Ubuntu :: Unreadable WD MyBook Terrabyte Drive On 10.04 LTS?
May 8, 2010
I've been using a WD MyBook terrabyte USB drive for several months with no problem. Several days ago, I used the "safely remove drive" option but then unplugged the cable before the removal process had finished.
Now when I plug the drive in, the WD SmartWave section of the drive will mount. This is additional software for Windows computers that came with the drive and that I don't use. The main drive itself, though, will not mount. The drive doesn't show up on the left side of a navigation window, either.
I can see the drive using Disk Utility. It is located at /dev/sbd. (a) mount this drive or (b) recover its data so I can format it? I'd much prefer (a), of course. Regarding my level of tech savvy: I've been using Ubuntu for a couple years, but I chose Ubuntu because it allows me to use Linux while still remaining relatively ignorant about things, which is my comfort zone.
View 1 Replies
ADVERTISEMENT
May 29, 2010
I try to use a usb pen drive. The usb pen drive show up under computer but not like a drive in geparted. When I look in the log file I find the drive
Code:
May 29 10:11:46 CQ60 kernel: [ 112.942602] scsi 6:0:0:0: Direct-Access
USBest USB2FlashStorage 0.00 PQ: 0 ANSI: 2
I do not know what this mean but it looks like the drive show up like a scsi and not usb or? I need a clue to get it work like a normal usb device.
View 4 Replies
View Related
Mar 8, 2011
I've a LaCie usb drive that seems broken. Not detected by nautilus or gparted, nothing at /dev/sdbX but still doing noise when I plug it. I guess it's an hardware problem but I want to be sure. Do you know some tricks to try to rescue my disk (make a final backup)?
View 1 Replies
View Related
Jul 19, 2010
I have a Seagate 1TB external USB 2.0 hard disk which contains 740 GB of data. Everytime I connect, it shows the memory occupied and the remaining memory(190GB)..but when i try to access the folders inside they read empty... nothing is seen in the folders.. I am unable to read any data from it or write to it... Same is the case with Windows When I run self-test in Linux ubuntu I get
Reallocated sector count
threshold: 36
Normalized: 61
Worst: 61
value: 6488
Current pending sector count:
Normalized:1
threshold: 0
worst: 1
value:2036
View 1 Replies
View Related
Dec 26, 2010
I installed Ubuntu 10.10 onto my laptop and got a new plug and play device that wasnt being read so I went to go and install windows onto my laptop and when I get to the screen to select my partition it says its unreadable or its not detected but when I restart it it works fine in loading ubuntu.
View 2 Replies
View Related
Dec 16, 2010
I had a set of rather unusual problems on installing a new 500Gb hard drive on my F14 system, I've solved them, but they were that unusual that I thought I should share them in case anyone else gets the same thing! I'd been experiencing intermittent faults on one of my drives, (lock ups for no reason, occasional boot ups that failed due to ' disk unreadable errors' and other odd errors). I assumed that the drive was failing, but it always showed 'Heathy' on disk utility! This was the disk with the OS on, plus my main 'data' disk had some bad sectors, so I thought I'd buy a nice big 500Gb and reinstall the whole system.
I backed up all my data to an external 'USB' drive, opened the case, (a big old under the table 'desktop', why do they still call them 'desktops'?) shoved in the new SATA drive and rebooted, intending to format the new drive to EXT4 and partitioning it before installing F14 again! OOOOOOOOOW! Major drive failure, missing OS, whole list of SDB errors! Control D, to reboot, BIOS only sees one drive; SDA (I have three, two IDE and one SATA) plus the one I just put in makes four. I go into BIOS and discover that it not only cant see any of the other drives, but my two DVD drives are missing too!
Now I've been building my own systems and mucking about with computers since before you could buy them, and Ive never seen a problem like this one! At first I thought the new drive had screwed my system, for on removal, the problem persisted! Then I noticed that the IDE connector in drive SDB, (the long 40 pin job) was just slightly out of line with the back of the drive, pushed it firmly in and what do you know, everything works! We moved recently and I think the vibration was enough to loosen the connector to give intermittent faults, and pulling the cables about to get the new drive in, pulled it out further......
View 10 Replies
View Related
Nov 10, 2010
I need to mount a drive over fiber channel. It's a 4 terabyte drive. We're using a paragon driver to access other volumes on the SAN in a similar way. Works fine. I mount the other volumes as mount -t ufsd /dev/sdd1 /mnt/VolumeName Works fine. This is also an ntfs drive. The error I get when I mount: mount -t ufsd /dev/sdg1 /mnt/VolumeName01 is NTFS-fs error (device sdg1): ntfs_fill_super(): Device has unsupported hardsect_size
View 1 Replies
View Related
Aug 14, 2010
When I inset my External Hard drive into my laptop it shows 27.3 gb occupied but doesn't show all the files. Also , this is happening only now.
View 10 Replies
View Related
Jul 22, 2010
I was reformatting my external when the power on my laptop went out. Now it will not show up.
View 1 Replies
View Related
Jun 10, 2010
Ubuntu 10.04 LTS on VirtualBoxVM
Western Digital MyBook Essential 2TB USB
Want to format and partition the external hard drive for USB storage for DD WRT (i.e. into ext3)The drive is MS-DOS (FAT32) - Using Disk Utility (MAC) i erased what was on the drive.It mounts properly and can be accessed on the Mac OS.Upon plugging the USB into the Mac, the drive does not show on the Ubuntu desktop.Under the USB icon (bottom right) it indicates no USB devices attached however the "Western Digital My Book [0175]" is greyed out.
Going "Places" > "Computer" Only "File System" visible.
GParted - Drive not visible (only /dev/sda)
Using the sudo fdisk -l:
Disk /dev/sda: 3221 MB, 3221225472 bytes[code]...
View 1 Replies
View Related
Jun 3, 2010
im having problems connecting mybook 2 with my laptop. Everything was ok and running perfectly and there was no changes in my laptop or upgrades and it stop working. I was not able to see the computers in my network then I fixed it I can see them but when I try to browse the files the OS tells me that is unable to mount location and failed to retrieve share list from server. The funny part is that if I go to Places>Connect to server and type my mybook ip address, my laptop can connect and I can browse the files. I really dont know what is the problem. My firewall is down so I dont think that is the problem. If anyone can help me with these because I know im able to connect to my mybook but i am unable to connect to any other laptop or my WD-Tv live.
View 1 Replies
View Related
May 15, 2010
I installed Fedora 12 from the Live CD and all is going well. Using most of the defaults, including Gnome.I can't see my WD MyBook World on the network. It came with software for Mac and Win, but for Linux, they just say contact your Linux Provider.
View 2 Replies
View Related
May 24, 2011
This is a problem I've been working at on and off for quite a long time now. I acquired one of these devices from a thrift store and eventually decided that the drives would serve better mounted in my desktop PC, rather than hooked up to a router where large-scale backups are made unbearably slow.
What I quickly discovered is that these drives don't want to appear to any OS. The Windows installer doesn't see them. My Linux distro (at the time) didn't see them. A GParted live CD didn't see them. DBAN didn't see them. The BIOS, however, saw them, so I banged my head against a few possible solutions.
Martin Hinner's blog seemed promising but didn't have the information I wanted. This blog only had disassembly guides/photos, and no info (that I was able to find) on actually getting the drives to work in a Linux system. I'd love to have an extra 4TB of storage in my desktop.
View 4 Replies
View Related
Jan 27, 2010
I installed Gentoo on my WD Mybook WE II and im forget/dont know the ssh password. I can access Public shared folder but there is no access to change it. Any idea? I need to log in to mybook via ssh to install anti virus on it.
View 1 Replies
View Related
Jul 24, 2011
Is there anyway to get a 2 terabyte NTFS partition mounted in Suse Linux? Would be better to just mount if possible so I could use the storage for both my Linux and windows pcs.
View 2 Replies
View Related
Jun 25, 2011
how to connect Western Digital MyBook 2TB USB external storage in ubuntu 6.10
View 2 Replies
View Related
Jan 5, 2011
Ubuntu 10.10, 32 bit.I've got a 2TB WD external disk which has USB 3.0, and I have a USB 3.0 PCIe card.Plugging the drive into the card has no effect at all. The drive powers itself up, but the kernel log is silent. A USB 2.0 flash disk works properly with the card, and the WD disk works properly plugged into a USB 2.0 port, but the combination of the 3.0 disk and the 3.0 card is completely nonfunctional, even when using a small extension cable to cut off the superspeed connection.
Searching suggested that this is because of a bug which would prevent superspeed from working, but should -not- cause complete failure (highspeed fallback should be OK). I tried the suggested fix for this anyway, which was to install kernel 2.6.37-020637rc1 (was 2.6.35-24-generic). This did not help my problem nor did it correct that endpoint error message.
View 3 Replies
View Related
Feb 3, 2010
I've recently installed the program Sparky for processing NMR data. When I start the program the text is unreadable. For example the top left pull-down should be labeled 'File' and instead I only see the two horizontal dashes in the 'F' and the right 2/3 of the 'e'. Yet the banners above the windows are completely normal. I have occasionally had similar problems with Matlab, but it's intermitant and less severe
View 1 Replies
View Related
Oct 19, 2010
So I set up my laptop dual boot with XP, now when I try to open text files, word docs, etc with get or doc files get error message with Gedit and with open office shows crazy unreadable characters?
View 2 Replies
View Related
Jul 6, 2011
Greetings. I'm running 8.04 ubuntu. I received a call informing me that all PDF files come up as gobbley gook. I am in my first year, and unfamiliar with ubuntu. Although I accessed the files through the server (Eunice) and they are all labeled as unreadable. When I attempt to open them with document viewer, I get the error message "unable to open. Unknown mime type".
View 1 Replies
View Related
May 2, 2011
Just upgraded from Maverick 10.10 to Natty 11.04 and went smoothly even with the new Unity desktop. But when restarted from shutdown, the screen was jumbled and was only just able to restart (the screen jumbled but could just make out the dialog boxes. Then logged in in safe mode. Ever since, have only been able to run in the 'old' Ubuntu without features mode. I have an oldish HP/Compaq nc6000 with 20Gig disk and 675Meg memory. How or what went wrong since it seemed to run fine just after the install.
View 2 Replies
View Related
Sep 3, 2010
How can I fix my unreadable sandisk sansa express 2 gb mp3 player? It wont work to other software.
View 3 Replies
View Related
Jun 18, 2010
I Installed Ubuntu x64 10.04 on an Hp HDX 16 with Nvidia 9600m video card. I am having an issue that the screen is very dim and it gives one a headache to read it for long periods of time, especially in a bright room. I can adjust the contrast and brightness from the nvidia control panel but I can never get it just right it will either look washed out or just muddy. Everything was fine in Windows 7 a day or so ago. Is this a backlight issue?
Any suggestions on how to proceed?
View 1 Replies
View Related
Jun 25, 2010
i recently got a hold of a macbook 3.1, installed ubuntu 10.04 on it(Single boot). When i got the macbook the OSX that was installed on it had some serious issues, so without the OSX restore disk i had nothing so i hopped on my friends macbook pro and dled Ubuntu burnt it to a disk and installed it flawlessly on my macbook 3.1. During that installation i did remove the old OSX partitions completely and created a new one for ubuntu(the whole HD). later i was able to find a OSX Leopard backup on the interweb so on my pc i downloaded tit and burnt it to a dvd. When i try to boot from startup i just get a blinking cursor it stayed like that all while i took a 2 hour nap. Note that from within ubuntu i could see all the files on the disk so thats issue number one
Number 2 is that im trying to burn a dvd from a iso in ubuntu and when ever i insert a blank disk it says its unreadable and when i try to eject it it gets stuck. i have to hold the mouse button while it reboots in order to get it out. Whats causing this? how do i fix these issues. Eventually i want to startover and put mac osx on there (for steam) and ubuntu for primary use.
View 2 Replies
View Related
Jul 6, 2010
I installed windows 7 over an existing xp partition and windows 7 made a 100 mb partition as some sort of windows swap space thing. This basically made my ubuntu partition unreadable, even with gparted. How to recover this data?
View 5 Replies
View Related
Aug 30, 2010
I have burnt a data DVD (containing mp3 files) from k3b with the default settings (filesystem: Linux/Unix+Windows). No Windows machine, and no DVD players recognize it. My linux machine can read it back, and a Mac notebook could also read it. What can be the problem? Does anybody have an idea? I tried disabling the RockRidge extension - the same result. CDs (burnt with the same settings) work fine.
View 2 Replies
View Related
Sep 19, 2010
Our school introduced this OS called UBUNTU. I actually liked it, very much. They gave me an installation disk named Ubuntu 10.04 LTS Desktop Edition. So I asked somebody to install it for me. But there were some problems before he could even completely finish the installation. So I was the one ordered to complete the installation. There were 3 choices on the 3rd or 4th step of the installation process. By hit-and-miss, I choose the second one. The process went on safe and sound. It was alright for me to loose windows 7 loader but not the files and programs inside it. After the installation was done, I then started to explore.
I cant find my old files from windows 7. The whole disk was occupied by Ubuntu. My friend told me that Ubuntu will only occupy about 4G of the Disk only.My disk has a capacity of 250G. So if that's the case, then it should have left a free space of 246G. But when I took a check on my disk's availability, it showed that there is 210G of Memory Left. I was then wondering if that big memory are my old files from windows 7. Another thing is that those files are unreadable. I cant even see those files even if I "show hidden files". Can they still be recovered or not? I choose to reformat my whole drive.
View 2 Replies
View Related
Jan 6, 2011
Have recently installed 10.10 x64 on Gigabyte H55M-D2h/Intel i5/4GB/Onboard graphics&sound and have trouble with some text display. When hovering over some apps, the "help" dialogues appear as black on black, and same for some right/left click dialogue boxes.
View 1 Replies
View Related
Jul 6, 2011
I've got a new installation of 11.04 server. Everything was apparently working just fine, and then the system hung. I rebooted, and everything looked good up to the login screen. After I typed my password, the screen started looking good, and then got all fuzzy and messed up (nothing was readable). The only way I could get anything back was to reboot. (I am able to work via ssh at the command line, though). As the graphics were fine before (using GDM), and since the GUI looks fine at the login screen, I know the system can do it.
I tried to find information on what might be going wrong, and haven't been able to find anything that fixes the issues. I thought there might besomething in my config, so I tried logging into another account on the system that doesn't have any user-level configuration, and got the same result (the machine's main purpose is to be a mail and file server). So it appears to me that something is happening to the graphics configuration after login when GDM loads. What I need to change?
View 7 Replies
View Related
Jun 13, 2010
I just dropped my laptop while it was on. It is a dual boot vista and Ubuntu machine (9.04) and Ubuntu was running at the time. The machine didn't go down and after I got done using it I shut it down normally. Now it will not come back up because grub is saying there is something wrong with the disk geometry. It did give me a command line, I forgot the exact error message but I can look it up if needed.
I tried plugging the hard drive into a different machine under a live cd but everything was in the lost and found folder (80 GB) and the folder was unreadable. I backed up the windows partition successfully using windows explorer and now have been looking at testdisk and Stellar Phoenix Linux Data Recovery ($80) for the Linux partition. I don't know if it is ext3 or ext4, I may have bumped it up to ext4 from the default ext3 during the install. Also a few files on the windows partition were unreadable, so the disk definitely has some physical damage. I'm getting a new one along with a back up system for sure after all this is over.
I got tired of figuring out testdisk so I let the paid app run its free test overnight to see if I could recovery anything before I bought it, but it got hung up on a sector halfway through.
Going forward I think I will try Photorec next and then testdisk again if that doesn't work. Does Photorec get almost all the normal office (doc xls), music (mp3) and video files (mp4) not just pictures?
View 3 Replies
View Related
