Ubuntu Networking :: Wireless Stopped Working On 9.10 (Intel WiFi Link 5100)
Mar 10, 2010
I've got a Dell precision with Kubuntu 9.10. Wifi worked fine on that machine for months, but stopped working last week. I don't know what happened, but I recently did an "apt-get dist-upgrade". That might have something to do with it.
When I boot in Windows, wifi works fine.
Code:
tijl@Smaug:~$ sudo lshw -C network
*-network
description: Ethernet interface
product: 82567LM Gigabit Network Connection
[Code]....
View 9 Replies
ADVERTISEMENT
Sep 20, 2010
my platform Centos 5.3
i did the following
Code:
[root@localhost ~]# lspci | grep Wireless
0c:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
Code:
[root@localhost ~]# lspci | grep Wireless
0c:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
[Code]....
View 3 Replies
View Related
Aug 29, 2009
I have only had a few weeks worth of experience with linux, so I'm probably considered a newbie at this but I felt like giving it a shot. I just configured my new Toshiba Satellite A505-S6969 to jaunty. Most of the transition is going well but I'm stuck with a few issues, one of which is getting my wifi to work. Right now I'm working off of an ethernet cable.spci returns
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port
[code]...
View 3 Replies
View Related
Dec 4, 2010
i'd like to extend that ma intel wifi link 5100 is not detected no more after perform upgrade package( upgrade the kernel too ). when im using command 'lshw -C network' , there is appear to be detected, but not on command 'iwconfig' or even 'ifconfig' it just show nothin. also network-manager no longer show that ma wireless is work properly anymore.
the old kernel : 2.6.25-22 ( my wireless detected and usable )
the new kernel : 2.6.25-23 ( my wireless detected and unusable )
View 4 Replies
View Related
Apr 28, 2011
I'm trying to get my Dell Latitude work with wifi speed >54Mbit/s, and up to now without any success. The router is a Dlink DIR-635, it has 'n' enabled and working (got an apple laptop connecting at 130Mbit/s, can't test the actual throughput though, since it's the only high-speed device).
Here's the device data:
0c:00.0 Network controller: Intel Corporation WiFi Link 5100
Subsystem: Intel Corporation WiFi Link 5100 AGN
Flags: bus master, fast devsel, latency 0, IRQ 43
Memory at f1ffe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
[Code]...
I'm running 11.4, added the compat-wireless recently to be able to run the newes firmware (iwlwifi-5000-5.ucode , firmware version 8.83.5.1 build 33692), but still all I get is 54Mbit/s. I'd like to know if ANYONE ever got the 802.11n speed on linux, and in particular with these intel cards.
View 9 Replies
View Related
Nov 5, 2010
I moved to Berlin recently and I got wireless internet through an access point. I'm supposed to use the laptop's built-in wireless netcard to access the internet. This usually works in windows (connection falls out from time to time), but I have yet to make it work in linux. I'm using OpenSuse 11.3 64-bit and the Knetwork manager. Most of the settings in the network manager are correct, but it keeps wanting to use system certificates for the server. By that I mean it keeps checking 'Use CA System certificates'.
So I can't choose the CA-certificate supplied by my internet provider. I keep removing the check-mark and pointing it to the 'hotzoneCA.der' certificate. I also got a 'personal' certificate, in lack of a better word. Its called 'jacob_collstrup.p12'. The Knetwork manager seems to accept the 'jacob_collstrup.p12' certificate, but not the other one.
I just put the certificates in a folder like this /jacob/home/hotzone/zertifikate/ I can see the network fine using the Knetwork manager, and the signal strength seems ok. Not too good, but it shouldn't be a problem. I might have messed up the system, since I first tried this guide, prior to experimenting with Knetwork Manager:
1. (had to run this one as su)
Code:
wpa_supplicant -w -i wlan0 -c /etc/wpa_supplicant.conf -Dndiswrapper -dd �t
2. (This was supposed to be put in a wpa_supplicant.conf file)
Code:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
opensc_engine_path=/usr/lib/opensc/engine_opensc.so
pkcs11_engine_path=/usr/lib/opensc/engine_pkcs11.so
pkcs11_module_path=/usr/lib/pkcs11/opensc-pkcs11.so
[Code]...
View 9 Replies
View Related
Nov 24, 2010
I'm using a Vaio TT, which seems to use an Intel 5100 WiFi chipset, and a Linksys WRT54G2 (firmwares 1.0.1 and 1.0.4), ubuntus 10.10 and 10.04.
Wifi works fine out of the box. However if the other vaio tt in our office (running windows 7) comes online, my laptop stops being able to make new connections. It WILL stay connected to chat servers, and downloads SOMETIMES continue to work. However all new HTTP requests / ssh connections / rdp connections / pings fail. The laptop still appears to be "connected" to the wifi network.
This may also happen after an undetermined amount of time without the extra vaio. It is not solved by reconnecting or rebooting. Once the extra vaio leaves the building, everything works fine again. This problem does not happen at all if I boot into windows.
View 4 Replies
View Related
Apr 9, 2010
Intel wifi link 5100 not found on sony vaio backtrack 4 vmware I use vmware to load backtrack I have a sony vaio with 5100 AGN wifi card installed in it. I had tried anything to make my wifi work but always show no interface no wireless. I googled it for help for weeks and all i get was download the iwlwifi things and i already installed in it. i even tried many other thing
/etc/init.d/wicd start
/etc/init.d/networking start
and everytime i type ifconfig it just show eth and lo and no wlan0 in it everytime i type airmon-ng there are no chipset interface and ...........thing (forgot) I could find my wireless card name when i type ilg... something i forgot The problem is,i think my linux doesn't reconize the card even i have installed the driver Anything that i can do to make my linux reconize wifi link 5100 agn wireless card?
View 7 Replies
View Related
Dec 14, 2010
I'm dual booting windows 7 64 bit and Ubuntu 10.1 64 bit on my Dell Inspiron 11z with an embedded WiMAX/WiFi Link 6050 series wireless card made from Intel. I only use it for wifi, not 3g or wimax. I installed the latest driver from intellinuxwireless.org, iwlwifi-6050-ucode-41.28.5.1, but it still doesn't seem to work. I ran these terminal commands from another thread:
cd Desktop/wlwifi-6050-ucode-9.201.4.1
sudo cp iwlwifi-6050-4.ucode /lib/firmware
sudo chmod 644 /lib/firmware/iwlwifi*
[code]....
After running "sudo rmmod -f iwlagn sudo modprobe iwlagn", I get this read out for my wireless card.
*-network DISABLED
description: Wireless interface
product: WiMAX/WiFi Link 6050 Series
vendor: Intel Corporation
[code]....
In the ubuntu help section it tells me to flip a manual wifi switch to enable it, but pressing my windows wifi button, F2, doesn't appear to do anything while in ubuntu. The only experience I have working with linux is typing some terminal commands on my android phone to root it.
View 9 Replies
View Related
Jun 14, 2010
I have seen tons of threads on the internet about Ubuntu 10.04 having wireless issues but none of them have lead to me fixing the problem so I decided to come here. I have been able to connect to access points before but sometimes I have to reboot or reboot twice just to be able to see the wireless points and the enable wireless is always greyed out. And if I am connected to an AP or hardwire the connection drops frequently.
View 1 Replies
View Related
Mar 24, 2010
For some reason I don't understand SUSE tells me there are no network devices available. I've checked for any 'firmware' and 'kill' in both boot.msg and hardware information. I've got an ACER Aspire 8935G with WiFi Link 5100 (Intel). The only info I found that could point to the reason is:
[Code]...
There is one more thing that could be related: I've got some touch-buttons to the left of the keyboard that turn wifi and bluetooth on/of. The bluetooth one works, but nothing happens if I press the wifi one.
I also know that this hardware worked on fedora 11 and 12, so it's probably only a matter of settings/additional packages. If you respond, please keep in mind I can't use any internet connection-based commands, as the system doesn't accept the hardware responsible for cable connections either. I can download files if needed.
View 3 Replies
View Related
Mar 26, 2011
I've reinstalled Slackware 4 times today because of things I've messed up along my way, after upgrading the linux kernel I've had issues with getting back to desktop, so I'm on a clean slate right now with the exception of installing wicd. I need help since wireless is not working.. My wireless worked fine out of the box with Ubuntu,I don't understand why it is not working now... Using Slackware 13.1, Kernel 2.6.33.4
Code:
bash-4.1# ifconfig wlan0 up
SIOCSIFFLAGS: No such file or directory
[code]....
View 13 Replies
View Related
May 4, 2011
I am running (K)Ubuntu Lucid 10.04 64bit on a Dell Latitude E6400, WiFi Card Intel 5100. Never had any problems with networking. Up to about 2 weeks ago. I do realize there have been quite a few posts with this network adaptor, but non really described the problem I have here.
What happens is that suddenly the WiFi LED on the computer stops blinking, the WiFi connection gets disrupted, and the device is not recognized anymore when checking ifconfig. Only cold restarting the machine helps then... it will work for a while (between 1 and 20 minutes) and then crash again.
On Windows 7 the card works perfectly fine. With Ubuntu 11.04 in Live CD mode I have the same effects (connection crashes after a while). Also tried booting an older kernel, no success.
My exact hardware:
Code:
I notived the following problems in /var/log/kern.log
Code:
View 4 Replies
View Related
Oct 11, 2010
Since I originally started using Ubuntu (10.04) I have had problems with my wireless card. Now I have updated to 10.10 and it has stopped working entirely. I am using a "Dell Vostro 1520" with an "Intel(R) WiFi Link 5300 AGN" wireless card.Here are the details: 10.04
In this distribution version, if I had the wireless switch on my laptop activated at startup my wireless card would refuse to activate. There is a light to show when it is activated and this was off, but I checked anyway and wireless capabilities don't work when it is in this state. It didn't even resolve the problem when I switched it off and on again (although this caused the wireless indicator to blink on for less than a second when switched on).This was manageable because I found two workarounds:
1. Wait until my laptop had logged into Ubuntu, then activate the wireless card which would start and work as it should.
2. If I had already logged into Ubuntu I could put my computer on standby, switch off the card, come out of standby and reactivate the card while Ubuntu was running.As I said, this was completely manageable, and I got used to it. 10.10
Now that I have upgraded to 10.10 all workarounds fail, I can't use a wireless connection in Ubuntu, as my card won't activate, I cant even get the light to blink as I could before. The only way I can use WiFi is by switching to Windows.I tend to use Ubuntu for my university programming work.
View 8 Replies
View Related
Jun 7, 2011
I just installed Fedora 15 yesterday and can't get wi-fi to work. When I click 'on' on the Wireless label, it goes back to 'off' immediately. When I open the Network Settings menu and disable Airplane mode, the Wireless connection goes on and then off immediately. I took a look at /var/log/messages and it shows this:
[Code].....
View 5 Replies
View Related
May 31, 2011
My Intel Corporation WiFi Link 1000 Series wireless card stopped working yesterday after I did an update via Update Manager.After the upgrade, wireless is disabled and the option to enable it in Network Manager is grayed out. I thought that it might be the new kernel, but changing back to the old kernel I still have the problem.
View 8 Replies
View Related
Jun 7, 2011
as per pytheas22, i'm attaching few details here. my download speed would starts at 470 kB/s and gradually decreases until it reaches 116 kB/s. Loading web pages seems to be fine.
[Code]...
View 5 Replies
View Related
Nov 9, 2010
I have a Dell Latitude E6500 running Opensuse 11.3. As far as I can tell the module for my wireless card is loaded correctly and it's working:
Code:
sudo lspci | grep -i wifi
0c:00.0 Network controller: Intel Corporation WiFi Link 5100
Code:
[ 556.642557] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:d
[ 556.642560] iwlagn: Copyright(c) 2003-2010 Intel Corporation
[Code].....
The funny thing is that it works fine in a Fedora installation, which has an older kernel and older drivers, on the same laptop. The fact that the indicator light doesn't come in when the physical switch is turned on suggests it's something to do with that switch.
View 6 Replies
View Related
Nov 26, 2010
EDIT 6 Dec: More detailed log from wpa_supplicant I'm using Ubuntu Studio 10.10 x64. I want to get wireless networking going manually. My wireless networking works successfully in Windows 7 x64. I can get it working successfully without encryption but when I try and use WPA-PSK, wpa_supplicant gets stuck in a loop between GROUP_HANDSHAKE and COMPLETED, as shown in the log below.
I've been working mostly off the instructions in this post: [URL]... My laptop is a Dell Studio 1537. It has an Intel Wifi 5100. I'm connecting to a F5D7633-4 router running F5D7633-4Av1_UK_1.00.010 firmware, which is the latest version of the firmware I can find. When I set up WPA, it uses encryption technique TPIK. The other generic information is
Code:
$ iwconfig wlan0 up
04:00.0 Network controller: Intel Corporation WiFi Link 5100
$ lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 045e:074f Microsoft Corp.
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[Code]...
View 1 Replies
View Related
Feb 23, 2011
I have a new Thinkpad t510 laptop with an intel centrino wireless N card (no bluetooth). I installed ubuntu a couple weeks ago after I got another hard drive in the expansion bay. I have the drive partitioned into two sections, 250gb for file storage, and 250gb for the linux OS. Currently no other OS is installed on the other harddrive.
I have had everything perfect for the past couple weeks, but once i installed some updates today, my wireless fails to work now. Just some general info that you might ask me, lspci | grep Network, returns
00:19.0 Ethernet controller: Intel Corporation 82577LM Gigabit Network Connection (rev 06) 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 Furthermore, on the top right of my screen, my wireless is grey'd out and says no network devices available on hover.
[Code]...
Im trying to connect to my college wireless network. I have looked a thinkwiki and no one has posted any bugs. Any ideas on getting it working again?
View 1 Replies
View Related
Aug 11, 2011
I'm new to linux. I've just installed Ubuntu 11.04. It has all been going ok, but the wireless just stopped working all of a sudden. The indicator light turned off and when I tried to turn it back on (Fn+F2) nothing happens. Sometimes, when I restart the computer, the wireless might work; but if the signal is lost the LED on my laptop turns off and I cannot reconnect. Also, in these strange cases that the wireless works when I restart I can manually turn it off (Fn+F2), but nothing happens when I try to switch it back on.
In the menu on the upper right corner I see 'Enable Networking' is checked, but 'Enable Wireless' cannot be modified.
I have a Dell Inspiron 6400 and the wireless device is an Intel Pro/Wireless 3945ABG.
I have tried to follow some of the threads on this forum on similar cases, but the ones that were comprehensible to me did not work (or I actually might not have understood them either). code...
View 1 Replies
View Related
Aug 23, 2010
In simple, I have tried everything I can find on this issue, but I am still unable to get it working on my HP DV4 laptop. My laptop has a Intel 5100 wireless card, and it always says that wireless is disabled. Ive tried booting with the wireless switch off, with it on, ive reinstalled the driver and did everything in a post I found here (cant find a link) that basicly had me reinstall the driver from intels site, then reload the network manager, to no prevail. Im running ubuntu 10.4.1 (just installed), and this is really a big issue 4 me.
View 1 Replies
View Related
Sep 27, 2010
Recently got a Zareason Teo netbook. Wireless came disabled (huh?).
Using Ubuntu 10.4
Wireless: Intel Wireless WiFi Link 5100
iwconfig
lo no wireless extensions.
[Code]....
View 3 Replies
View Related
Oct 23, 2010
My wireless worked out of the box for the past few months. When I was running low on battery recently, I put the laptop to sleep. When I woke it up, there was a black screen with a flashing underscore. I pressed a bunch of buttons but nothing happened. Then suddenly it said something about a wireless hardware error and I did a hard reset by holding down the power button. When I turned the computer back on, wireless was greyed out. There's no hardware switch to enable and disable wireless and the software switch had no effect. I tried echoing into the 'state' of the adapter but it didn't let me. When I tried sudo ifconfig wlan0 up it gave me the following error:
Code:
SIOCSIFFLAGS: Unknown error 132
lspci:
[code]....
View 2 Replies
View Related
Dec 7, 2010
I have just switch to Ubuntu on my laptop from Windows 7 and I am experiencing alot of wireless dropping.
The signal itself is full and I am very close to the router.
What could be the issue and how do I go about rectifying it.
Laptop: Dell 13z.
Wireless: Intel 5100 agn
Ubuntu 10.10 x64.
View 5 Replies
View Related
Feb 18, 2011
I have Ubuntu 10.10 on a thinkpad X201. Wireless was working, but has stopped. It still works in windows, so it is not a hardware problem. iwlist wlan0 scan sees the available networks, but I cannot associate with any of them, including my own.
Last night was my first attempt to connect to a secured network, and nm-applet failed to make the connection even after entering the WEP encryption key and SSID. By turning networking off in nm-applet I was able to manually bring up the connection by editing /etc/network/interfaces and using ifup wlan0. (nm-applet seemed to be interfering as long as networking was turned on there.) Wireless was working perfectly until I rebooted. Now I can't get it to work at all. (There were some partially completed security updates which completed when I rebooted. I hope this wasn't the cause of the breakdown.)I notice that wpa_supplicant is always running. I tried killing it in case it might be interfering with the connection process, but something keeps restarting it.
View 1 Replies
View Related
Jul 26, 2009
how to set up wireless networks. The technical language is foreign to me. My notebook maybe described as follows:
Make and Model: SONY VAIO FW490
Processor: Intel� Core™ 2 Duo Processor P8700 (2.53GHz)
RAM: 4GB DDR2-SDRAM
Graphics card: ATI Mobility Radeon™ HD4650 graphics card with 512MB vRAM.
[code]....
It came pre-installed with Windows Vista Home Premium but now I have Fedora 11 (w/ Gnome) as the only OS. The router that I am using with an Ethernet cable connected to my laptop is a Netgear 54Mbps Wireless Router WGR614 v7 connected to a Motorola Surfboard Cable Modem. Both worked right out of the box and now I have wired Internet access. RCN is my ISP. I would like to avoid using the Ethernet cable connecting my laptop to the router.
This is what I have done so far:
1. Gone to System>Administration>Network
2. Clicked "New" then chose "Wireless connection" from the list
3. Chose Intel Corp. Wireless WiFi Link 5100 (wlan0) from list. The other option was "Other Wireless Card".
I don't know what to do after this. What should I choose in the windows entitled "Configure Wireless Connection" and "Configure Network Settings" ? I chose Ad-Hoc for mode and entered an SSID name even though I have no explanation for taking these actions. As for the other settings, I simply went with whatever was already selected. At the moment, I lose Internet access when I disconnect the Ethernet cable. I see other wireless networks when I click the network icon on the top right corner of the screen. I don't know how to make my router appear on that list if that's necessary.
View 3 Replies
View Related
Jun 4, 2010
Intel 5100 wireless card doesn't connect on 10.04?
View 1 Replies
View Related
Aug 27, 2010
I've been trying to install the linux driver for my wireless car which is an 'Intel wifi link 4965'. I've followed the literature that Intel provide but I keep running into errors.
(I downloaded the driver from[intellinuxwireless.org/?n=downloads)
View 5 Replies
View Related
May 2, 2010
I have backtrack 4 on vmware player.i have intel (R) wifi 5100 agn wireless card and when i type airmon-ng there is nothing shown on interface..and i have been told i need kernel rebuild..i have kernel 2.6.30.9 so how can rebuild it?
View 10 Replies
View Related
