Debian Configuration :: No Wireless In Squeeze With Broadcom Card
Oct 30, 2010
I just installed fresh Squeeze to my new hpmini 210-1100 netbook. No wireless. I have checked and I have Network Manager installed already.
I also compiled and installed Broadcom driver from here[url]
I followed their instructions and compiled the driver. I did get a wl.ko driver and installed it insmod wl.ko after modprobe lib80211
I noticed after rebooting neither wl.ko nor lib80211 showed when i did lsmod. So I did modprobe and insmod again. Still no wireless. Here are output of some commands that I thought would be relevant.
lspci:
I see only 2 computer icon in the system tray but not the parallel bars. When I went to System>Administration>Network, I was not able to add my wireless network name. The Add button was grayed out.
I have this PC that came with W7 installed..i am removing it to install Debian Squeeze.I already have burned the 8 DVDs plus the Squeeze Kde CD.AFAIK, BCM 4312 is a proprietary driver, not shipped with Squeeze, but present as source in Unstable..I have already downloaded the files also... will the built *.deb be enough to enable my wireless, or to i still have to do it by hand. remove confilicting modules, build the module, insert it, put it in the corresponding filder. does the deb install do all that, or do i still have to do it, "the good 'ol way"?
I decided to start of with Debian. I'm having trouble getting my wireless connection to work. I think i need drivers or something, i can't make a wireless connection. And it is a bit difficult for me, as i am new to Linux, and I'm not sure what I'm doing when i am writing these commands.
My wireless card is a Broadcom Corporation BCM43142 802.11b/g/n
I have been using Raspberry PI a little, so i am familiar with the terminal.
I am attempting to get my laptop wireless to connect to my router. Wicd sees my router, I enter the known good password, and it reports bad password. Configuring router without wireless security and attempting to connect with wicd without security fails also. Laptop wireless has worked with other another linux distro, and windows.
Environment:Squeeze installed to Dell laptop with wireless: Bus 003 Device 002: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth)
Wicd reports that it fails with this text:
2011/01/11 20:06:02 :: Putting interface down 2011/01/11 20:06:02 :: Releasing DHCP leases... 2011/01/11 20:06:02 :: attempting to set hostname with dhclient 2011/01/11 20:06:02 :: using dhcpcd or another supported client may work better
i install devian squeeze with the netinstall iso, all work fine except for the auto-detect of my ethernet card.i have a mother asrock p4i45gv with an onboard ethernet card realtek rtl8139/810x family fast ethernet NIC.i try everithing, the ifconfig shows only lo, but ifconfig -a shows a eth0 any ideas?
I'm very new to Debian (and Linux in general), and am currently taking a Linux course at college... I'm trying to get Debian running on my MacBook Pro (late 2009 model) and it's been complicated but I've got the operating system installed on it... I'm just having a few problems, the biggest right now of which is my wireless card, which doesn't work. So, I found instructions on the Debian Wiki for getting the driver for it, but it's not compiled already and I have little knowledge of manually installing stuff through Linux...
I am moving over to debian from ubuntu, and the latest install is to an acer aspire one netbook, the wireless card seems to be working and I can see available networks and even connect to mine (with WPA encryption) via the gnome network manager, however opening a browser or pinging both local and external machines all fail. its as if the OS does not not know to use the card. The wired works fine.
If memory serves the card is identified by lspci as Atheros AR5007.
There is no reference to wlan0 in etc/network/interfaces.
I do not have that system on now and have to leave for work, but I can post any further info from conf files etc as required when i get home tonight... Just thought I'd post a quick description in case I'm missing something obvious...
I upgraded from lenny to squeeze on a notebook and I can no longer connect to the wireless network. The computer is an LG notebook and the network card is ralink rt2860. I am using Gnome and NetworkManager. The wireless key is WEP hex. It was working fine with lenny till before the upgrade. After the upgrade, the network card stopped working. So, I checked
Then I reinstalled the driver with apt-get install firmware-ralink wireless-tools Then the network manager tray started working again and saw the network, but cannot connect. It was trying to connect but timed out and kept asking for the password. It is the correct password. I tried deleting the old connection and recreated a new one in the nm. But still does not work.
Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
when it comes to openSUSE but I am earnestly trying. I installed the openSUSE OS on my HP dv6000 laptop, but it does not seem to recognize my wireless card (which is a Broadcom 4311).
I'm having trouble getting my wireless card (RNX-G300LX, from Rosewill) working with my Debian install. I had it working at one point in time, but (apparently) something has gone wrong, as it no longer connects. The network I'm trying to connect to uses WPA2. When I try to start up my wireless card as follows: # ifup wlan0
I get the following response: wmaster0: unknown hardware address type 801 wmaster0: unkown hardware address type 801 Listening on LPF/wlan0/00:1a:... Sending on LPF/wlan0/00:1a:... Sending on Socket/fallback
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 4 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 15 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 17 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 3 No DHCPOFFERS received. No working leases in persistent database - sleeping.
I have set up /etc/network/interfaces as follows: auto lo iface lo inet loopback iface wlan0 inet dhcp wpa-conf /etc/wpa_supplicant.conf auto wlan0 and /etc/wpa_supplicant.conf looks like this: ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=0 ap_scan=1 fast_reauth=1 network={ ssid="apt_102" scan_ssid=1 key_mgmt=WPA-PSK psk="mypassword" proto=WPA2 }
I should also note that running wpa_cli -i wlan0 tells me that it is "trying to associate" with my router, but authentication times out each time.
I use Debian Stretch and I've installed it twice with the same ISO on the same laptop. First just to test a few things, then freshly installed it again.
The first time the wireless card was named wlan0 (as always for me, I've never had another name), the second time though it was suddenly named wlp3s0.
How did this occur and may I change it back to wlan0?
A couple of days ago I asked why my pc changes the wireless card name.It switches between AR9285 ( right) and AR5008 ( wrong). Well, it is not the case. When system identified with AR9285,it loads ath9k and I can connect to the router. When system identifies my card as AR5008, no kernel module is present at all ( lspci -k). The wrong card name occurs only when system rebooted. If I gracefully shut down the system, it always comes up with a right name for the card( AR9285). So, how to force the system identify my card right no matter if I reboot or shut down?
I'm trying to install the driver for mi wireless card. The instructions say that to build the tar.gz file, I have to:
# mkdir hybrid_wl # cd hybrid_wl # tar <path>/hybrid-portsrc.tarhybrid-portsrc-x86_64.tar.gz
The third step i don't understand. I want the folder of the driver to be located in a folder inside home called "Programas" so what I did was to open the terminal, went su, and then did cd Programas. Then I followed instructions 1 and 2, but I don't know what to put where it says <path>.
I am currently trying to connect to internet through my wireless card, after half day's effort I reached to this point:
/******The following error appears in the dmesg kernel ring buffer output: ipw2200: ipw2200-bss.fw load failed: Reason -2 ipw2200: Unable to load firmware: -2 ipw2200: failed to register network device ipw2200: probe of 0000:02:03.0 failed with error -5*********/
I found a solution from Intel website saying that the problem might be: "firmware in wrong location or wrong firmware version". So I proceeded to download the firmware and placed it in /lib/firmware. Also I tried to use menuconfig to enable loading firmware via hot-plug, but I think I have done something wrong when I was configuring the hotplug and firmware.
dell laptop and went out on thenet looking for a solution for my failed wireless interface. i downloaded the firmware but then my interface still fails to come on after a reboot.
I chose to change my operating system from Microsoft Xp to Linux and finally chose Fedora to be my new OS.
After Fedora installation I got a problem that I cannot connect to my wireless network I used to using Xp, I think that my wireless card is not installed on Fedora because when I checked in the network configuration I found that the only installed adapter is the Ethernet Realtek for the wired connection.
My OS is Fedora 11.
The CPU Model name is : Intel (R) Core (TM) 2 Duo CPU T8300 @2.40 GHz, so I think that my architecture is x86_64.
My Network controller is : Broadcom Corporation BCM4312 802.11b/g
Aluminum Unibody macbook, the only aluminum macbook to date. It has a Broadcom chip in it and I installed the STA drivers. The first day it seemed to work fine. Then I noticed pages stopped loading. The max throughput I get is like 30KiB/s once in a while. Sometimes I see consistent speeds of 600B/S...this really sucks. Is there a fix or anything?
I was going to make the switch slowly to 10.10 full-time, but the wireless issue is bothering me. The keyboard brightness keys don't work natively, but there's a fix I saw but didn't have time to implement earlier. I like ubuntu but I don't like my wireless not working!
My wireless works perfectly with my university networks. But I have problem connecting to my house router. The first time I installed Ubuntu 10.10, it connected to internet and worked well. After a restart needed by nVidia driver, my house wireless stopped working while my university wireless still works. I have tried reinstalling the driver using System/Administration/Additional Drivers and manually
I'm new to Ubuntu. Today, I took my old Compaq Presario V3010US and gave it life with Ubuntu 10.04. The hard drive was erased and replaced with the Linux OS stuff. Ubuntu recognizes most of the hardware except my Broadcom wireless card. I find this to be a pain because i'm a newbie to linux stuff. Anyway, can anyone help me fix this? I thank you for your time reading this.
I'm thinking of installing Fedora 14 on my hp laptop, and need to know if this will support the Broadcom 4322AG wireless card it came with, will only probably use Fedora if the card is already recognized, or an easy gui install. This is the game changer between using fedora or linux mint for me
I finally gave up trying to configue the Broadcom 4311 card. I went and bought a Netgear WPN111 USB wireless adapter. I've looke for the drivers but I can't seem to find them.
I seem to be have issues periodically connecting to wireless networks with WPA. It'll work one minute, and then I switch my macbook back on after a period and it refuses to connect again. It's happened on and off on three different networks now.
An example of /var/log/syslog: Code: Apr 15 17:57:27 macbookpro NetworkManager: <info> Activation (eth1/wireless): association took too long. Apr 15 17:57:27 macbookpro NetworkManager: <info> (eth1): device state change: 5 -> 6 (reason 0) Apr 15 17:57:27 macbookpro NetworkManager: <info> Activation (eth1/wireless): asking for new secrets ..... Apr 15 17:58:27 macbookpro NetworkManager: <info> (eth1): deactivating device (reason: 0). Apr 15 17:58:27 macbookpro NetworkManager: <info> Policy set 'Auto eth0' (eth0) as default for routing and DNS. Apr 15 17:58:29 macbookpro wpa_supplicant[949]: WPA: No SSID info found (msg 1 of 4). Apr 15 17:58:29 macbookpro wpa_supplicant[949]: No network configuration found for the current AP Apr 15 17:58:29 macbookpro wpa_supplicant[949]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
I'm about to install OpenSuse 11.3 gnome on my laptop with ubuntu & vista in a dualboot, and wanted to make sure that the Broadcom 4322AG wireless card would be compatible with my laptop.
