Ubuntu Networking :: WiFi Adapter TP LINK WN821N Is Not Working In 10.10
Apr 17, 2011WiFi adapter TP LINK WN821N is not working in 10.10, WN821N is notworking.
[Code]....
WiFi adapter TP LINK WN821N is not working in 10.10, WN821N is notworking.
[Code]....
I got two issues with my wifi usb adapter:
1) it cannot see any networks around
2) i cannot setup it in master mode to use my PC as a router
As far as i can see, the device is recognized and the correct driver (rt73usb) is loaded. I was able to connect to a laptop somehow (the laptop could see other networks and the adapter's PC-to-PC network). I'd like to make it work as a router, i.e. share my internet connection (eth0) via wlan0. Here is what i have:
Code:
Ubuntu 10.04
Linux 2.6.32-22-generic #36-Ubuntu SMP Thu Jun 3 19:31:57 UTC 2010 x86_64 GNU/Linux
TP-Link TL-WN321G wifi usb adapter as seen as
Bus 001 Device 006: ID 148f:2573 Ralink Technology, Corp. RT2501USB Wireless Adapter
$ iwconfig wlan0
wlan0 IEEE 802.11bg ESSID:off/any
[Code]....
my long awaited WUA-1340 D-Link wifi adapter has arrived, and...unfortunately won't work it didn't work "out of the box", so I tried the following (found on the aircrack website)Here's what I did....1. Edit /etc/modprobe.d/blacklist and add blacklist rt73usb as a new line.2. RebootThen,
Code:
wget http://homepages.tu-darmstadt.de/~p_larbig/wlan/rt73-k2wrlz-3.0.3.tar.bz2
tar -xjf rt73-k2wrlz-3.0.3.tar.bz2
[code]....
I have just installed Ubuntu 9.10 on an Acer TravelMate 290E. I've got internet connection through the Ehternet Cable, but when I plug in the D-Link WLAN USB device, although the system recognises it, it is disconnected. How can I connect the WLAN USB device adn get it to work?
View 5 Replies View RelatedIt worked with 10.10, but in 11.04 only partially. It would show up in Bluetooth Manager, and I was able to pair with my phone. But after that it always failed to connect. Tried lots of things before I spent $10 on another nameless Chinese one and that worked fine immediately.
View 1 Replies View Related1. D-Link DWA-643 Xtreme N Express Card Adapter The onboard wireless for my HP tx1000z stopped working a long time ago. This wireless adapter is in my express card slot.
2.
Code:
$ lspci
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
[Code]....
Okay I've got a Netgear N-150 WNA 1100 USB WiFi adapter, it doesn't work in Ubuntu it's not supported. There should be a way to make it work with ndiswrapper. I tried and failed before and due to other non related circumstances I had to reinstall Ubuntu. What are the steps to install ndiswrapper and it's dependency's on a fresh Ubuntu installation that cannot connect to the internet.
View 9 Replies View RelatedI've got a Dell precision with Kubuntu 9.10. Wifi worked fine on that machine for months, but stopped working last week. I don't know what happened, but I recently did an "apt-get dist-upgrade". That might have something to do with it.
When I boot in Windows, wifi works fine.
Code:
tijl@Smaug:~$ sudo lshw -C network
*-network
description: Ethernet interface
product: 82567LM Gigabit Network Connection
[Code]....
my platform Centos 5.3
i did the following
Code:
[root@localhost ~]# lspci | grep Wireless
0c:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
Code:
[root@localhost ~]# lspci | grep Wireless
0c:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
[Code]....
I'm dual booting windows 7 64 bit and Ubuntu 10.1 64 bit on my Dell Inspiron 11z with an embedded WiMAX/WiFi Link 6050 series wireless card made from Intel. I only use it for wifi, not 3g or wimax. I installed the latest driver from intellinuxwireless.org, iwlwifi-6050-ucode-41.28.5.1, but it still doesn't seem to work. I ran these terminal commands from another thread:
cd Desktop/wlwifi-6050-ucode-9.201.4.1
sudo cp iwlwifi-6050-4.ucode /lib/firmware
sudo chmod 644 /lib/firmware/iwlwifi*
[code]....
After running "sudo rmmod -f iwlagn sudo modprobe iwlagn", I get this read out for my wireless card.
*-network DISABLED
description: Wireless interface
product: WiMAX/WiFi Link 6050 Series
vendor: Intel Corporation
[code]....
In the ubuntu help section it tells me to flip a manual wifi switch to enable it, but pressing my windows wifi button, F2, doesn't appear to do anything while in ubuntu. The only experience I have working with linux is typing some terminal commands on my android phone to root it.
My Intel Corporation WiFi Link 1000 Series wireless card stopped working yesterday after I did an update via Update Manager.After the upgrade, wireless is disabled and the option to enable it in Network Manager is grayed out. I thought that it might be the new kernel, but changing back to the old kernel I still have the problem.
View 8 Replies View RelatedI'm running Kernel 3.0 and i cannot use my TP-Link TL-WN821N v2. # lsusb Bus 001 Device 003: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 [Atheros AR9001U-(2)NG]
[Code]....
ifconfig wlan0 up doesn't work. With kernel 2.6.39 I can use it.
my mate "polish dave" came round and hooked his laptop to my network 02wireless with WEP enc, using backtrack he had my password within 15mins.. now i want to copy him and see just how easy it is my 'acer aspire one' comes with a built in atheros ar5b95 wireless (useless) that i cant get backtrack to find.. i bought a tplink usb and now i cant get that to show up either.
View 4 Replies View RelatedI have only had a few weeks worth of experience with linux, so I'm probably considered a newbie at this but I felt like giving it a shot. I just configured my new Toshiba Satellite A505-S6969 to jaunty. Most of the transition is going well but I'm stuck with a few issues, one of which is getting my wifi to work. Right now I'm working off of an ethernet cable.spci returns
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port
[code]...
I want to install the DLink N150 (DWA-125) Wireless USB adapter in Ubuntu 9.04 if if go to
system-> administrator->log file viewer->dmesg
[ 8.840794] type=1505 audit(1286918554.305:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2041
[code].....
i don't know how to enable wireless.
I have "D-Link DWA-125 Wireless 150 USB Adapter". I can use this wireless adapter on my laptop, i can use it on my desktop as well but only when windows is running, im a newbie to fedora, today is my 2nd day and 3rd night, so pretty exited about it. i have installed fedora 13 on a different hard-disk on my desktop. when the computer is booting, there is an orange light on the adapter glowing, it turns off when the computer reaches the fedora loading screen. If i see fedora's Network Configuration window under the hardware's tab i see the "D-Link DWA-125 Wireless 150 USB Adapter" listed along with my lan card. Now if i go towards the clock on the top right to get the wireless connection working, it shows wireless network disconnected. I have tried creating wireless connection manually by inserting the SSID, macadress, BSSID, ,WPA passkey etc, but still doesnt works. when i try connecting using hidden wireless connection, i receive window for inserting keyring password again and again, stating that the login password does not match. but during all this time, i still havent seen the orange light glowing activity on the external usb adapter. If i restart the computer in windows the adapter/wireless connection works. also have checked the Network service, it seems that the service is up and running. i really require some assisstance on this,
i have noticed this, that if i go under network configuration. the first tab over there, inside devices i cant see my D-Link adapter, but if i switch onto the hardware tab it shows my lan card as well as my D-Link adapter. so does it means that the driver is missing? or any service which is disabled, however at this point of time i can get only using wired connection. please assist me. with this issue, im also downloading the 500 complete update as well for fedora, hoping that it may make it work.
I've a damn TP-LINK WG422G UBS Adapter that i love i installed latest compat-wireless driver package and used latest ar9271 firmware after that it was worked properly. There is no problem when surfing the net, the problem is occurring usually download something via torrent sometimes form websites. I'm starting to download and then usb adapter suddenly freeze. If i remove and plug in the usb adapter it is working again.
View 1 Replies View Relatedhow to install D-link dwm-152 (3G/HSDPA) usb adapter on Lucid Lynx?
i've run lsusb and the result are:
Bus 005 Device 002: ID 0a5c:2162 Broadcom Corp.
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[Code]......
Have tried methods from every thread I could find for past 10 hrs. Have tried installing rt3070sta etc.Monitored message log; appears that the driver isn't recognized, though the USB port sees that something is plugged in (when I plug in the adapter, and unplug it).All of the threads miss something; I can't get a wireless port listed under ifconfig no matter what I try. Seems that every method leaves out something (I guess because everyone's box is different in some way). Network manager doesn't help much. Downloaded Wicd, which does even less.I guess I could try ndiswrapper, but I'm scared away by the hundreds of pages I see on going that route; I'm almost certain it wouldn't work (1000 possible points of failure).Does anyone have a strategy to recommend?AM64 box, newly installed Edubuntu 10.04, ran update manager.
View 3 Replies View RelatedI'm having some issues getting connected with a TP-Link TL-Wn727N wireless USB adapter. I have no way to connect hard wired with the computer, but I have another working notebook to possibly download files. However, the second notebook is a Mac, so most of the posts I've found are not filling in all of the answers. Also forgot to note, I am using Ubuntu 10.10. I followed along with this and managed to get the card to find the wireless connection. However, the connection would never connect. After entering the security password the wireless icon would do it's thing and then pop up asking to ok the password again. I double, triple checked the password and it is correct. I found elsewhere that I should probably install wicd. This is where I've run into problems with finding the way to get files that I can download on the Mac and then installed on the Ubuntu computer. I managed to find this forum thread and downloaded this file I transferred the file from the Mac to the Ubuntu with a flash drive and tried to install. First the install said that Network Manager needed to be removed, so I removed it. Next it says "Dependency is not satisfiable: python-urwid." I'm not sure how to go about getting this dependency as it is not showing up in the package manager.
View 6 Replies View Relatedi just installed Ubuntu 11.04 64bit on my desktop. i have a TP Link TL-WN321G (Ver 4.0) wireless usb adapter to connect to my wireless network (i used to use it with Windows XP).As expected (i'd read up a bit before installing Ubuntu), the adapter was autodetected - i could see my wireless network listed in the networks list dropdown, and lsusb showed it too.lsusb identifies "Bus 002 Device 002: ID 148f:2070 Ralink Technology, Corp. RT2070 Wireless Adapter"But i cannot connect to the network. When i select my network, it keeps trying to connect, but never succeeds in connecting.
i tried going through the forums for possible solutions, but most of them deal with how to get it working when the adapter is not detected, or when networks are not shown. Or they are for older Ubuntu versions.i use the same wireless network on my laptop (Ubuntu 9.04), and it has a WPA & WPA2 Personal security, with a password, which i've configured in the desktop as well.
I just buy a usb wifi and I am trying installing it. TP-LINK TL-WN321Gsusb
Bus 004 Device 002: ID 148f:2573 Ralink Technology, Corp. RT2501USB Wireless Adapterhere I can see that is need driver rt73. I have it in synaptic.I installed these package: firmware-ralink, rt73-common, rt73-module-2.6.26-2-686My kernel is:Linux Miros-main 2.6.26-2-686 #1 SMP Wed Nov 4 20:45:37 UTC 2009 i686 GNU/LinuxI have installed wireless-toolsI have Wicd installed.iwconfig iwconfiglo no wireless extensions.eth0 no wireless extensions.
I have tried to install tp link tf3200 network adapter without success . the os is 8.04 hardy loading drivers is new to me. the driver is sundance (i think) and the output from the make command is shown below.
pag@paghomelinux:~$ cd /media/cdrom0/TF-3200/LinuxDriver
pag@paghomelinux:/media/cdrom0/TF-3200/LinuxDriver$ sudo make all
sudo: unable to resolve host paghomelinux
[code]....
may i ask if TP-LINK 150Mbps Mini Wireless N USB Adapter support by Ubuntu? (TL-WN723N) I plan to replaced IBM x60s default wireless adapter, coz it's suffered overheat issued.
View 1 Replies View RelatedI just did a Wheezy reinstall (I just started using LVM on LUKS), but my Ralink RT5370 usb wireless adapter wouldn't work, even though I have firmware-ralink installed. When I click on the Network Manager icon, it lists my home network (WPA2 passphrase) as available, but clicking on it yields no result.
Before the system reinstall, I've been using the adapter with firmware-ralink without problems. As far as "apt-get update && apt-get upgrade" goes, my system is up-to-date.
I tried uninstalling and then reinstalling firmware-ralink (rebooted too), but to no avail. The adapter seems to be undamaged.
Here are a few pieces of info that might be useful:
Code: Select all$ uname -a
Linux watershed 3.2.0-4-amd64 #1 SMP Debian 3.2.60-1+deb7u1 x86_64 GNU/Linux
Code: Select all# lsusb
...
Bus 004 Device 007: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter
[Code] ....
I had my wired internet working ok, but now that's not working for god knows what reason (yes I'm new). I've got my D-Link DWL-G120 usb wireless adapter pluged in but it's not "working". In the Hardare section it shows all the information for it but it shows it as a unclassified device. At this point I'm thinking of buying a bridge and just reinstalling the OS (plus I want to get a bigger Hard drive as I've got it on a 7 GB drive right now).
View 4 Replies View RelatedI've reinstalled Slackware 4 times today because of things I've messed up along my way, after upgrading the linux kernel I've had issues with getting back to desktop, so I'm on a clean slate right now with the exception of installing wicd. I need help since wireless is not working.. My wireless worked fine out of the box with Ubuntu,I don't understand why it is not working now... Using Slackware 13.1, Kernel 2.6.33.4
Code:
bash-4.1# ifconfig wlan0 up
SIOCSIFFLAGS: No such file or directory
[code]....
I started yesterday off wanting to install this USB wifi adapter on my PC (which is mini-itx so has additional pci slots) [URL] it has the Ralink 3070 chipset. I tried everything I found when googling, nothing came close to working, this was in Fedora12. So I gave up and installed Ununtu 10.04, hoping for better luck there. Ubuntu will recognise the presence of a wifi adapter, here's the output from iwconfig
[Code]....
But it sees no wifi networks and generally won't do anything; I don't think it has the right driver. Rosewill does list a (linux) driver and so does Ralink, but again, neither of these come close to working. has anyone gotten this adapter or chipset to work in ubuntu?
I just installed ubuntu (latest version). Everything worked except when i plug the wifi adapter to the computer nothing happens... It wont show up for wireless network... What do i do? This adapter works great on xp, and its a ralink wifi adapter. I dont know which model version i have though because i bought it new on ebay and it never said model info... I also have a netgear wg111t, how would i get this to work as well?
View 3 Replies View RelatedMy laptop has an internal wireless g "adapter" (for lack of a better word) and I plugged in a very cheap and very small ASUS wireless N adapter later on. The ASUS adapter has better bandwidth (again for lack of a better word) but isn't as high quality of a link as the internal adapter is.The laptop appears to be using the internal adapter, but i want it to use the ASUS adapter.
View 5 Replies View Related