Ubuntu Networking :: No Wifi After Upgrade To Natty Speedtouch 121g
Apr 30, 2011
I have just upgrade to natty from maverick and my usb wifi dongle doesn't want to work. The usb wifi adapter i use is a Thonsom Speedtouch 121g. When using ubuntu 10.10 it work's fine after installing the package linux-firmware-nonfree, but after upgrading to natty it has stop working (the linux-firmware-nonfree package is installed [don't know if is the same version or an upgraded one]).
The network manager doesn't display available wifi nets. The output for lsusb is:
Bus 001 Device 004: ID 06b9:0121 Alcatel Telecom SpeedTouch 121g Wireless Dongle
View 9 Replies
ADVERTISEMENT
May 2, 2011
After being prompted by UpdateManager, I upgraded my Compaq Presario CQ71 from 10.10 to 11.04 yesterday. Most things seem fine, except that my wifi is disabled (it was working fine in 10.10).
Here are some details:
Code:
Code:
View 1 Replies
View Related
Jun 19, 2011
Our Acer 5820T handles Natty nicely in all respects except for the wifi not working. It was fine under 10.10. It uses the Atheros ath9k driver ... details:
Code:
rick@pond:~$ uname -a
Linux pond 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:24 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux
[Code]...
View 9 Replies
View Related
Jun 29, 2010
I recently began using fedora (13) on my acer laptop, and at first the WiFi was fine. However, after a day, it wouldn't connect to my SpeedTouch router through WiFi (though it works fine with a cable), however, it works fine with my Philips Router WiFi.
View 1 Replies
View Related
Apr 29, 2011
Reading recent posts, it seems that 11.04 has seriously screwed wifi.
I have an Advent QRC430 laptop which worked perfectly until I upgraded to Natty. Now wifi is broken. The wifi driver is rt73usb.
When I run lspci in terminal, no wifi card is listed. Running rfkill shows wifi hard blocked, but the switch on laptop makes no difference.
I've installed and run Hardware Lister - this shows wireless interface "has been disabled"
View 1 Replies
View Related
Jul 25, 2011
I have a Broadcom BCM4318 that isn't working with the B43 or the other (I tried installing both and while they supposedly installed successfully, neither shows up in the Additional Drivers tab for me to enable.) I tried using both sets of directions stickied up at the top of this forum. Neither seems to be working for me (no guarantees on whether I did it right) though the B43 is apparently the one I need.Disclaimer: I'm a total newbie to using command line and a new convert from Windows so I'm rusty at navigating and making things work, though things are finally starting to make a little sense after two days of hacking at it.
View 5 Replies
View Related
Jun 7, 2011
I've had recurring problems with Ubuntu wifi on my Thinkpad before. Usually powering down and toggling the physical wifi switch off, then toggling wifi on again after the system has booted would solve the problem. This time that isn't working. Wireless is completely absent from the network-manager applet. Wireless works for me 99% of the time for me, but every few months will "disappear" for some reason. Does anyone have any advice or know a thread they can point me to? I've posted the results for 'lspci -k', iwconfig and 'lshw -C network' bellow:
Code:
$:lspci -k
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
Subsystem: Lenovo Device 2193
Kernel driver in use: agpgart-intel
[code].....
View 7 Replies
View Related
Jun 26, 2011
I was happily running Ubuntu 9 but since I cannot get security updates for it anymore I had to upgrade to 11. Now I'm on Natty, and the "NetworkManager" apparently cannot deal with my latop's wifi card which worked fine for years under ubuntu 9. The laptop is a Dell latitude D610 and the card is an intel ipw2200 minipci. I used to just run /etc/init.d/network restart after I logged in to get the wireless to come up, if it failed by itself, but now I get a message that that's deprecated. Nice.
I'm running WPA. If I don't create a wireless configuration in the network manager, wireless never connects. Ever. If I do create a configuration, the connection comes up for about a minute, and then drops. And then comes up. And then drops. And then comes up. And then drops. It's insane. Also, I get a series of "Auto <ssid>" entries in the NM settings area.I dug around in /var/log, but all of the wpa_supplicant logs are of size 0, except the gzipped backups, which are all size 20. Go gzip. The syslog has some messages in it about 4-way handshake failed, and association taking too long, but since the laptop has no network connection I don't have an easy way to post those here.I just want the wireless to come up, by itself, when I turn on the laptop like it used to. I don't want to have to deal with retyping the (long and complicated) WPA password every time I wake up the machine, nor deal with the "keychain." How do I get there?
View 1 Replies
View Related
May 8, 2011
I just updated my work laptop to Natty: perfect. My home server: perfect. My oldish home laptop: no more wireless. [I use wicd instead of Knetwork (or whatever it's called) because I want a permanent connection no matter the user]
I have a D-Link DWA-645. I get the whole stage: connecting, authenticating, etc... and bad password at the end. The password is correct (hasn't changed during upgrade). I also tried disabling WPA and it still won't connect. That's wlan2.
I also tried with an older PCMCIA card that _used_ to work on ubuntu 9, but stopped on version 10: a D-LinkDWL-G650. It doesn't even show up as wlan0 as it used to. I also tried with a USB-wifi DWL-G122 which has always worked on every version of Ubuntu [I don't normally use it because it's not practical on a laptop]. I see it as wlan1, but same thing: won't connect. Note that like with wlan2 I can scan for networks and see several around. For instance:
Code:
$ iwconfig
IEEE 802.11bg
ESSID: off/any
Mode: managed
Access point: not associated
Tx power: 20 dBm
Retry long limit: 7
[Code]...
[Edit]
Some more info: the access point works fine, I can connect with another device. The driver in use by Ubuntu is ath9k. Using KnetworkManager instead of wicd doesn't change anything.
View 2 Replies
View Related
May 5, 2011
I have two laptops, both with broadcom drivers and in both it's working pretty well with my university network but I can't find my home network on the list (I can see my neighbours network). It was working perfectly before the upgrade, and of course, I can connect on windows to my home network.
View 2 Replies
View Related
Jan 13, 2011
My girlfriend's xp machine has decided to refuse to boot and as a consequence have told her I can install fedora for all her computing needs (facebook and errrrrrrm facebook)
Problem, she's got this strange usb modem, a thomson speedtouch 330 which when plugged into my laptop is listed in lsusb and lsmod which suggest to me the module/driver is built into the kernel, but does not at present work, I'd hate to admit defeat and reinstall xp.
View 10 Replies
View Related
May 16, 2011
I recently upgraded my Zepto laptop to Natty (11.04), and unfortunately the wifi no longer worked. I have a WPA net, and the combination with a Ralink chip seems unfortunate - judging from the number of internet posts.After browsing loads of threads on the 'net I think I have found a solution for 11.04 - it will work out of the box in 11.10 !
1) Add "blacklist rt2800pci" to /etc/modprobe.d/blacklist.conf
I think this makes the wifi stuff work as I can then do "iwlist wlan0 scan" and get reasonable output. But there is no integration with the Network Manager. So I have also done this (again, with inspiration from a few threads):
2) Edit /etc/NetworkManager/NetworkManager.conf - change the "managed=false" under "[ifupdown]" to "managed=true".
You may have to do a "service network-manager restart", restart or similar to get it going.It also seems I can suspend and get a wifi net connection upon wakeup.
View 1 Replies
View Related
Apr 28, 2009
I'm trying to use Speedtouch USB modem.
According to [url].
After a bit of fighting interface works I can ping any domain name or ip address. I can even connect to web server via telnet, for example telnet www.org 80. I can see the response from Web server, but Mozilla says that it is offline, System Update says that no connection.
What can be the problem if manually I can connect but any Gnome GUI program says you are offline?
View 1 Replies
View Related
May 6, 2010
I updated successfully to 10.04 via wireless, then I downloadsynthesizer via wireless. The next day, today that is, can't get wireless to work. It keeps prompting mor the passphrase, I enter everything correctly, all the other computers in the house have no problem.
View 9 Replies
View Related
Aug 22, 2010
I ran the upgrade from 9 to 10.04. So far I have everything but wifi. There is no wifi access even through a menu bar icon. Any others with this problem who've found a solution?
View 2 Replies
View Related
Sep 10, 2010
I have a good connection with 9.04 but when I upgrade it to 10.4 the network keeps looking for wiFI. I have a Linksys USB adapter 2.4HZ.
View 8 Replies
View Related
Oct 13, 2010
I'm facing a strange problem after upgrading my Ubuntu to 10.10. After I start up the system, the wifi is not getting connected by default (which was getting connected automatically in the earlier version). So I right click on network manager and click on 'Enable Wireless' option and it gets connected. So far so good. Now I close the laptop lid - it goes to sleep mode and after it wakes up, the wifi never gets connected. When I right click on the network manager icon, the 'Enable Wireless' option is disabled! I have to reboot my machine to get connected!
Here are the details:
Code:
Laptop : Lenovo U330
lshw -C network output:
*-network
description: Wireless interface
product: PRO/Wireless 5100 AGN [Shiloh] Network Connection
vendor: Intel Corporation
physical id: 0
bus info: pci@0000:03:00.0
logical name: wlan0
version: 00
serial: 00:21:5d:0b:08:d6
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=iwlagn driverversion=2.6.35-22-generic firmware=8.24.2.12 ip=192.168.1.3 latency=0 multicast=yes wireless=IEEE 802.11abg
resources: irq:46 memory:e4500000-e4501fff
View 9 Replies
View Related
Jan 12, 2011
I would like to re-raise this topic that I have seen on other discussion boards but seems to be going no where.I have been using Ubuntu for many years now having switched from other distributions. All my machines ran some version of Ubuntu, until just recently. I upgraded my personal HP TX2500 from 9.04 to 10.04. No problems. After 10.10 had been out for a while I upgraded again. The wireless would drop when busy/(signal slightly weakened) etc. It would not function again unless the wifi module was reloaded.
Then I installed 10.10 on my HP NC6400 the same thing occured. I installed Ubuntu 10.04 instead. It seemed no better. After some Googling, it seemed I was not alone. I tried all the suggestions I could find and none of them worked. One suggestion was to install Fedora 14. This works perfectly on the nc6400. The HP TX2500 has been reinstalled back with 10.04 where the wireless seems ok and I assume I am stuck there for a while.
Now my question is why would the networking behave this way for Ubuntu 10.10 (10.04 as well on the NC6400) but wireless on Fedora 14 is perfect (I mean really good! Better than either Ubuntu 10.04 or 10.10 on any of my laptops) on the NC6400. I am hoping that we can find a way to fix this, otherwise I will likely have to drop Ubuntu completely because I do not have an upgrade path for laptops. There must be many other users in the same position who are not discussing it and just rebooting each time this occurs. This must give a negative perception of otherwise great software.
Systems running Linux
Dell D610
HP TX2500
HP NC6400
IBM T20
[code]...
View 7 Replies
View Related
May 27, 2011
after upgrading to 11.04, I can't use the fn-f2 combination anymore to activate the wifi card. I'm using a Dell latitude laptop. Wifi is functioning normally when it's on and I can even turn it off with the hotkeys. When I try to turn it back on, the light goes on for a second and than dims again. I than have to reboot into Windows to get it back on, which is kind of annoying.
View 2 Replies
View Related
Dec 21, 2010
i've got an IBM thinkpad 1858. fedora 11 & 12 (KDE spin) were always running without any major problems. today, i upgraded the system from f12 to f14 using preupgrade (and a wired internet connection). the upgrade process went smoothly.
but now i don't have a wifi connection anymore - there is no icon shown in the system tray and the led does not blink. the network configuration tool shows eth1 to be inactive and the button to activate it is grey.
lspci -v shows:
Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
Subsystem: Intel Corporation IBM ThinkPad R50e
Flags: bus master, medium devsel, latency 64, IRQ 21
Memory at 90306000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ipw2200
Kernel modules: ipw2200
View 5 Replies
View Related
Jan 1, 2011
since the upgrade i see all avaible wifi networks as they have 100% signal, both in NetworkManager and Wicd.in iwconfig and iwlist the signal levels change, but the link quality remains the same: 70/70 (see below). What could be worng? What can i do?
comp. model:
msi wind u100 netbook, ubuntu 10.10, kernel: 2.6.35-24-generic i686
lspci:
Code:
02:00.0 Network controller: RaLink RT2860
Subsystem: Micro-Star International Co., Ltd. Device 6890
Physical Slot: 0-1
Flags: bus master, fast devsel, latency 0, IRQ 17
[code]....
View 3 Replies
View Related
May 9, 2011
I'm on a Dell Inspiron 6400 which had been running Ubuntu 10.10 (32 bit) perfectly.Today I upgraded it to Natty and the wifi now refuses to work. Details: While no Additional Drivers were needed on 10.10, upon installing Natty it prompted me to install "Broadcom STA proprietary wireless driver". Now when it's active I don't even have the option 'Enable Wireless' (only Enable Networking). If I disable STA the Enable Wireless option comes back, yet I can't actually search for wifi networks or connect to my saved one. The keyboard key to enable/disable wireless also does nothing.
I can take this laptop to somewhere with an ethernet connection for an afternoon if need be, but am currently stumped as to what to do. Obviously I know this machine can handle Wifi under Ubuntu - it's definitely a Natty problem.
View 6 Replies
View Related
Jun 18, 2011
i have a dell 1501 that has been upgraded from 10.10 to 11.04. everything was working okay. and then the user ran an upgrade recently. subsequently the wifi has mysteriously stopped working. it connects okay if one plugs it directly into the router but the wifi seems to have just stopped working.my mini 9 connects fine to the netgear wifi router using wireless.when i run the system tests for networking i get the errors..."root could not find def gateway info /proc""root could not find default gateway by running route"here is the output from some diagnostic commands.NOTE:this is similar to a post titled "wi-fi dead?" but the output is not quite the same...
lauren@lauren-Inspiron-1501:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[code]....
View 3 Replies
View Related
May 29, 2011
Wifi network operated perfectly with f13. Upgrading f13 to f14 did not show any problems except for networking. It seems that the wlan0-link is not ready. Consequently no network information about adresses can be obtained. Tried with network tools to activate wlan0. No reaction Tried to deactivate Networkmanager and bring network up with
service NetworkManager stop
ifconfig -a
Then
ifconfig wlan0 up
dhclient wlan0
No reaction on network. The NetworkManager icon disappears which is understandable.
View 14 Replies
View Related
Dec 4, 2010
i'd like to extend that ma intel wifi link 5100 is not detected no more after perform upgrade package( upgrade the kernel too ). when im using command 'lshw -C network' , there is appear to be detected, but not on command 'iwconfig' or even 'ifconfig' it just show nothin. also network-manager no longer show that ma wireless is work properly anymore.
the old kernel : 2.6.25-22 ( my wireless detected and usable )
the new kernel : 2.6.25-23 ( my wireless detected and unusable )
View 4 Replies
View Related
May 31, 2011
My Intel Corporation WiFi Link 1000 Series wireless card stopped working yesterday after I did an update via Update Manager.After the upgrade, wireless is disabled and the option to enable it in Network Manager is grayed out. I thought that it might be the new kernel, but changing back to the old kernel I still have the problem.
View 8 Replies
View Related
May 12, 2011
Just upgraded to Natty on both my desktop and netbook. Desktop upgrade was a breeze, and I'm liking the changes.Netbook isn't having such a good time however.First login after upgrade (using default gnome settings) played the login sound and froze. No mouse movement/keyboard response. I tried again with Ubuntu Classic - nothing. Finally Ubuntu Classic No Effects did correctly boot/login. I allowed it to perform a proper shutdown (was doing a power flip beforehand), and it was able to boot into normal Ubuntu Unity.
I enabled the wifi module using the laptop's keyboard shortcut, and Ubuntu searched for nearby networks. After finding my prefered network, it started to connect and threw the system into a command console abyss and froze. Tried again on the Ubuntu Class no effects, and it freezes on connecting to a wifi network. If the laptop crashes and I have to perform a power cycle, I can't boot into normal Ubuntu mode. I have to go back into Classic no effects.
Details
OS: Ubuntu 11.04
Previous OS: 10.04 Ubuntu Desktop Edition
Laptop: Asus Eee 1001P
Wifi Network: WPA2/AES/PSK
View 3 Replies
View Related
Dec 4, 2010
Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
View 6 Replies
View Related
Apr 30, 2011
I'm on Natty since yesterday but I started the day before. My first impression was great. I now had an option top upgrade from 10.10 and not loose my data! So I did. It all went fine until the point where The Upgrade tries to restore my applications. It failed and returned the message:
unbalanced group option, expect badness.
And that was it! And I would have been waiting a very long time if I wasn't looking the details of what's going on because from here and after a 3rd try, I went to sleep online to find out I was still expecting badness the next day. I did a hard reboot and tried login in. I reached the login screen with success but could never login. I was using the encryption options which it seems comes after the restoration of application.
The symptoms are those of a wrong password. I finally did a clean install and restored my data from my backups (wouldn't try something new without a backup). Otherwise, I like Unity. I see a few things that needs polishing here and there but I don't mind using it. I think that voices from people liking it need to be heard as well because they usually don't have a reason to complain and it then looks like every body think Unity is not good.
View 2 Replies
View Related
Apr 5, 2011
When i upgraded the whole process went all right then when I logged in, i mostly saw black and no unity bar could barley get around.
View 2 Replies
View Related
