Ubuntu Servers :: Network Card Not Working?

May 10, 2010

so i just downloaded Ubuntu Server 10.04 and i'm very happy with it on my virtual machine... but when i try to install it on my actual server it fails.

When i went to install it, it told me that there was no network hardware detected or something like that. So i just thought i could install a driver for it later.

So other than that all went well. and im very happy but now i dont know how to install my network driver. The card is a LYNKSYS LNE100TX. i downloaded the driver software and burnt it to disk because i was out of floppys. (I like floppys better) and when i went to install the software it allmost worked but it said:

Code:
make: gcc command not found

I'm assuming that means i need to install gcc but didn't really know how to go about it having no internet.

View 6 Replies


ADVERTISEMENT

Ubuntu Networking :: Network Card Working On 10.04 32bit But Not Working On 10.04 64bit!

Jul 25, 2011

I had an Ubuntu Server 32 bit installation and everything was working fine. Now that I installed Ubuntu Server 64bit on a new drive in the same machine, the ethernet card is not working!! This is insane cause when I put the hard disk with the 32bit installation back and booting from it, the ethernet card is working without any problems but in the 64bits installation it is not shown at all using "ifconfig -a"

lspci output:

Quote:

02:00.0 Ethernet controller: Atheros Communications AR8151 v1.0 Gigabit Ethernet (rev c0)

How can I check which module is being loaded in the 32bits installation to try to load it manually in the 64 bits installation?

View 3 Replies View Related

Ubuntu Servers :: Airport Card On A Wireless Network - Couldn't Auto-configure My DHCP Network

Aug 13, 2011

I've installed the Ubuntu 10.04 Server onto a PPC G4 Mac just for the experience of setting up a server. During the installation process Ubuntu couldn't auto-configure my DHCP Network. I'm using the airport card on a wireless network. How can I manually configure the network once Ubuntu is installed.

View 6 Replies View Related

Ubuntu Networking :: Broadcom Corporation NetXtreme BCM5721 Network Card Randomly The Network Connection On The Server Will Stop Working?

Jan 29, 2011

I have a Broadcom Corporation NetXtreme BCM5721 network card on my server at work.Everything works fine for a few weeks, then randomly the network connection on the server will stop working. After it stops working, I will try to reconnect with the network manager, it shows a wired connection available, it shows the "connection in progress"animation, then the "connection disabled" icon.

I uninstalled the network manager and used manual configuration, but do you think the network manager was the issue? I can't have the server disconnecting randomly every few weeks with no way to know what the real problem is. Was there an issue with the network manager with 10.04?

View 4 Replies View Related

Ubuntu Networking :: Network Card Not Working / Get That?

Apr 21, 2011

I have BroadCom BCM4318 802.11B/G Wireless Card. When I first started Ubuntu a week ago it didn't work, but I fixed it after a day or two of googling it. However I made a mistake and uninstalled the Network Manager. I then reinstalled Ubuntu, but it wouldn't load the card again. I activated the driver, and restarted the computer, but then, since It was connected via Ethernet, it wouldn't reconize the Ethernet connection, but the wireless card it did, but wouldn't find a network that is supported.

View 6 Replies View Related

Ubuntu Servers :: Installing Network Card On Server?

Jan 7, 2011

im trying to use this as an ssh server but i need to some how install drivers for my WMP600N V1.1 network card from linksys. so how would i go about this.

View 9 Replies View Related

OpenSUSE Network :: DWA-125 Wireless USB Card Not Working

Mar 18, 2010

I have a dwa-125 dlink wireless card which will not work. This is my first time using OpenSuse 11.2 (Well OpenSuse period). I had the same problem with Ubuntu 9.10 as well. If it will help the solution I used with Ubuntu is here: [ubuntu] Dlink DWA-125 Wireless Card Issue - Page 4 - Ubuntu Forums. I'd rather use OpenSuse than Ubuntu.

View 4 Replies View Related

Ubuntu Servers :: Finding A Pcie X1 Network Card That Supports Tcp Offloading

Jan 18, 2010

my servers cpu gets woken up alot (acording to powertop) by eth0 when downloading files, i figured i could get a cheap pci card that supports offloading.

View 4 Replies View Related

OpenSUSE Network :: AR928X Wireless Card Not Working

Mar 11, 2010

I have a AR928X wireless card and everything I have tried has failed. The default driver ath9k scans and connects to my router but cant connect to any site or ping anything , same with the madwifi driver
lspci prints
02:00.0 Network controller: Atheros Communications Inc.
AR928X Wireless Network Adapter (PCI-Express) (rev 01)

View 1 Replies View Related

OpenSUSE Wireless :: Dynex Network Card Not Working / Fix It?

May 25, 2010

Well this my first time working with linux and openSUSE, and I love it. But one problem I can't overcome is my network card is not working. I went to bestbuy and bought the dynex enchanced wireless G card.
Model # dx-ebnbc
ver. 1011

I installed wine to run the .exe but that did nothing and gave me that the dll is not registered. openSUSE detects that the card is plugged in but the card does not light up or activate in anyway. The only way I can connect to the net is through an Ethernet cable.

View 9 Replies View Related

OpenSUSE Network :: Dynex Ethernet Card Not Working Correctly?

Nov 27, 2010

I have a hp zd 7000, i really like this laptop, the onboard ethernet will not work at all. i purchased a dynex wired ethernet pcmcia card to get on the internet with. i have had no luck getting on the internet with it it will light up so i am getting power but no transmitting light works at all i have three net work cards listed in the system. one is the wireless. and the other two are the wired eth0 is the onboard and eth2 is the dynex what can i do next to determine the problem i do not use the wireless at all.

View 1 Replies View Related

Networking :: Setting Up Network Card / Eth(n) Pairings, Not Working As Expected?

Mar 12, 2010

I haven't done a great deal of networking with Linux so bear with me if the solution seems obvious.I've got four machines with two Ethernet cards each; one on-board and one PCI. I'm trying to get it set up so that the PCI card is eth0, then the on-board eth1. This.. isn't going as easily as I would have thought. I expected I could just go to network configuration, switch to the "Hardware" tab... change the on-board card to be device eth1, change the PCI to be device eth0... then go to the "Devices" tab and change the nickname to match the device.

This has decidedly not worked at all. Additionally, on some of the machines that I haven't messed with, the device name for the PCI card isn't ethn, it's something like "Intelnnnnn" (some string of numbers that I don't have in front of me). Something more specific to the card I'm sure, but while I can assign that device a nickname, I can't use it.. I can ping -I Intelnnnn ip.add.re.ss, but I can't ping -I eth3 ip.add.re.ess.

Where am I going wrong here? I've looked at a few tutorials online but they look extremely more complicated (read_device_bus_id? qeth device?) than should be necessary for just what I'm trying to do

View 7 Replies View Related

CentOS 5 Hardware :: Realtek 8169SC Network Card Not Working

May 28, 2010

I am not very experienced using Linux but I never had big problems with Ubuntu. Now I am busy writing my PhD thesis and therefore I had to install CentOS to use one lousy program that I could not get to work under Ubuntu. However, it seems to be quite fine and it is working well besides one fact: The network card stopped working. In the beginning it was working fine although the speed was only on the level of 100mbit. The switch and the LED on the card indicated gbit connection, though. I tried to install the driver for the 8168 card which reduced the card to 100mbit (indicated by the LED on the switch and the card).

Ethtool indicated it was gbit capable but I couldn't activate it. After reading more and more I figured I have to use the 8169 driver again and live with the 100mbit. Unfortunately, after uninstalling the old driver and reinstalling the driver 8169 the network isn't working at all anymore. The network-manager displays the card as inactive and when I try to turn it on it complains about the wrong mac address, which I am not able to change to the proper one. I am using CentOS 5.5 with the latest updates.

View 17 Replies View Related

OpenSUSE Network :: Ethernet Card Wasn't Working - System Freezes

Dec 27, 2009

i have installed openSUSE 11.2 on a dell dimension 2400. My Ethernet card wasn't working, so i am using a wireless interface, but it doesn't work either. It worked on a dell dimension 4400, but when it gets to the activate network my system freezes. Should i re-install my system, or should i post this under the hardware category.

View 9 Replies View Related

Ubuntu Servers :: Get NFS Working On Local Network?

Apr 30, 2010

I've followed several guides and am trying to get NFS working on my local network. For starters, I think I should be able to NFS mount a drive on the server (192.168.1.65) TO the server. From there I'll work with another client (currently 192.168.1.80)

Code:
$cat /etc/exports
/media 192.168.1.0/24(rw,no_subtree_check)
$cat /etc/hosts.deny
portmap mountd nfsd statd lockd rquotad : ALL

[Code]...

The guides I've read seem simple, so I must be missing something easy. Can't figure it out, so I'm looking for help after googling for 2 hours.

View 9 Replies View Related

Ubuntu Servers :: Network Interfaces Not Working

Feb 26, 2011

I have been trying to set up Ubuntu server 10.04-2 and am a couple issues.

One issue is that the network interfaces aren't starting properly. I have to start them manually. I've tried to edit the /etc/network/interfaces with the following.

Code:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static

[Code]....

View 8 Replies View Related

Ubuntu Networking :: Wired Network Card Not Working - No "eth0"?

May 27, 2010

I recently installed Ubuntu 10.04 on an older PC and I'm having problems with the network card built into the motherboard. When I connect an ethernet cable into the ethernet port I get a solid amber light, and I can't connect to my router, (which is being directly connected). Nothing is shown in Network Connections, but on another PC with the same version of Ubuntu it shows "Auto eth0", and it works just fine connecting with the router.How do I fix this? I'm an Ubuntu noob so I'm not really sure what to do here.

The network card is an Intel 82547EI Gigabit LAN controller, and Intel's website offered a driver available for my kernel version of Linux. However I was typing everything it told me to do in terminal, (which half the time I have no clue what I'm typing actually means), but I ended up getting some errors towards the end of the install process. I'm not sure if I messed something up or the driver just isn't going to work.

I'm hoping there is an easier fix for this, I've been searching the net all night trying to find someone with a similar problem and I haven't found any. I think I have another ethernet card which I might pop in and see if that works....but I figure I'll most likely run into the same problem because I know for sure the motherboards network card works - has on Windows, I just can't get it working in Ubuntu.

View 9 Replies View Related

CentOS 5 Hardware :: Lspci Shows Lan Card But Lan Card Not Working

Jun 15, 2010

If i run lspci it shows lan card model, but lan card is not working. How do i check my lan card driver is installed or not?

Is there any way to list all installed drivers with hardware information like we have device manager in windows.

View 4 Replies View Related

Ubuntu Networking :: Wireless Home Network Is Not Recognized By Network Card (RealTek RTL8190 Mini PCI)

Jul 12, 2010

my wireless home network is not recognized by my network card (RealTek RTL8190 mini PCI). The post was as follows: "I am using a new computer with Windows 7 , Athlon quad core 2.60 64 bit, 8GB RAM. Internet conection works fine with ethernet but ubuntu does not see my wireless network. card (RealTek RTL 8190 ID: 10ec:8190). Have searched this forum but unable to come up with a fix. I was looking for windows XP drivers to use Ndiswrapper but could not find a list of .inf files. My network is OK and works perfectly in windows and with my 2 laptops. Can anyone point me in the right direction? Additional info: install was done within Windows using WUBI to a separate partition on my HDD. I am new to this and thouroughly confused as to the procedure for installing the drivers if they are in fact available."

I am very frustrated in that I would like to use Ubuntu 10.04 but it is useless without internet connectability. I am new to linux and do not understand where to get the appropriate drivers or how to install them. I wish someone would answer this post and either give me a clue what to do or just say "give up" and uninstall ubunutu.

View 2 Replies View Related

General :: Networking - Network Card - Connected To Network - Given Access Point - No Connection?

Apr 3, 2010

I installed the driver for my network card. iwconfig and ifconfig are all responsive to connecting to the network, I'm given an access point address. Then, I try to connect to a website and no dice. ping www.google.com yields no result. What gives?

View 2 Replies View Related

Fedora Networking :: Cannot Find Network Card While Setup Network Configuration?

May 25, 2010

Cannot activate network device eth0!"device eth0 does not seem to be present, delaying initialization".i cannot find my network card while i set up network configuration Now I use dual boot window 7 and fedora 9,I cannot find my network card in select network adapter while network configuration ,i have a network card Atheros AR8132 PCI-E fast Ethernet controller NDIS(620)and for wired in Accer laptop .

View 1 Replies View Related

OpenSUSE Network :: Suse 10.2 Network Card ( DG41RQ ) Configuration?

Jun 19, 2010

i am using intel hardware on this working on suse linux 10.2 . i am not able to configure the network card IP address I have tryed using dhcp and static both way. Currently intel DG41RQ network card is assembled in my system. by using command ifconfig i can see only lo but eth0 is not displayed their.

View 4 Replies View Related

OpenSUSE Network :: How To Connect Network Data Card To Run Internet

May 21, 2011

how to connect my network data card to run internet on openSuse..

View 4 Replies View Related

Fedora Security :: Switch Off The Network Interface But Light Of Network Card Plugged In The Router Stays On (green)

Dec 26, 2010

I have a laptop connected to the the net thru an adsl modem, when I switch off the laptop network interface,(thru system-config-network) the light of the laptop network card plugged in the router stays on ( green) where as in my pc, when i do the same thing , the light of my pc network card goes off in the modem

View 5 Replies View Related

OpenSUSE Network :: Set The Network Card MTU For Jumbo Frames?

May 13, 2011

How do you set the MTU on the network card for Jumbo Frames? The MTU drop drown only goes to 1500 which is far from the Jumbo frame rate of 9000. If I type 9000 in will it blow anything up?

View 5 Replies View Related

OpenSUSE Wireless :: Can't Connect To Network [network Card Seems To Be OK]?

Jan 12, 2010

i've installed openSuse 11.2 on my laptop (dell studio 15).Today at work i tried to connect to the wireless network, but i couldn't. First, the network card wasn't being recognized, but after a long time trying i was able to set it up, for this i used this command:

Code:
zypper in broadcom-wl broadcom-wl-kmp-desktop
So now, the networkmanager detects all the networks around, but i cannot (or i don't know

[code]...

View 8 Replies View Related

Ubuntu Servers :: Website Not Working \ Default Site Is Working?

Jan 19, 2011

I just installed the lamp stack and so far my default site is working. But a 2nd site I made is not working.I created the config file in /etc/apache2/sites-availableit reads:Quote:

<VirtualHost myip:80>
ServerAdmin webmaster@mydomain.com
ServerName mydomain.com

[code]....

View 9 Replies View Related

Ubuntu Servers :: After Some PHP Fatal Errors / Php Do Not Working / But Html Is Still Working

Mar 7, 2011

I have very interesting problem after ~10 PHP Fatal error, php 5(latest one) in apache2(latest one) in Ubuntu Server 10.10(with latest updates) just do not work. So if try any php page it's not working(user see white page), but HTML still work fine.What that can be? So only restart apache is help to back php. (we are running Wordpress blog 3.1)

View 2 Replies View Related

Ubuntu Servers :: .htaccess Working, Rewrite Not Working Properly?

Apr 25, 2011

I had a problem with apache2 and getting .htaccess working. I have done some things and i believe its working the ErrorDocument command is anyway. I believe there may be some problems with the rewrites though.Im trying to take a urlhttp://localhost/showthread/123and make it display whats on http://localhost/index.php?showthread=123The rewrite rule is Quote:

Options +FollowSymLinks
RewriteEngine on
RewriteRule ^showthread/([^/.]+)/?$ index.php?showthread=$1 [L]

[code]....

View 8 Replies View Related

Ubuntu Servers :: Two Network Cards / Can't Access Internal Network

Feb 25, 2011

I've installed Ubuntu Server 10.10 with two network cards. One for external, and one internal.My problem is that as soon as i activate eth1 (external), i can't access the server from the internal network (eth0)

With these settings i can't reach the internal network from inside.If i disable the gateway on eth1 and enable the gateway on eth0, it works.

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved