I'm using testing/Wheezy 64 bit: after upgrading to the latest repository kernel (2.6.38-2-amd64) my WLAN card isn't showing up unless I do a "modprobe brcm80211" or add " brcm80211" to /etc/modules.
View 1 RepliesDebian configurating, so I try to use wifi adapter, but it doesn't work. I have installed Debian Jessie from netinst CD. To reach perfect speed no options were selected. After I installed xfce4 and xfce4-goodies.I follow some different instructions and no dice. Wicd show me no avalable wifi connections. used Ubuntu 14, Ubuntu 12, etc. and I didn't have any problems with wi-fi connections. Some outputs of comands...
Code: Select allsatyva@meliorD:~$ cat /etc/debian_version
8.3
Code: Select allsatyva@meliorD:~$ lspci | grep 4313
02:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01)
[code]....
So basically, complete linux noob here, dual-booted fedora 13 with windows 7, and fedora can't seem to detect either my wired or wireless, however i don't really care about the wired. After spending a few hours browsing forums and tutorials and the like, seems as if it is a driver issue, as in there is none. I have managed to find the files :
HTML Code:
broadcom-wl-5.60.48.36-1.fc13.noarch.rpm
kmod-wl-5.60.48.36-1.fc13.5.x86_64.rpm
[code]...
I'm having issues with my broadcom BCM4313 wireless adapter. Everything works just fine when connected (with additional drivers & Connman), but it takes about 5 minutes to connect to my network when i just started my computer! When resuming from hibernation it goes very quick though, so just when I boot my pc it's taking forever...This is what I found in the dmesg output:
Code:
[ 16.778057] eth1: Broadcom BCM4727 802.11 Hybrid Wireless Controller 5.60.48.36
[ 16.808768] type=1400 audit(1295859939.727:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=833 comm="apparmor_parser"
[code]....
I have an Acer Aspire One D255 netbook with opensuse 11.3 installed and after several painstaking days of tinkering I successfully installed the broadcom wl drivers, and now my wifi card is operational. However, i can connect to my wireless network, but still have no internet access. I have searched the forums and google for a solution but most issues I have found that are similar to mine have been resolved once the wl drivers and firmware where installed
View 2 Replies View RelatedI want to move to Slack, so I took a look around the web to see if it can give support to my wireless card but couldn't find any relevant info.Is it supported? Can be installed?
View 14 Replies View RelatedI have a PC104 running debian. I have 3 hard drives (in addition to the one booting) mounted in fstab by UUID. I use the options defaults,error=remount-ro. However, this means that when I boot with the hard drives not attached, I have to press Ctrl-D to bypass when the boot discovers the drives are missing. Is there a timeout commandoption I can add to fstab so that it automatically continues booting even if the hard drives are not attached? I could not find anything on a timeout command. (I tried adding timeout=1000 but no-random guess)
View 5 Replies View RelatedI am attempting to get my laptop wireless to connect to my router. Wicd sees my router, I enter the known good password, and it reports bad password. Configuring router without wireless security and attempting to connect with wicd without security fails also. Laptop wireless has worked with other another linux distro, and windows.
Environment:Squeeze installed to Dell laptop with wireless: Bus 003 Device 002: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth)
Wicd reports that it fails with this text:
2011/01/11 20:06:02 :: Putting interface down
2011/01/11 20:06:02 :: Releasing DHCP leases...
2011/01/11 20:06:02 :: attempting to set hostname with dhclient
2011/01/11 20:06:02 :: using dhcpcd or another supported client may work better
[code]....
A friend gave me an HP Mini 110 that I can actually use in some situations. I installed Debian 8 with LXDE. It runs well except for the expected lack of driver for the Broadcom 4312 wireless chip. I installed wl using the method shown at [URL] ....
It works fine except that it takes very long to set up WiFi at boot (1 min 30 sec or more every boot--this is a rather frail Atom processor) and the WiFi reception seems poor (65% from an excellent router at 25 feet).
I'm thinking of getting a Panda 300Mbps Wireless N USB Adapter (reportedly using the Ralink RT5372 chipset) and removing the Broadcom driver. I have 2 questions:
1. Could I expect the Panda not to slow my boot time so much? I'm not knowledgeable enough to tell whether there is stable kernel support of this device, although the manufacturer says repeatedly that it works with most Linux distributions.
2. To remove wl is Code: Select allmodprobe -r wl the correct approach?
I just installed fresh Squeeze to my new hpmini 210-1100 netbook. No wireless. I have checked and I have Network Manager installed already.
I also compiled and installed Broadcom driver from here[url]
I followed their instructions and compiled the driver. I did get a wl.ko driver and installed it insmod wl.ko after modprobe lib80211
I noticed after rebooting neither wl.ko nor lib80211 showed when i did lsmod. So I did modprobe and insmod again. Still no wireless. Here are output of some commands that I thought would be relevant.
lspci:
I see only 2 computer icon in the system tray but not the parallel bars. When I went to System>Administration>Network, I was not able to add my wireless network name. The Add button was grayed out.
I have just joined the Debian community, for the past 2 years I have been using Linux Mint (ubuntu), I am now using Linux Mint Debian 64. I have a Lenovo A700 ideacentre with a Broadcom 4313 WiFi card. I manage to get the card working, now I have a new problem. If I suspend the machine the WiFi will not connect on resume. Is there a simple command I can use to getting the connection restarted, or better yet a work around so it will restart on its own?
View 14 Replies View RelatedI have a Broadcom BCM4312 LP-PHY in this machine. I was informed theres an open source driver for broadcom cards (brcm80211), but it doesn't seem to support this chipset. In the spirit of Debian, is there another driver available?
View 2 Replies View RelatedI have a server with two NICs. I tried to bond their network interfaces together, but it bombed out and didn't work, despite the fact I copied the example 100% except for my own numbers for addresses, etc. I decided to go back to a single NIC and let the other unused for now, since I need to get this server running. uh. yesterday.
[Code]...
When I boot up, often times eth0 isn't listed in ifconfig. I'll see eth1, which is just an unused interface at the moment, but eth0 is no where to be found. If I restart the network service, bam. I'm good. Why is it not auto coming up?
I'm installing Squeeze on on a Dell Latitude D830 laptop with a Broadcom BCM4328 wireless network card, and I'm stuck on getting wireless internet to work. I have the 2.6.32-trunk-686-bigmem kernel. I run KDE and I have knetworkmanager installed to sort the network connections out. Unfortunately, knetworkmanager cannot find any wireless networks for eth2 (the wireless adapter). There is a wireless network, as other equipment can still connect to it.
I've installed the broadcom-sta drivers according to http://wiki.debian.org/wl. When I run iwconfig, I receive the following output: eth2 IEEEE 802.11abgn ESSID:"" Mode:Managed Frequency: 2.412 GHz Access Point: Not-Associated Bit Rate: 14 Mb/s Tx-Power:off Retry min limit: 7 RTS thr:off Fragment thr:off Power ManagementMode: All packages received Link Quality=5/5 Signal level=0 dBm Noise Level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 missed beacon:0
[Code]...
I tried installing the driver following the instructions in the link given below.
viewtopic.php?t=7949
But now also its now working either. After installing the outputs are given below.
[Code].....
I have this in my /etc/networking/interfaces file:
auto lo
iface lo inet loopback
iface eth0 inet dhcp
pre-up iptables-restore < /etc/iptables.rules
post-down iptables-restore < /etc/iptables.rules
but eth0 doesn't automatically come up. I have to do a "ifconfig eth0 up" and then do a dhclient eth0 in order to get an IP after each reboot.
I installed Fedora 12 on an Eee PC 1001HA. This laptop has a Ralink RT3070 wireless chipset, for which the driver is not yet in the kernel (still in staging I believe). However I downloaded the driver, compiled it, and installed it. AFAICT, it works fine.
One small obstacle remains: I am uable to get the network interface to come up automatically; I have to run # ifconfig ra0 up. Because of this NetworkManager never sees the wireless interface, making connecting to WAPs a chore.
I created a ifconf-ra0 file in /etc/sysconfig/network-scripts, and it includes the line ONBOOT=yes, but this doesn't do the trick.
I installed Debian Squeeze on a new Acer Timeline.
lscpci gave me this
I used the Debian Wiki [url] to get the wireless working, but it's not happening.
iwconfig gives this:
The Network Manager shows (under Wired Networks) ifupdown(eth0) - I've never seen the "ifupdown" here. Wireless shows as disabled.
When I boot I see a few of these:
But I get No DHCPOFFERS received. So, Wireless is disabled.
Allright peeps does debian updrade automatically or one has to go about it by self and is it recommended to upgrade or just to go about re installing with a new dvd?
View 1 Replies View RelatedI have PCI-device and driver for it - tmk1553b.ko
The problem is to make this device work i have to open terminal after system starts and write
Code: Select allcd /path/to/driver
sudo insmod ./tmk1553b.ko d0=1 t0="TAI" misc=1
But idea is that this PC will work without operator so driver must be loaded automatically. As i realized the solution is to make script but when i try google it shows me how and where to put this script but not how to make it. Also i've tried to put tmk1553b.ko to /lib/modules/2.6.32-5-686/kernel/drivers/misc but it doesn't work.
Debian 6.0.10 (squeeze)
Kernel 2.6.32-5-686
I am using Debian 8 with systemd. I noticed that eth0 it is not starting automatically.
During boot process, I see this message: a start job is running for LSB: Raise network interface
My wireless in fresh Squeeze install would not connect automatically. I have to click on the network manager and enter the root password to connect every time I start up. I have "Enable Networking" and "Enable Wireless" checked in the Network Manager.
System>Preferences>StartupApplications>NetworkManager --- checked
NetworkManager>NetworkConnections>Wireless>[mywifinetwork]Edit>AutomaticallyConnect --- checked
There are only 2 lines now in /etc/network/interfacesauto loiface lo inet loopbackWhat should I do to get the NM to look for and connect wireless automatically at start up
I'm running squeeze testing. I have noticed an issue with the way NetworkManager acts when the wireless connection is dropped. I believe it should automatically reconnect but it immediately puts up a dialog requesting me to enter the wifi password. This dialog stays indefinitely until I intervene and click "OK" (the password from the previous successful connection is still there). I would think that something as basic as wireless networking should not require 24 hour human interaction to stay connected. I have considered a cron job checking the network status and restarting it if necessary, but there is a configuration change or something else I can do to resolve this.
View 3 Replies View RelatedI have squeeze and I've created my own custum kernel. Howto configure grub 2 to boot with this custom kernel automaticaly?
View 5 Replies View RelatedI've an Blade 1500, sparc64 IIIi with 2 hard disks and 2go of RAM. The computer run with debian 7.7.0 and BSD (opensxce) for each hard disks.
1/ When it's run under BSD there are no problems, the uptime are on many hours.
2/ when it's run under debian with XFCE x-window, the uptime is 4 hours 30 minutes and computer reboot automatically !
Into the control panel i've deactivate the hibernation, screensaver and power management ! I want to find the files for manage the time down. I think that the problem is in XFCE window manager.
The router should handle everything automatically and transparently. All you need to do is make sure that the wireless Ethernet adapters in the laptops can "talk" to the wireless router.
View 4 Replies View RelatedI have to use pppoe because my ISP uses service names, and as far as I know the only program which lets me input a service name is pppoe (inside the pppoe.conf file). Networkmanager is buggy because it tends to disappear from the panel periodically and, worse, it doesn't reconnect (although the option is selected, it does reconnect only once).
So, for peace of mind I open a superuser terminal and enter "pppoe-start" and "pppoe-stop" to have everything I want (reconnects automatically, etc.). Now the question is: how can I have pppoe-start run at startup, automatically, without entering superuser mode, and without having a terminal open for this? Using Debian Testing (Wheezy).
I have an old computer and BIOS counts the time slower than real. So, how can I set my OS to update the time automatically using the internet? If it updated the time only during booting, it would be enough.
View 2 Replies View RelatedI would like to update my network setup.
Today, I have an ADSL box which is my gateway to internet (192.168.0.1).
I have a Raspberry pi (RPI) which I use as a dhcp & dns server (192.168.0.2).
Recently my mobile phone operator installed a 4G antenna beside my home, and the bandwidth and latency are much better with my mobile phone than with my internet provider (ADSL).
I would like to install a wifi dongle on my RPI (I would get wlan0 & eth0 interfaces)
When RPI detect my shared phone connection (tethering) I would like RPI to automatically route internet:
- from authorized devices on my network to my mobile connexion (wlan0 -> mobile phone).
- from other devices to the standard ADSL internet (eth0 -> ADSL box).
I don't want any device to use the shared 4G connexion, best would be authorized devices to be selected by MAC address. How I should properly setup such a network ?
I've recently been trying to restore a Debian installation back to it's previous state after a serious operation system crash. Efforts are largely going well however I've run into problems since reinstalling Wine. Previously I could execute a Windows executable by simply entering ./executable.exe in the bash shell but this no longer seems to work as now I have to include the "wine" command in front of the executable. how to configure Debian to automatically use Wine to execute using the ./executable.exe format?
View 1 Replies View Related