Ubuntu Networking :: RT2860sta No Wifi After Resume From Sleep?
Oct 13, 2010
When my akoya mini E1210 with UNR10.10 resumes after sleep my wifi searches forever and then cuts out. When I do iwconfig the card seems normal for about a minute and then I do iwconfig again it gives gives no id. Reboot and bang, everything perfect. Did make new driver from latest ralink driver, as explained by Sven ,but nu change. Also blacklisted the rt2800 and rt2x00.
Seems that after sleep the wifi card driver is not loaded. Worked like a charm in 9.10 and in 10.4 (upgrade from 9.10). After update to 10.10, it went wrong.
extra: when I do sudo ifconfig ra0 up I get the message "SIOCSIFFLAGS: Operation not permitted" Also, after hibernation, no luck...
in dmesg found that the mailbox keeps MCU active, and rt2860 could not be initialised.:
Quote:
maarten-laptop kernel: [ 1902.168454] ERROR!!! NICInitializeAdapter failed, Status[=0x00000001]
maarten-laptop kernel: [ 1902.168788] ERROR!!! H2M_MAILBOX still hold by MCU. command fail
maarten-laptop kernel: [ 1902.174003] !!! rt28xx Initialized fail !!!
When Evolution Mail is not used, everything is ok. I know this message is not related to mail, but it helps for a while. After longer period of sleep, same problem again. Firmware problem?
I'm sure this doesn't need a new thread but after searching for a bit I didn't find much about this. The problem is this;My system sleeps quite well, I can resume from sleep and get back to the desktop. However. the one thing that doesn't resume is > networking.I can disable> re-enable networking from the NM-applet and it tries again to connect but won't.I can sudo /etc/init.d/ networking restart, which essentially is the same as above. No connectionI've run ifconfig, and the connection is there but no address. Has this bug not been solved? Is it just a driver issue with my particular network card?It's the realtek 8201, part of the VT8237 chipset.Does anyone know what to do about this? I've been avoiding sleep mode on this computer for a very long time because of this bug.
After I resume from hibernate with my cpu frequency manually set to the highest settings (2ghz) the network manager shows not wifi APs. "wlan0" shows under both ifconfig and iwconfig but "iwlist wlan0 scan" says no results. "sudo iwlist wlan0 scan" also says no results. I've tried rmmod then modprobe with no luck. Rebooting is the only way I can get WiFi working.
I can get wifi working again by: - rebooting - changing the cpu scaling to a lower setting then hibernate/resume - changing the cpu scaling to a lower setting then 'sudo rmmod ath9k; sudo modprobe ath9k;'
I am using Ubuntu 10.04 with Atheros ar5008 (AR5BXB72) using ath9k drives Code: $ lspci |grep Atheros 0e:00.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) Code: $ uname -r 2.6.32-24-generic
I'm having trouble getting conky to start automatically after resume from sleep. I've tried putting a copy of my conky startup script into /etc/pm/sleep.d but nothing happened.
I just bought a Logitech V470 bluetooth mouse. It's no problem to let it work under Koala 9.10 (gnome), but after shutdown/standby/sleep, it doesn't work anymore. With my USB mouse, I have to click the bluetooth icon and select 'switch off bluetooth'. After that, I click 'switch on bluetooth' and bluetooth works again. I thought switching on and off bluetooth with the applet is the same as 'sudo /etc/init.d/bluetooth start/stop', but it isn't! The previous command greyes out/in the bluetooth icon, but it doesn't resume my bluetooth. If 'sudo /etc/init.d/bluetooth restart' would work, I would be able to add this line into /etc/pm/sleep.d, so it's automatically loaded on resume.
I have upgraded from Ubuntu 9.x to 10.04 LTS after the upgrade, my netbook goes to sleep in a short period of time and makes me login every time i resume. This is very annoying as i have to wait for login and sometimes my wifi connection drops. I just quickly want to check my messages. The delay is annoying and has me using a windows (argh) laptop instead. i miss my ubuntu netbook.
i have tried adjusting power management setting to never go to sleep and adjusted some other power management module from the command line, but with no luck. is there a way to reset the sleep pref's or any way to fix this.
Just recently I notice this behavior. When the machine sleeps either on timeout or after closing the lid, it doesn't come back on opening or hitting esc etc..
The machine seems to come back to life, but the screen stays black. I even tried Ctl-Alt-F1 with no response.
uname -a yields Linux xxxxxxxxx 3.2.0-4-amd64 #1 SMP Debian 3.2.65-1+deb7u1 x86_64 GNU/Linux
and lsmod for video yieldsvideo 17683 2 i915,nouveau
Running FC13 on Dell E6410. Everything was great until I ran the latest update about a week back. I started to see (or actually not see) that after resume from sleep the mouse cursor will disappear. It is there, just not work showing. If i click on left click on the desktop I get the menu, I can also "see" going over windows from time to time as I move it. I'm currently running 2.6.33.6-147.fc13.i686.PAE I think previously it was /vmlinuz-2.6.33.5-124.fc13.i686.PAE Nvidia driver is 195.36.31
I recently upgraded my Zepto laptop to Natty (11.04), and unfortunately the wifi no longer worked. I have a WPA net, and the combination with a Ralink chip seems unfortunate - judging from the number of internet posts.After browsing loads of threads on the 'net I think I have found a solution for 11.04 - it will work out of the box in 11.10 !
1) Add "blacklist rt2800pci" to /etc/modprobe.d/blacklist.conf
I think this makes the wifi stuff work as I can then do "iwlist wlan0 scan" and get reasonable output. But there is no integration with the Network Manager. So I have also done this (again, with inspiration from a few threads):
2) Edit /etc/NetworkManager/NetworkManager.conf - change the "managed=false" under "[ifupdown]" to "managed=true".
You may have to do a "service network-manager restart", restart or similar to get it going.It also seems I can suspend and get a wifi net connection upon wakeup.
I use Ubuntu 11.04 on a PC clone desktop.With ethernet cable connects automatically, despite compiling wlan0 not connected. Do not know what I installed Ubuntu 10.04 and 11.04 over 30 times and still the same. Try to manually connect to the network connection did not work either hidden and also deal with ipv4 address assigned and neither worked.
1 ) Machine Brand and Model (PC/Laptop): desktop pc, clon.
2)lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:02.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Graphics Port 0)[code].....
Try setting manually to no avail not know if I did well. Ralink also downloaded from the rt2860sta and then compiled and did not work. Now I went to install Ubuntu 11.04 and change nothing but that which is above is what I have right now in the machine.
I have just joined the Debian community, for the past 2 years I have been using Linux Mint (ubuntu), I am now using Linux Mint Debian 64. I have a Lenovo A700 ideacentre with a Broadcom 4313 WiFi card. I manage to get the card working, now I have a new problem. If I suspend the machine the WiFi will not connect on resume. Is there a simple command I can use to getting the connection restarted, or better yet a work around so it will restart on its own?
I'm running Debian testing. I am running the iwlwifi driver and I have an Intel Centrino Wireless-N 1000 card. I have a fresh install of iwlwifi and network-manager. After sleep or after being shutdown, network manager cannot find my network's SSID. I have to wait ~5 minutes for it list my SSID. I dual boot this laptop with Windows 7, and on Windows, I connect to the internet instantly after boot. I did not have this issue before, the only thing I have changed was installing blueman and the necessary components. After I installed and uninstalled these bluetooth components, I have been getting these problems. Here are some outputs:
iwconfig: Code: Select alleth0Â Â Â no wireless extensions.
wlan0   IEEE 802.11bgn ESSID:"Dotcom"      Mode:Managed Frequency:2.462 GHz Access Point: 14:AB:F0:3D:DC:20       Bit Rate=81 Mb/s  Tx-Power=14 dBm       Retry short limit:7  RTS thr:off  Fragment thr:off      Encryption key:off
Wonderful Debian 6 in live mode! Using it with my EeePc 901 with ralink rt2860sta wireless Doing lsmod, rt2860sta is on 0 (it means, don´t charged) How can I use my wireless rt2860sta in live mode?
I just switched over to openSUSE about a week ago from Ubuntu and I just purchased an Asus N13 PCI-E wireless network adapter which uses an RALink 2860 chipset. I plugged it in and openSUSE was able to detect it and everything but when I went to go configure it using YaST, it wouldn't be able to scan for networks.
So, I reinstalled my old adapter, downloaded the latest source from RALink and compiled the drivers. When I tried to use insmod on the new .ko that was compiled, I got the "Could not allocate memory" error.
If you need dmsg logs or anything else, I can reinstall the card and get those.
For a long time, on my netbook Asus EEE pc1000 working fine with my wireless (connecting WEP, WPA). Running with kernel 2.6.29 + rta2860sta v2.2 (package downloaded from the software repository , a user repository)
After somes updates (kernel mainly), all stop working. So I recompile the module v2.2 but don't work. I download from the ralink site the last version , recompile and installed , and appear work fine, but I don't know why the opensuse like to be very annoying and the knetworkmanager don't recognize the device. So , again I download a package from a user repository with the version 2.3 , what appear starts working again. Knetworkmanager recognize the device, but isn't cappable to connect in a WEP network. With WPA works fine.
If I disable the device in knetworkmanager and try configure manually , sometimes work. Probably have some sequence of command what I don't figure out what is. To configure WEP network before this problems I always use only the "iwconfig" command. But I try with "iwconfig" and "iwpriv" and don't work. So , afiter trying a lot of sequence, now I got connected to WEP network, but is very weird how they show this connection,
My laptop has an internal wireless device and a button to turn it on/off, but since it has bad reception I use an external USB wireless adapter.The problem is that if I turn the internal wireless device off using the button, it also turns the USB wireless adapter off.Is there anyway to use the killswitch (the button) only for the internal wireless device?This only started to happen in Ubuntu 10.04.
I have only had a few weeks worth of experience with linux, so I'm probably considered a newbie at this but I felt like giving it a shot. I just configured my new Toshiba Satellite A505-S6969 to jaunty. Most of the transition is going well but I'm stuck with a few issues, one of which is getting my wifi to work. Right now I'm working off of an ethernet cable.spci returns
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port
Installed ubuntu 9.10 dual boot with win7 yesterday. Everything working but Wifi. Wifi works fine with Win7. No Wifi in Ubuntu. Very confused. I have info from the wifi trouble ticket post.There does not seem to be a driver for this card anywhere.
lawrence@lawrence-laptop:~$ lspci 00:00.0 Host bridge: Intel Corporation X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13)
get WIFI working on my Dell D600 with Ubuntu 11.04 freshly installed. I some limited sucched following the this post t=1621331 this got the card working but it was very very slow over 70% packet loss to the WIFIrouter. 1. Machine details Dell Latitude D6002 Wireless Broadband and Chip setlspci -nn | grep Broadcom - 02:03.0 Network controller [0280]: Broadcom Corporation BCM4309 802.11a/b/g [14e4:4324] (rev 02)3. Check interfaces
eth0 Link encap:Ethernet HWaddr 00:0b:db:e0:1c:5b UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0
I have a pc which has 2 network cards, 1 wifi and 1 ethernet card.
I'm using wifi card to connect to wifi network (internet) and i'm planing to share this wifi/internet connection via ethernet to wireless router (siemens sx763) so i can have internet on my other devices, e.g. mobile phone, laptop.
After seeing those 4G phone commercials with that newfangled mobile hotspot tech, I have to admit I was eager to trade in my crappy 2 year old CDMA phone for one. That is, until I saw the price tag. 30$ a month for hotspot? No way, so what I did was activate the tethering feature buried deep within the primitive OS accessible only with a plethora of codes and hackery. So long story short: I can now network on the go because Ubuntu sees my device as a "mobile broadband device". Unfortunately, my ipod lacks a USB port for tethering so I use my freed up wireless card to make an AD-HOC network for my ipod to connect through my makeshift modem. Now, my issue is that the modem isn't really that mobile any more because I have to have my laptop OPEN to keep my networks on ,otherwise I close my laptop and no more Adhoc or mobile broadband! So, my question is if I can close my laptop but still keep it connected to the mobile broadband and broadcasting the adhoc network.
I am running (K)Ubuntu Lucid 10.04 64bit on a Dell Latitude E6400, WiFi Card Intel 5100. Never had any problems with networking. Up to about 2 weeks ago. I do realize there have been quite a few posts with this network adaptor, but non really described the problem I have here.
What happens is that suddenly the WiFi LED on the computer stops blinking, the WiFi connection gets disrupted, and the device is not recognized anymore when checking ifconfig. Only cold restarting the machine helps then... it will work for a while (between 1 and 20 minutes) and then crash again.
On Windows 7 the card works perfectly fine. With Ubuntu 11.04 in Live CD mode I have the same effects (connection crashes after a while). Also tried booting an older kernel, no success.
My exact hardware:
Code:
I notived the following problems in /var/log/kern.log
I have 2 connections, wlan and wired, and I'd want to have a few websites (in my browser) to connect through the wireless connection while other go through the wired rj45 connection. s it possible? (without unplugging the rj45 cable...)
the only error message I can find comes from "dmesg|tail"all it shows is "no IPv6 router"any body know what is going on here or where where to look for more clues the next time I get around public wifi Oh the windoze washers and apple polishers don't seem to have any problems at all
I've read many threads here on wireless problems in 10.04. I've got it updated as of this morning.
Symptom: wireless works perfectly - doesn't drop out and starts right up at boot. But if computer (Dell Latitude D505) goes to sleep, wireless won't resume. Network Manager shows wireless networking greyed out after waking.
I have an old PowerBook G4 that I would like to use as a 'dummy' computer for learning wireless penetration (WEP/WPA attacks) more effectively. I had been using a wireless router, but I gave it away I can use Mac OS X to share an ethernet connection over wifi, but this is _very_ un-configurable. You get two options only, WEP and a key-length. So, I would like to install someway to make this wireless connection more configurable.
I'm setting up an HTPC (Zotac IONITX-F in a Silverstone ML02-MXR case with remote) running XBMC on top of a minimal karmic install. So far I've managed to get everything running including the tricky stuff: wireless, lcdpro and lirc. I did have the same samba/dhcp conflict described in this thread, so I opted for a static IP solution instead of the usual dhcp connection with the router (D-link DIR-615) reserving an IP for the MAC-address. This is my /etc/network/interfaces file:
Code: auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet dhcp
I'm currently using putty on my laptop to control my headless server (both Ubuntu 8.04.) I'm running an rsync job that ran all night long and still going all day today so far. I need to restart my laptop, but if I do, I'll break the SSH connection. If I SSH back in, I won't see the same thing (rsync is showing me each file it's copying) that I'm seeing now. (At least I think that's true. Please correct me if I'm wrong.)
So I guess my questions are..Is there some way to restore my SSH session when reconnecting? (So I can resume seeing which file is being copied and - more importantly - when the rsync job (finally) finishes?If not, how else can I know when the rsync job finishes?
