Ubuntu Networking :: Rt2860 / Rt2860sta No Longer Works After Upgrade To Natty?
May 16, 2011
I recently upgraded my Zepto laptop to Natty (11.04), and unfortunately the wifi no longer worked. I have a WPA net, and the combination with a Ralink chip seems unfortunate - judging from the number of internet posts.After browsing loads of threads on the 'net I think I have found a solution for 11.04 - it will work out of the box in 11.10 !
1) Add "blacklist rt2800pci" to /etc/modprobe.d/blacklist.conf
I think this makes the wifi stuff work as I can then do "iwlist wlan0 scan" and get reasonable output. But there is no integration with the Network Manager. So I have also done this (again, with inspiration from a few threads):
2) Edit /etc/NetworkManager/NetworkManager.conf - change the "managed=false" under "[ifupdown]" to "managed=true".
You may have to do a "service network-manager restart", restart or similar to get it going.It also seems I can suspend and get a wifi net connection upon wakeup.
View 1 Replies
ADVERTISEMENT
May 6, 2011
I've been happily using this lappie with LTS but wanted to try out 11.04. It looks great but wireless has been an issue:
1. No wireless during install
2. Had to manually blacklist the rt2860pci etc modules
3. Wireless still not resuming after suspend
05:00.0 Network controller: Ralink corp. RT2860
Subsystem: Ralink corp. Device 2790
Physical Slot: 0-2
Flags: bus master, fast devsel, latency 0, IRQ 18
[code]...
The latter manual mod improved things slightly but still no cigar
View 7 Replies
View Related
May 1, 2011
Long story short, my HTPC has a keyboard, but no mouse.I'd gotten pretty good at working the machine with no mouse, but after my upgrade to Natty Narwhal today, the Ctrl+Esc shortcut to open the Applications window no longer works. Alt+F2 only works when another application is already open.I can get to the Applications menu using Ctrl+Alt+NumLock and mouse emulation, but it's pretty painful.Have I messed something up here? My install went a little messy, but I've managed to get everything else working and I doubt a keyboard control would be a bad install/upgrade.
View 2 Replies
View Related
Feb 15, 2010
I recently upgraded from 9.04 to 9.10 and the sound on my machine no longer works. I was previously using the OSS for sound. I'd like the sound solution that requires the minimal effort and I don't necessarily need to run OSS again. Ubuntu is installed on a Dell Optiplex 960.
Code:
aplay -l
results in:
Code:
aplay: device_list:223: no soundcards found...
[Code].....
View 9 Replies
View Related
Apr 30, 2011
I have just upgraded to 11.04 from 10.10 and my wireless no longer works, the laptop is a dell inspirion 1501.
View 2 Replies
View Related
May 2, 2010
I had a working lirc using my hauppage card. After upgrade to Lucid, it no longer works. I don't see errors, but it appears to me is is not detecting the Hauppage card:
Code:
mythuser@PVR1:~$ dmesg | grep lirc
[ 19.761015] lirc_dev: IR Remote Control driver registered, major 61
[ 19.928886] lirc_i2c: chip 0x0 found @ 0x18 (Leadtek IR)
[ 19.928890] lirc_dev: lirc_register_driver: sample_rate: 10
[61920.300286] [<e086d654>] lirc_unregister_driver+0x44/0x160 [lirc_dev]
[61920.300289] [<e089a02b>] ir_remove+0x1b/0x30 [lirc_i2c]
[61920.300318] [<e089abc2>] lirc_i2c_exit+0x12/0x14 [lirc_i2c]
View 1 Replies
View Related
Jan 12, 2010
Before I upgraded to Karmic, I had Japanese text input set up on my system, but since the upgrade it no longer works. I can still read Japanese text, and when I press Ctrl+SPACE I still get the ANTHY box in the bottom right-hand corner, but Japanese is no longer on the list of supported languages. how to get Japanese back?
View 1 Replies
View Related
Jun 17, 2009
I was successfully using samba + fedora directory server in fedora 10 as a primary domain controller for my home network (achieved mostly by following barry905's instructions here: [url].
After upgrading to fedora 11, some of the pdc functionality no longer worked.
For example, when i ran 'pdbedit -Lv', i got:
Code:
I was able to fix this by adding to the [global] section in /etc/samba/smb.conf:
Code:
I also found that i could no longer join an xp computer to the domain. i discovered that for some reason, the samba administrator password had been cleared. after running:
Code:
That was fixed.
The last problem, which i have still not fixed, is that roaming profiles no longer work. when i try to do a domain login as user 'htpc' from an xp machine, i get the following message in xp:
Code:
Here's an excerpt of my /etc/samba/smb.conf:
Code:
View 14 Replies
View Related
May 28, 2010
When I run update manager, it gives me an error message saying:
Code:
This can be caused by:
* A previous update which didn't complete
* Problems with some of the installed software
* Unofficial software packages not provided by Ubuntu
* Normal changes of a pre-release version of Ubuntu
if I click partial upgrade, it looks like it did during the upgrade, then says:
Code:
There are no upgrades available for your system. The upgrade will now be canceled.
if I click close from the first "not all updates can be installed" dialog, it says:
Code:
It is impossible to install or remove any software. Please use the package manager "Synaptic" or run "sudo apt-get install -f" in a terminal to fix this issue at first.
running the suggested line gives the following output:
Code:
In Synaptic, fixing broken packages does nothing. Mark All Updates > Apply seems to work, but I'd still like to figure out why Update Manager does not?
View 7 Replies
View Related
Jun 17, 2010
my HUAWEI E160E Virgin Mobile no longer works after upgrade to Lucid it is detected but the connection no longer works. I tried deleting the connection and trying again but the modem is not detected in network-manager. The modem was working when i was using Karmic and still works on my UNR Karmic Netbook. I have tried various methods but I have not been able to get it to work.
View 1 Replies
View Related
Jan 5, 2011
Since I upgraded to 10.04 and ran Computer Janitor, the Xiphos Bible Guide no longer works. The splash screen comes up for a second and then disappears. I've tried removing and re-installing the program to no avail.
View 3 Replies
View Related
Jan 8, 2010
I just updated my system to a new kernel with the update manager and now my WICD no longer obtains an IP address. Everytime I try it says "Connection Failed: Unable to get IP address".It was working fine before and even when I reboot into an older kernel it still doesn't work.I'm using a Belking Wireless G adapter.I would have tried downloading another network manager but since I can't even access the internet I'm stuck with changing current settings and nothing seems to work.
View 4 Replies
View Related
Oct 16, 2010
Ubuntu, been using windows for years and now use Mac. I have Ubuntu running on a netbook at work and all of a sudden my wireless connection not only doesn't work, it doesn't seem to exist! Wired still works fine, but the wireless option has vanished. How do I reset or restore or whatever it takes to get my wireless working again?
View 1 Replies
View Related
Jul 17, 2010
I used the "Upgrade" option the last couple of nights to go from 8.04 LTS and was going to go to latest version. Well got the upgrade done last night on 9.10 and now Broadcom gigabit wired connect will not connect to internet. Can ping router just fine. Just cannot get outside of it. Shows as configuredin ifconfig. But the name of it under the network manager is odd. Its ifupdown (eth0) (default) and maps to ent1.
View 1 Replies
View Related
Mar 6, 2011
My wired internet was working fine and dandy under Maverick until today. For no apparent reason, it stopped. The router works fine. All other computers are able to connect. I've tried using different cables with no luck. I have a Biostar A785G3 motherboard with an integrated Realtek RTL8111DL ethernet controller.
My problem sounds very similar to this guy's: [url]. But his strange solution didn't seem to work in my case.
View 9 Replies
View Related
May 5, 2010
I have an Asus EEEpc 1000H netbook with both Ubuntu and WinXp. I just updated from Ubuntu 9.1 to 10.04 and I can no longer connect to my home WiFi!
I have a Netgear router and the network is WPA-PSK password protected. All other devices can perfectly connect. The netbook can under WinXp and could with Ubuntu 9.1. Now, with the 10.04, it keeps asking for the password but never connects. Obviously I triple checked the password and there's no chance of a mistype error.
View 9 Replies
View Related
Oct 13, 2010
When my akoya mini E1210 with UNR10.10 resumes after sleep my wifi searches forever and then cuts out. When I do iwconfig the card seems normal for about a minute and then I do iwconfig again it gives gives no id. Reboot and bang, everything perfect. Did make new driver from latest ralink driver, as explained by Sven ,but nu change. Also blacklisted the rt2800 and rt2x00.
Seems that after sleep the wifi card driver is not loaded. Worked like a charm in 9.10 and in 10.4 (upgrade from 9.10). After update to 10.10, it went wrong.
extra: when I do sudo ifconfig ra0 up I get the message "SIOCSIFFLAGS: Operation not permitted" Also, after hibernation, no luck...
in dmesg found that the mailbox keeps MCU active, and rt2860 could not be initialised.:
Quote:
maarten-laptop kernel: [ 1902.168454] ERROR!!! NICInitializeAdapter failed, Status[=0x00000001]
maarten-laptop kernel: [ 1902.168788] ERROR!!! H2M_MAILBOX still hold by MCU. command fail
maarten-laptop kernel: [ 1902.174003] !!! rt28xx Initialized fail !!!
When Evolution Mail is not used, everything is ok. I know this message is not related to mail, but it helps for a while. After longer period of sleep, same problem again. Firmware problem?
View 7 Replies
View Related
Jun 10, 2010
I recently installed Ubuntu x64 on my dell studio 1535 using the windows installer (wubi).
All seems to be working fine apart from the built in wireless card, the proprietary driver (found in hardware drivers) installs and activates successfully and works perfectly. Until I shut down or restart the system. On the next boot the wireless card is 'disabled' and no longer works.
The card I have is a Broadcom Corporation BCM4312 802.11b/g
I am going to try a proper install on a second partition rather than using wubi later on but wondered if this was a commonly occuring problem?
The wireless card works as soon as the driver installs, however I am shown a "restart to activate driver" message and after restarting it's dead.
View 5 Replies
View Related
Feb 2, 2010
I had a problem with using ndiswrapper to install Windows driver on Netgear WN511TA wireless adapter card. Problem solved by replacing Netgear WN511TA with Airlink101 AWLC6080 PCMCIA wireless adapter to work in my triple-boot XP Pro/Ubuntu Karmic/openSUSE 11.2 Toshiba laptop and using the latest Linux driver version 2.3.0.0 dated January 29, 2010 from Ralinktech site. I followed driver instruction in a Ubuntuforums tutorial (Howto: Ralink RT2860(m) PCI(e) RT2860...on Intrepid).
I am wondering if I can use the same Linux driver (RT2860sta) for openSUSE 11.2 on my triple-boot XP Pro/Karmic/openSUSE laptop, ie. copying over instead of building and compiling driver from source again, because I don't quite understand the build instruction given in the README file of Ralink's Linux driver file. Specifically, I don't know how to "define the GCC and LD (?) of the target machine, and define the compiler flags CFLAGS(?), modify your need (?)", etc. I already have gcc, cpp and make installed on the Ubuntu and openSUSE parts of my machine. I did try ndiswrapper in openSUSE but it doesn't work for the Windows version of the latest Ralink driver (error: invalid driver rt2860.inf).
View 9 Replies
View Related
Jun 24, 2011
I use Ubuntu 11.04 on a PC clone desktop.With ethernet cable connects automatically, despite compiling wlan0 not connected. Do not know what I installed Ubuntu 10.04 and 11.04 over 30 times and still the same. Try to manually connect to the network connection did not work either hidden and also deal with ipv4 address assigned and neither worked.
1 ) Machine Brand and Model (PC/Laptop):
desktop pc, clon.
2)lspci
00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
00:02.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Graphics Port 0)[code].....
Try setting manually to no avail not know if I did well. Ralink also downloaded from the rt2860sta and then compiled and did not work. Now I went to install Ubuntu 11.04 and change nothing but that which is above is what I have right now in the machine.
View 9 Replies
View Related
May 8, 2011
I just updated my work laptop to Natty: perfect. My home server: perfect. My oldish home laptop: no more wireless. [I use wicd instead of Knetwork (or whatever it's called) because I want a permanent connection no matter the user]
I have a D-Link DWA-645. I get the whole stage: connecting, authenticating, etc... and bad password at the end. The password is correct (hasn't changed during upgrade). I also tried disabling WPA and it still won't connect. That's wlan2.
I also tried with an older PCMCIA card that _used_ to work on ubuntu 9, but stopped on version 10: a D-LinkDWL-G650. It doesn't even show up as wlan0 as it used to. I also tried with a USB-wifi DWL-G122 which has always worked on every version of Ubuntu [I don't normally use it because it's not practical on a laptop]. I see it as wlan1, but same thing: won't connect. Note that like with wlan2 I can scan for networks and see several around. For instance:
Code:
$ iwconfig
IEEE 802.11bg
ESSID: off/any
Mode: managed
Access point: not associated
Tx power: 20 dBm
Retry long limit: 7
[Code]...
[Edit]
Some more info: the access point works fine, I can connect with another device. The driver in use by Ubuntu is ath9k. Using KnetworkManager instead of wicd doesn't change anything.
View 2 Replies
View Related
May 2, 2011
After being prompted by UpdateManager, I upgraded my Compaq Presario CQ71 from 10.10 to 11.04 yesterday. Most things seem fine, except that my wifi is disabled (it was working fine in 10.10).
Here are some details:
Code:
Code:
View 1 Replies
View Related
May 5, 2011
I have two laptops, both with broadcom drivers and in both it's working pretty well with my university network but I can't find my home network on the list (I can see my neighbours network). It was working perfectly before the upgrade, and of course, I can connect on windows to my home network.
View 2 Replies
View Related
Jun 19, 2011
Our Acer 5820T handles Natty nicely in all respects except for the wifi not working. It was fine under 10.10. It uses the Atheros ath9k driver ... details:
Code:
rick@pond:~$ uname -a
Linux pond 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:24 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux
[Code]...
View 9 Replies
View Related
Apr 30, 2011
I have just upgrade to natty from maverick and my usb wifi dongle doesn't want to work. The usb wifi adapter i use is a Thonsom Speedtouch 121g. When using ubuntu 10.10 it work's fine after installing the package linux-firmware-nonfree, but after upgrading to natty it has stop working (the linux-firmware-nonfree package is installed [don't know if is the same version or an upgraded one]).
The network manager doesn't display available wifi nets. The output for lsusb is:
Bus 001 Device 004: ID 06b9:0121 Alcatel Telecom SpeedTouch 121g Wireless Dongle
View 9 Replies
View Related
Jul 2, 2011
I've been snooping around on the forums for a couple of hours now looking for a straightforward guide to installing custom wireless drivers. I have a new Airlink101 AWLH6075 wireless card (and no ethernet connectivity.) The Linux drivers are the RT2860 Ralink drivers in a .tar, which I have on a different computer.
So -- I'm on Server (command-line only), 64-bit, no working internet. Btw, the wifi card works fine on my alternate boot of Windows. wlan0 (wlan1?) is not detected during installation.
So, I know I need to:
1. mount the usb drive I'm storing the file(s) on
2. put those files in my local Linux directory
3. somehow install them
4. (disable my old ethernet connection?)
5. enable my new wlan0 and set up dhcp and the WEP login.
[Code]...
I would greatly appreciate any help I can get with any of these things. I don't even know how to mount a USB stick in command-line... but obviously the internet connectivity (and thus driver installation) is the major issue here and I can find out most of the other stuff on my own.
View 9 Replies
View Related
May 14, 2010
I am using Ubuntu 10.04. The Tata Photon+ card Huwai EC1260 was working flawlessly. However, I recently did a firmware upgrade on the card that was provided by Tata Indicom for it to work on Windows 7.
After that, the card is no longer detected as a mobile modem in Ubuntu. If I try to add a new connection, all options are disabled (whereas earlier Tata Photon card would appear automatically).
The product ID has changed. What change can I make to Ubuntu to enable it to detect the card again.
View 6 Replies
View Related
Feb 1, 2011
I went out and purchased a Sabrent PCI wireless 802.11n card with the RT2860 chipset because it was on the ubunutu compatibility list and has linux driver available from the manufacturer. I was impressed that the card worked in wireless G mode out of the box, which is a great start....
However, I can't find any wireless N networks. Dual booting I can find/use my N network, but in ubuntu I can only find my G network. This is somewhat frustrating because I bought this card and a new (read: expensive) Linksys E3000 router specifically to run a nice new N network...
I have downloaded, made, and installed (reboot) the latest driver from the manufacturer, but it still won't find any N networks. I found a few posts by searching here and google that alluded to changing this line: "HT_OpMode=1" (from 0 to 1) in the config file RT2860STA.dat located in /etc/Wireless/RT2860STA/ and a reboot. It didn't work for me.
Frankly all this rebooting is starting to **** me off ... I have spent most of last night trying to setup my 180$ wireless network and its still no better than the freebie DDWRT54g based wifi it replaced. I am frustrated, perhaps someone wiser in the ways of ubuntu and wireless N can shed some light on the situation....
I forgot to mention I am on Karmic Kola, amd64 with the standard gnome.
View 3 Replies
View Related
Feb 5, 2011
Just built a new computer and I think I somehow need to activate my wireless card to get it working.The hardware seems to show up. I get "Wireless Networks" in my network manager but it is grayed out and says disconnected. I think it is an easy fix I just cannot find it.
[Code]...
View 4 Replies
View Related
May 6, 2011
Before upgrading to Natty I used to have a Banshee icon in my panel when the application was open - I could close the program but it would just minimize to the panel. Now when I open Banshee there is no icon in the panel. I checked the preferences menu to see if I could change this setting, but didn't see anything there.
View 2 Replies
View Related
