the print queue and then sit there for ages. Sometimes if I unplug and then replug the usb->parallel cable the printer will print other times it will print half the document then freeze until the cable was unplugged and replugged again.

The printer never shows up in the list using lsusb (only my usb mouse and scanner do).

The printer is an hp deskjet 690c and worked fine under WinXP through a normal parallel cable. The one thing I haven't tested (but will test tomorrow) is the usb->parallel cable in XP.

View 1 Replies View Related

Fedora :: HP Printer Doesn't Show Up In The CUPS Wizard

Apr 28, 2011

I have taken a break from using Fedora, but since getting my netbook Ive decided to dual boot with Windows 7 Started (warranty purposes) and Fedora 14 with Fedora as the default boot OS. Now Ive got my home network setup as follows:

Gaming laptop, Windows 7 Pro x64, external powered USB hub with 1.5TB HD with shared folders through windows share permissions and the HP Deskjet F2430 printer

Netbook 1, my wifes netbook, Windows 7 Starter, has 100% access to the windows shares and the printer.

Netbook 2, my netbook, Fedora 14 has windows shared folder access but no printer access. In Windows 7 Starter has access to windows shared folders and printer access.

All of them are wirelessly networked through my Linksys WRTG54GS thats flashed with DD-WRT Mega firmware. The only laptop that has a hardwired connection to the printer and HD is my gaming laptop. how to go about allowing this? My printer doesnt show up in the CUPS wizard.

View 14 Replies View Related

Fedora Hardware :: Canon S100 Printer Doesn't Print

Sep 6, 2010

F13 showing that Canon s100 printer is founded, installed drivers and everything seems to be OK. But when i try to print text, testpage of what ever, nothing happened. Installed system-config-printer 1.2.4-1.f13, same udev and libs. Cups 1:1.4.4.5.f13, libraries, php modules Here is the Error msg:

[code]...

View 14 Replies View Related

Software :: CUPS Installation / Shared Printer And Not Able To Access Shared Printer From Any Of Fedora Machine?

Jul 21, 2010

Installed fedora/configued samba, shared printer and i am not able to access shared printer from any of the fedora machine. I am able to access the printer /shared folder from windows machine. I dont know the process of cups installation.

View 1 Replies View Related

Fedora :: Borderless Printing With HPLIP?

Oct 31, 2010

Anyone knows how to do borderless printing with HPLIP? I have an HP Photosmart C5550. On XP it is able to print borderless (without the white edges on 4 sides) on letter size (both plain and photo paper),but in F13 I always have a white border (~5mm or 0.2 inch) on the 4 sides of plain or photo paper.

Some old postings around 2008 said I should
- run hp-toolbox
- select "Print Settings" tab
- choose "fullbleed" (eg. 1200dpi fullbleed) in "print quality".

When I tried to follow this posting, I see no "fullbleed" selection in F13. Did I miss anything?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved