Ubuntu Networking :: Network Card Not Working / Get That?

Apr 21, 2011

I have BroadCom BCM4318 802.11B/G Wireless Card. When I first started Ubuntu a week ago it didn't work, but I fixed it after a day or two of googling it. However I made a mistake and uninstalled the Network Manager. I then reinstalled Ubuntu, but it wouldn't load the card again. I activated the driver, and restarted the computer, but then, since It was connected via Ethernet, it wouldn't reconize the Ethernet connection, but the wireless card it did, but wouldn't find a network that is supported.

View 6 Replies


ADVERTISEMENT

Ubuntu Networking :: Network Card Working On 10.04 32bit But Not Working On 10.04 64bit!

Jul 25, 2011

I had an Ubuntu Server 32 bit installation and everything was working fine. Now that I installed Ubuntu Server 64bit on a new drive in the same machine, the ethernet card is not working!! This is insane cause when I put the hard disk with the 32bit installation back and booting from it, the ethernet card is working without any problems but in the 64bits installation it is not shown at all using "ifconfig -a"

lspci output:

Quote:

02:00.0 Ethernet controller: Atheros Communications AR8151 v1.0 Gigabit Ethernet (rev c0)

How can I check which module is being loaded in the 32bits installation to try to load it manually in the 64 bits installation?

View 3 Replies View Related

Ubuntu Networking :: Broadcom Corporation NetXtreme BCM5721 Network Card Randomly The Network Connection On The Server Will Stop Working?

Jan 29, 2011

I have a Broadcom Corporation NetXtreme BCM5721 network card on my server at work.Everything works fine for a few weeks, then randomly the network connection on the server will stop working. After it stops working, I will try to reconnect with the network manager, it shows a wired connection available, it shows the "connection in progress"animation, then the "connection disabled" icon.

I uninstalled the network manager and used manual configuration, but do you think the network manager was the issue? I can't have the server disconnecting randomly every few weeks with no way to know what the real problem is. Was there an issue with the network manager with 10.04?

View 4 Replies View Related

Networking :: Setting Up Network Card / Eth(n) Pairings, Not Working As Expected?

Mar 12, 2010

I haven't done a great deal of networking with Linux so bear with me if the solution seems obvious.I've got four machines with two Ethernet cards each; one on-board and one PCI. I'm trying to get it set up so that the PCI card is eth0, then the on-board eth1. This.. isn't going as easily as I would have thought. I expected I could just go to network configuration, switch to the "Hardware" tab... change the on-board card to be device eth1, change the PCI to be device eth0... then go to the "Devices" tab and change the nickname to match the device.

This has decidedly not worked at all. Additionally, on some of the machines that I haven't messed with, the device name for the PCI card isn't ethn, it's something like "Intelnnnnn" (some string of numbers that I don't have in front of me). Something more specific to the card I'm sure, but while I can assign that device a nickname, I can't use it.. I can ping -I Intelnnnn ip.add.re.ss, but I can't ping -I eth3 ip.add.re.ess.

Where am I going wrong here? I've looked at a few tutorials online but they look extremely more complicated (read_device_bus_id? qeth device?) than should be necessary for just what I'm trying to do

View 7 Replies View Related

Ubuntu Networking :: Wired Network Card Not Working - No "eth0"?

May 27, 2010

I recently installed Ubuntu 10.04 on an older PC and I'm having problems with the network card built into the motherboard. When I connect an ethernet cable into the ethernet port I get a solid amber light, and I can't connect to my router, (which is being directly connected). Nothing is shown in Network Connections, but on another PC with the same version of Ubuntu it shows "Auto eth0", and it works just fine connecting with the router.How do I fix this? I'm an Ubuntu noob so I'm not really sure what to do here.

The network card is an Intel 82547EI Gigabit LAN controller, and Intel's website offered a driver available for my kernel version of Linux. However I was typing everything it told me to do in terminal, (which half the time I have no clue what I'm typing actually means), but I ended up getting some errors towards the end of the install process. I'm not sure if I messed something up or the driver just isn't going to work.

I'm hoping there is an easier fix for this, I've been searching the net all night trying to find someone with a similar problem and I haven't found any. I think I have another ethernet card which I might pop in and see if that works....but I figure I'll most likely run into the same problem because I know for sure the motherboards network card works - has on Windows, I just can't get it working in Ubuntu.

View 9 Replies View Related

Ubuntu Servers :: Network Card Not Working?

May 10, 2010

so i just downloaded Ubuntu Server 10.04 and i'm very happy with it on my virtual machine... but when i try to install it on my actual server it fails.

When i went to install it, it told me that there was no network hardware detected or something like that. So i just thought i could install a driver for it later.

So other than that all went well. and im very happy but now i dont know how to install my network driver. The card is a LYNKSYS LNE100TX. i downloaded the driver software and burnt it to disk because i was out of floppys. (I like floppys better) and when i went to install the software it allmost worked but it said:

Code:
make: gcc command not found

I'm assuming that means i need to install gcc but didn't really know how to go about it having no internet.

View 6 Replies View Related

Ubuntu Networking :: Wireless Home Network Is Not Recognized By Network Card (RealTek RTL8190 Mini PCI)

Jul 12, 2010

my wireless home network is not recognized by my network card (RealTek RTL8190 mini PCI). The post was as follows: "I am using a new computer with Windows 7 , Athlon quad core 2.60 64 bit, 8GB RAM. Internet conection works fine with ethernet but ubuntu does not see my wireless network. card (RealTek RTL 8190 ID: 10ec:8190). Have searched this forum but unable to come up with a fix. I was looking for windows XP drivers to use Ndiswrapper but could not find a list of .inf files. My network is OK and works perfectly in windows and with my 2 laptops. Can anyone point me in the right direction? Additional info: install was done within Windows using WUBI to a separate partition on my HDD. I am new to this and thouroughly confused as to the procedure for installing the drivers if they are in fact available."

I am very frustrated in that I would like to use Ubuntu 10.04 but it is useless without internet connectability. I am new to linux and do not understand where to get the appropriate drivers or how to install them. I wish someone would answer this post and either give me a clue what to do or just say "give up" and uninstall ubunutu.

View 2 Replies View Related

OpenSUSE Network :: DWA-125 Wireless USB Card Not Working

Mar 18, 2010

I have a dwa-125 dlink wireless card which will not work. This is my first time using OpenSuse 11.2 (Well OpenSuse period). I had the same problem with Ubuntu 9.10 as well. If it will help the solution I used with Ubuntu is here: [ubuntu] Dlink DWA-125 Wireless Card Issue - Page 4 - Ubuntu Forums. I'd rather use OpenSuse than Ubuntu.

View 4 Replies View Related

General :: Networking - Network Card - Connected To Network - Given Access Point - No Connection?

Apr 3, 2010

I installed the driver for my network card. iwconfig and ifconfig are all responsive to connecting to the network, I'm given an access point address. Then, I try to connect to a website and no dice. ping www.google.com yields no result. What gives?

View 2 Replies View Related

Fedora Networking :: Cannot Find Network Card While Setup Network Configuration?

May 25, 2010

Cannot activate network device eth0!"device eth0 does not seem to be present, delaying initialization".i cannot find my network card while i set up network configuration Now I use dual boot window 7 and fedora 9,I cannot find my network card in select network adapter while network configuration ,i have a network card Atheros AR8132 PCI-E fast Ethernet controller NDIS(620)and for wired in Accer laptop .

View 1 Replies View Related

OpenSUSE Network :: AR928X Wireless Card Not Working

Mar 11, 2010

I have a AR928X wireless card and everything I have tried has failed. The default driver ath9k scans and connects to my router but cant connect to any site or ping anything , same with the madwifi driver
lspci prints
02:00.0 Network controller: Atheros Communications Inc.
AR928X Wireless Network Adapter (PCI-Express) (rev 01)

View 1 Replies View Related

OpenSUSE Wireless :: Dynex Network Card Not Working / Fix It?

May 25, 2010

Well this my first time working with linux and openSUSE, and I love it. But one problem I can't overcome is my network card is not working. I went to bestbuy and bought the dynex enchanced wireless G card.
Model # dx-ebnbc
ver. 1011

I installed wine to run the .exe but that did nothing and gave me that the dll is not registered. openSUSE detects that the card is plugged in but the card does not light up or activate in anyway. The only way I can connect to the net is through an Ethernet cable.

View 9 Replies View Related

OpenSUSE Network :: Dynex Ethernet Card Not Working Correctly?

Nov 27, 2010

I have a hp zd 7000, i really like this laptop, the onboard ethernet will not work at all. i purchased a dynex wired ethernet pcmcia card to get on the internet with. i have had no luck getting on the internet with it it will light up so i am getting power but no transmitting light works at all i have three net work cards listed in the system. one is the wireless. and the other two are the wired eth0 is the onboard and eth2 is the dynex what can i do next to determine the problem i do not use the wireless at all.

View 1 Replies View Related

CentOS 5 Hardware :: Realtek 8169SC Network Card Not Working

May 28, 2010

I am not very experienced using Linux but I never had big problems with Ubuntu. Now I am busy writing my PhD thesis and therefore I had to install CentOS to use one lousy program that I could not get to work under Ubuntu. However, it seems to be quite fine and it is working well besides one fact: The network card stopped working. In the beginning it was working fine although the speed was only on the level of 100mbit. The switch and the LED on the card indicated gbit connection, though. I tried to install the driver for the 8168 card which reduced the card to 100mbit (indicated by the LED on the switch and the card).

Ethtool indicated it was gbit capable but I couldn't activate it. After reading more and more I figured I have to use the 8169 driver again and live with the 100mbit. Unfortunately, after uninstalling the old driver and reinstalling the driver 8169 the network isn't working at all anymore. The network-manager displays the card as inactive and when I try to turn it on it complains about the wrong mac address, which I am not able to change to the proper one. I am using CentOS 5.5 with the latest updates.

View 17 Replies View Related

OpenSUSE Network :: Ethernet Card Wasn't Working - System Freezes

Dec 27, 2009

i have installed openSUSE 11.2 on a dell dimension 2400. My Ethernet card wasn't working, so i am using a wireless interface, but it doesn't work either. It worked on a dell dimension 4400, but when it gets to the activate network my system freezes. Should i re-install my system, or should i post this under the hardware category.

View 9 Replies View Related

Ubuntu Networking :: Can't Get The Wireless Card Working?

May 13, 2010

I've installed 10.04 on a Dell 1200 laptop and cannot get the wireless card working. I've tried getting Ndiswrapper but it doesn't appear to be available on 10.04, and since I don't have an Internet connection, I can't download it. The card is a Broadcom Corp BCM4306 802.11 b/g. How do I get the card connecting to my Linsksys?

View 7 Replies View Related

Ubuntu Networking :: Wlan Card Is Not Working Any More

Dec 25, 2010

I'm a new user of Ubuntu and I think I need some help but let me mention before that I got this up working on a Debian system.My current kernel version is $ uname -r 2.6.32-27-generic.The problem is that my wlan card is not working any more such that my system freezes every time I enable networking with the hardware switch on my laptop.Therefore I bought a USB - WLAN stick and try to get this working.

Network Manager has the option "enable wireless" greyed out if I disable the hardware switch.If I enable the hardware switch and remove the module of my wlan CARD before (modprobe -r iwl3945) it says "wireless disconnected" for all networks.

View 1 Replies View Related

Ubuntu Networking :: Hp 530 Wired Lan Card Not Working

Dec 26, 2010

The wired lan card on hp 530 is not working the wireless works.

Code:

View 2 Replies View Related

Networking :: Network Has An Intermittent Fault - File Share Network Stops Working

May 7, 2011

Sometimes my file share network stops working,and will then work again.I'm lost with this problem. The server pc is a Zenwalk pc.The other pc is a win7 pc. This error only occurs on Zenwalk. When i run puppy from the live cd the file shares are always visible,without fail.Under puppy i use pNethood. When the ping command is used there is no problem, and the pc name can be pinged.This is shown below:

[Code]...

View 6 Replies View Related

Ubuntu Networking :: Network Card Not Detected?

Apr 4, 2010

I have bought a new laptop with W7 installed. And I installed dual boot with Ubuntu 9.10 on it.I tried to connect my laptop to Internet by Ethernet port. It works with W7, but Ubuntu doesn't detect my Network card .After some research on Internet, I suppose that it's a problem of drivers for this card.Here some parameters I could get :

>ifconfig :
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0

[code]...

View 4 Replies View Related

Ubuntu Networking :: Adding New Network Card

Apr 17, 2010

I've switched to a new motherboard, an Asus P6T SE one, and now I don't have any cable connections in Networkmanager anymore.

I see the new card when I run "ifconfig", it's called "eth2", but I have no idea where to go from here without messing up networkmanager.

View 1 Replies View Related

Ubuntu Networking :: Network Card Not Detected

Jun 16, 2010

I'm in serious need of some help. The network adapter on the motherboard of my main machine apparently failed about noon today. This machine serves as the firewall and router for my home office LAN, and so it has two network adapters, the second being a PCI card installed in the only PCI slot of the mobo. The mobo's adapter served the WAN while the PCI card serves the LAN.Since the mobo has only one PCI slot, none of the other PCI cards I have on hand could be used. Instead, I pulled an unused PCI-e dialup modem card from the machine, and bought a PCI express gigabit card to put in its place.

The problem is that the machine (running Hardy 8.04.4 LTS) does not recognize the new card at all. Running lspci shows only the old PCI card that serves the LAN. Similarly, running "sudo lshw" shows only the old PCI card together with a virtual adapter that's part of my VirtualBox installation on that system.I then dual-booted into Vista Home and attempted to install the new card there, using the CD that came with it. Vista detected the card and asked for the disk, but then was unable to find any drivers on the disk!The box says the card is from Star Tech, and the instruction sheet says its model is ST1000SPEX.If anyone can point me to the correct module to add to the startup list and/or remove from the blacklist, that may get me going again.

View 3 Replies View Related

Ubuntu Networking :: Set Up Dual Lan Card Within Same Network?

Jun 18, 2010

how to set up dual lan card using different ip addresses within the same network? for instance, i want eth0 to be 192.168.0.100 and eth1 to be 192.168.0.200 so that the bandwidth of each card could not be saturated easily. both lan card will be using the same gateway and dns which is 192.168.0.1. the eth0 could be used for mysql connection, while the eth1 could be used for samba connection for the entire network of 192.168.0.0/24.

is this possible?? i've tried but to my bad luck, it didn't work quite well, especially the connection to the internet.

View 2 Replies View Related

Ubuntu Networking :: Can't Seem To Get Network Card Up And Running

Jan 22, 2011

Hi, So brand new to Ubuntu and linux for that matter. Can't seem to get my network card up and running I have tried the various fixes through the forums, as you can see in the screenshots. Just hoping an expert could help me out so I can finally close the box and get sleep. I have a ASUS M4A78T-E with phenom II. I downloaded ndiswrapper (1.9) and have wicd. The card is trendnet 643PI but it shows up as RealTek 8190.

View 9 Replies View Related

Ubuntu Networking :: Network Is Working But Not Working?

Aug 28, 2010

OK so I set up a server yesterday and got ndiswrapper loaded on it with the appropriate driver, I edited the /etc/network/interfaces file to contact my router with it's MAC address, WEP Key, etc... So the problem is I can ping addresses like Google and Ubuntu Forums but I can't use apt-get to install or update packages. When I try sudo apt-get update I get a whole bunch of Code: W: Failed to fetch <address>Temporary Failure resolving <address>My Wireless interface is wlan0 and also I can ping my server from my other computer running Linux and my server can ping that computer too.

View 1 Replies View Related

Ubuntu Networking :: Get The Above Wifi Card Working As It Is Not Supported?

Jan 17, 2010

i was wondering how to get the above wifi card working as it is not supported.

View 1 Replies View Related

Ubuntu Networking :: Trendnet Wireless Card Not Working?

Feb 20, 2010

I have been trying to get my Trendnet TEW-649UB wireless card to work on Karmic. I have ndiswrapper "installed", but it doesn't seem to be working. I have reinstalled ndiswrapper-utils 1.9 and ndiswrapper-common from synaptic, but not ndisgtk (the GUI for ndiswrapper). When I try to see if any drivers are installed using terminal (ndiswrapper -i) the terminal freezes on me.

Previously I tried using the help doc for installing Trendnet wireless drivers, but I was met with no success. After my first try using the help doc it seemed that ndiswrapper was working correctly and the driver was installed, but when I tried to connect to my network my wireless was listed as "device not managed". If this helps at all the current state of my /etc/network/interfaces is: auto lo iface lo inet loopback

auto wlan0
iface wlan0 inet dhcp
When I run iwconfig I get:
lo no wireless extensions.
eth0 no wireless extensions.
pan0 no wireless extensions.

but when I try to install the driver using ndiswrapper -i I get the message: driver net8192su is already installed Right now my computer is not even reading that the wireless card is avaliable. When I left click on the network icon I can only see that I am on a wired network {ifupdown (wlan0)}. My computer is dual booted with Vista and the card works there, but for some reason I am having trouble with Ubuntu.

View 4 Replies View Related

Ubuntu Networking :: Get Card Working Without Being Connected To Internet?

Mar 16, 2010

I have to connect to my university's network. I was using ethernet through our router, but now I cannot do that. I recently installed the TRENDnet TEW-643PI and it works perfectly on the Windows 7 partition. Is there anyway to get the card working on Ubuntu without being connected to the internet?

View 2 Replies View Related

Ubuntu Networking :: Sitecom Wireless Card Not Working

Apr 4, 2010

I've just installed Ubuntu (Koala) on an old (but worthy) Toshiba laptop. It's got a Sitecom WL-140 wireless card. (BTW I'm new to Ubuntu, but an old hand at Solaris). Can't get the card to work, although I think It's nearly there. nm-tool shows driver is p54pci. The activity light shows an orange light occasionally. State is disconnected. I'm not really sure whether I should be using the supplied driver (p54pci) or the Windows driver for this card and ndiswrapper. I've installed the Windows driver with ndiswrapper thinking this may fix it but no.
ndiswrapper -l says wlancig: driver installed and device (1260:3886) present.

View 1 Replies View Related

Ubuntu Networking :: D-Link Air Wireless Card Is Not Working?

Apr 10, 2010

I have a D-Link Air DWL-520 wireless card on my desktop computer. It runs well with Windows, but doesn't seem to work with Ubuntu. I am using Lucid Beta 2. I have tried googling, but have not come across any clear solutions on how to make it work.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved