Using sudo iwlist scan, i will get a list of surrounding AP(s) around my laptop, is there a way to interpret the sudo iwlist scan results so that we can know what encryption type is the wireless network using?
View 3 Replieswlan0 Authentication capabilities :
WPA
WPA2
CIPHER-TKIP
CIPHER-CCMP
Those are my authentication capabilities, obviously. I am using a WEP encryption for my wireless router and according to this, it will not allow me to connect. Is there anyway to allow that? The wireless card works just fine in Windows, even on the same network encryption type. Using a Intel Wireless/Pro 4965 ag. Note* this is my mother's router and whatnot. She won't change it the encryption type.
Using Linksys 54G wireless card and connected with no encryption but will not when encryption is used?
View 1 Replies View RelatedI am building an active directory and using BIND9 as my DNS. To allow for secure dynamic updates from the domain, I am enabling GSS-TSIG as detailed here and here. Unfortunately, some of the commands and configurations used here seem to be depreciated, at least in the newer versions that I'm using. My issue is one of keytab encryption. I generated a keytab using ktpass.exe on the Windows Server 2008 domain controller. I have tried DES/MD5, AES128/SHA1 and AES256/SHA1, each have been turned down by ktutil on the kerberos server (FreeBSD). Each time, it outputs the following error: ktutil: AES256/SHA1*: encryption type AES256/SHA1* not supported *Respective to encryption used.
I cannot find a list of suitable encryption schemes that ktutil will accept. The FreeBSD handbook details a means of producing a keytab file, but I'm not sure how to configure the Domain Controller to use the keytab.
enable WPA encryption on my wireless connection? Wireless networks are detected and listed, so the wireless card is functional in the most basic sense, however, when going to connect to any particular network,I am not given the option of entering a WPA passphrase, only WEP, and as my router is set to use WPA, this is a problem.I am trying to get this going on a fresh Karmic install on a Toshiba A15-S157 notebook.Thus far, I have found this: https://bugs.launchpad.net/ubuntu/+s...ux/+bug/315489 which would seem to relate to my problem.I looked in my logs and saw this entry: Jan 10 16:06:35 cody-laptop firmware.sh[863]: Cannot find firmware file 'agere_sta_fw.bin', and have since found that file, and have downloaded it to my desktop. It seems like this may be the solution, but how to exact it, therein lies my (momentary) problem.
View 2 Replies View RelatedI used this password Pass1234 when I search password stored its Nh2yEjhdHIwtY what kind of encryption is used? I thought it was crypt() , but when I create crpypt on my local machine its different.
View 3 Replies View RelatedI recently downloaded and installed CentOS 5.3 DVD media.The media check passed. I proceed to install the operating system sucessfully. After installation, all my hardware is recognized, when compared to CentOS 5.2. Anyway, when I attempt to connect to my wireless network that uses either WEP/WPA/WPA2-- I get an error message that I cannot recall (it basically only came up when I entered the key) However, I can connect to my wireless network when it is unencrypted and no open/shared key is needed.I would like to be able to connect to my wireless network when
FYI: I am using a RealTek RTL8185 Wireless Driver.Also, I use CentOS as a workstation.
on my laptop (dell d620) when I try to connect to wpa networks I get frequent disconnections and very slow speed.
My network card is: 0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
Insted when I use connetion whitout wpa encyption I've no problems...
how to configure iwl3945 to get decent performance on wpa networks ?
there is one problem i encountered here while working with Embedded Artist board or Lpc 2478 uclinux.so my questions.what type of encryption does this uclinux use to encrypt the password?instead of using these 2 username and password,can i put my own password and username?
View 1 Replies View RelatedWhat should my partitions look like? I want to install this to my hard drive, I'm currently running it from DVD.
My drive is sdb
It has 153.3 GB (157065 MB)
I want to know what format type should the partitions be, and how many megs they should be. Which partitions to encrypt, and which I don't need to.
I am running Red Hat Enterprise Server 6.0 I am having issues getting kerberos configured as a client to join a domain. Im getting below error message. "Failed to join domain: failed to connect to AD: KDC has no support for encryption type"
View 9 Replies View RelatedI followed [URL]..to set up my wireless network with WPA2 encryption. It works now and knemo says:Encryption: active. However, "iwconfig wlan0" says Encrytion key: off:
Code:
wlan0 IEEE 802.11abgn ESSID:"blitz"
Mode:Managed Frequency:2.472 GHz Access Point: 00:25:9C:DE:D3:7D
Bit Rate=0 kb/s Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
[Code]...
So is there anything wrong with that "Encryption key: off" statement? I suspect that encryption key only applies to WEP, but not to WPA2 encryption, but I am not sure. So my question is, can I ignore that statement and assume that my encryption is fine?
Besides, where does knemo read the information about encryption from? As I mentioned, knemo detects that the encryption is active. Are there any other commands to make sure that my encryption is safe and well?
I have a question about connections with an ubuntu server. Is there a way to know if the terminal computer (which is connected to my linux server) is using WinSCP to connect (on a Windows platform) or a linux system? It seems they are using the same port (22) and I think the exact same protocol (SSH / SFTP), is there a way to differentiate between the two though? And going farther there, is it possible to limit the connections only to linux terminal computers and reject requests coming from Windows computers?
View 2 Replies View RelatedIs there a way to differentiate between a 32 bit and 64 bit distro from the command line?
I also need to know this for a CentOS 5 box.
I am moderate in linux. Is there any command to know the difference between linux server and desktop Or any system files will give such information.
View 5 Replies View Relatedconstructing a protocol where in it involves sending and receiving different files, so sending data over consists of file name, size of the file and content of the file, so while receiving can i use functions like strchr() to differentiate these fields for sockets? so to allocate memory for file to save i need to have its size.
View 3 Replies View RelatedI'm on an Acer Aspire One.Clean install of 9.10.I was using 9.10 and my wireless was working fine.Then for no reason it would not connect.So I decided to reboot my router and reinstall ubuntu.Still does not work.I have figured out that it seems to be WPA encryption that is at fault.When I turn it off on my Linksys the netbook connects fine, turn it back on and nada.
if i try to use a static address then the laptop seems to connect but I cannot ping the router or get to the internet.If anyone has any ideas I would be grateful, I would rather use WPA than WEP.My iphone connects and this netbook connects with Windows, so I know the linksys is not at fault.
I recently installed Centos in my dell laptop and trying to set up the WEP encryption.
set up the WEP?(BTW the card works , I could scan the networks etc..)
A while back I posted [URL] a question about Ubuntu 9.10 not recognizing my WEP encryption key. The problem that I had is still essentially the same: After upgrading to 9.10 beta, then trying to upgrade using the alternate install disc for the full version (because of the same problem) I ended up having to do a completely new installation. Anyhow the problem still stands: my internet card works and it detects available wireless networks, the only thing is that after entering the key in, it will attempt to connect, then after a min or so, it will ask for the key again, ad infinitum. The upshot is that I can't connect to the internet at all. Right now I'm on Windows 7 RC.
The only thing that has changed is that I tried disabling encryption entirely, and Ubuntu was still not able to connect (I think the connection just timed out after a few minutes). I should add that I have Verizon FiOS, an Actiontec router, and my computer (since it is far away from the router) connects through a Hawking_300N extender. Right now I am using Windows 7 RC (which unfortunately expires in a little over a week), so I can access the internet through Windows, and check for any posts, but I can't immediately provide any command outputs, I'd have to restart, and that would take a few minutes. Further, I have tried both Network Manager and WICD, both of which produced the same results. I have not tried any WPA encryption mainly because the router is shared, and I don't to mess with everyone using the router unnecessarily.
Using a D-Link wireless router, trying to get it through the authentication process with the client through a D-Link DWA-125 USB wireless. When I set encryption to "none" on both ends, the router links up OK, but when I enter matching encryption settings on the router, and then in the driver data file (RT2870STA.dat) on the client side, I can't get it to authenticate. I've tried all possible combinations in the .dat file with no luck. I'm fairly well convinced that there is a bug in the .dat file settings, and that the wireless port setting need to be forced at startup through the /etc/networking/interfces file, or some such procedure, to override the settings in the .dat file.
[Code]..
My laptop able to detect wireless. I try to access it with a correct password. However, it keep prompts me the password is wrong. But I was able to connect the wireless using other PC with the same password. I am pretty sure the something wrong with the WEP encryption of the F15.
View 1 Replies View RelatedThere is a strange thing going out there in my box, I've tested b43-fwcutter on wpa-psk encrypted network, and there was no problem connecting (my card is broadcom 4318), recently I was trying to connect to WEP encrypted network without success. Network connection tested on other laptops (Vista, XP machines)so there is no possibility that the key isn't valid.
View 6 Replies View RelatedI want to share my internet connexion via ad-hoc WiFi. If it's unsecured, it works fine, but when I use WPA encryption, it doesn't work anymore! I can connect from my iPod touch, but no internet. I connect to the internet from my laptop, via eth0 I want to share my internet connection via wlan0 I have no idea what's wrong
View 1 Replies View RelatedIts seems Fedora 11 on eee pc 1000h cannot connect to any wireless type(Open, WPA2, WPA or WEP) of a hidden network(non broadcasting SSID). Though it can connect to visible ones(broadcasting SSID), since my college is on a hidden network this a problem for me. Though I can't really test if its just fedora 11 or rpmfusion drivers for it 1000h model related problem.
View 13 Replies View RelatedI use to have problems getting my wireless card to connect to any network on ubuntu. I discovered that I needed to change my encryption mode from Auto to AES or TKIP on my router. After I did this I was able to connect to my network with full wireless n support. I am using a d-link DIR-615 wireless n router.So far I know this works perfectly on 9.04-10.10 alpha.
View 1 Replies View RelatedI have xbmc, a media center shell that runs on ubuntu. I am trying to set up a laptop to run it and be a full time media center. so far it works great, I installed xbmc live, but the only issue is I have a wep2 protected wireless router and the wifi does not connect automatically.
I have it set up and am using wpa_supplicant once those commands are run the wifi works great.I am a novice in linux in general, and can not seem to get this to work on startup, can anyone point me in the right direction on this? I haven't been able to find the xbmc start up script if one exists, I figured adding those lines to it might work,does this sound like a reasonable approach? if anyone knows where that is and how it is defined to be launched on start-up i would appreciate it(I guess this is getting into the general Linux knowledge but still good info)
Running ubuntu 10.10 here, brand new install/machine.USB wireless based on a realtek chipset. I spent a few days trying ndiswrapper, and now have the native driver up and running. I can see the network(s) but can't connect. If I encrypt the network, i get a bad password error from wicd network manager (All encypt. methods- Weps, WPA etc) If I open my wireless up with no encryption, i receive a "can't obtain IP" error.
View 1 Replies View RelatedWhen I run the following GET commad:
./snmpget -m ALL -M /data/net/naamab/snmp/snmp_mib/ -v 3 -a MD5 -l authPriv -u test1 -A welcome1 -x DES -X privpass 127.0.0.1 NOVELSAT-MODULATOR-MIB::nsModLineCMMode.0 -d
I get the error:
Encryption support not enabled.
snmpget: USM encryption error
I have defined a user (and user, view and access) that should work with encryption:
snmpd.conf:
createUser test1 MD5 welcome1 DES privpass
group debugGroup usm test1
view debugView included .1
access debugGroup "" usm priv exact debugView debugView none
General details:
I am using net-snmp on linux embedded
version 5.5
Configuration (part of it):
./configure --target=mips64-octeon-linux-gnu
--build=mips64-octeon-linux-gnu
--host=i686-pc-linux-gnu
message dump:
Sending 64 bytes to UDP: [127.0.0.1]:161->[0.0.0.0]
0000: 30 3E 02 01 03 30 11 02 04 1D 23 6A FA 02 03 00 0>...0....#j....
0016: FF E3 04 01 04 02 01 03 04 10 30 0E 04 00 02 01 ..........0.....
0032: 00 02 01 00 04 00 04 00 04 00 30 14 04 00 04 00 ..........0.....
0048: A0 0E 02 04 4C 08 7B B5 02 01 00 02 01 00 30 00 ....L.{.......0.
Received 118 bytes from UDP: [127.0.0.1]:161->[0.0.0.0]
0000: 30 74 02 01 03 30 11 02 04 1D 23 6A FA 02 03 00 0t...0....#j....
0016: FF E3 04 01 00 02 01 03 04 24 30 22 04 11 80 00 .........$0"....
0032: 1F 88 80 2D 53 AF 7D 00 00 00 00 00 00 00 08 02 ...-S.}.........
0048: 02 02 CF 02 03 01 11 C5 04 00 04 00 04 00 30 36 ..............06
0064: 04 11 80 00 1F 88 80 2D 53 AF 7D 00 00 00 00 00 .......-S.}.....
0080: 00 00 08 04 00 A8 1F 02 04 4C 08 7B B5 02 01 00 .........L.{....
0096: 02 01 00 30 11 30 0F 06 0A 2B 06 01 06 03 0F 01 ...0.0...+......
0112: 01 04 00 41 01 09 ...A..
I am running Fedora 13 and using Ndiswrapper with my pci wireless card. my router is a netgear wgr614v9 wireless router with wpa2-psk. When I try to connect to my network the only options I see for security are dynamic WEP (802.1x) and WPA &WPA2 Enterprise and for authentication all I see is TLS LEAP Tunneled TLS and Protected EAP (PEAP). I can connect to my network when I drop security on the network but other wise I am stuck. I have been trying to fix it for about a week now by myself to no avail
View 1 Replies View RelatedIn my system around 73gb(pc-desktop) i have,1 primary partition(windows)-25gb, 1-extended partition(remaining gb) 3 logical partitions were there in (under) extended partition in one of the logical partition is d:drive. in my hard disk d: drive is -/dev/sda5
previosly i was fat -file system , (d:drive-/dev/sda5), i remember i changed the d: drive(d:drive-/dev/sda5) file system to ext4file system ,with following command using terminal
After doing(changing the file system)this one ,i couldnt see the d:drive data
By doing that
1q) Did i reformatted the partition? i think the new filesystem(ext4) has no knowledge of the data that was on it when it had a FAT filesystem.
2q) How to do undo operation,i tried to change the filesystem type to fat/ntfs in terminal using command --sudo mkfs -t FAT /dev/sda5.
Result:its showing text message-'mkfs.FAT: No such file or directory'(not in single quote)
I had very imp data in d:drive